Search Documents

By R. J. Visintainer, W. L. Whitlock

"Difficulties with the sizing and operation of centrifugal froth pumps are common and the underlying fluid dynamics are complex. Design and selection often relies on previous experience, offering unreliable guidance for novel applications or unexpected problems. The current paper describes a program of extensive laboratory testing on froth handling centrifugal pumps, covering a range of flows, heads, speeds, viscosity, air content and froth stability. Variations in impeller vane design and the effectiveness of an airlock venting apparatus were also examined. The program resulted in a better understanding of centrifugal froth pump dynamics and insight for the troubleshooting of field applications.INTRODUCTION The Challenge of Pumping Froth In pumping mineral processing froth, the handling of large quantities of air within the fluid is often unavoidable. Efforts to reduce the amount of air present at the pump suction, while always recommended for improving pump performance, may have limitations. Some strategies may also carry an economic penalty, such as unwanted process dilution (e.g. due to water spray or injection), or increased capital cost of equipment due to oversized pumps, sumps and/or piping. Froth pumping losses fall into several categories, as described below and represented graphically in Figure 1. • Density effects: Entrained air reduces the pressure created by the centrifugal pump in direct proportion to the reduction in bulk density. This is not a true “loss”, since the head produced by the pump (in meters of froth), may remain unaffected. However, the reduction in pressure often leads to a corresponding increase in pump speed required to drive the system, which itself leads to increased NPSH required by the pump (NPSHR). Furthermore, by adding a gas phase, the overall volumetric flowrate is increased, assuming a fixed quantity of de-aerated liquid being handled. This leads to increased suction velocity which further reduces the NPSH margin by simultaneously increasing pump NPSHR and decreasing system NPSH available at the pump suction (NPSHA). • Viscosity effects: Increased viscosity introduces an additional factor in some froth pumping applications, such as oil sands bitumen froth. Losses result from increased shear stress within the fluid flow, which increase with flowrate. Viscosity also facilitates the formation of airlock by reducing turbulence and allowing individual bubbles to coalesce more easily within the flow stream. Finally, it increases pump NPSHR by increasing local pressure drop in the vicinity of the vane inlet edges. • Airlock effects: Also known as air binding, it occurs when air or gas coalesces within the pump suction or impeller passages and begins to collect there, held by buoyancy forces within the rotating flow field. In essence, the liquid “floats upwards” towards the pump suction against the outward directed centrifugal forces. The airlock acts as a blockage, with corresponding reductions in flow, head and efficiency. NPSHR also increases, due to increased velocity and distorted streamlines in the flow circumventing the blockage."

Jan 1, 2012

By D. Simon

This paper studies the effect of binder type and content on the early age development of cemented paste backfill (CPB). The early age development of the mixtures is analyzed using scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDX). These tests show that the early age development of CPB is sensitive to changes in the paste composition. The properties of the CPB depend on the cement content and hydration time. The quantity of hydration products increases with hydration time for all of the mixtures containing cement. However, the high cement content pastes (at least 50% PC) exhibit complete coverage of the PC grains and mine tailings by C-S-H, while the low cement content paste shows scattered coverage of the PC grains and mine tailings and a higher void ratio.

May 1, 2007

By Tom Barry, Kameron Ray, Dr. Gavin Yuill

Imerys Talc, Yellowstone Mine in Montana faces significant geotechnical challenges such as poor wall quality and local instabilities. These instabilities are driven primarily by the characteristics of the rock mass, but are aggravated by drilling and blasting operations.

Jan 1, 2016

Close spatial relationships between the deposits of the Etheridge Goldfield (23 000 kg of bullion) and various regional geological and geophysical features suggest that genesis of the ore deposits was a multi-stage process that started with magmatic and metamorphic stages in the mid-Proterozoic, climaxed with structural and hydrothermal stages in the late Palaeozoic and terminated with an oxidation enrichment stage in the Cainozoic.This hypothesis permits classification of the Georgetown region into areas likely to contain deposits of the Etheridge type and those unlikely to do so; it is concluded that there is little scope for the discovery of extensions of this field.However, the stratigraphic interval between the postulated source rocks of the Etheridge field and stratigraphically higher host rocks of the Croydon field may contain disseminated replacement gold deposits of the Carlin type. The potential host (Pyritic carbonaceous, and locally dolomitic siltstone of the Candlow Formation) is locally faulted and cut by granitoids and the extension of a mineralised, long-standing zone of structural weakness.

Jan 1, 1981

By Cosmin Carpinisan, Erich J. Hofmann, Stephen J. Hall

"Since presenting a technical paper regarding their unique capabilities in Forged Steel Mill Gearing at the SAG-2006 Conference, Australian heavy engineering company Hofmann Engineering has pioneered a number of new manufacturing processes and design concepts for components of large comminution equipment. These include: 1. Novel design improvements for HPGR Rolls with forged steel tyres and a unique patented tungsten carbide insert designed to improve wear life, enhance autogenous layer build-up, and to reduce breakage & chipping under load. 2. Development of forged fabricated Mill Heads using rolled & welded high-tensile steel plate as alternatives to cast conical mill heads. 3. Insitu Girth Gear measurements for profile and wear via portable 6-axis CMM. 4. Gear and Pinion designs to AGMA-6114 for SAG mills of 38’-40’ diameter to 24MW and for Ball Mills of 26’ diameter to 18MW. The paper presents case studies from the Australian heavy manufacturing facilities of Hofmann Engineering, combined with news of their new gear manufacturing and gearbox overhaul facility in Canada."

Jan 1, 2012

By Thomas M. Barczak

A critical safety component for all underground mining is intrinsic and standing support systems. Specifically, tabular hardrock mining exploits a wide variety of deposits that require various methodologies to safely mine the ore material. Several new support systems have been developed in recent years for hard rock applications which have been modified or applied in a variety of ground control applications. These include prestressing devices, improved cribs, and free standing supports. Various standing support and prop-type systems have been designed for hard rock applications with seismic loading conditions to accept prestressing. The prestressing, using water-filled cells, creates an active load upon installation and is considered essential to maintain support during and after the blasting of the mine faces. Heavy seismic activity is also present in these mines and the prestressing units can provide some energy absorption capability to help preserve the integrity of the support. This paper presents an overview of these innovations in support technology.

May 1, 2007

By A Hekmat, M Fuentes, F Armijo, R Castro, F Rodriguez

Interpreting the behaviour of granular material and simulating the gravity flow are complex processes in cave mining methods. In this paper, a new Cellular Automata based code – FlowSim – is used as a flexible tool to simulate the gravity flow and subsidence zone in block caving mines. The simulation results of the gravity flow model in a real scaled mine as well as a scaled physical model are presented in this study. In this research, FlowSim was first calibrated at a mine, based on the information obtained from smart markers. These markers were located in five points of the second block of the Esmeralda sector, at the El Teniente copper mine, Codelco, Chile. The calibration was performed with the objective of reducing the discrepancy between the extraction zone defined by markers in the mine and FlowSim outputs. Regarding the mine data, FlowSim was calibrated with the minimum error of ten per cent between real and simulated results. Then, the calibrated FlowSim model was used to simulate the flow behaviour of a scaled physical model. This model was constructed in the Block Caving Laboratory of the University of Chile to scale down the same block of the Esmeralda sector with the scale of 1:200. The FlowSim outputs show that this software enables the simulation of the gravity flow of the scaled model with less than five per cent discrepancy in grade and dilution entry to the drawpoints. According to the obtained results, this paper recommends FlowSim as an appropriate tool which can improve the design of production level in block caving and can enhance the prediction of the subsidence zone and dilution entry.CITATION:Castro, R, Hekmat, A, Fuentes, M, Armijo, F and Rodriguez, F, 2016. FlowSim – a versatile flow simulation tool to quantify extraction and design alternatives for block caving, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 645–652 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By R. C. D. Phillis

Conventional stoping in hard rock mining is largely considered an operational environment. This paper suggests that stoping falls within the realm of a project management environment typified by uncertainty, variation, and large numbers of interdependencies. Stoping was then equated to a micro-project with many simultaneous activities that had to be executed accurately using finite resources within limited shift durations in order to reach specific goals. Critical chain project management (CCPM) principles were applied to the stoping activities, and the results showed that the number of blasts per panel can be significantly increased by successfully moving the distribution of work as close as possible to the start of shift. Critical chain principles also assisted in facilitating re-focusing and teamwork among stoping crews as well as between day- and night-shift crews. The main recorded success was in managing inherent protective capacities/local contingencies/fat/buffers that are found in all projects. The impact on mine health and safety (MHS) was significant as individual operators and crews became convinced that they could perform all stoping tasks (activities) without compromising accuracy or speed.

Jan 1, 2011

By Patrik Ericsson

During the 90?s Atlas Copco and LKAB developed a pioneering fully automatic long hole production drilling system based on the Atlas Copco Simba W469 drill rigs. These drill rigs have since then drilled about 8.000.000 drill meters at the LKAB Kiruna and Malmberget mines. In 2005 LKAB ordered three new Atlas Copco Simba W6 C, to complement Simba W469s still in operation. These new Simbas are based on the latest generation computerized drilling technology have proven to meet the expectations of LKAB and now form a base for future automation in Kiruna and Malmberget mines. This paper will present experiences from the introduction of Simba W6 C in LKAB Kiruna and Malmberget mines. The paper will also elaborate on the latest developments in remote access and remote control technology making it a common automation option available for all computerized Atlas Copco drill rigs.

May 1, 2007

This paper describes the economic study of longwall versus bord and pillar mining using all continuous miners for a colliery located at the South Coast district of New South Wales, Australia. In this district longwall mining appears to be a better economic proposition than bord and pillar. The internal rate of return on investment is found to remain approximately constant for each method irrespective of life. The economic importance of percentage extraction of coal is shown to be small for high values of minimum rates of return, becoming more significant as the minimum rate of return decreases.

Jan 1, 1980

By Jeff R. Reinson

The Diavik Diamond Mine is producing diamonds from two orebodies, the A154 South and A154 North kimberlite pipes, discovered beneath the waters of Lac de Gras. Innovative dike technology with appropriate water collection and treatment systems allowed Diavik to start open pit mining of the ore bodies in 2002. To allow planning, engineering, and implementation of sufficient water handling infrastructure, reasonably accurate estimates of groundwater inflow quality and quantity over the life of mine are required. Prior to mining, a numerical model using the continuum approach was developed for regional and site wide water management. After approximately two years of mining, groundwater inflows to the pit were found to exceed those predicted by the base case hydrogeologic model. The most likely explanation was flow through Dewey?s Fault zone. As this fault was not explicitly accounted for in the model, a detailed hydrogeologic investigation was conducted to evaluate its geometry and hydraulic properties. A multi-disciplined approach was used and involved core logging, fluid logging, geophysical logging, packer testing, a pumping test, and water quality sample collection. The results of the field investigation were used to update the conceptual and numerical models and to develop a Discrete Fracture Network (DFN) model to address small scale problems such as flow into future underground drifts. The updated numerical hydrogeologic models predict that up to 70 per cent of the groundwater inflow to the A154 N/S open pit is through the relatively narrow fractured rock zone associated with Dewey?s Fault. Consistent with the continuum model, the DFN model predicts that inflow to a drift excavated in Dewey?s Fault will be approximately 10 times the inflow to a drift excavated in competent rock. The DFN model provides a better understanding of the distribution of these inflows on a local scale over the length of the drift.

May 1, 2006

By Greaves M. C, Amos M. D

A study was made of the instrumentation and technique of atomic absorption spectroscopy developed by Walsh of the Commonwealth Scientific and Industrial Research Organisation (C.S.I.R.O.), Australia.The method was evaluated for the determination of silver in lead sulphide concentrate. The precision of the procedure developed is equal to that of the uncorrected fire assay method and the accuracy is greater.Brief mention is made of the use of this technique for the determination of silver and other elements in ores and concentrator products.INTRODUCTIONThe fire assay method, although accepted on a world-wide basis as the umpire method for the determination of silver in ores and concentrates, is freely recognized as yielding results which are lower than actual due to unavoidable losses.King (1934) investigated the influence of the cupelshape, size and material on silver losses during cupellation. Using 100 mg silver prills he recorded silver losses ranging between l. and 10 per cent under extreme conditions and averaging approximately 2 percent under conditions which might be considered normal. Guerin (1957) made a detailed study, under carefully controlled conditions in a furnace similar to that described by Esdaile (1952), of the effect of temperature on silver losses during cupellation. He concluded that if cupellation were carried out at 840°C., then the amount of lead retained by the silver prill was insignificant and that the silver losses were governed by the equation: Y = 0·055 XO.74where X = the final weight of the silver priIl (mg)and Y = the silver lost (mg)

Jan 1, 1961

By Joseph Poplawski, Christian O’Keefe, Robert Maron

"Unique and difficult minerals processing measurement situations will be described and the application of passive array-based technology for performing these measurements will be illustrated. Examples of these situations include volume flow measurements in froth lines and flotation feed lines with entrained air, slurry lines with magnetite and other magnetic ore, slurry lines with abrasive or corrosive materials, high pressure lines, and slurry and non-slurry lines exhibiting scale buildup. Other situations include measurement of entrained air levels in pipes and in flotation columns. These measurements are achieved through CiDRA’s patented passive sonar array-based technology. This technology performs two independent measurements – flow rate and entrained air amounts. Two hardware implementations of this technology have resulted in a non-intrusive flow and entrained air meter which easily is installed on the outside of the pipe, and a submersible version for entrained air or gas holdup measurements which is used in flotation processes. Recent developments in extending this technology to solve other unique measurement problems such as valve movement confirmation will be covered.INTRODUCTIONThe minerals processing industry faces many unique and challenging process control conditions and environments. In terms of flow measurements, many of these situations are not being properly served by traditional flowmeters such as ultrasonic meters, magmeters, turbine meters, orifice plate meters, vortex flow meters, Coriolis flow meters, and venturi meters. A new class of flowmeters has been developed that solves these unique situations and flow measurement problems. This new class of flowmeter technology utilizes sonar-based processing algorithms and an array of passive sensors to measure not only flow, but also fluid composition. It does so accurately, reliably and without making contact with the fluid. These measurements are performed on practically any type of fluid within virtually any type of pipe.PRINCIPLE OF OPERATIONSonar array-based flowmeters are ideal for tracking and measuring the mean velocities of disturbances traveling in the axial direction of a pipe. These disturbances generally will convect with the flow, propagate in the pipe walls, or propagate in the fluid or slurry. First let us focus on the disturbances that convect with the flow. The disturbances that convect with the flow can be density variations, temperature variations or turbulent eddies. The overwhelming majority of industrial flows will have turbulent eddies convecting with the flow, thus providing an excellent means of measuring the flow rate as described below."

Jan 1, 2008

By Georgia J. Lysay

The Kemess Mine tailings impoundment is retained behind an earthfill and rockfill dam that, when complete, will measure about 140 m in height with a crest length in excess of 1 km. Due to weak foundation conditions, the dam must be raised at a very flat downstream slope approaching 7H:1V. This requires an enormous volume of fill to construct the downstream shell of the dam, which has a low permeability clayey till core and is raised via the centerline construction method. For the initial years of annual dam raising, from 1996 through 2002, the downstream shell of the dam was constructed with non acid generating waste rock from the open pit, 7 km distant and requiring an uphill haul with obvious cost implications. To reduce costs, and to reduce waste haulage constraints on mining schedules, feasibility studies were initiated for raising of the downstream shell using cycloned tailings sand as opposed to open pit waste. This required inclusion of flotation cells for removal of residual sulphides from the tailings to produce the non acid generating product mandated for the downstream shell of the dam. These studies were positive, and cycloned sand construction was initiated in December of 2002. This paper describes the experience gained with cycloned sand construction for the dam. Unique aspects include environmental controls given the sulphide-bearing ores, preparation of the existing shell of the dam for subsequent placement of hydraulically placed cycloned tailings sand, on-dam settling ponds, water management issues, reclamation of the sand dam for erosion control commensurate with the wet climate, and use of the system to construct an above-water beach of non acid generating tailings to increase the closure security of the structure. A particularly unique aspect of the Kemess experience is hydraulic fill operations extending throughout the coldest winter months, as compared to other operations where such placement has traditionally been considered non-viable through the winter months

May 1, 2007

By H Zhou, T Honeyands, M Zhou

In iron ore sintering, packing the granules onto the sintering strand to form a porous bed with optimum permeability is a complex dynamic process. The packed bed voidage is the key factor determining the flame front speed and the final sinter productivity and quality. Previous studies have found that granules are soft quasi-particles with a typical structure of nuclei with an adhering fines layer. The deformation of the adhering layer greatly affects the bed voidage during packing, which is related to the strength of the adhering layer and the force exerted on the granules. In this study, tablets simulating the particle size distribution in the adhering layer of granules were made for four single ore blends. Both the tensile strength and shear strength properties of these tablets were investigated as a function of water content by the uniaxial compression test and direct shear test respectively. The results of compression tests show that the adhering layer becomes weaker and more compliant with the increase of moisture. The most porous ore has a more rigid adhering layer than the other three tested iron ores at any given moisture content. In direct shear tests, the internal friction angle of the adhering layer ranged from 31° to 37° and varied little with the moisture content or ore type. The cohesion constant is around 1 kPa and is quite small compared to the stress applied to the granules during packing. Combined with the results of granulation and packing experiments, the influence of the adhering fines layer deformation on the degree of voidage loss is specifically discussed.CITATION:Zhou, M, Zhou, H and Honeyands, T, 2017. Tensile strength and shear strength properties of the adhering layer of granules in iron ore sintering, in Proceedings Iron Ore 2017, pp 117–112 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By C. O?Connor

With ever-increasing global demand for mineral resources, numerous mines are moving towards developing and mining deeper, more complex and lower grade ore bodies. In many cases, mass mining methods (e.g. block caving) are being considered to deal with deeper, lower grade deposits. The body of practical knowledge, however, related to the impacts mass mining methods have on the surface environment in terms of rock mass response, subsidence, etc., is limited, imposing both economic risks to the mine and safety risks to mine personnel. This paper presents the framework for and preliminary results from a large collaborative research initiative between Diavik Diamond Mines, Rio Tinto, the University of British Columbia (UBC) and Simon Fraser University (SFU). The project involves the integration of available subsidence, rock mass, mine operation and monitoring data, together with the advanced application of combined finite/discrete-element modelling codes capable of simulating fracture behaviour, cave propagation and surface subsidence above block cave mines. The main objective of this work is to develop advanced numerical modelling methods to characterize complex rock mass behaviour above block cave mines. The research will also include the study of rock deformation mechanisms associated with the transition from surface to underground mining and the potential interaction between simultaneous open-pit and underground mining operations.

May 1, 2007

By W. Robert Thompson

Hurricane Katrina caused significant damage to transportation structures on the Gulf coast in August, 2005, including the destruction of the US 90 Bridge over Biloxi Bay, Mississippi. Part of the successful design/build proposal for the replacement bridge included a comprehensive test pile program of indicator piles and load test piles in the geotechnical investigation program. A total of 22 indicator piles were installed on the project using the pile driving analyzer to monitor the pile behavior. Five load tests were performed: two axial Statnamic, two lateral Statnamic, and one static axial. The results of the test pile program established driving criteria for production piles that included end-of-drive blow counts and pile tip elevations with an appropriate allowance for setup. The program also confirmed that the planned installation equipment and techniques of GC Constructors, a joint venture of Massman Construction Co., Kiewit Southern Co., and Traylor Bros., Inc., would install the piles to the design tip elevations before production piles began. An extensive program of restrike measurements at a range of times after initial driving of the indicator piles provided a systematic documentation of pile setup in the soil profiles on the site. These resistance values were used to develop a dimensionless setup factor ?S? as the ratio of the restrike resistance to the end of drive resistance. This factor varied from 1.5 for piles penetrating clays and tipped in sand to 3.0 for piles bearing completely in clay and helped establish an end-of drive blow count that included an allowance for setup. The CAPWAP analyses of restrike data with setup and the load test data were used to confirm the design unit side shear and end bearing values developed from the borings and static capacity calculations and to select the design pile lengths.

Jan 1, 2009

By Jay F. Colinet

Researchers at the Pittsburgh Research Laboratory (PRL) of the National Institute for Occupational Safety and Health (NIOSH) work to reduce respirable dust exposures in mining operations. One focus of this research is silica dust control for surface and underground operations in the metal/nonmetal mining industry. PRL researchers analyze dust sampling results from the Mine Safety and Health Administration (MSHA) to identify high-risk occupations to guide research efforts. Research is then conducted in an effort to improve existing technologies and/or develop new controls for reducing worker exposure to airborne silica dust. During the last few years, PRL researchers have conducted research related to the following goals: improving protection provided by enclosed cabs on mobile surface mining equipment, reducing dust generation from surface drills, reducing dust levels in iron ore operations, and developing a new method to clean dust from workers? soiled clothes. A description of each of these controls and subsequent dust reductions quantified through site surveys will be provided.

May 1, 2007

By Steve Kral

For an industry that provides more than half of the nation’s energy needs, the U.S. coal industry still attracts negative publicity. However, the nation’s energy appetite continues to increase. And political leaders and the public are beginning to understand that alternative fuels will not be enough to keep up with that appetite. Does that mean the nation will now embrace the coal industry? No, according to speakers at the Rocky Mountain Coal Mining Institute (RMCMI) meeting. The industry still needs to sell the public on coal’s advantages over other fuels. And the industry must continue to develop technology that will allow coal to meet and exceed strict clean air and clean water regulations.

Jan 1, 2002

By Priyadharshini M. R., Premalatha K

"Abstract With the development in the construction of heavily loaded structures, the necessity of pile foundations has increased. For the transfer of heavy loads, it is mandatory that the piles need to be socketed in the underlying rock strata. The load transfer in bored rock socketed piles is by end resistance or the combination of shaft and end resistance which in turn depends on the length of the rock socket. The determination of socketing length of the pile at present is mostly based on a few factors which affect the pile load transfer mechanism. The effect of all the possible factors involved, need to be studied in proposing guidelines for the design of rock socketing length of the pile. Analyses are carried out using finite element analysis software (PLAXIS 3D Foundation) to understand the influence of the thickness of overlying strata for different socket lengths of piles in weak rock. From the load settlement curves, the influence of the overlying soil on the rock socket length isobserved and an effective rock socket length is proposed.IntroductionThe determination of socketing length of the pile at present is mostly based on a few factors affecting the pile load transfer mechanism, which sometimes give a better design and sometimes an uneconomical design. Too much socketing length results in more construction time and higher costs. Therefore, the effect of all possible factors involved need to be studied in proposing guidelinesfor the design of t h e r o c k socket length of the pile.The factors that affect the termination criteria of the rock socketed pile are the capacity requirement, thickness and properties of the overlying soil, characteristics of the founding strata, drilling tools used, roughness of the rock socket and nature of loading.A comprehensive study was performed to understand all the above mentioned factors in different types of rocks. In this paper discussion is made on the settlement results, specifically the influence of overlying sand of different densities above a weak rock. The influence of stress developed is not discussed, keeping in mind the size of the paper under study."

Jan 1, 2014