Search Documents

By W. L. Price

The intelligent selection of wire cloth and perforated plate for screening surfaces seems a rather confusing subject to the newcomer in aggregate processing. The proper application of various screening surfaces is a complicated one and one could consider himself an expert only after many years of working with all applications. However, part of the subject matter could be simplified considerably for, the average screen user. In this paper an attempt will be made to do this, by presenting some comparative specification data along with cost figures Unfortunately, it is impossible in the limited scope of this paper to give actual service comparison records between different cloths or cloth and plate. Anyone who has considered making actual service comparisons for competing screening media is well aware of the almost insurmountable problems Their solution would form the basis for a separate paper on that subject alone. Therefore, this paper will be limited to comparative data up to the point of installation.

Jan 1, 1961

By M. A. Evanto

Since the late 1970's, the Roof Control Division (RCD) of MSHA's Technical Support has been performing linear analyses for the enhancement of miners' safety. This remote sensing process uses Landsat data to predict areas of potentially hazardous ground conditions in underground mines. To date approximately 700 analyses have been completed by the RCD, with nearly 75 being performed with the current equipment, software and methodology which was updated in early 1995. While success is difficult to measure, requests for linear analyses continue to come from large and small mining companies which suggests the industry's acceptance of the process.

Jan 1, 1998

By T Raynlyn, R J. Holmes, J R. Manuel, A Poliakov, L Lu

The prediction of sintering performance of iron ore fines and the possibility of targeted optimisation of specific sinter properties are very important for both the iron ore industry and related research organisations. Physical pilot-scale sinter runs require large amounts of raw materials and are expensive, so it is critical to target large test work programs with many different sintering parameters effectively. To predict values for sintering performance parameters such as tumble index (TI), low temperature reduction disintegration index (RDI) and productivity, a comprehensive database of pilot-scale sintering experimental results has been established and empirical modeling conducted. Similarly to earlier work, physical, chemical and mineralogical characteristics of the iron ores have been considered. However, in contrast to the previous work where only one textural parameter was taken into account, namely the proportion of dense haematite ore texture, the current model includes the abundances of several different textures which were combined into different textural factors corresponding to different sinter properties. Coefficients for the variables within specific regression equations can provide a better understanding of the effect of the variables on the corresponding sintering performance. The modelling results have also been used for predicting the sintering performance of mixtures that were not part of the database used for establishing the models. Comparison of experimental and modeling results for the verification test data is also reported in this paper.

Jan 1, 2009

By H. Hamza

Efficient and effective management of extraction process tailings is an essential ingredient for the continued success and development of Alberta's vast oil sands resources. Open-pit oil sands operations north of Fort McMurray recover bitumen from flotation circuits. Process tailings are managed in carefully engineered and monitored external tailings management facilities and in below-grade mine pits. In order to support reduction of production costs and improve upon established tailings management practices, CANMET has been working with the oil sands industry in a collaborative framework to assess the potential to integrate thickened tailings into oil sands extraction process flowsheets. Albian Sands has commercialized the process while others, including Syncrude Canada Ltd., continue to evaluate the suitability of the process for their operations. This paper provides an update on R&D work undertaken in recent years to assess and develop the potential of thickened tailings technology for the open-pit oil sands operators of northern Alberta. The aim of this work was to explore opportunities to optimize process efficiency and environmental sustainability by improving water and energy conservation and develop more alternatives for tailings management and reclamation.

Jan 1, 2004

By A Vakili, F Harvey, H Greaves

Mine seismicity is one of the most difficult geotechnical risks to manage in seismically active mines. There are currently some established empirical and statistical methods that provide quantitative measures for seismic hazard assessment in operating mines. However, these methods are mostly suitable for quantifying the current or historical seismic hazard and often cannot be directly used to forecast the future hazards. Numerical modelling is the only analytical tool that can capture the level of complexities required for a meaningful analysis of mine seismicity and therefore to facilitate a reliable forecast of future hazards. However, there is currently no widely accepted and established guideline and methodology for analysing and forecasting mine seismicity using numerical modelling. This paper first provides a background on previous published studies on this subject and then outlines the key aspects that can affect the reliability of the forecasting for mine seismicity. These aspects include a) processing of historical seismic data, b) selection of suitable numerical modelling approach, c) Post-processing and interpretation of the model outputs. A case study is then presented for the Gwalia Deeps Mine where a new framework was developed to forecast future mine seismicity. High-quality seismic data for a period of five years was used for back-analysis and comparisons with the numerical modelling outputs. After development of the method, the future seismicity was forecast for the next 12 months and the actual seismicity was monitored against the forecast during this period. Results of this study shows promising potential for the proposed framework to be applied more routinely and at other mine sites. However, more validations are required at Gwalia Deeps mine as the mine proceeds to deeper levels. In addition, the method needs more improvements and should be tested and validated at other mining operations before it can be established as a proven method. CITATION:Vakili, A, Harvey, F and Greaves, H, 2018. Forecasting mine seismicity – towards a more established methodology, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 207–222 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By A. Hajati

The main purpose of this study was to find the optimum values for factors affecting the Zn recovery rate using oxine or dithizone as a chelating agent collector during flotation in a Hallimond tube. Eight control factors, including four levels of pH, oxine/dithizone, corn starch, sodium thiosulfate, sodium citrate, sodium silicate, conditioning and floating durations were considered in a Taguchi experimental design technique. An L32 orthogonal array was applied to determine the signal-to-noise (S/N) ratio. Analysis of variance (ANOVA) was used to determine the optimum conditions and the most significant parameters affecting the reaction rate. Analysis of the experiments using the Taguchi approach indicated that pH had the highest contribution to the recovery rate of zinc oxide particles. The results showed that the recovery rate of zinc increased by 43.4 ± 3.0% and 24.9 ± 3.2% using oxine and dithizone, respectively, under optimum conditions with a confidence level of 90%.

Jan 1, 2010

By B. Mishra

Several reactive metal purification processes using molten salts generate effluent from which significant quantities of metal can be recovered prior to discardinglrecycling the salt. A Salt-scrub [SS] process has been applied where the reactive metals are recovered as a metal-gallium alloy by calciothermic reduction of the metal compounds. The SS alloy compositions were produced by mixing, pressing and sintering the metal-powders. Measurement of metal recovery has been studied for cerium, silver, tin and lead. The process has been optimized for variables such as the metal quantity per kg of effluent salt, amount of excess calcium over stoichiometry, stirring rate and time and holding time at reduction temperature. Over ninety-seven percent metal recovery has been obtained under optimized conditions. The development of an alloy for efficient Salt Scrub processing reduces a major contaminated waste disposal problem as well as recovering the valuable reactive metal. Surrogate metals have been used in this work to study the behavior of plutonium.

Jan 1, 1994

By L. C. IlsLey

Cooperation between the United States Bureau of Mines and the Safety in Mines Research Board of Great Britain, continuous since 1924, has made possible this and other papers on safety subjects. Grateful acknowledgment is made to representatives of the Board for their assistance in arranging visits to several mine safety stations, and to F. R. Wynne, Deputy Chief Inspector of Mines, for arranging visits to mines in Great Britain and other countries in Europe. During the summer of 1927 the writer had the privilege of visiting the mine safety testing stations in great Britain, Belgium, Germany, and France, in the order named. All of these countries have large coal mines, many of which are rated as gassy. Therefore, when the installation of electrical equipment is contemplated, each of these countries is confronted with the same safety problem as is the United States - the development of electrical equipment that will not ignite gassy atmospheres which through neglect or accident might surround the equipment. The means employed by these countries in safeguarding gassy mines should therefore be of general interest to safety engineers in American coal mines, and it is proposed to give a brief survey for each of the four countries mentioned. The third of these surveys covers conditions in Germany.

Jan 1, 1929

By D L. Reid, G Nwaila, J Petersen, J-P Franzidis, Y Ghorbani, M Becker, F C. de Beer, L C. Bam

Traditional methods of gold extraction have involved comminution and processing via cyanide leaching, all of which are associated with energy, cost and environmental implications. Subsequently, numerous opportunities for improvement and optimisation strategies in gold mining and processing have been explored, including heap leaching, which has significantly lowered comminution costs. This paper explores the effect of the more energy efficient high-pressure grinding rolls (HPGR) on the comminution behaviour (especially on the crack density) and cyanide leaching performance of laboratory reactors study on run-of-mine gold ore comprising the Ventersdorp Contact Reef (VCR) and the Elsburg Reefs (ER), sourced from Carletonville in the Witwatersrand Basin in South Africa. The ore was comminuted using HPGR at three different pressure settings (120, 90 and 60 bar). Large (-16/+11.2 mm) and small (-5.6/+4 mm) particles of the HPGR product where then mineralogically characterised using optical microscopy, quantitative evaluation of minerals by scanning electron microscopy (QEMSCAN) and X-ray computer tomography (CT) before cyanidation. The results of the leach experiments indicated a correlation between gold extraction, particle size and crack density. Mineralogical characterisation of the ore indicates that the Fe-sulfides present in the VCR are likely to be more reactive than those in the ER, thus having a more favourable influence on gold cyanidation. Overall, the results show promise for the heap leaching of Witwatersrand gold ores prepared using HPGR and demonstrate the value of a multi-disciplinary geometallurgical approach.CITATION:Nwaila, G, Becker, M, Ghorbani, Y, Petersen, J, Reid, D L, Bam, L C, de Beer, F C and Franzidis, J-P, 2013. Morro do Ouro geological model with a metallurgical view, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 75-84 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

The Cadia Valley Operations currently hosts a large operational open pit, a large operational sublevel caving underground mine and two other underground projects at the study stage. This scenario creates an unusual situation for the evaluation and planning of a fifth major open pit project. The Cadia East Open Pit is a large gold-copper development located adjacent to the operational open pit and above one of the underground projects. A study team is conducting a comprehensive and robust analysis of the target orebody. Two key factors for this project include the existing and planned projects within the valley and the wide range of available mining methods. The aim for the study team is to present an optimal and practical case which suits the entire Cadia Valley Operation. A rigorous and robust analysis of the situation requires that each factor be properly evaluated. A modular system has been developed which allows the wide range of scenarios to be quickly and meaningfully considered. Sensitivities for each module drive the further development of that particular module. As each scenario progresses, an assessment is made evaluating its value, strategic value and practicality. In such a way, the number of scenarios is gradually reduced at each stage to produce a final short list of feasible cases. Each scenario on the shortlist is then assessed with regard to the existing operations and other projects. A qualitative and quantitative analysis is made. This ranking is used to provide the recommended case.

Jan 1, 2007

By J. F. Barkley

Two major problems in the operation of air preheaters for boilers are corrosion and the accumulation of deposits on the heating surfaces. Corrosion or loss of metal necessitates replacement of parts; the accumulation of deposits decreases the size of the gas and air passages, resulting in increased pressure drop for the same gas flow, and also affects the heat transfer. These items, either singly or together, limit the capacity and efficiency at which the equipment can be operated and affect its availability, even causing undesirable shutdowns under extreme conditions The field and laboratory work on regenerative air preheaters described in this report covers research on the relative corrosion resistance of different materials, such as various metals, special metal coverings, and fired clays, and studies on deposits, their nature, analyses, and corrosive effects. This is the first report on cooperative work of The Air Preheater Corp., of New York City, and the Federal Bureau of Mines.

Jan 1, 1953

By Phil W. Welch

At first glance, the similarity between the fine grinding of cement clinker and coarse grinding done in other mineral processing industries may seem remote. However, it is interesting to note that the mill discharge fineness of cement clinker is only 70 to 90% passing 100 mesh and quite comparable to other mineral processing grinds. There is however, a greater dependence of the mill on the air separator in the finish grinding of cement clinker than in other mineral processing industries which explains why a technique to guage the balance between a mill and separator first began in the cement industry. (1) More recently an adaptation of this technique has shown its application to the processing of phosphate rock and is the central topic of this paper. First, an explanation of work done with fine grinding cement circuits seems appropriate together with a few general comments regarding cement. When unground or partially ground cement clinker enters a finish grinding mill, it is subjected to mechanical forces of impact and attrition which gradually reduce it to a range of sizes characteristic of finish cement. That is, a range of approximately 1 to 125 microns. The large proportion of superfine particles relative to the coarse and intermediate size particles is typical of portland cement particle size distribution. It accounts for the workability characteristics of plastic concrete and the early strength development of concrete which is so necessary to its successful use as a construction material. For this reason It is quite evident from quality control tests when a shortage of superfines exists.

Jan 1, 1975

By R. Addison, T. Swendseid, R. Kehmeier, D. Larsen, J. Uhrie

"The development of a mining project necessarily progresses through many steps, beginning with the identification of a mineral resource and continuing through project construction. Several classifications of engineering study development are described, including preliminary economic assessment (PEA) or scoping studies, prefeasibility studies (PFS), feasibility studies (FS) and regulatory codes, each with a specific project organizational objective. This paper addresses the PEA, PFS and FS types of reports that are used by companies to evaluate projects, meet regulatory requirements and seek financing. The minimum requirements for engineering studies, focusing on the needs of financial institutions considering investment in a project, are outlined. IntroductionThe financing of mining projects in recent years has come under increased scrutiny by financial institutions owing primarily to an increasing percentage of projects whose capital expenditures had overrun project budgets or had failed to produce the economic returns anticipated during the project development process. Often, unfavorable project outcomes are not the result of widespread failures of the project engineering process but arise from inadequate engineering in limited specific areas of the project scope, such as overestimated mineral reserve, inadequate mine design, insufficient metallurgical testing or underestimated capital costs. Mill facilities and process infrastructure typically are responsible for up to 80 percent of the capital expenditures required by greenfield mining projects. They are often the project areas where capital costs are inadequately developed, and consequently are the areas highly scrutinized by financial institutions. This paper offers a perspective on the level of engineering expected by financial institutions as a prerequisite to committing support to developing mining projects.The evaluation of a mining project from exploration through development and production is a lengthy and complicated process. Mine development commitment activities for a potential project are initiated when a mineral resource is identified and continue through to the start of construction. The technical feasibility and the economic viability of each project are determined during the phases of mine development with more detailed engineering data required at each stage. There are at least four levels of engineering studies during development that are commonly acknowledged by the mining industry:"

Jan 1, 2016

By E. Adam, B. Milkereit, M. Salisbury, L. E. Reed, G. Perron

Integrating seismic reflection, borehole geophysical, and physical rock property studies is an effective means of mapping lithological contacts and structures in the crystalline crust. At Les Mines Selbaie in the northern volcanic zone of the Late Archean Abitibi Subprovince, a high-frequency seismic reflection profile has provided the first images of deep crustal structures of this important polymetallic mine site. Physical rock property and borehole geophysical studies confirm that prominent seismic reflections can be caused by lithological contacts, faults and sulphide mineralization. At Les Mines Selbaie, the first two of these are shown by this study. Clearly identifiable reflection images from sulphide mineralization have not been demonstrated in analysis of the profile. The seismic images provide useful information about gross structure in the vicinity of Les Mines Selbaie. They can also place important constraints on the sequence of tectonic events and, therefore, can aid future deep exploration programs.

Jan 1, 1997

By M G. Hawtin

The Rocklands copper project is a multilode, iron oxide copper gold (IOCG) + cobalt mineralised system located in the Eastern Fold Belt of the Mt Isa Inlier. Rocklands orebodies cover a range of oxidation zones from oxide, to supergene and primary. Each zone contains different economic minerals of interest. The supergene zones contain significant amounts of native copper and the primary zones are dominated by chalcopyrite. The juxtaposition of these oxidation zones and minerals make it an interesting mineralisation system.Current mine production sampling collects a nominal 3 kg drill chip sample from a 1 m composite, RC drilled interval. A site specific sampling procedure was needed to quantify introduced sampling error when taking grade control samples. Due to oxidation and mineralogical variation in ore zones we needed to develop a practically achievable sampling methodology that ensures minimum sample mass and sample error requirements are achieved to ensure ‘representative’ samples for all ore types.These issues are planned to be resolved using an experimentally derived method using principles from the Theory of Sampling. This method uses an experimental calibration of parameters K and a for Gy’s fundamental sampling error formula using a modified 32-piece sampling tree experiment to compile sampling nomograms for the primary and supergene ores. This paper demonstrates the process undertaken to improve the quality and standard of existing mine production sampling procedures at the Rocklands operation.Results indicate a sample mass of 5 kg for RC drill chips is appropriate for both the primary and supergene ores to achieve a fundamental error below 0.01 or 10 per cent relative error, which is slightly higher than the existing sampling protocol of 3 kg. An additional experiment is recommended to compile sampling nomograms using the exact laboratory comminution and mass reduction stage information to assess the use of a 3 kg sample. The results also indicate no changes are required to existing sampling protocols when sampling RC drill chips in primary and supergene ore at Rocklands.Sampling nomogram results also provide a useful ‘rule of thumb’ reference guide to other mining and exploration companies to help understand minimum sample mass requirements and sampling error during exploration drilling, resource evaluation and mining production stages when targeting similar IOCG mineralised systems. A sample mass of 5 kg is recommended when RC drilling similarly IOCG mineralised prospects and deposits in the Cloncurry area. Future test work is recommended when additional open cuts become active as well as including resource drilling drill core to provide better three-dimensional sample representivity.CITATION:Hawtin, M G, 2017. Minimum sample mass from reverse circulation grade control drilling at Rocklands copper project, in Proceedings Tenth International Mining Geology Conference 2017, pp 337–346 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By W. Dingley, G. R. Hoey

"Thirteen Canadian sulphide ore mines were surveyed for corrosion control. The mines visited were a small, yet representative, proportion of this segment of the Canadian mining and metallurgical industry. Information on metallic corrosion and methods used to control it in underground workings and mills was gathered (a) by discussing corrosion problems with company personnel, (b) by examining equipment and structures during under-ground and mill tours, (c) by photographing corrosion sites, and (d) by collecting and analyzing mine water samples.The corrosion survey, which is summarized in the re-port, leads to the following general conclusions. Mine environments are corrosive, particularly when the mine w1a-ter is acidic. Because of a lack of good corrosion control measures, excessive deterioration of equipment due to corrosion occurs in mines. Mill environments are also corrosive, but in some cases good preventive measures are being taken to effectively control corrosion losses.Ways to reduce corrosion losses in sulphide ore mines and mills are discussed. The main areas for more corrosion research and development are selection of materials of construction, protective coatings, cathodic protection, inhibitors, equipment design, and mining and milling practices."

Jan 1, 1971

By F. S. Thurner

"This paper describes the engineering and construction activities of the ""design-build"" project awarded to the joint venture of Foundation-Comstock-Janin for the construction of the plant and wharf facilities, camp site, power plant and all supporting services. As a member of the Foundation Group of companies at that time, Fenco actecl as consulting and design engineers for the project. Particular emphasis is given to the problems which adversely affected design and construction activities due to prevailing arctic conditions and the remote location of the project. The paper also describes the approach taken in the investigation of the site and soil conditions as well as the selection of the special structures for the 225,000-toncapacity fibre storage building, the wharf structure for 50,000-dwt vessels, and the 1,000-tph-capacity reclaiming and ship-loading facilities . It further covers the logistics problems and the scheduling activities related to the short duration of the shipping season, and the transportation of equipment and mate1•ials by sea as well as by air."

Jan 1, 1976

By S Robinson, R Perkins, D Barrett, D Kepert, C Fowers

The discovery and delineation of significant mineralisation in the Eliwana region continues Fortescue Metals Group’s strong exploration success. In the decade after the first hole was drilled into Christmas Creek in mid-2004 a total of over 11 Bt of hematite-goethite mineralisation have been delineated supporting the raising of $13 B, construction of five mines, 620 km of rail and a five-berth port. As of June 2014, Fortescue was shipping at the rate of 155 Mt/a. The area including the Eliwana and Flying Fish deposits is one of a number of future growth opportunities that Fortescue is currently evaluating.The Eliwana and Flying Fish deposits occur on the south dipping limb of the Brockman Syncline/Jeerinah Anticline. The Eliwana group of deposits are hosted by the Brockman Iron Formation with the Flying Fish/Broadway group hosted by the Marra Mamba Iron Formation.Structurally the area is dominated by moderate southerly dips of the regional dome and keel style folding. The regional limb is locally cross-cut at a small angle by asymmetric north facing Ophthalmian folds trending 110°. These fold sets, in part, preferentially host subsequent supergene mineralisation. Faulting is only locally apparent.Early phases of exploration commenced in 2006, with mapping of Flying Fish and reconnaissance drilling in 2007. However, due to the concurrent discovery (Clarke et al, 2009) and subsequent fast tracked development of Solomon channel iron deposit and Firetail bedded iron deposit (Simpson et al, 2011) priority was placed on developing Solomon due to its relative proximity to existing Fortescue infrastructure. Staged follow-up drilling of both Marra Mamba and Brockman targets at Eliwana was progressively undertaken from 2008 onward.As of 20 May 2014 a total of 1494 reverse circulation (RC) holes for 54 248 m and 13 diamond holes had been completed, resulting in the delineation of a Mineral Resource of 740 Mt. Exploration via mapping, drilling and metallurgical evaluation of adjacent prospects continues with additional resources expected in the future.CITATION:Barrett, D, Perkins, R, Kepert, D, Robinson, S and Fowers, C, 2015. Geological setting of Eliwana and Flying Fish deposits along the north limb of the Brockman Syncline, Hamersley Province, Western Australia, in Proceedings Iron Ore 2015, pp 219–228 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By R. Sellaro

It has long been understood that extended occupational exposures to respirable mine dusts can lead to chronic lung disease. In underground coal mines, coal workers pneumoconiosis (CWP) and silicosis are major concerns. While there have been many studies aimed at understanding total dust concentrations and silica content associated with different mining conditions (e.g., locations/occupations within a mine, cutting methods, geologic strata), little research has been completed to more comprehensively characterize respirable dust (i.e., by distributions of particle composition, size or shape). For such analysis, scanning electron microscopy with energy dispersive X-ray (SEM-EDX) may represent a powerful tool. This article is a preliminary investigation of SEM-EDX to characterize respirable dust from an underground coal mine in Central Appalachia. Samples were collected from various locations in the study mine, and individual dust particles were identified and classified by mineral type. A continuous personal dust monitor was also used to estimate respirable dust concentrations during sampling. This data was compared to particle densities observed under the SEM. Dust is generally defined as small, solid particles with an effective diameter between 1 and 100 µm. In underground coal mines, dust is produced by a variety of activities such as coal and rock cutting, materials handling, haulage and from a variety of materials. While the coal itself is primarily made up of organic carbon, it is estimated that as much as 60 percent of coal mine dust consists of mineral matter, including clays, metal oxides and sulfides, carbonates, quartz, phosphates and heavy minerals (WHO, 1997). Mineral matter may be ingrained in the coal seam or associated with adjacent or interlying strata, and may also be contributed by specific activities such as rock dusting. When dust is generated or made airborne, suspended particles tend to settle slowly with gravitational forces, but can remain airborne for extended periods of time depending on environmental conditions such as air velocity (Courtney et al., 1986) and particle properties such as size (ISO, 1995; WHO, 1999). Thus, miners working underground are routinely subject to occupational dust exposures ? with highly variable characteristics between and even within mines.

By R. Trueman, D. B. Tyler

Numerical modelling was used to determine the magnitude and direction of stresses around drives both adjacent to and distant from open stopes in the South Crofty tin mine. Modelling predicted that drives near the stopes are situated in a stress-relaxed zone. The peripheries of drives that are sited in solid rock away from the influence of stoping are in compression. Key-block modelling was used to determine the typical geometries of critical blocks and distinct element modelling was used to determine block stability. The conclusions derived from modelling fitted the observational data. This indicated that key-block theory is a valid tool for analysing the stability of roadways in the South Crofty mine. The support requirements for drives located next to stoped-out areas were formulated using a risk analysis approach to key-block formation. The results were compared with support guidelines derived using empirical design methods. Good agreement was obtained for the roofs of the drives but not for the sidewalls. The concept of a critical excavation width was formulated: once an excavation is larger than the critical size the length of rockbolts need not be increased as the excavtion dimensions increase. This may be the case in all rock mases.

Jan 4, 1993