Search Documents

By G. W. Elger

The Bureau of Mines investigated the conversion, at both laboratory and pilot plant scale, of a low-grade ilmenite to chlorination-grade feedstock that could substitute for imported rutile used to produce titanium tetrachloride. The concentrate was derived from the Tahawus, NY, lode deposit of ilmenite-magnetite in rock that contains anorthosite and gabbro. Charges of the ilmenite concentrate, containing 46.6 wt pct Ti02 blended with soda ash, were carbothermically reduced in an electric arc furnace, which separated most of the iron and left a high-titanium slag. However, the slag contained Ca, Mg, and Mn constituents that rendered the material unsuitable for continuous chlorination by causing plugging problems. After being ground and pelletized, the slag was reacted with S02 and air at 7000 to 9000 C, which selectively converted the harmful impurities to soluble compounds that were removed in a subsequent water or dilute HCI leach. In laboratory tests, the combined levels of harmful impurities were decreased from 5 to as low as 0.5 wt pct in leached slags. In pilot plant tests, leached slags sulfated at a rate of 10 lb/h averaged 85.5 wt pct Ti02 with pertinent impurity levels averaging 1.86 wt pct. The leached slag was successfully chlorinated in a laboratory fluidized-bed reactor at 9500 C to extract titanium as TiCI4.

Jan 1, 1986

By L. Schernikau, W. H. Smith

Oil, coal, and gas account for approximately 80% of global primary energy, but only a portion of total airborne CO2 eq (approx. 35% at GWP20 to 65% at GWP100), even though they account for 95% of total measured CO2 emissions. The benefits of these energy sources, as well as their related costs, are not all incorporated in current energy policy discussions. Global greenhouse gas policies must include documented changes in measured airborne CO2 eq to avoid spending large amounts of public funds on ineffective or sub-optimal policies. The authors examined airborne CO2, which is less than half of emitted CO2, as well as reported CH4 emissions and the global warming potential of CH4 as published by the IPCC for coal and natural gas. The surprising conclusion is that surfaced-mined coal appears ‘better for the climate’ than the average natural gas, and all coal appears beneficial over LNG. Therefore, current CO2-only reduction policies and CO2 taxes are leading to unintended consequences and the switch from coal to natural gas, especially LNG, will not have the desired impact of reducing predicted future global warming; in fact, quite the contrary. A large portion of anthropogenic global warming is attributed by the IPCC and IEA to CH4, but it must be noted that CH4 emissions from natural sources and from agriculture account for approximately 40% and 25% of annual global CH4 emissions respectively. Energy accounts for about 20% of documented CH4 emissions. CO2 contributes only approximately 35% of annual airborne anthropogenic GHG emissions after accounting for CH4, over a 20-year horizon. At a 100-year horizon, the contribution of CO2 increases to approximately 60%. Energy policies that do not consider all GHG emissions along the entire value chain will lead to undesired economic and environmental distortions. All carbon taxation and CO2 pricing schemes are incorrect and need to be revised. At IPCC’s GWP20 an approximately 2%1 higher loss of CH4 across the value chain prior to combustion of natural gas versus coal will lead to ‘climate parity’ of coal with natural gas. According to public data, natural gas value chains have high CH4 and undocumented CO2 losses. On a global average, using only IEA-documented CH4 data, natural gas emits approximately 15% more CO2 eq than surface-mined coal, over a 20-year horizon. This difference will increase as the use of shale gas and LNG expands. Investors should support all energy systems in a manner that avoids an energy crisis, including intermittent renewable energy systems where they make sense. If CO2 emissions need to be reduced, one of the most effective ways would be to install ultra-supercritical power plants with CCUS technology. However, the undisputed benefits of increased CO2 concentrations in the atmosphere because of its promotion of photosynthesis and plant growth effects (fertilization) need to be considered in energy policy decisions as well. The authors suggest that future research and development should concentrate on reducing net emissions from fossil fuel power plants and providing cost-effective and reliable new conventional power generation capacity, utilizing clean coal and clean natural gas technology.

Mar 2, 2022

By R. V. Higgins, H. C. Miller

"INTRODUCTION The development of methods for determining the total quantity of crude oil that a given pool could be expected to produce in the future and the well-spacing and drilling programs most likely to result in the recovery of the maximum quantity of oil at the minimum cost became problems of acute concern to American oil producers and petroleum engineers during the second decade of the twentieth century, The United States faced what seemed at that time to be a serious shortage of petroleum, and it appeared that the constantly increasing demand for petroleum and its products could not be adequately supplied. Undrilled prospective acreage, which until then had been plentiful, seemed to be getting scarcer, competition was increasing, the margin of profit to the producer was shrinking, and the need for developing constructive policies of conservation appeared paramount. As a result of physical and economic changes then taking place within the petroleum industry prompted by the seemingly uncertain future, accurate knowledge pertaining to the probable future production of oil wells and of oil lands especially was needed and greatly desired. Furthermore, the need for obtaining the maximum quantity of oil from known fields caused technical information - which up to that time had not been deemed essential to the successful and profitable operation of oil lands - to be sought eagerly. The need for technical information, such as methods for determining future reserves of oil and the rate at which the oil could be obtained under a specific program of drilling, was emphasized further with the passage of the Revenue Act of 1918, and oil producers with enough income to place them in the taxable class were compelled, for the first time, to report their taxable income 4/ to the Treasury Department."

Nov 1, 1939

By S. Mudau, P. Mohasoa, M. J. Cole

Derelict and ownerless (D&O) mines in South Africa have been an ongoing concern for over a decade. While some progress has been made to rehabilitate D&O asbestos sites, significant work remains, exacerbated by the growth in illegal mining. There are concerns regarding the accuracy and transparency of the D&O database, lack of oversight, and constrained funding, and the government is increasingly looking to the private sector to fund rehabilitation. Given these challenges, a new, sustainable approach to D&O sites in South Africa is needed to bring clarity and transparency to the process, recognise responsibilities and promote partnerships, and explore economic opportunities at D&O sites to reduce the financial liability and respond to the growing demand for critical minerals. This article has three components: i) reviews of international D&O good practices; ii) it analyses South Africa’s current approach and the D&O sites; and iii) proposes a D&O framework that addresses data, risk ratings, responsibilities and rehabilitation, economic opportunities, and stakeholder engagement. The study finds that the majority of the 6,100 so-called abandoned D&O mines are quarries and mine site features, 16% are operational, at least 11% have owners, and only 752 (12%) require rehabilitation. The framework aims to bring clarity and fairness to decision-making and to assign risk and responsibility for rehabilitation and seeks to incorporate economic opportunities to reduce the financial burden of rehabilitation, create jobs for local communities, and respond to the growing demand for critical minerals for the clean energy transition.

Apr 25, 2025

By Hooman Askari-Nasab, AHLAM MAREMI, EUGENE BEN-AWUAH

In oil sands mining, tailings are voluminous unwanted by-products generated from extracting the desired mineral from the mined ore. Dyke construction and backfilling activities require well-managed techniques to facilitate progressive reclamation at the earliest opportunity. This directly affects the sustainability and profitability of the mining operation. This research introduces a goal programming framework that simultaneously optimizes the (1) production schedule with limited duration stockpiling and directional mining; (2) dyke construction schedule; (3) size, shape, and location of tailings-cells; and (4) mining and processing production targets. The results show that in creating in-pit tailings-cells designs, decreasing the mining-cells volume and increasing the number of mining-cells improve the net present value of the operation due to increased operational flexibility. The model generated a uniform schedule for ore and practical tailings-cells designs for backfilling activities. Integrating tailingscells optimization into oil sands mine planning and waste management ensures the efficient use of in-pit mined-out areas required for sustainable operations.

Apr 14, 2021

By Irina Chernyshova, Erik Larsen, Hanumantha Rao Kota, Vladislav Slabov, Garima Jain

The separation of fine mineral particles, especially using environmentally friendly approaches, is one of the main problems in the processing of low-grade ores and the re-processing of mining tailings. This work assesses the potential of biosurfactants as collectors in the flotation of ultrafine (smaller than 20 μm) particles of hematite and malachite. As biosurfactants, we test acetylated acidic (ac-ASL) and lactonic sophorolipids (ac-LSL). In addition, n-dodecyl-β-D-maltoside (DDM) is used as a model non-ionic alkyl disaccharide surfactant, and sodium oleate (NaOl) is used as a reference. The biosurfactants are characterized using surface tension and foam analysis. The interaction of the minerals with the surfactants is characterized using zeta potential, solubility, and single-mineral flotation. The collecting properties of the surfactants are compared for the ultrafine (− 20 μm) and coarser (38–90 μm) particle size in the two-mineral flotation of hematite and malachite against quartz. The ultrafine particle size improves the grade in the oleate flotation of hematite, as well as the grades in the DDM flotation of hematite and malachite, which is explained by the weak interactions of the metal oxides with fatty acids and DDM. At the same time, the flotation with ac-LSL and ac-ASL is highly tolerant to the ultrafine particle size. These results indicate that biosurfactants are an interesting alternative to conventional petroleum-based surfactants in the flotation of Fe and Cu oxides. Moreover, a proper selection of surfactants can help combat the problem of fines.

Feb 23, 2023

The Editor, with the full realization of his own forgetfulness of political duties until it is brought to his attention perhaps by some unfavorable election already. consummated, wishes to remind the thinking men who compose the body of the membership of this Institute that never before in the history of the country has it been so important that we should be represented at Washington, and in our State Legislatures, by men of vision, high character, courage, broad experience in the more important affairs of life, and undoubted loyalty. Let us all endeavor to secure the nomination and election of this type of man, and let us, each in his own district (which collectively will represent practically every important locality in the Union) carefully scrutinize all candidates for election and work for the-best one who seems to have any chance of being. successful. Let its place ourselves in communication with political leaders, newspaper men of prominence, and public men generally, strengthening our own appreciation of the importance of the election at this time and cooperating for the purpose of obtaining candidates of the highest character. Upon the men of intellect depends chiefly the burden of wise selections at this time. Congressional elections will occur this Fall in the following states:

Jan 8, 1918

By A. Singh, R. R. Maclachlan

SYNOPSIS A back-analysis procedure based upon 35 mm photography was developed on a laboratory scale for the pur¬pose of determining the percentage of oversize particles known to be present in heaps of fragmented rock. Eight simple blends of crushed stone containing varying percentages of oversize on a 1:40 modelled scale were examined. Simulated test conditions for the following were subjected to the photographic study: (1) a bench heap, (2) the surface exposure of a partially excavated heap, (3) a gravity-sorted surface as occurs on an apron dump, and (4) four quadrant views of an incrementally built conical heap of rock fragments. The best back-analysis determinations were obtained from (4), the cone, over all eight blends of fragments. The mean error was within -0,16 per cent of the true value, with a range of ± 1,872. This was for oversize contents of 5 to 20 per cent where a minimum 25 per cent of the photograph area was processed by digitizer. The worst results were from the apron dump at - 1,462 per cent for a mean error of ± 4,174 per cent. The intermediate results were from the undisturbed bench at -0,186 per cent with a mean error of ±2,862 per cent.

Jan 1, 1989

By U. Martin

Advanced copper materials for conducting applications require an optimal combination of high mechanical strength at ambient and moderately elevated temperatures together with superior electrical and thermal conductivity. Mechanical alloying under repeated cooling of the milling vials in liquid nitrogen has been applied to produce ultra-fine grained (UFG) oxide dispersion strengthened (ODS) copper with a high yield strength at ambient temperature. In the present study ODS copper was manufactured by mechanical alloying of copper powder and 3% by volume of incoherent oxide dispersoids. During the high-energy milling a homogeneous distribution of fine dispersoid particles (diameter nearly 100 nm) can be achieved in the powder. Samples with a density of more then 97% of theoretical value were produced by uniaxial hot pressing under 650 MPa at 600°C for 20 minutes. The high yield strength at ambient temperature can be described by a linear superposition of the Orowan stress for particle hardening and of ultra-fine grain strengthening according to the Hall-Petch mechanism. Simultaneously, a best value of 75% IACS could be obtained for the electrical conductivity. The creep behaviour of ODS copper in the temperature range from 500°C to 700°C is described within the frame of diffusional creep deformation.

Jan 1, 2007

By A. C. Atenas

The majority of refineries that operate with traditional starting sheet technology ?starting sheet- uses a relatively low current density of 250 A/m2. Industrial tests at high current density with conventional technology were carried out in Refinery of Potrerillos, getting satisfactory results that are similar the results obtained with permanent cathode technology. The series of copper refining electrolyses electrolysis trials were carried out between 300 to 325 A/m2. Electrolysis conditions, in accordance with industrial practice, were kept constant in all sets of experiments and were as follows; 45 g/L Cu 2+, 210 g/L H2SO4, 62 °C, electrolyte circulation of 14-18 L/min. The same Dosing dosing of Additives additives used in permanent cathode technology was required in these tests. In general, only not importantminor operational modifications were necessary in comparison to normal practice in the Refinery to assure the good results. Different quality of starting sheet and anodes were examined. The test included starting sheets from smelter and laminated process. Results indicate that the charge physical quality of the electrodes and the control of the process during the two first days of operation are the keys to get the best results.

Jan 1, 2007

By Kirk Yeager

All explosive formulations display some sensitivity to heat. A common technique utilized to measure an explosive’s response to thermal stimulation is differential scanning calorimetry (DSC). As DSC analysis is run on quantities of material easily handled in a laboratory setting, and is relatively inexpensive, it tends to be one of the more predominant tools utilized to determine potential thermal hazards of energetic materials. The analysis of energetic materials via DSC provides unique challenges, as both large energy outputs and significant production of gaseous products result from their decompositions. In addition, the unique thermal decomposition characteristics of ammonium nitrate (AN) based materials have also created difficulties in DSC analyses. A wide variety of techniques have been developed to study the decomposition of explosives. Traditionally, sealed glass capillaries were utilized to house samples. Recently, the introduction of specialty cells designed to withstand high pressures has enabled new sampling techniques to be developed. Analyses of explosives with both traditional and “high-pressure” cells will be compared and contrasted. Lessons learned about the application of both techniques towards analyzing thermal hazards such as incompatibilities will be presented. Inconsistencies in the results displayed during analyses of AN-based explosives will be highlighted. Recommendations on the best approach for analyzing the more problematic AN formulations will be given.

Jan 1, 2000

By Manouchehr Oliazadeh

Talc is used as a gelating, diluting, antimould and softening agent in the pharmaceutical industries. This article reviews efforts made for producing pharmaceutical grade talc from a mine located in the west of Iran, called Masoud Abad. Reaching to the pharmaceutical standards, was the principal goal of the talc beneficiation. Methods such as flotation and leaching were applied to eliminate the impurities. Considering to the negligible Fe content of the ore, the major impurity was calcium carbonate and to some extent dolomite. Depressants used in froth flotation were dextrine, quebraco and sodium silicate. Variation of collectors such as oil petroleum, paraffin, stearic acid were also used. After optimization of the effective parameters, followed by two stages of flotation (rougher and cleaner) acid leaching process was also applied as a complementary step to remove the impurities. CaO impurities in the sample was 11.63% which reduced to 1.03% after two stages of flotation, and finally reached to 0.03% CaO by leaching process. This figure is more lower than the world pharmaceutical standards (i.e. <0.6 % CaO). The highest recovery was 55% at the best conditions. Other impurities (i.e.As, lead, heavy metals ,?) which were at standard levels, confirmed by the authorized health organizations.

May 1, 2001

By G. Brofas

The reforestation potential of bauxite mining spoils by seeding was examined on this research work. The experimental plot was established on the location Strofi Koukouvista 5, Ghiona Mountain. The experiment consists of 3 species (Pinus nigra, Robinia pseudoacacia, and Spartium junceum) with 4 sowing treatments and 2 sowing seasons (autumn and spring). The treatments were: (1) broadcasting; (2) broadcasting and soil cultivation; (3) broadcasting with straw mulching and straw binding with asphalt emulsion; (4) broadcasting with soil cultivation, straw mulching and straw binding with asphalt emulsion. Third year results show that spring is better than autumn as a sowing season. Only the Spartium junceum species were found to germinate and survive in autumn. The results are better for all the species on the spring seeding. The most effective treatments for Robinia pseudoacacia and Pinus nigra are 3 and 4 while for the Spartium junceum even simple broadcasting shows good results although the best ones are achieved with treatments 2, 3 and 4. The paper?s findings show that reforestation by sowing could be effective for some species but further experimentation with other species is recommended. Concerning Robinia pseudoacacia, testing of different seed preparation treatments is needed in order to maximize the germination of seeds.

Jan 1, 2002

By J. J. Bodmer

Although the similarity between puzzolana, or trass, and blastfurnace slag, as seen by comparison of the analyses, is a well-known fact, blast-furnace slag has not been used commercially as a substitute for those cementing materials. The reason, the writer apprehends, lies in the fact that unless such slag is disintegrated or subdivided by rolls, the process must either be too costly, or the material is not in a fit and proper condition for the purpose. In order to produce a reliable slag cement, the slag must be ground together with the lime into an impalpable powder. The subdivided slag must, therefore, be perfectly dry, and, at the same time, friable. The stronger the hydraulic properties of the lime, the more reliable the slag cement will be, and practice has proved, that the slag from a gray-iron furnace gives the best results. The slag cement which has given the results shown in the annexed table, under pressure tests, was composed of six parts of slag, from a blast-furnace producing No. 3 foundry iron, and one part of lime, of medium hydraulic properties. The above-described class of cement bears storing as long as most Portland cements, and the cheapness of its production is self-evident.

By J. J. Bodmer

ALTHOUGH the similarity between puzzolana, or trass, and blast-furnace slag, as seen by comparison of the analyses, is a well-known fact, blast-furnace slag has not been used commercially as a substitute for those cementing materials. The reason, the writer apprehends, lies in the fact that unless such slag is disintegrated or subdivided by rolls, the process must either be too costly, or the material is not in a fit and proper condition for the purpose. In order to produce a reliable slag cement, the slag must be ground together with the lime into an impalpable powder. The subdivided slag must, therefore, be perfectly dry, and, at the same time, friable. The stronger the hydraulic properties of the lime, the more reliable the slag cement will be, and practice has proved, that the slag from a gray-iron furnace gives the best results. The slag cement which has given the results shown in the annexed table, under pressure tests, was composed of six parts of slag, from a blast-furnace producing No. 3 foundry iron, and one part of lime, of medium hydraulic properties. The above-described class of cement bears storing as long as most Portland cements, and the cheapness of its production is self-evident.

Jan 1, 1874

By Hugh R. Wilson

Echo Bay&apos;s Waste Management Program for its Lupin Mine was developed in response to the terms and conditions of the water license issued to the mine in 1981 by the Northwest Territories Water Board. The gold mine, located about 80 km (50 miles) south of the Arctic Circle, commenced production in 1982. The Waste Management Program was based originally on the total containment concept, contingent on future treatability testwork results indicating the best treatment method to ensure pond discharges would be in compliance with stated Northwest Territories Water Board discharge criteria. To assess the various treatment technologies, an investigative program was established to determine the most effective means for treating the tailings pond water. In the course of milling, about 850,000 m3 (11 million cu yd) of tailings are produced annually that require appropriate management to protect the environment. This annual tailings stream consists of about 175,000 m3 (229,000 cu yd) of solids and 675,000 m3 (883,500 cu yd) of water. Following the completion of the required waste management studies, a two-ponds-in-series concept of tailings impoundment was developed. To attain this concept, the tailings impoundment area would require modification and construction to enable the use of such a system.

Jan 1, 1991

Korea has about 68 hundreds million tons of limestone&apos;s reserves. Still, high-Ca2+ limestone containing more than 52% calcium oxide makes up for about 12% only; hence the need for securing and effectively developing limestone. The best solution is to manufacture precipitated calcium carbonate (PCC). The synthesis of PCC using high-Ca2+ limestone has several advantages including the efficient development of resources and easing the import dependence on PCC. The first step is the selection of suitable limestone for the synthesis of PCC. In this study, formation age was decided as the primary key point, with its effect on calcination, hydration, and synthesis of aragonite investigated. Results showed that the yield of aragonite increased when newer limestone was used. On the other hand, neither the activity and bulk density of quicklime nor the particle size of aragonite was affected by the formation age, although special values were registered following each formation age. Moreover, the bulk density of quicklime and particle size of aragonite tended to increase with decreasing activity. This result is different from that of the other experiment. Therefore, a suitable method for measuring the activity of quicklime for use in the manufacture of PCC must be established.

Jan 1, 2006

POSITIONS VACANT (Under this heading will be published notes sent to the Secretary of the Institute by members or other persons.) Superintendent for iron mine operated on the sub-level and caving system. Small output, moderate salary. Location, Southern State. No. 45. Chemist to sample and analyze iron ore. Experience in other branches not essential. Location, Southern State. No. 46. ENGINEERS AVAILABLE (Under this heading will be published notes sent to the Secretary of the Institute by members or other persons introducd by members.) Experienced mine superintendent desires position. Several years&apos; experience in practical management of mining and development work. Has also practiced ass consulting engineer and is thoroughly experienced in the examination and development of mining properties. Mexican experience. Will go anywhere for reliable concern. Salary moderate. References. No. 254. Member, mechanical superintendent, wants position. Has had 12 years&apos; experience as master mechanic of smelting plants in United States and Mexico. Also superintendent of shops doing marine, mining, and general contracting work. . Experienced in manufacture of mining tools and equipment. Up to the minute in copper, lead, and zinc smelting. Has learned a learned a great deal, can forget much, and has the inclination and ability to learn more. Best of references. No. 255.

Jan 10, 1915

By G. Viramontes-Gamboa

Approximately 70% of world copper reserves consist of the mineral chalcopyrite, and much international effort has focused on its study. Ultimate objectives include the development of environmentally friendly alternatives to smelting, and technologies to treat low-grade ores, for which concentration and smelting are economically unviable. Unfortunately, chalcopyrite leaching is inefficient in H2S04-Fe2(S04)3-FeS04 solutions, which is considered to be the most desirable oxidizing medium for leaching of copper sulfides, since the chemistry is well known, corrosion of industrial equipment is negligible, subsequent copper recovery by SXlEW is well established, and environmental impact is minimal. The main reason for this inefficiency is the self-passivation of chalcopyrite. We have devoted considerable effort in the understanding of this phenomenon, and have developed a predictive electrochemical methodology capable of establishing a priori the precise range of potentials within which chalcopyrite leaches and where it is passivated. Since potential control is a critical parameter in chalcopyrite leaching, this experimental methodology can be very useful for establishing the best conditions to leach chalcopyrite. In this paper, the scientific foundations of this predictive experimental technique are presented, and its practical application is demonstrated by comparing its predictions with leaching experiments from the literature.

Jan 1, 2007

By Frank C. Greene

Drilling for oil and gas in Missouri continued at a slightly lower rate than has been prevailing. A summary of operations for the past few years as compiled and published by the Missouri Geological Survey and Water Resources is as follows: Two oil pools are being developed in Cass County. Neither area has been drilled completely, and detailed descriptions will not be given at this time. In the Endicott pool in the southern part of T. 44 N., R. 33 W., oil is found in the Warrensburg sand, which is now considered to be the Big Lake sand of eastern Kansas. The top of the sand is about 125 ft. below the Herthalimestone. The best well is reported to have made 14 bbl. per day for the first four days. The oil is 30" to 32&apos; BB. gravity. This is the only pool in the state, aside from the older areas on the east and west edges of Lees Summit, Jackson County, that is producing oil from the Warrensburg sand. Drilling continues in the Knoche pool in the central part of T. 46 N., R. 33 W., where the oil is found in the Squirrel sand. The oil produced by both these pools is sold by truck in Kansas City.

Jan 1, 1937