Search Documents

By Francisco J. Sotillo

Using new ecological-natural-organic depressant for gangue and pyrite with antibacterial properties (control of acid mine drainage) with new improved xanthate collectors using rheology additive not chemical reacting with xanthate resulted in better sulfide flotation. Rougher-scavenger lead flotation tests were conducted increasing the concentrate grade from 7.07% Pb to 13.44% Pb, enhancing selectivity. Lead recovery increased from 64.08% to 79.38% and 80.40% using only the new depressant, and improved xanthate Z-11 and Z-4, respectively. The results demonstrated that the new depressant was selective and efficient, and the new improved xanthates stronger more selective collectors.

Feb 22, 2026

By Wm. O. Vanderburg

This report on the mining and milling of tungsten ores is the second part of a general study of the domestic tungsten industry. The first part, comprising general information on tungsten, has been printed as Bureau of Mines Information Circular 6821. The purpose of these papers is to increase efficiency in the mining, preparation, and utilization of the tungsten resources of the United States. The tungsten industry forms so small a part of the vast mining and metallurgical operations of the illation that private metallurgists have not had enough inducement to give special attention to the recovery of tungsten minerals from the ores, and many of the small companies are financially unable to undertake research work. A study of the milling of tungsten ores reveals that further improvement is possible, especially in the treatment of slimes. Recent experimental work by the Bureau shows that the flotation process is applicable to certain tungsten ores. The future of the tungsten industry it the United States depends to a great extent on utilization of the low-grade deposits of the contact-metamorphic type.

Jan 1, 1935

By Terry L. Muldoon

This report describes development and demonstration of an upgraded stench fire warning system for underground wines. Current systems, which have been used since before 1920, release an ethyl mercaptan mixture into the mines' compressed and/or ventilation air during emergencies. Miners, when smelling ethyl mercaptan, evacuate the mine according to predetermined plans. These systems, while simple, have problems with safety and reliability. The upgraded system overcomes these problems. The system uses a different stench agent, is less toxic, less nauseating, and less corrosive than ethyl mercaptan. These combined with the feature of thiophane not reacting with iron oxides, makes the upgraded system safer and more reliable. The system also uses a combination of two simple principles: a standpipe with pressure balancing to provide a constant head, and a sized orifice to control the rate of release of the stench agent. This system enables the mine to release the agent for a longer period which provides better coverage and to ensure that miners will not be exposed to potentially toxic concentrations of the stench agent. The system is easy to operate, requiring only the turning of two 1/4-turn ball valves. The upgraded system has been successfully tested during two evacuation drills at an underground uranium mine. Using three injectors (one on the compressed air line and one on each of two intake air shafts), the system exhibited significant improvements in warning times over the mine's existing system. This report provides a detailed description of the system design and its demonstrated performance in two mine demonstrations.

Jan 1, 1981

By William O. Vanderburg

This report3/ gives the results of a reconnaissance of mining districts in Eureka County, Nevada, made from September 25 to October 20 and from October 27 to November 5, 1577. During this time, virtually all the districts were visited and many data obtained on active and inactive properties. This report covers the locations of the various districts, geological background, ownership and brief descriptions of mines and prospects, information on past and current operations, and, other data likely to be useful to those interested in the development of our mineral resources. From the viewpoint of past production in the county, the silver-lead-gold deposits at Eureka have been tie most important, followed by the silver deposits at Cortez and Mineral Hill. The period of greatest activity in the foregoing districts was from 1870 to 1990, when Eureka was one of the principal mining areas in Nevada; the production of lead was sufficient to affect its price in all the commercial centers of the world. Eureka also merits the distinction of being the birthplace of the silver-lead smelting industry in the United States.

Jan 1, 1938

By K. C. McMahon

This report is the result of the engineering efforts performed by the Mining Equipment Operations of FMC to develop methods of automating a continuous miner. This work was done as part of modification number three of the contract for the development of a miner/bolter system. As the demand for energy places an ever-increasing pressure on the coal mining industry to produce more coal, methods for underground mining which will increase productivity with a con-current increase in safety are being actively sought. Removing the machine operator from his station on the continuous miner and placing him at a safer location behind the machine while retaining his control functions via an umbilical cable or a radio link was an important first step. However, the problems of poor visibility, no control "feel", and the judgmental problems of controlling the sump distance and the shear limits have not been conducive to the productivity increase that is desired.

Jan 1, 1975

By A. L. Mular

"IntroductionThe mining industry has made slow but steady progress toward the automation of mineral processing plants over the last 35 years. The stimulus to automate is associated with important economic and hidden benefits, so that today, the latest in instrumentation and technology is being employed.This chapter assesses the status of instrumentation justified economically, defines levels of control and certain fundamentals of feedback control loops, describes typical sensors employed in concentrator circuits, summarizes control strategies employed therein, and briefly highlights trends in integrated plant control.Current Status of AutomationAs early as 1948, the mining industry began to show interest in automation, probably because of its close association with the petroleum industry. By 1958, some regulatory control had been achieved in various sections of a concentrator, particularly in crushing circuits. Successes were attributed primarily to the reliability of sensors employed in the corresponding control scheme. By 1961, computers had appeared on the scene, initially, for data logging purposes.From 1958 to 1965, very few new control strategies had been implemented. Guidelines in vogue at this time appeared to be:- Install proven automation, unless a good instrumentation department exists at the concentrator.- Do not bite off too much instrumentation at one time.- Do not purchase on price alone; instrumentation must function in the concentrator environment.- Do not purchase automatic control equipment to be fashionable.Such guidelines were employed1 because of a lack of: (a) quantitative process knowledge, (b) reliable primary sensors, (c) initiative to try something new, (d) trained personnel, and (e) understanding that older concentrators could justify automation in many situations."

Jan 1, 1989

By Finn Ouchterlony, José A. Sanchidrián

"A model for fragmentation in bench blasting that originates from dimensional analysis of fragmentation in asteroid collisions is presented. Percentiles of the size distribution are obtained in the basic model as the product of a rock strength-to-explosive energy ratio, a bench shape factor, a scale factor or characteristic size and a percentage passing-related factor. The parameters of the model are fitted to 169 bench blasts in different sites and rock types, bench geometries and delay times, for which thefragmentation of the muckpile was obtained by sieving. The basic model is found to significantlyimprove with an additional factor describing the rock mass structure in terms of the spacing and orientation of discontinuities, and another one describing the delay between successive contiguous shots; the latter is conveniently formulated as a function of the P-wave velocity and the holes spacing. The rock strength property chosen is the strain energy at rupture that, together with the explosive energy density in the rock (or energy powder factor), forms a combined rock strength/explosive energy nondimensionalfactor. The model, called xP-frag, is applicable from 5 to 100 percentile fragment sizes, with all parameters determined from the fits significant to a 0.05 level. The expected error of the prediction is below 25 % at any percentile. These errors are half to one third of the errors expected with the best prediction models available to date."

Jan 1, 2017

By Paul Lynch

"Since being reported to the 2012 UMI in Shanghai, the Cook Islands has been steadily developing for the commencement of it Seabed Minerals sector in its large Exclusive Economic Zone which contain a vast and unique Manganese Nodule resource, estimated at 10 billion tonnes1. At the 2013 UMI in Brazil, it was reported that the Seabed Minerals Act had commenced and all the necessary complex Technical aspects of this developmental work was being undertaken. At the 2014 UMI in Portugal, full details of the final developments leading to the opening of the Tender of Exploration Blocks in the Cook Islands EEZ will be presented in a brief but comprehensive method, using Poster displays, Powerpoint and active Website interaction. This will show the drafted Regulations, prepared on best international standards, to address both Licencing and Environmental requirements, to give clarity and security to the Resources Owner, industry and stakeholders. This work in being coordinated by the Cook Islands Seabed Minerals Authority, with the valuable collaboration of many international, regional and national stakeholders, including the Cook Islands NGOs, Marine Resources, Marine Park and National Environment Service."

Sep 1, 2014

By S M. Stewart

Industry, especially extractive industry, must now give serious attention to the impact its operations have on the natural environment and on the economic, social, and cultural context within which it operates.   While this obligation is statutorily managed, there has been a recent shift towards a culture of self responsibility. Industry is now talking about earning its ôsocial licence to operateö and the importance of maintaining the ôtriple bottom lineö, thus adding environmental and social performance to the usual financial criteria used to measure organisational performance. The social context within which companies operate has also become more sensitive with industry responding to a growing public expectation that it conduct itself in a way that strives for sustainability by operating and developing in a way that meets the needs of the present without compromising the ability of future generations to meet their own needs.   There are glowing accounts of industries engaging and collaborating with the communities within which they are based. In amongst these are also some disasters which result from cultural assumptions, industry created dependencies and the failure to attain community buy-in despite significant investment by the industry involved.   There are also remarkable stories of communities, and action groups within communities, being a significant catalyst for positive change of their natural, cultural and social environment. In amongst these stories there are also accounts of long and drawn out battles; adversarial situations where no one wins; a litany of mistrust, tricks and tactics, with the better resourced party ultimately achieving its primary objectives at the cost of the other (and at the cost of any potential fruitful, mutual relationships).   So what makes the difference in achieving the positive rather than negative outcomes? The answer lies in the way the outcomes are achieved. Building relationships based on good communication, respect for divergent views, mutual understanding, and the development of trust and empathy, makes it possible to identify shared goals and objectives that best meet the needs of all parties.   Research indicates the mining industry is making good progress in developing policy and commitment to community development and engagement but that, ætranslating commitments into improved practices at the site level remains one of the industryÆs toughest challengesÆ. (Australian Government - Community Engagement and Development Handbook October 2006 @ page 49.)   This paper considers the merits of a process of community collaboration and what it has to offer in terms of meeting that challenge.

Jan 1, 2007

By Heinrich Majewski, Rob Jameson

"Careful review of site conditions and constraints is essential to select the appropriate shoring system for each project. Key evaluation criteria include the geotechnical profile, groundwater and environmental conditions, adjacent buildings and utilities, schedule and any project specific access or other constraints. Typical earth retention schemes range from rock or soil nail walls, through conventional anchored pile and lagging walls to deep internally braced cut-off systems. The Owner’s design team will often develop the conceptual approach under their design studies, and this is refined with Contractor input through Design-Build or Design-Bid-Build procurement. In downtown San Francisco, underground construction must accommodate a unique combination of variable fill, soil, rock and groundwater conditions, potential for severe seismic loadings, and constrained sites within a dense urban environment. The quarter square mile of San Francisco’s Transbay and Rincon Hill districts has seen repeated cycles of development, destruction and re-building through earthquakes and the economy, and has been intensely redeveloped over the last decade. Over 50 acres of this land has been reclaimed from the Bay since the Gold Rush and within 3 city blocks the bedrock slopes from over 250 FT depth below the fills up to outcrops over 100 FT above sea level. A series of project examples from within this small area illustrate how varied shoring systems have accommodated the highly variable subsurface conditions while offering best value in terms of cost, schedule and appropriate protection of adjacent facilities.INTRODUCTIONA walk of 3 blocks from Rincon Hill on San Francisco’s Harrison Street, north through the Transbay area to Mission Street will traverse an urban zone which has been reinvented twice within its 150 year history in response to major seismic events. This small area highlights the range of subsurface conditions and urban environments which are encountered and accommodated in shoring schemes throughout the city. This route down the north side of Rincon Hill overlies a steep bedrock slope, outcropping over 100 FT above sea level at its south end and dropping to over 250 FT below sea level at Mission Street. A complex overburden soil profile, shaped by seismic activity and changing sea-levels has created layered soils ranging from soft estuary muds, dense sandy strata and deep clay layers, in turn topped with urban fill, frequently contaminated with debris from the Great 1906 earthquake. This route runs parallel to, and 350 yards inland of, the San Francisco shoreline resulting in groundwater elevation close to sea level with almost limitless recharge within granular layers. On the higher slopes of Rincon Hill, groundwater is typically observed flowing on top of and periodically within the fractured bedrock formation. The Transbay and Rincon areas were developed early in the Gold Rush era of San Francisco. After destruction in the 1906 earthquake and fire, they became a transit gateway into the city throughout the 20th Century. Demolition of the Embarcadero Freeway in response to earthquake damage and social pressure has opened this large area to redevelopment within the last 20 years, creating a new commercial and residential hub for the city. In its latest wave of building, planners are developing taller structures with deeper basements, in turn creating new construction challenges. Selection of shoring systems appropriate for these developments requires detailed evaluation. The process must address both the rapid spatial changes in subsurface conditions and the constraints surrounding, and specific to, each site in order to define shoring performance requirements. This paper presents an overview of the subsurface conditions and land use development of the Transbay and Rincon Hill areas, with examples of the shoring systems selected to meet site-specific conditions and requirements. The projects cited range from soil nail wall"

Jan 1, 2017

By N. P. Kripakov

The Bureau of Mines has developed a unique new mine design procedure to determine the changing static load distributions imposed on under-ground support structures during the mining cycle. The procedure reduces the complexities associated with analyzing a three-dimensional problem. A combination of the multiple-seam displacement-discontinuity model and a two-dimensional finite-element window model produces refined results for a specific area of interest by assuming displacement compat-ibility between models. Input to the procedure includes the geometry of mined-out areas in up to two adjacent seams, the rock mass characteris-tics of the surrounding geology, the in situ stress conditions, and the mining sequence. The displacement-discontinuity program calculates ex-pected loadings for mine structures affected by the mining cycle and/or by overlying or underlying seams. Pseudoelastic finite-element analysis using a yield-factor approach determines the stability of coal pillars by simulating the degree and extent of nrogressive rib failure and sub-sequent load transfer. Application of the procedure is demonstrated on a field problem. In-duced stress changes predicted from the numerical model analysis are in reasonably good agreement with stress measurements obtained from an instrumented chain pillar affected by remnant workings in an upper seam.

Jan 1, 1988

By Stephan I. Zajac, Roger A. Blais, John B. Stubbins

THE iron deposits of central Labrador occur within a relatively small area, herein called the Knob Lake Iron Range, in which a northwest-trending series of low hills and ridges defines the height-of-land at the boundary between provinces of Quebec and Newfound-land. Approximately two-thirds of the deposits are in Quebec and the remainder in Labrador, with several deposits straddling the inter-provincial boundary. These deposits are being exploited in open-pit mines by the Iron Ore Company of Canada centered at Schefferville, Quebec. Since 1954 this company has produced more than 56 million tons of iron ore to become Canada's leading iron ore producer. With indicated reserves of more than 375 million tons of direct-shipping ore and large tonnages of iron formation amenable to beneficiation, this mining district is assured of a long life. This paper describes the Knob Lake iron ores and their geological settings and stresses the features that lead to a better understanding of their origin. The

Jan 1, 1961

By Victor Azbe

Introduction Lime enters our daily life in many ways. Our building, chemical, agricultural, sanitary, and industrial endeavours depend on it to such a great extent that it could probably be called the most important inorganic chemical, and the extent to which it is used might be considered an index of industrial development. Industrial limes vary greatly in quality, due to internal structure and other characteristics. They may be good or bad, sensitive or slow to react. While improper manufacture may not greatly alter the appearance of the lime, it may affect its properties considerably and thus its suitability in the many processes in which lime is used. In some of the processes, one kind of lime is wanted, in others another. While the nature of the stone from which it is made has much to do with whether a lime is suitable or not, its burning and hydration are the crux of the matter. Up to not so many years ago, the knowledge of lime burning was rather imperfect and it is only relatively recently that its manufacture is approaching the state of a higher industrial art. This slow development was in part due to lime manufacture being scattered among many small concerns who, independently, either lacked the inclination or could not afford to strive for a higher technical development.

Jan 1, 1946

By E. J. Gleim

[THE ORGANIC act under which Federal Bureau of Mines was established provided for the investigation of the safe use of electricity in mines. Each Congress appropriates funds for conducting this investigation. As part of this investigation, electrical apparatus used in mines is studied to determine if its operation and use might introduce a hazard. From this study, certain safety standards have been developed. These standards, established with the aid of both the manufacturer and user of such apparatus, are published in schedules, and apparatus that complies with the requirements set forth these schedules is classified as "permissible." This term is defined to designate apparatus as "completely assembled and conforming in every respect with the design formally approved by the Bureau of Mines." In the judgment of the Bureau, the manufacturers of such apparatus have adhered to certain minimum standards of safety in supplying a product that when properly used and maintained is safe for operation in mines where flammable gas or coal dust may accumulate. This work of the Bureau of Mines for increasing safety does not make it obligatory for manufacturers of mine equipment to produce only that of permissible classification. Before the effective date of the Federal Mine Safety Code,5 the Bureau sought to promote safety by recommending that mine operators install permissible equipment in gassy mines as a preventive measure against gas and dust explosions initiated by electrical equipment. For some years, the mining laws of several States have prescribed the conditions under which permissible equipment must be used. The Federal Mine Safety Code requires that ?all new electric face equipment and replacements of equipment purchased for mines where nonpermissible equipment is now being used shall be of a permissible type approved by the United States Bureau of Mines,]

Jan 1, 1955

By F. W. Gray

Summarized Foreword This paper is one of a series arranged by Institute Divisional Committees for the Fiftieth Anniversary Meeting, reviewing the experience of the major mining and metallurgical industries during the life of the Institute. The viewpoint is national and broadly technical. Geology is stressed on a continental scale without regard for provincial boundaries. The boundary between Canada and the United States is, however, so decisive a factor in our coal-mining economics and our political evolution that mention of its implications cannot be avoided. The Laurentian Shield in Canada makes the occurrence of coal deposits a geological impossibility between the St. Lawrence Lowlands and the Great Plains. All but five per cent of Canadian coal resources occur west of Winnipeg. The utilization of this ninety-five per cent of our coal wealth has to date been a consequence of transcontinental railways' development, and the small fuel needs of thinly populated wheat farming and cattle-raising territory, in what- to judge from the development of mixed farming and greater population density of Manitoba- is merely an initial stage of agricultural intensification and accordant population growth. There is no useful purpose in measuring coal resource against consumption rate in the West as a whole, because the resource is but partially known, and it is difficult to believe that industrialism based upon coal utilization is in any but its infant stage of growth. Canada west of Winnipeg possesses, moreover resources of petroleum and natural gas, which, together with the power-potential in the long watershed of the eastern slope of the Rocky mountains, give to population centres such as Calgary and Edmonton a choice of energy resources that is almost an embarrass des riches.

Jan 1, 1948

By E. M. Timoshenko, A. V. Tarasov

The results of laboratory, bench-scale and semi-commercial investigations of a method for adding surfactant (technical-grade lignosulphonate) to the process of pressure leaching of nickel-containing pyrrhotite concentrates have been discussed. Lt has been demonstrated that feeding of technical-grade lignosulphonate distributed along the length of an autoclave ensures a reduction in its requirement by a factor of 1.5 to 2 as compared with single-point feeding; it also results in a decrease by 5% in the unit requirement of metallized iron-bearing precipitator in the process of non-ferrous metals precipitation and reduces by 0.05 to 0.1% (abs.) the nickel and copper contents in the tailings of the given process. Technical solutions have been proposed for commercial introduction of the process.

Jan 1, 2004

By Alan E. Gallie

One of the requirements for the successful waging of war is an unlimited supply of iron ore. In the spring of 1941 the demand for iron ore was expected to exceed the supply. This was particularly so in the case of high-grade lump iron ore, essential to the open-hearth process of making steel. The bulk of Canada's iron ore was imported from the United States. At this time, Canada was making every effort to conserve United States funds for more vital purchases. For these reasons, the development of Canadian iron ore resources became of prime importance. Several companies undertook investigations and one of these examined the old Josephine deposit. Location The Josephine property is in the district of Algoma, in the Michipicoten area of the Sault Ste. Marie mining division of Ontario. It is 120 miles north of Sault Ste. Marie and 20 rail-miles east of Michipicoten harbour, on lake Superior (see Figure 1). Transportation in the area is furnished by the Algoma Central and Hudson Bay railway. The Michipicoten branch of this line passes within a mile of the Josephine mine. Michipicoten harbour provides a port through which iron ore is currently shipped. Power in the area is supplied by the Great Lakes Power Company, with generating plants on Michipicoten river, on Montreal river, and on St. Mary's river at Sault Ste. Marie. A series of transmission lines cover the district and one of these is connected to the Josephine mine by a 3 ½-mile branch line. History The Josephine property was staked by Alois Goetz in 1899. Before the claims could be recorded, the township in which they are located was given to the Algoma Central & Hudson Bay railway as part of a land grant. As a result, the ownership remained in dispute until August 24th, 1906, when a settlement was arbitrated by the Honourable Frank Cochrane. His ruling is interesting and is quoted in part.

Jan 1, 1947

By John B. Knaebel

This paper is one of a series being prepared by the Bureau of Mines on mining methods and costs at various mines in the United States, Canada, and Mexico, and is a description of practice at the Edwards mine of the St. Joseph Lead Co. ACKNOWLEDGMENTS The cooperation and assistance of the officials of the St. Joseph Lead Co. in permitting publication of this paper and providing every facility for its preparation are gratefully acknowledged. Especial thanks are extended R. J. Mechin, manager, R. F. Mitchell, mine captain, and J. S. Brown, geologist, for their generous aid, and the assistance of W. H, Weijola, mine engineer in assembling some of the illustrations is deeply appreciated, The helpful suggestions of C. F. Jackson, principal mining engineer, U. S. Bureau of Mines, are gratefully acknowledged.

Jan 1, 1932

By R. J. Kuczynski

The U.S. Bureau of Mines Reno Research Center investigated, developed, and patented a high-temperature cyanide leaching process for recovering platinum-group metals (PGM) from automobile catalysts. A batch pilot plant was constructed at the center and operated to demonstrate this technology to industry. Approximately 1,600 kg of used pellet, monolith, and metal support catalysts containing 1,700 g (54 tr oz) of PGM was processed. Forty-five-kilogram batches of used catalysts were leached with sodium cyanide solution at 160°C for 1 h in a countercurrent processing sequence. This selectively dissolved the PGM. Average extractions from the used pellet catalyst were 96 pet Pt, 95 pct Pd, and 73 pct Rh. Average extractions from the used monolith catalyst were 84 pct Pt, 81 pct Pd, and 66 pet Rh. Heating the pregnant leach solutions to 275°C for 4 h destroyed the PGM-cyanide complexes, causing over 99.7 pct of the PGM to precipitate from solution. The PGM precipitate was predominantly a metallic powder concentrate, typically analyzing greater than 50 pct PGM. Heating destroyed the cyanide to less than 0.2 mg/L free and total cyanide. Both the pellet and monolith residues were evaluated for disposal using the toxicity characteristic leaching procedure developed by the U.S. Environmental Protection Agency.

Jan 1, 2010

By Roger L. Beals, George A. Tweedy

I. INTRODUCTION. THE results of the cyanide-operations, given in detail in the following paper, show the progress that is being made at the Minas del Tajo. The old pan-amalgamation process, in operation up to and including 1905, while paying a profit on high-grade ores, was no longer able to treat profitably the ores in sight at that time, hence an alteration in the process was imperative. The success of this alteration is eloquently expressed by the following data Pan- Amalgamation. Cyanidation. 1905. 1907. 1903. Tons treated, . . 51,387 53,983 69,300 Value per ton (U. S. currency),. $10.75 $8.39 $8.28 Extraction, per cent., 65.00 88.50 S7.45 Extraction, per ton. .- $7.00 $7.4.; $7.24 Total cost, per ton treated, 6.50 4.311 4.01 Profit, per ton treated, . . 0.50 3.07 3.23.;

Feb 1, 1910