Search Documents

By Dezhong Kong, Jaichen Wang, Shengli Yang

"The stability control of longwall coal face is the key technology of large-cutting-height mining method. Therefore, a systematic study of the factors that affect coal face stability and its control technology is required in the development of large-cutting-height mining method in China. After the practical field observation and years of study, it was found that the more than 95% of failure in coal face are shear failure. The shear failure analysis model of coal face has been established, that can perform systematic study among factors such as mining height, coal mass strength, roof load, support resistance, and face flipper protecting plate horizontal force. Meanwhile, sensitivity analysis of factors influencing coal face stability showed that improving support capacity, cohesion of coal mass and decreasing roof load of coal face are the key to improve coal face stability. Numerical simulation of the factors affecting coal face stability has been performed using UDEC software and the results are consistent with the theoretical analysis. The coal face reinforcement technology of largecutting- height mining method using the grouting combined with coir rope is presented. Laboratory tests have been carried out to verify its reinforcement effect and practical application has been implemented in several coal mines with good results. It has now become the main technology to reduce longwall coal face failure of large-cutting-height mining method.INTRODUCTIONLarge-cutting-height mining method of more than 3.5m mining height, is one of the main methods for thick-seam mining in China. Currently, the largest mining height is 7.3m and the support capacity is 1,800mt. Shendong and Jincheng mining area have the best use of large-cutting-height mining technology (Wang, 2009). Generally, the mining height ranges from 6.5m to 7m and the support capacity ranges from 1,000mt to 2,000mt, annual output of the panel is between 10 and 12 million tons and the highest are 15 million tons. The main goal of large-cutting-height mining technology is to achieve high yield and high efficiency by increasing the advancing speed of longwall face (Yuan, 2011- 2012). However, in certain geologic conditions, rib spalling and roof falls in the unsupported area often occur. Because of the large tonnage of large-cutting-height mining equipment, once the rib spalling and roof falls cause the equipment to be out of alignment, the face advancing speed could be affected seriously that in turn affects the output (Yang, 2012). Therefore, studying the failure mechanism and control technique of coal face in large-cuttingheight mining method is of great significance."

Jan 1, 2015

By F. K. McKean

Abstract A discussion of the difficulties involved in the production of a clean molybdenite concentrate introduces the paper. There is a brief description of the various methods for producing molybdenite that will fit marketing specifications, and it is shown how these methods are nor suited to the milling of ores containing small quantities of bismuth and copper. A process that was developed in the ore testing laboratories of the Bureau of Mines at Ottawa for the La Corne mill of the Molybdenite Corporation of Canada is described in derail and some results from pilot plant operation of this milling scheme are tabulated. A description of the La Corne mill, where the writer supervised the introduction of the process on a commercial scale, adds to the interest of the paper. In conclusion, there is a review of the conditions necessary for proper operation of the flowsheet. An attempt is made to show how the process might be satisfactory in other problems similar to that at the La Corne mill. Introduction The production of a molybdenite concentrate, free from impurities and high in grade, has been a difficult task when milling some types of ore. Whereas ordinary flotation techniques will produce acceptable concentrates of the baser sulphides, in many cases they will not serve in the treatment of molybdenite, for this mineral must be of optimum grade and purity to bring the best prices, or to find a market at all . Faced with the necessity of meeting stringent specifications, the mill operator has been forced to employ expensive processing methods, and to be satisfied with low recoveries, in order to make grade with his product. The most objectionable and common impurities found with molybdenite are: (a) gangue minerals and iron sulphides, which lower the grade; and (b) copper, bismuth, or antimony, which are deleterious in the final uses of the molybdenite products. It is difficult, and sometimes impossible, to market a concentrate with over 0.5 per cent of any of the latter impurities, or with a grade much below 90 per cent MoS2. Various methods, which have been highly successful in specific applications, have been developed to meet the problem of producing a suitable concentrate. All of them, however, have certain defects precluding their use when treating ores of a nature different from the one for which they ? were designed. The writer has developed a process for molybdenite ores having an objectionable impurity content. A description of the procedure involved, and of the La Corne mill of the Molybdenite Corporation of Canada, where the process has been adopted, should be of interest to flotation operators.

Jan 1, 1947

By N. Skopak, W. Birch, A. Douglas, C. Johnson

Determining the origins of air overpressure has been a long-debated topic within the explosives engineering community. Historically, it has been accepted that the initial face movement gave rise to air displacement, resulting in an air overpressure pulse. Later research proposed that the air overpressure pulse resulted from the shockwave rapidly propagating through and impacting the quarry face. Most recently, researchers have derived that air overpressure is associated with the gas phase from which a gaseous product from explosives rapidly pours out the quarry face under high pressure. Significant research has strongly indicated that the time at which the air overpressure pulse exits the face fails to coincide with either the arrival of the shockwave at the free face or the initial face movement. Research has consistently shown that the shockwave arrival at the face occurs before the air overpressure pulse leaves the face. Therefore, to best determine which blast mechanism contributed to the initial air overpressure pulse, testing was aimed at verifying the precise time at which the air overpressure exited the faces compared to when the face first moved. This research describes tests using scaled concrete blocks, which provided the ability to control the key parameters necessary for the research to be successfully concluded. Black powder was selected as the energetic material to eliminate the production of the detonation wave while still inducing other gas-producing effects. The components evaluated were air blast arrival times in front of the face, the initial movement of the blast face, the precise initiation time of the blast hole, timing of pressurization within the rock mass (between borehole and face, or adjacent borehole), and the speed of sound in the air. A detailed timeline was created which portrays the actions within the blast to promote an understanding of the sequencing of events. The results showed that the initial face movement occurred at 17.57 milliseconds (ms) while the calculated time at which the air overpressure exited the face occurred at 7.07 ms. The large disparity continues to reaffirm the premise that the origin fails to coincide with the air pressure pulse. Average pressurization through the block occurred at a rate of 341.23 feet per second (104.15 meters per second) which resulted in the gas release pulse being calculated to exit the face between 4.41 and 6.21 ms. This pulse correlates more accurately with the air overpressure origin timing which will be the focus of continued research. Knowing the precise origin of blast-induced air overpressure will assist in being able to better control it through appropriate blast design.

Jan 1, 2024

By C V. Deutsch

"Geometallurgical variables often cause problems to conventional geostatistical workflows. There are many variables; some are compositional and some are non-additive. They often show: complex multivariate relationships undersampling relative to conventional grade variables unequal sampling; that is, all variables are not available at all data locations.A variety of approaches have been developed over the years, but geostatisticians remain mostly focused on modelling rock types and a few grade variables with an abundance of data. The problems are reviewed and a chained workflow is presented where appropriate techniques are employed in sequence to permit reliable spatial prediction of geometallurgical variables. The spatial models may be used to assess the value of additional data, for prediction of process performance, for improved mine planning and other optimisation tasks. The chained workflow will include data transformations such as ratios and normal scores that make the variables amenable to geostatistical modelling. Data imputation techniques to account for missing values are considered with special consideration to spatial correlation with the available data. Decorrelation techniques such as the principal components, min/max autocorrelation factors and projection pursuit multivariate transformation are employed to manage massively multivariate modelling. Full distribution modelling must be considered to avoid biases in the prediction of non-additive variables. The post-processing of geometallurgical models must be streamlined for robustness and efficiency. The precise workflow varies according to the specific purpose of the study. Guidelines and thoughts on best practice are presented.CITATION:Deutsch, C V, 2013. Geostatistical modelling of geometallurgical variables - problems and solutions, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013, pp 7-16 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Sep 29, 2013

By Fred Horne

1N THIS PAPER, the writer proposes to limit his comments to few generalized phases of the subject, based on his personal experience in the midwestern United 'States and in one section .of the Coal Branch in Western Alberta. The following statistics are submitted to show the importance that strip mining has assumed in the coal mining industry of the United States. In 1914, 1,281,000 tons of strip coal were produced, amounting to 0.3 per cent of the total production. In 1948, the total was 13~,505,000 tons, representing 23.3 per cent. In 1949, the percentage figure dropped slightly and this can be partially accounted for by the labour disturbances prevalent throughout the year. In 1914, there were 48 power shovels and draglines being used in the stripping of coal; in 1949 there were 3,712, not to mention other types of coal stripping equipment such as bulldozers, tractors and scrapers, rotary excavators, and stackers. At the bituminous coal mines in Western Canada, strip mining was introduced only a few years ago, two of the major reasons for its development being the need for increased production during the war and post-war years and the need to hold the line on increasing production costs, but even in these few years the percentage of strip production has in-creased to such an extent that some mines that, five or six years ago, were producing all their tonnage from underground operations are today obtaining up to 80 per cent of their total output from strip mines.

Jan 1, 1951

By Qing-hua Tian, Li-then Cheng, Xue-yi Guo

In order to recycle valuable metals from silver separated residue, a novel method using alkaline smelting at low temperature was proposed. The main factors affecting the main metal recovery such as the smelting temperature, smelting time, liquid-to-solid ratio and alkali addition were investigated comprehensively. The behavior of the main metal elements, such as Pb, Sn, Sb and Bi in silver separated residue was also discussed. The results indicated that amphoteric metals such as Pb and Sn can be smelted into the melt, while other metal elements, such as Sb and Bi were left in the residue.

Jan 1, 2011

By R. P. King

The linear intercept distributions provide unambiguous and accurate characterizations of the texture of mineralogical materials. The relation between the measured linear intercept distributions and the spatial correlation function is shown to be given by: in the Laplace Transform domain. The linear intercept distributions of the two phases in a low- grade chromite-serpentinite ore were measured. and the spatial correlation functions for both phases were evaluated using the above relation. The correlation functions are the primary relations for integral geometric models of mineralogical texture and this work demonstrates the relation between the 10 stereological model and the 3D integral geometry model for mineral liberation.

Jan 1, 1991

Nowadays, the more successful plants are those who have adopted effective and efficient strategies to optimise their plant operation. As the ?heart of the plant? could be viewed as the mil-ling/grinding area, one of the key steps in plant optimisation is, therefore, ensuring the mill is operating properly. In the past, when primary, secondary and tertiary crushers fed material directly to large ball mills, the energy efficiency of the concentrator was determined for the most part by the ball mill operation, whereas now the energy efficiency of a plant often rests largely on the semiau-togenous grinding (SAG) mill operation. As a result, mines have shifted their emphasis in optimization from ball mills to SAG mills. The grinding mill?s energy efficiency essentially depends on ore characteristics and the discharge rate of broken particles, which in turn depends on how efficiently the discharge pump (grate and pulp lifters) operates. The essential function of pulp lifter being to transport the broken material and slurry out of the mill, its design optimization therefore affects the discharge capacity (or mill throughput) of AG and SAG grinding mills. This paper will discuss how the optimised design of the pulp lifter/ discharger has helped to eliminate material transport issues such as flow-back and carry-over of slurry and pebbles to in-crease the energy efficiency of SAG mill using the actual operational data.

Jan 1, 2014

By C Torrisi, J Andreatidis, M Duffy

BHPÆs Cannington process plant was commissioned in October 1997. The Cannington ore contains high grades of silver, lead and zinc but also contains high levels of fluorine which must be removed to produce a marketable concentrate. As a consequence the plant is more complex than the typical base metal concentrator. Some of the features of the Cannington operation include a single stage autogenous mill, multiple stages of flotation cleaning, two leach circuits, pressure filtration and a paste fill plant. The start-up and achievement of design performance for new lead/zinc operations has traditionally taken much longer than for gold or copper operation and is littered with many tales of woe with feasibility targets often not achieved (Agarwal, Brown and Katrak, 1984; Bulatovic and Wyslouzil, 1999; Leung, Andreatidis, Woodall and Alford, 1996; Sherman, 1999; Ward, 1998).

Jan 1, 2000

By M. Hamamoto, S. Tanaka, K. Noda

"Tamano Smelter or Hibi Kyodo Smelting Co. Ltd. is operating with the Tamano Type Flash Smelting Furnace method which is a flash smelting furnace without slag cleaning furnace but which can discharge a slag equivalent to that from the slag cleaning furnace and with the development or coke combustion technology which is the basis of this world's only one type flash smelting furnace process, the smelter exhibits a low operation cost under high productivity operation. Utilizing this experience and improving it we have developed and put to practice an operation guide system using a general purpose computer in order to further establish s stable operation. In this paper these improvements are described. Background of System DevelopmentWith the recent rapid progress of general purpose computers and improvements in their performance an environment for the use or computer in process simulation at low cost and simple operation has been established. If an accurate operation simulation can be done with the Tamano Type Flash Smelting Furnace the merits would be very great and thus we started development of the system. The official name of this system is Computer guide system for Coke Combustion in the T-FSF and taking the initial letters we call it CCCT. We aim to achieve operation with stable mane grade, temperature and slag loss in the furnace by maintaining the most suitable combustion conditions of concentrate and coke in the flash furnace with the assistance of CCCT to the flash smelting furnace operators.Through several production expansion projects clone in the past by oxygen enrichment the copper concentrate treatment quantity and matte grade have increased step by step as shown in Figure I. Following this increase the difference between the operation calculation results al the initial stage of coke combustion and the actual behavior of furnace (matte grade. temperature in the furnace. etc.) gradually became bigger. Further operation procedures taken by different operators against the same phenomenon were sometimes different depending on each individual, which from time to time caused the operation to become unstable. Prior to the development of the system we checked out thoroughly the weak points of operation calculation procedures which were in practice until that time. The results were analyzed and study was carried out to establish a most suitahle operation calculation procedure and finally we reached this system"

Jan 1, 2000

By A Reid, A W. Musk, O Jones

In this paper, the authors attempt to bridge the gap that currently exists between the duty-of-care responsibilities of underground mining industry personnel, and the multifaceted health challenges facing mineworkers in Western Australia’s metal mines where diesel-powered mobile equipment predominate. In addressing this issue, the complexities of the nature and extent of the challenges are discussed along with the current inadequacy of existing regulatory metrics. Support is given to the need for well-organised in-mine baseline studies to clearly define the distribution and aging characteristics of the toxic and carcinogenic pollutants within the mine ventilation system, with special emphasis given to exploring the validity of biomonitoring systems. The paper concludes with the proposal that a template risk assessment data sheet be prepared for the industry to provide mining personnel with a sound basic knowledge of the health risks involved and the control measures and precautions available for minimising and/or eliminating the hazard.CITATION:Jones, O, Musk, A W, Reid, A and Davis, C, 2017. Risk assessment tool for mines using diesel-powered mobile equipment, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 151–154 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

By Patricio Barrios

In February 1996, ATLANTIC, COPPER completed the construction of a Project for Expansion and Environmental Improvements in its Smelter and Electrolytic Refinery located in Huelva. Following the expansion, the new operating concept is based on the simultaneous blowing of two converters, while increasing throughput in the Flash Furnace up to the level required to deliver matte to both converters. While the production level planned with the Project.(270,000 MTPY of copper from concentrates) was reached the following June, work since then has been carried out to optimize the new equipment .and to develop a new operating shedule. This paper describes operational experiences from the start up of the Expansion Project, difficulties encountered and operating improvements introduced, which have allow an increase of production levels up to 300,000 MTPY of copper.

Jan 1, 1998

By R. Cook

Knowledge based applications are becoming important to Associated Manganese for efficiently dispatching ore of appropriate grades to customers on time. The G2 expert system shell has been used to develop blending and scheduling applications using a combination of object-oriented rule based, procedural, and heuristic approaches. The blending application, for example uses a heuristic approach for creating blends from thousands of small stacks of manganese ore of various grades and sizes, to meet customer specifications while fully exploiting the available inventory. Data capture and data warehousing have become important issues, and the Internet shows strong potential for distribution of pre-processed information.

Jan 1, 1997

By Sandra M. Stash

An integrated copper production complex includes mining, milling and smelting facilities which are usually at or near a common site, and sized to complement one another in capacity. There may also be an electrolytic retlnery serving the complex, but not always totally dedicated to its production. Mines and mills without co-owned smelters are not usually considered integrated. The first marketable product of an integrated complex is blister, or in some cases electrolytically refined copper. The nature of integrated operation brings together all of the environmental issues associated with copper production, but currently operating and newly planned facilities are required to anticipate these issues and meet stringent regulations. Older complexes, however, may have legacies of 50 or more years of operation unencumbered by current levels of environmental strictures: nevertheless, they must be remediated. Using examples from closure and remediation of the mining and mineral processing facilities in the Upper Clark Fork River Basin of Montana, the authors review some of the problems encountered since CERCLA's1 enactment in 1980, and the solutions to those problems, bearing in mind that not all of the problems and solutions were technical. Much has been written about the mines of Butte -the "Richest Hill on Earth" as it was known in its day and the mills, smelters and refineries they spawned. These facilities comprised an archetype of the integrated copper complex: from ore to metal in facilities serving and depending on one another. Many great stories of technological innovations and business triumphs have been told about Butte and Anaconda's mining history and the place The Anaconda Company occupies in that history. However, relatively little has been written about the final days: 25 years during which the once-great complex was closed, and the remnants of past glories were remediated after nearly a century of operation. This paper offers some insights from the real world affecting similar complexes still operating, and, hopefully, lessons for others just starting down the path to final closure.

Jan 1, 2003

By G. Beckstead, L. Gormely, R. Zimmer, K. Hanneman, B. Nethery

As part of the EIS and permitting activities for the Pogo Mine in Alaska, a risk assessment study for the water management plan was carried out. The basis for the study was a site water volume and contaminant balance model. Probabilistic modeling was carried out using the @Risk Monte Carlo simulation package to investigate the frequency, quantity, and quality of discharges under varying assumptions. The results were used in discussions with regulatory officials as part of the permitting process for the project. The simulation allows probabilistic modeling of key environmental parameters based on input frequency distributions involving both quality and quantity of flow. When combined with predictions of water treatment plant capacities and removal efficiency, this was very useful for defining the likelihood of important regulatory outcomes. Based on the model, certain project modifications were made. Using the simulation as a basis, ongoing dialog with regulators led to consensus that all potential risks have been considered and mitigated for the Pogo Mine according to their likelihood and severity, and that regulatory requirements would be achieved. The paper describes the model and some of the applications for which it was used.

Jan 1, 2005

By Don Cchultz

The United States Forest Service, as a land managing agency, is responsible for the surface administration of National Forest lands. The basic objectives of management are protection and utilization of renewable resources such as water, forage, timber, wildlife, recreation, and clean air. Much of the National Forest land in this country is open to mineral prospecting and development. When large de-posits of minerals are extracted from the forest environment, especially by surface methods, there are oftentimes conflicts between accepted mining methods and the objectives of other resource management goals. Such is the situation in Southeast Idaho where several members of the phosphate industry are operating on and adjacent to the Caribou National Forest. In 1966, the phosphate industry and the Caribou National Forest became mutually concerned with the problems of rehabilitating mined areas and minimizing potential damage to adjacent forest areas. A Cooperative Administrative Study was initiated with industry supporting the Forest Service financially and with equipment, material, and manpower, as well as interest and enthusiasm. The objectives of the study are to provide basic, applicable information pertinent to: 1. Protecting the quality of water emanating from mined water-sheds. 2. Providing for soil stabilization on mined areas. 3. Returning mined areas to surface resource production. 4. The feasibility of making mined areas esthetically acceptable. It was concluded that the following separate--yet intergrated--fields should be studied in order to obtain the desired information:

Jan 1, 1971

By Tom Paynter

In an underground mining environment, the primary method of firing a blast is using a combination of an electric detonator and a detonating cord to initiate the Nonelectric detonators. This method has been in use since the 1970’s. A firing line is used which can be subjected to damage and the need for constant testing and maintenance.

Jan 1, 2017

By Earl G. Hoover

For most geologists and miners the term "asbestos" refers to a group of highly fibrous silicate minerals that readily separate into long, thin, strong fibers of sufficient flexibility to be woven, are heat resistant and chemically inert, and possess a high electric insulation and therefore are suitable for? uses where incombustible, nonconductive or chemically resistant material is required. The United States Mining Enforcement and Safety Administration (MESA) specifically refers to the naturally occurring minerals chrysotile. amosite, crocidolite, termolite asbestos, anthophyllite asbestos, and actinolite asbestos as "asbestos" if the individual crystal fragments have the following dimensions; length -greater than 5 micrometers, maximum diameter -less than 5 micrometers, and a length to diameter ratio of 3 or greater. Since asbestos has been identified as one of the ten most carcinogenic substances (a cancer causing agent) it has become, for many government regulatory agencies, a major issue concerning banning emissions to the environment.

Jan 1, 1978

By A. L. Engel

This report is a compilation of preliminary and, in some cases, more extensive concentration experiments by the Federal Bureau of Mines on low-and medium-grade fluorspar ores from three localities in Nevada and one in California. The work was done on samples obtained from Shoshone mine, Nye County, Valery mine, Pershing County, and the Broken Hills mine, Mineral County, all in Nevada, and Dirty Weather mine, Inyo County, Calif. These investigations were made to aid in the development of domestic fluorspar resources, in line with the Bureau's long-established program of conservation of mineral resources. The treatment methods employed in the experimental work described included simulated or "heavy-liquid" gravity concentration of coarse minerals and comparatively fine-grained minerals, and flotation concentration of finely-ground minerals. These methods were attempted in order to beneficiate the ores and produce concentrates which could be marketed readily, with as high a recovery rate as possible, while using simple treatment methods suitable for small-scale operation.

Jan 1, 1961

By A. Tobey Yu

The smelter is the heart of a copper producing operation. Its principal function is to reduce and convert raw copper concentrates and/or leach plant precipitates into blister copper before it is refined. In addition to concentrates and precipitates, typical feed to a smelter also encompasses matte chips, flue dust, flux and lime. By nature, the characteristics of these materials are extremely variable, ranging from sub-micron to lumps, from slurry to dust, from abrasive to corrosive and free-flowing to adhesive. Furthermore, as a result of geological formation, most of the world's open pit copper mines are located in a semi-arid zone, where precipitation is minimal. This particular climate compounds the problem of handling these materials.

Jan 1, 1976