Search Documents

By Brian R. Castle, James J. Scott

INTRODUCTION Referring to a ground support system as a 'band-aid' borders on getting cute, but the application of cable slings in U.S. mining is somewhat analogous. Where problems in the roof or rib require additional support, the versatile cable sling is the answer in a variety of conditions. To fully understand how and why cable slings are used today we must briefly review their development history. Much of the thrust over the last five to seven years in ground support fixtures has been the development of hybrid systems. Taking the best of two or more existing roof bolt fixtures and marrying them into a new fixture which exhibits the good characteristics without the bad of the parent systems. Resin point anchored mechanical bolts, continuous threaded rebar bolts, and others have all be- come important fixtures in rock mass stabilization. HYBRID GROUND SUPPORT SYSTEM The cable sling system is also a hybrid, both in its parentage and in its ground support characteristics. See figure 1. Cable slings combine the techniques of cement. grouting high-strength cables, Friction Rock Stabilizers, and truss-like suspension into a versatile and high- strength ground support system. 1/2" high-strength cable is cement grouted in place in a manner similar to pre-

Jan 1, 1983

By Patrick Granitzki, Alicia Plinio, Janitha Batagoda, Peter Howell

The City of Newark is making a comeback with new mixed-use multi-storied Residential Development projects. The majority of developers tend to use driven H-pile deep foundation systems to support their super-structures. A different approach was recommended for one particular new development near the Passaic River. The surficial geology included glacial deposits consisting of loose to dense sand overlaying relatively soft silt and clay and a lower stratum of medium-dense sand. During a preliminary site investigation for the project, bedrock was encountered at depths ranging between approximately 168 feet to 182 feet below the ground surface. Design capacity required a single pile of 200 tons. Two different pile foundation systems were evaluated in conjunction to the typical driven H-pile system in order to review potential costs and construction schedule impacts. The two alternative pile systems evaluated were tapered tube piles and drilled displacement piles. Theoretical calculations were followed by in-situ load testing. The field testing results indicated the use of drilled displacement piles as the best option for a portion of the proposed building. This paper discusses the different piles systems considered, installation and using drilled displacement piles to minimize cost and optimize construction.

Sep 8, 2021

By Ljubisa Obradovic, Baisui Han, Batnasan Altansukh, Zoran Stevanovic, Atsushi Shibayama, Jonovic Radojka, Daizo Ishiyama, Kazutoshi Hag, Radmila Markovic, Ljiljana Avramovic

This paper discussed a combined froth flotation and high pressure leaching (HPL) process to recover copper from mine tailings. At first, froth flotation were carried out using the mine tailings sample under various conditions in the presence of different pH (3.5-10) and sulfurizing reagent value (0-1000 g/t), respectively. As a result, optimum condition (sulfurizing reagent of 1000 g/t, pH of 10, PAX (collector) of 100 g/t and MIBC (frother) of 200 g/t) was found for froth flotation of copper. The effects of sulphuric acid concentration, leaching temperature, total pressure (steam pressure plus oxygen pressure) on high pressure leaching (HPL) of mine tailing were investigated using sulphuric acid solution in the presence of oxygen. The best conditions for HPL were obtained to be sulphuric acid concentration: 0 mol/L (water), leaching temperature: 170 ?, total pressure: 2 MPa, leaching time: 1 hr and pulp density: 100 g/L. The leaching rate of copper reached nearly 99 % and the concentration of copper in pregnant leach solution (PLS) was 0.24 g/L. Finally, copper in the mine tailing was recovered using froth flotation followed by HPL. As a result of a combined froth flotation and HPL, the vast majority of copper (99 %) from the mine tailings was extracted.

Jan 1, 2014

Gold rooms represent a high security area and preventing theft is a challenging task. Where gravity concentrates or high value unit intermediate products are present, particular and specific security procedures must be put in place. This paper describes the development and implementation which reflects best practice in gold room security. Procedures involving key holder systems, key locks, swipe cards and double locks preventing any one person having access to the gold room, including specific procedures for gravity gold concentrators, will be addressed. The use of monitoring and how to deal with alarms and potential hold ups will be reviewed. The use of cameras and archival DVD recorders is common in gold rooms. The use of electronic surveillance, movement detectors, seismic monitors and the two person policy and gold room entry procedures are described, including how to deal with visitors. The importance of confidentiality regarding smelting and gold pick-up days, plus strategies employed to minimise storing large quantities of gold on site will be presented. The role of metallurgical accounting in providing quality auditable information and the minimum standards of record keeping required is discussed. The role of the Gold Squad will be outlined. Regular auditing and risk analysis and several case studies are cited where security was deficient or improved.

Aug 1, 2010

By Dirk Verhulst, V. I. Lakshmanan

Why Chloride Hydrometallurgy?The most available, cheapest and best known reagent for treating ores and other raw materials for the metallurgical industry is sulfuric acid. Hydrochloric acid is second in line. What often happens is that a process is developed on the basis of sulfuric acid, and that at some point the question arises: wouldn't hydrochloric acid do this better?Considering hydrochloric acid immediately opens a very interesting field of research. To summarize a few comments from another paper presented at this symposium [1]: chlorides are far more soluble than sulfates (with a few interesting exceptions); the hydrogen ion activity is greater in chloride than in comparable sulfate solutions; higher oxidative conditions are possible; regeneration is more straightforward; more diversity is possible and better conditions for the separation of species can be found for solvent extraction and ion exchange; sulfur in the ore can be separated as elemental S; higher metal concentrations in solution and more flexibility in the chosen oxidation state means significantly lower energy costs.Also, the volatility of many chlorides at higher temperature allows further separation without the need to go to a different system. Chlorides also form molten salts with a low melting point, providing another means of separation and purification in the same chloride medium.

Jan 1, 2011

By G. Reuben Yourt

THIS paper is chiefly a description of the improvements in dust control chat have been brought about in the assay office grinding room at Wright-Hargreaves. The fume exhaust systems are briefly included because they also are important to the health of the employees. There are three chief factors which determine the efficiency of a dust control system: First, the amount of time and thought spent in designing it. Second, how close! y it is kept up to date with the growth of the plant-a system that is adequate for the number of machines operating when it is installed may fall short of fulfilling its purpose as the plant expands. Third, unless someone is held directly responsible, a system is likely to get out of repair and gradually lose its efficiency-this can easily be detected by regular dust surveys. In designing the present system at Wright-Hargreaves, the object kept in mind was to reduce the dust concentration of all operations to a safe limit, chat is, well under 300 particles per cubic centimecer of air. By doing this, a condition would be attained chat would make it possible to discontinue the use of respirators, which at best are not very comfortable and do not remove all of the hazardous fine-dust particles.

Jan 1, 1941

By M. S. Hedley

"The Lucky Jim mine is at Zincton in Slocan mmmg division; on the Kaslo-Nakusp branch of the Canadian Pacific railway. It is owned and operated by Zincton Mines; Limited; a subsidiary of Sheep Creek Gold Mines; Limited. The mine is far in the lead in the production of zinc in the Slocan. Its recorded production from concentrates and shipping ore was 102; 260; 191 pounds of zinc to the end of 1945.GENERAL GEOLOGY With the exception of acidic dykes the rocks near the Lucky Jim mine belong to the Slocan series, which is Triassic in age and consists principally of argillaceous rocks. It disconformably overlies greenstones of the Triassic Kaslo series about 3 miles to the northeast, and is cut by granitic rocks of the Nelson batholith 5 miles to the southeast.The sedimentary rocks in this area are best referred to on the whole as slates. They lie within the more fissile basal part of the Slocan series. The term 'slate belt' conveniently distinguishes this area of rocks characterized by slaty cleavage from the more massive argillites that are more characteristic of the Slocan as a whole. The contact between the slaty and massive argillites lies ½ mile southwest of the mine."

Jan 1, 1954

By J. Sattarvand, P. C. Augustine

Despite significant safety improvements, the mining industry remains one of the most hazardous occupations globally and the evacuation of Miners, when an uncontrollable incident occurs in the mine, is the best bet to saving lives. However, Human factors/behaviors during an emergency are likely to influence the evacuation performance. Other industries have made a significant effort to determine these human factors that can impede evacuation performance, however, the current state-of-the-art in mine evacuation or self-rescue is that the evacuation route is predetermined, and a static sign is used to direct miners to the predetermined safe location. This method is limited in representing actual conditions that arise in a real emergency, neglecting the different behaviors displayed by humans. As optimization of the evacuation of a mine plays a fundamental role in emergencies and modeling evacuation behavior and movement of miners is a complex task, this research utilized Agent-Based simulations to simulate the evacuation behavior and performance. It was observed that people with the smart evacuation device made fewer mistakes and arrived at the safe place in less time compared to those have no access to the device. The Mathematical model used in optimizing the shortest path to a safe place is also explained in this paper.

Jun 25, 2023

By Jorge Alberto Soares Tenório, Denise Crocce Romano Espinosa, Beatriz Peralta Oruê

Manganese, a toxic mineral, related to manganism may have high added value for the steel industry. The difficulty in obtaining manganese encourages the exploration of new secondary sources such as the lateritic nickel effluent. In Brazil, nickel reserves are predominantly lateritic, making the country a potential producer. For the tests, a synthetic solution was used which simulates the lateritic nickel effluent from leaching. The oxidative precipitation with ozone occurred at the oxygen flow rates: 0.5; 1.0 and 2.5L/min, at the original pH 1.5 at 21°C in a 500 mL bubble column reactor. O3 was produced in the benchtop generator feed by 99% oxygen. The ozonation time was determined by the oxidation potential1.55V. The ozonated solution was centrifuged and filtered. The filtrate and collected samples were characterized in ICP-OES. Optimization tests with ultracentrifuge were performed. The best precipitation reached 97% at 0.5L/min O2 at 6.07 ± 0.045mg/min of O3 dosage and resulted in a solution 10-15mg/L Mn+2, above 1mg/L, maximum value acceptable by Conama 2011, to be retreated before being discharged into the water body or being reused as a manganese source.

Oct 3, 2019

By William Gleason

"Despite the difficult economic climate for the mining industry, more than 6,300 people joined SME for its 2016 Annual Conference & Expo in Phoenix, AZ, Feb. 21-24.Nearly every commodity has been bruised and battered during the past year, leading to one of the more difficult cycles for the industry in the past decade. Coal has taken some of the hardest hits and other commodities, such as copper and iron ore, have felt the sting of a slower growth in China and an oversupply on the market.The difficult conditions could not be ignored, but they did not deter SME from offering a forum for the industry to share knowledge, network with peers and learn about the best products and practices while visiting the sold-out exhibit hall (844 booths and 627 vendors) or while attending any of the 121 technical sessions that were offered.The current state of the industry was one of the overriding themes of the conference and during the challenging times there are often cutbacks as operations look to become leaner and more efficient, however, there is one area that cannot be cut – health and safety.The conference kicked off with a fascinating presentation from Colonel Mike Mullane, a former NASA astronaut who, in 1978, was selected as a Mission Specialist Astronaut in the first group of space shuttle astronauts. He completed three space missions and logged 356 hours in space aboard the shuttles Discovery and Atlantis before retiring from NASA and the U.S. Air Force in 1990.In his speech to a packed audience, he warned of the dangers of cutting corners to get the job done more quickly by guarding against the “normalization of deviance.”Normalization of deviance is a long-term phenomenon in which individuals or teams repeatedly accept a lower standard of performance until that lower standard becomes the norm. Usually, the acceptance of the lower standard occurs because the individual or team is under pressure (budget, schedule, etc.) and perceives it will be too difficult to adhere to the original higher standard. Their intention may be to revert back to the higher standard when this period of pressure passes. However, by getting away with the deviation from the higher standard, it is likely they will do the same thing when the same stressful circumstances arise again. Over time, the individual/team fails to see their actions as deviant."

Apr 1, 2016

By Douglas Glenn Stalheim

The demands for improved mechanical properties in hot rolled long products are increasing as the expectations of global Standards and construction designer’s increase. Cost constraints limit the excessive use of expensive alloys to meet these expectations. In addition, depending on the mill, equipment can limit what can be realized to meet the increasing expectations. The most effective way to meet the increasing expectations for improved mechanical properties of optimum strength and ductility is through producing steel with as fine as possible uniform cross sectional grain size in the “as-rolled” condition. The best solution to the development of this fine and uniform cross sectional grain size is to develop a cost effective alloy design coupled with proper metallurgical process control implemented into an existing mill’s equipment capability and layout. In other words, properly bringing together alloy, metallurgy, process control and existing equipment capabilities to develop an optimum product that can meet the increasing demands of the construction designer. This paper is designed to give a solid understanding of the production and metallurgical requirements to achieve a grain size in “as-rolled” long products that is as fine as possible within the limitations of the process and production parameters of the individual plant.

Jul 30, 2018

By G. de Tomi, G. C. Teodoro, E. Rodovalho, T. M. El Hajj, J. A. S. Tenório

The selection of an underground mining method stems from a multivariate analysis that considers geomechanical, geological, economic, and operational parameters. Even after identifying the most compatible method, there is no assurance that the mining company will achieve the best performance. The geological complexity of some deposits requires adaptations of methods described in the literature to obtain more selectivity and reduce mining waste. There are some studies on geometry of underground structures, but a methodology that describes an adaptation of a room-and-pillar mining method for ore bodies with down-dip varying from 20° to 25° is novel. The present work aimed to reduce dilution by adapting the traditional room-and-pillar mining method (TRP) to inclined ore bodies. This new method is entitled short-hole room-and-pillar (SHRP). The equations that measure the dilution are defined according to the geometry of stopes and openings. The results comprise comparative analyses of the operational and planned dilutions to measure the performance of the SHRP method. The average operating dilution of the SHRP method was more than five times lower than the planned dilution according to the TRP method. Low operational dilution indicates high selectivity of the method and its potential to reduce underground mining tailings.

Sep 9, 2024

By Sukumar Bandopadhyay

The Marine Minerals Technology Center (MMTC) was authorized by an act of the United States Congress in 1996. The act established several marine minerals research centers in the U.S., including one at the University of Alaska Fairbanks. The Alaska MMTC is funded through the Minerals Management Service of the Department of the Interior and concentrates its research in the Arctic seas region. Recent research projects at the MMTC include, among others, application of a geographic information system (GIS) to the gold placer deposits offshore Nome, Alaska, development of a marine gold placer reserve definition model using a neural network, and development of an expert system model for submarine tailings disposal (STD) planning and decision-making. Although geostatistics remains the most prevalent method used today for ore grade estimation, researchers have made numerous improvements over the years for accurately predicting grades of ore using other estimation techniques. One such technique, the neural network, has recently emerged as an alternative to geostatistics for grade estimation purposes. A neural network is a non-linear, model-free estimator that is well-suited for noisy and/or sparse data environments. Neural networks perform best with non-linear spatial data, contrary to the stationary assumption of ordinary Kriging techniques. In the marine placer ore reserve definition model, the neural network technique was used to estimate placer gold reserves offshore Nome. This study demonstrated the utility of neural network modeling over other traditional ore reserve estimation methods, especially for high cut-off grades. Some of the relevant issues of neural network modeling were also addressed in the study. In testing, the neural network produced results that were close to those from geostatistical techniques including Kriging, polygonal, and inverse distance methods.

Jan 1, 2005

By S. Fiore, M. C. Zanetti, C. Clerici

The processes and fluxes of a cast iron foundry plant located in the North of Italy were analyzed in order to determine the amount and kind of wastes produced from the different activities. The main fractions are the molding sands, furnace muds and powders coming from the dust abatement plant, the exhaust lime, the furnace refractory, the metallic shotting and the sludges and powders coming from the dust abatement plant of molding lines for a total production equal to 800 t/d. All wastes were sampled and particle-size and chemically characterized to evaluate the best recycling or reuse solutions. Wastes were sieved and divided in three categories according to the particle-size dimensions: below 0.1 mm, between 0.1 and 0.6 mm and above 0.6 mm. The fraction above 0.6 mm dimension underwent magnetic separation to recover and quantify the potentially available iron fraction. The fraction between 0.1 mm and 0.6 mm was chemically characterized in order to understand if it could be fed to the sand regeneration plant. The below 0.1 mm fraction was characterized to evaluate the following recycling and reuse solutions: additive for molding sands and/or raw material for the concrete industry.

Jan 1, 2003

By Qinghua Tian, Zhipeng Xu, Dong Li, Xueyi Guo, Liu Zhu

A possible process for extracting tellurium and antimony from a residue generated in alkaline sulfide leaching of telluriumbearing alkaline skimming slag was proposed. The central composite design was employed to define the optimal leaching conditions for tellurium and antimony extractions from the residue sample. Using a 23 factorial matrix, the best performance for tellurium and antimony extractions (96.36% and 99.64%) were obtained at 175 g L−1 Na2S concentration for 80 °C during 60 min. The notable degree for influencing tellurium and antimony extractions was leaching temperature, Na2S concentration, and leaching time. The analysis of variance results indicated that the regression model was significant and suitable to be used for the optimization of independent variables within the range. The model was validated under optimal operating conditions based on the experimental design results. Antimony and tellurium in the leach liquor were separated and recovered by H2O2 oxidation followed by Na2S-Na2SO3 reduction. 98.93% of antimony was precipitated selectively during H2O2 oxidation, while 95.06% of tellurium was precipitated during Na2S-Na2SO3 reduction. NaSb(OH)6 and elemental tellurium was obtained as the product.

By A. Cecala, J. Noll, J. Organiscak

Many underground metal/nonmetal mines are using enclosed cabs on mining equipment to reduce the exposure of miners to diesel particulate matter (DPM). However, some enclosed cab systems may not be meeting their expected efficiency in capturing DPM, which could be a result of inappropriate filter use, cab leaks or insufficient pressurization. NIOSH investigated several types of filters for reducing DPM to determine which type had the best capture efficiency. The laboratory results indicated that a MERV 8 (minimum efficiency reporting value, as defined by the American Society of Heating, Refrigerating and Air- Conditioning Engineers) filter captured about 50% of the DPM, a MERV 16 filter collected 96-98% of the DPM and two HEPA (high efficiency particulate air) grade filters captured over 99% of the DPM. NIOSH also performed a field study to measure the efficiency of two cabs at a limestone mine. The cab filtration systems of a loader and haul truck were found to be over 90% effective in removing DPM, except under certain operating conditions when the efficiency was as low as 41%. A possible reason for the low efficiencies is an open window in the cab, but more studies need performed to obtain a better understanding of the cause and solution of the problem.

Jan 1, 2011

By W. W. Anderson, D. G. Girton

The photoluminescence of Pr, Nd, Ho, Er, Tm, and Yb in CdS, and Ho, Er, Tm, and Yb in ZnSe has been observed from crystals Prepared by diffusion using rare earth metals and an excess chalcogen pressure. For a given temperature, time, and chalcogen pressure the spectral characteristics were very reproducible from run to run, and the emission intensity for Nd, Er, and Yb in CdS was as high or higher than the best vapor phase doped crystals we have grown. For a few rare earths it was found that certain conditions of diffusion tend to yield optimum rare earth emission intensity with respect to the background lattice emission. Photoluminescence measwements of Yb in CdS as a function of depth gave a profile which was neither a Gaussian nor complementary error function. Part of the profile appears to arise from a fast component of the diffusion and the other part from a slow diffusing component. At 960°C and 33 atm S pressure, a com -plimentary error function approximation of the slow diffusing component gave a diffusion coefficient of D = 1.3 x 10-9 sq cm per sec. MOST of the studies of emission from rare earth ions in II-VI compounds have been reported on crystals doped during growth,1,2 although Kingsley and Aven prepared ZnSe:Er by diffusion for paramagnetic resonance and fluorescence studies. Pappalardo and Dietz prepared CdS:Yb by diffusion, but they made optical absorption measurements., We know of no study on the properties of rare earth diffusion in the II-VI compounds. To date we have diffused Pr, Nd, Ho, Er, Tm, and Yb into CdS, and Ho, Er, Tm, and Yb into ZnSe and observed the rare earth emission spectra. For a given temperature and chalcogen pressure, the emission characteristics are very reproducible from run to run and for Yb, Nd, and Er in CdS, as good as the best crystals we had prepared by doping during vapor phase growth.2 The emission of Pr, Ho, and Tm has been observed in CdS prepared by diffusion for the first time. Previous attempts2 to prepare these later three materials by vapor phase growth were unsuccessful. The problem of obtaining reproducible characteristics in II-VI semiconductor compound work is well known.5 Not only is it difficult to reproduce results from one laboratory to another but it is sometimes difficult to reproduce results from one growth run to another under ostensibly identical conditions within one laboratory. This situation has been particularly bothersome in research on the luminescence of rare earth activated ZnS1 and Cds2. Crystals from one vapor phase growth run would show very strong rare earth line emission while crystals from a nearly identical run would show no rare earth emission. It was also observed on occasion that the intensity of the rare earth emission was not constant over the entire volume of a single crystal. MATERIAL PREPARATION AND INSTRUMENTATION Vapor phase grown boules of CdS were supplied by Dow Corning. This material was characterized by a free electron concentration of n - 3.5 x 1015 cm-3 and Hall mobility of 350 sq cm per v sec at room temperature. There were microscopic voids and decorated precipitates in some samples. The precipitates annealed out at diffusion temperatures but the voids remained. Single crystal rectangular samples of mm dimensions were sawed from the boules. The ZnSe was polycrystalline, UHP grade from Eagle-Picher. Poly-crystalline samples were sawed from the ingots. The samples were lapped, polished on one side, etched in a solution of 0.5 M K2Cr2O7 in 16 N H2SO4, and thoroughly washed in distilled water. A sample, excess sulfur (or selenium), and 5 mg of rare earth metal (turnings) were sealed in a 3.6 cm3 quartz ampoule at about 2 X 10-5 torr. The high chalcogen pressure used (1 to 30 atm) prevented thermal etching of the crystals and affected the diffusivity and solubility of the rare earth ions in the crystal lattice. For meaningful or reproducible results, it is thus necessary to specify the vapor pressure at which the diffusion was carried out. It is assumed that a negligible amount of the chalcogen was used in the formation of rare earth sulfides or selenides Our sulfur vapor pressure calculations are based on data assuming S2, S6, and S, molecules only in which case the equilibrium constants are given by6 where the pressures are expressed in torr. Selenium vapor consists of a mixture of Se2, Se4, Se6, and Se6 molecules. The selenium vapor pressure was calculated using equilibrium constants given by The status of the rare earth source during diffusion is unknown, i.e., the partial pressures of the rare earth metal and of the rare earth chalcogenides has not been determined. All emission spectra were recorded at 77°K on a Perkin-Elmer model 98-G spectrometer using a 640 line per mm grating. No correction was made for the spectrometer and detector spectral sensitivity. Excitation was by means of an XBO 1600 w xenon arc

Jan 1, 1970

By K. P. Gupta, P. C. Panigrahy

The stabilization of the R, a-Mn, and 0-Mn phases have been studied in the Mn-Ti-Fe and Mn-Ti-Co systems. Iron and cobalt both appear to stabilize the (Mn-Ti) R phase to almost the sarne extent. The R-phase region was found to extend from the lowest e/a to slightly beyond the maximunz e/a limit known for this phase. But, while iron appears to stabilize the a-Mn phase, cobalt tends to stabilize the p-Mn phase. In the two systems manganese appears to get replaced by iron and cobalt in each of the mentioned phases. The instability of the a-Mn phase in the Mn-Ti-Co system and the /3 -Mn phase in the Mn-Ti-Fe system cannot be explained on the basis of adverse size effects because atomic diameters for both iron and cobalt (C.N. 12 at. diam) are ziery similnr and not much different from manganese which they replace. Qualitatively, the reason for the stability of the a-Mn and the p-Mn phases can be traced to the more favorable e/a ratio prevailing in the respective systems and to a competing tendency between the two phases. In transition metal alloy systems the o, p,P, R, a- Mn,' and p-Mn2 phases have been claimed as electron compounds. A large volume of work has been done to establish the criterion for the formation of the o phase but until very recently practically no systematic work was done on the a-Mn and the /3-Mn phases. A recent investigation on the P-Mn phase3 indicates the e/a criterion for p-Mn phase stabilization. Since the R phase was first known to appear only in certain ternary systems1 no detailed work was then possible for this phase. The R phase has been recently discovered as a binary intermetallic compound in the Mn-Ti~ and Mn-si~-' binary systems. The existence of binary R phases opens up the possibilities of studying the effect of alloying elements on the stabilization of the R phase. Of the two binary systems possessing an R phase, the Mn-Ti system appears to be more interesting because at a suitable high temperature it is possible to find the three electron compounds, the a-Mn, p-Mn, and R phases, side by side and it is possible to study the effect of a third transition element on these three electron compounds. For the present investigation iron and cobalt, so called B elements for the formation of electron compounds, have been used as the third element to study the stabilization of the a-Mn, P-Mn, and R phases. EXPERIMENTAL PROCEDURE The alloys were prepared by using 99.9 pct pure electrolytic Fe and Mn, 99.5 pct Co, and crystal bar titanium, supplied by Semi Elements Inc., New York and Gallard Schelsinger Mfg. Co., New York. Weighed amounts of the components were melted in recrystal-lized alumina crucibles in an inert atmosphere (argon) high-frequency induction melting unit. Titanium was made into fine chips for easy dissolution and a special charging procedure was adopted to avoid contacts of titanium chips with the alumina crucibles. Up to 20 at. pct Ti, the maximum titanium content in the investigated alloys, there was no visible sign of reaction of titanium with the alumina crucibles. With a careful control of melting time and temperature the losses were minimized and were always found to be below 0.1 pct. Because of such small and almost constant weight losses, the alloys were not finally analyzed. The alloys were wrapped in molybdenum foil and annealed in evacuated and sealed silica capsules at 1000" * 2°C for 72 hr and subsequently quenched in cold tap water. Annealed samples were examined metallographically and by X-ray diffraction. For all high manganese alloys oxalic acid solutions of various concentrations and 1.0 pct HN03 solution were found suitable as etching reagents. Best contrast between the a-Mn and the R phases could be obtained by using freshly prepared 60 pct glycerine + 20 pct HN03 + 20 pct HF solution. For high iron and cobalt containing alloys, especially for alloys containing the a-Fe, y-Fe, and P-Co phases, 15 cc HNOJ + 60 cc HC1 + 15 cc acetic acid + 15 cc water solution was found to be the best etching reagent. All X-ray diffraction work was carried out (using specimens prepared from annealed powders) with a 114.6 mm diam Debye-Scherrer camera using unfiltered FeK radiation at 25 kv and 10 ma. All calculations for X-ray diffraction work were carried out using an IBM 7044 digital computer RESULTS AND DISCUSSION The two ternary systems, MnTiFe and MnTiCo, were investigated near the manganese rich end, Figs. 1 and 2, and show some common features. In both alloy systems large extensions of narrow R phase regions occur at almost constant titanium contents. At titanium contents higher than that of the single phase R-phase alloys, the same unidentified X phase was found in both ternary systems. The extensions of the X phase close to the Mn-Ti binary indicate that this phase could be the TiMns phase. Too few X phase diffraction lines were present in the diffraction patterns to make positive identification of the X phase. In contrast to this similarity the two systems show opposite behavior in the extensions of the a-Mn and 8-Mn phase regions; while iron tends to stabilize the a-Mn phase, cobalt

Jan 1, 1970

By D. R. McMullin

The purpose of this paper is to provide a method for mine planners and engineers to evaluate on a conceptual basis if a shaft or a ramp is most suited for their particular underground access requirements. Mine planners and engineers are often raced with the decision of choosing which method of underground access is best suited for their particular requirement. Underground access can be provided by a shaft, ramp, adit, or slope for either exploration and/or actual production operations. This paper will focus on the construction cost and schedule differences between sinking a shaft and excavating a ramp which are currently the most typical access alternatives used in the western United States. It would be wrong to state that one method is superior to the other in every case. There are many variables to be addressed, and the degree of sensitivity of each of them will eventually dictate which method is the most suited to the particular circumstances. This paper compares the construction cost and schedule or sinking a shaft to excavating a ramp at different depths given different ground and hydrological conditions. This comparison provides mine planners with "rules or thumb" that may be applied to the access selection process.

Jan 1, 1994

By L. S. Sundae

The Bureau of Mines conducted a series of tests to compare the cutting forces required by radial and point-attack bits when making similar cuts. Three radial and four point-attack bits were tested in two coal mines using the Bureau's in-seam tester to measure coal-cutting forces in situ. Tests were also conducted to investigate the effects of weathering and cleating. The test results show that in each case, at a specific clearance angle, the radial bits required less tangential and much less normal force than the point-attack bits. The resultant of the cutting forces for some types of cut was 50 pct less at mine 1 for radial cuts compared to cuts with the best point-attack bit, and 40 pct less at mine 2. There was some difference between three types of radial bits, but it was not as significant as the difference between each type of point-attack bit. Cutting coal perpendicular to the cleat planes required less cutting and normal force than the same type of cuts parallel to the cleat planes. Test results showed no effect due to weathering on cutting force data. Cutting parallel increased forces only because cuts were made in the rock band.

Jan 1, 1987