Search Documents

By Matti Kongas, Kari Saloheimo, Antti Remes

"The paper studies the control performance of the flotation process as a function of the measurement accuracy and sampling frequency of an on-stream XRF analyzer, using a simple dynamic model. An additional aim is to assess how the economical result of a mineral flotation process depends on the quality of process control based on the on-line elemental assays.An on-stream XRF analyzer measures the concentrations of slurry lines in a continuous cycle from several process points. The control performance depends on the analytical accuracy and sampling frequency of the concentration measurement. With a long cycle time, the state of the process changes before a new measurement becomes available. With short measurement times the statistical variance of the counted X-ray pulses increases, increasing the random error in the analysis. In addition, the measurement accuracy depends on the concentration of the component to be measured from the slurry.To quantify the effect of analysis error and frequency to process control, a simple dynamic process model is created in the Matlab environment. Data from a copper flotation circuit is used as a test case. The process model comprises a first order reaction equation and the grade-recovery -relationship estimated from process data. The control was modeled using the control strategies implemented into a rule based advanced control system.The economical performance of the control was studied by calculating the overall net smelter return at various analyzer parameter combinations. The economical performance of the process declines strongly when the sampling cycle is increased. In studied case the sample measurement time did not have a significant effect on the results. The economical performance of the simulated process corresponds to an almost uncontrolled process when sampling cycles longer than 40 min are applied."

Jan 1, 2003

Since it was first introduced, the Coal Mine Roof Rating (CMRR) has been widely accepted as a tool for geologic characterization and mine planning. This paper discusses the application of the CMRR to another practical ground control problem. Extended cuts (cuts greater than 6 m (20 ft) in length) are commonly used with remote control continuous miners. Extended cuts can greatly increase productivity, but they have been associated with a number of fatal roof fall accidents. When extended cuts are attempted in weak roof, the roof may collapse before it can be bolted, causing hazardous conditions. Until now, it has not been possible to predict where conditions may not be suitable for extended cuts. In this study, data on the CMRR and extended cut experience were collected at 36 mines in 7 states. It was found that when the CMRR was greater than 55, deep cuts were routine in nearly every case. When the CMRR was less than 37, extended cuts were almost never taken. Between 38 and 55, extended cuts were feasible sometimes but not others. The data also shows that extended cuts are less likely to be stable if either the entry span or the depth of cover increases.

Jan 1, 1998

By W. Sharkey Bowers

This study was undertaken in order to determine a conservative estimate of the attenuation rate of vibrations through the shallow limestone in South Florida due to quarry blasting.

Feb 1, 2020

By AIME AIME

A. A. Holland, Consulting Engineer, Toronto, Ont.-I noticed in this discussion of locations in which radium is found, no mention is made of the recent deposits discovered in Ontario. While radium is not a subject with which I am very familiar, I took an interest in this deposit on account of its novel occurrence. It is found in Haliburton County, near Wilberforce, Ontario, associated with a quartz free pegmatite, in a "break" that I understand can be traced for two miles. This "break" marks the contact between the limestone and syenite and contains numerous cavities or vugs. The gangue, on account of its deep purple, appears to :be amethyst.

Jan 1, 1930

By W. M. Ross

AMONG the comparatively few A radical changes in mining equipment in recent years is the introduction and use to an ever greater degree of detachable bits for rock drills. Just how great the possible field for economic application of this innovation is, and to what ex- tent detachable bits are used instead of the conventional type of drill steel, are matters of conjecture. Just as a rough approximation, one might conceive that at least three-quarters of the drilling done in mines today could better be performed by steel with detachable bits, instead of only about one-quarter as at present.

Jan 1, 1939

By R. Sibley, K. Perry, E. McCorkle, M. Coy

Black powder has been used in fireworks since the 10 th century in China. To this day, black powder still has a variety of uses, including fireworks, and remains relatively unchanged. Black powder is used in the firework shell to help produce the effect and in the lift charge to propel the shell skyward. The performance of fireworks shells used in displays varies greatly. In fireworks shells, there are two different black powder charges that differ in construction based on the desired performance of the shell. The two charges consist of the lift charge and the break charge. The lift charge is the first to fire and propels the shell out of the mortar. The break charge is the second to fire and is initiated after a delay from the lift charge; its purpose is to burst the shells effect over the desired area of the sky. The lift charge provides the shell with its initial velocity by pressurizing the mortar below the shell body. The pressurization process is violent and occurs in fractions of a second. The purpose of these experiments are to better understand the pressures sustained in fireworks mortars during the firing process. Mortars and shells vary by size and weight. Pressures in each mortar were monitored at various heights along the mortar to provide a pressure profile during shell lift. A high-speed camera was used to measure shell exit velocity near the mortar’s muzzle. This information was correlated with the size and weight of shells and their respective lift charges

Jan 1, 2024

By John Owens, Hamid Maleki

Efficient and safe use of mobile roof supports (MRS) depends on the interaction between the MRS and coal strata. Of particular interest to this study are the mechanics of strata deformation as influenced by geologic conditions, pillar extraction methods, and MRS load-bearing capabilities. To provide a better understanding of the mechanics of strata deformation, the authors have collected and reviewed measurements of convergence and stress in one western U.S. mine and have completed pseudo-three-dimensional, boundary-element modeling for two typical pillar-pulling plans. Stress distribution in the mine roof above pairs of MRS’s was calculated to demonstrate how MRS’s contributed to the control of roof block movements. It was shown that overall stress and roof-floor convergence patterns were most influenced by the stiffness of coal-measure rocks and by pillar-pulling sequences and layouts. MRS’s and other support systems play a critical role in controlling the stability of both the immediate roof and the middle roof for a distance of up to 18 m (60ft) above the seam. MRS’s provide unique ground control advantages over other types of secondary support by significantly reducing the time between mining and installation of secondary support. Although MRS’s are similar to posts in stiffness and capacity, they are more effective than posts under static loads because they can yield and still maintain loads at near-peak capacity, whereas posts fail and loose their ability to limit mine roof deformation.

By A. N. Clay, N. N. Moeketsi, S. Joubert

For many years, mine-impacted water has been regarded as a problem and linked to long-term environmental liabilities. However, this water can be a renewable and a sustainable resource, provided that it is managed in a responsible and sensible manner. South Africa’s National Water Resource Strategy (NWRS, 2013) considers water that can be used to contribute to economic activity to be a water resource. Although all water resources are considered as belonging to the State, government does not appear to have meaningfully explored the use of mineimpacted water to contribute to the country’s economic activity. Africa is blessed with more sunshine than anywhere else, apart from Australia, yet we see no rollout of vast quantities of solar panels to ensure every African family has access to affordable power. This suggests that governments are incapable of managing such a free resource. At the same time, apart from the equatorial areas, water is a seriously constrained resource and yet we expect the same entities to manage a commodity none of us can live without. This paper explores the conversion of mine-impacted water from waste to a resource and how the inclusion of other stakeholders (such as water users, landowners, and ordinary South Africans) could benefit the process.

Jan 2, 2022

By Bruno Pinheiro da Silva

Controlar a distribuição de carga do Alto Forno é fundamental para o controle de processo, e através de sua otimização, dentre as mais variadas configurações operacionais, busca-se lograr da estabilidade do processo e aproveitamento do gás no interior do reator. Para tal, utiliza-se um sistema de carregamento, sendo o mais usado na atualidade o do tipo Bell Less Top com calha rotativa. Durante o carregamento do forno as partículas passam pela calha rotativa, resultando em abrasão dos elementos de desgaste que por sua vez, altera a geometria da mesma, gerando alterações na trajetória das partículas carregadas e a mudança de trajetória pode perturbar a marcha do Alto Forno. Nesse contexto, a boa condição da calha passa a ser um fator essencial para a manutenção da estabilidade operacional. O presente trabalho, aplica o método dos elementos discretos (DEM) para caracterizar os efeitos do desgaste da calha na trajetória do material descarregado, podendo assim avaliar melhor os distúrbios na estabilidade do Alto Forno, e com isso a indicar o melhor momento para troca da calha.

Oct 30, 2017

By Wei Yin, Bin Xu, Qian Li, Yongbin Yang, Tao Jiang

Copper anode slime is an increasingly significant resource for precious metals such as Au, Ag and Pd. The extraction of Au, Ag and Pd from decopperized anode slime by different pretreatments and different lixiviants including cyanide, chloride, thiourea and thiosulfate have been investigated. When oxidizing roasting pretreatment was carried out under the conditions of roasting time 120min and temperature 625 ℃, the removal ratios of S and Sb could reach 82.18% and 98.52%, respectively. And the following alkaline leaching of calcine could result in the dissolution of 46.40% Cu and 98.48% Pb. The optima leaching ratios of Au, Ag and Pd reached 99.48%, 97.69%, 94.79% by cyanide leaching, and 95.01%, 79.84%, 96.59% by chloride leaching, and about 95.21%, 95.66%, 48.79% by thiourea/thiosulfate leaching.

Jan 1, 2015

By Fabio Da Costa Garcia Filho

Durante os processos de beneficiamento de alumina, no processo Bayer, é gerado um resíduo insolúvel denominado lama vermelha. A incorporação de resíduos industriais em cerâmica vem sendo utilizada atualmente na busca de matérias-primas alternativas, e também buscando uma destinação ambientalmente correta aos resíduos que poluem. O objetivo deste trabalho foi utilizar planejamento experimental para estudar a absorção de água em cerâmica incorporada com lama vermelha. Foram tomados pontos experimentais, cujos teores dos materiais utilizados variaram de 0 a 100%, e as formulações queimadas a 950°C. A argila verde e as misturas contendo maiores percentuais da mesma apresentaram menores valores de absorção de água e retração linear de queima. O modelo matemático que mais se ajustou foi o cúbico especial. Os resultados obtidos no planejamento de misturas mostram que para as três regiões experimentais propostas, o modelo cúbico especial foi o que mais se ajustou aos resultados reais, e que este é estatisticamente o melhor modelo matemático e deve ser usado para avaliar a absorção de água.

Oct 30, 2017

By Rodrigo Fina Ferreira, Jacek Kolacz, Luciana Gois, Neymayer Pereira Lima

The recent developments on the sensor detectors together with the higher capacity of the machines, due the high-speed computing recent advances, have made possible extending the application in the mining industry. The use of x-ray fluorescence, x-ray transmission and radiometric sensor based sorting can selectively remove gangue minerals in different size fractions for different minerals. This paper summarizes the potential application of SBS for an iron ore in three size fractions aiming to increase the %Fe after the removal of particles with main gangue minerals associated. Pilot plant tests were carried out with samples of iron ore in different size fractions and different content of hematite and gangues. The use of x-ray transmission sensor showed the possibility to increase the %Fe from about 63% to above 68% for particles below 80mm and 45mm, after the removal of low density particles. The presence of fines on the feed affected the performance of the SBS X-rays transmission machine, especially for the fine fraction feed. The mineralogical determination, carried out to know the association between hematite and gangue minerals, and the density of the particles on the feed, can be used to preview the quality of products of the x-transmission sorting process.

Oct 3, 2019

By Donald Crowell

Due to falling metal prices and depletion of ore reserves, lead-zinc mining in the Leadville, Colorado, area gradually came to a halt in the 1950's. Exploration work continued, however, and by 1969 sufficient ore had been blocked out to warrant sinking a shaft and erecting a new concentrator to treat 700 tpd. The new shaft and concentrator were to be located in Iowa Gulch several miles east of Leadville at an elevation of 11,100 ft. The Leadville project is a joint venture between Newmont Mining Company and ASARCO with ASARCO being the operator. Design work began in the fall of 1969. Engineering was done by Torkelson Engineering Company of Salt Lake City in conjunction with the Central Engineering Department of ASARCO. The plant was constructed by Stearns-Roger Corporation. Construction began in the spring of 1970 and the plant went onstream in April, 1971. Flow sheets and equipment lists are attached. This paper will describe the flow sheet very briefly and discuss in more detail those aspects of the design which may be of interest, particularly the provisions for expanding the capacity of the plant.

Jan 1, 1972

By P. G. Kovalchik

Overexposure to noise remains a widespread, serious health hazard in the US mining and other industries despite 25 years of regulation. Most categories of illnesses and injuries associated with mining have improved, with the exception of hearing loss. The drilling of rock in a confined work environment contributes to high levels of noise exposure in mining. The National Institute for Occupational Safety and Health (NIOSH) is conducting research to reduce the noise exposures of jackleg drill operators and to prevent additional cases of noise induced hearing loss (NIHL) by developing and evaluating low-cost retrofit noise controls for equipment. This report describes the procedure for the measurement and reporting of noise from portable pneumatic tools such as jackleg drills. The technique used in this research allows for the determination of the source A-weighted sound power levels and the radiation patterns in octave and 1/3 octave bands. Overall sound power level is also determined. This paper also reports the results obtained by using this procedure to evaluate a SECO S215 standard production drill and a CSIR Miningtek prototype rock drill incorporating engineering noise control measures. It was found that by using the manufacture?s recommended operating pressure of 496 kPa (72 psi) that the CSIR prototype?s sound power was 10 dB(A) less then that of the SECO S215.

Jan 1, 2009

By A. J. Lynch, L. Ergun, M. Oner

"A research program on modelling cement grinding circuits has been in operation at Hacettepe University, Ankara, for four years. It has concentrated so far on tube mill and air separator grinding circuits for cement clinker, with emphasis on plant sampling surveys, including axial sampling inside the tube mills. The data used for model development have come from 33 surveys in 9 plants.The operating conditions have been:- mill sizes - 3.2 to 4.8 metres diameter and 8.5 to 15 metres long,- mill feed rates - 46 to 158 tonnes per hour,- air flow through mills - 25000 to 125000 cubic metres per hour,- cement clinker work indexes - 10.3 to 18,- separator sizes - 2. to 3.1 metres diameter,- separator feed rates - 132 to 689 tonnes per hour,- separator speeds - 12.3 to 21 metres per second.The ball mill model is Whiten’s perfect mixing model and the separator model is the Tromp curve with a fish-hook. This paper emphasises the importance of calculating the breakage rates and the discharge functions with three case studies at five different circuits which were selected for discussion because they show how particular features of circuit operation can be included in the general models. Size distribution graphs are used to illustrate every aspect of the discussion"

Jan 1, 2003

By J Penman, N Turner, H Liu

This paper aims to present a snapshot of the risk profile for tailings storage facilities within Western Australia by comparing the spatial distribution of known facilities against common geohazards such as cyclonic activity, climate, and peak ground accelerations from earthquakes. The analysis also includes an assessment of proximity to populations at risk including towns and sensitive receptors including significant river systems and wetlands.

Jul 1, 2021

By S N. Donaldson, B L. Hollis, K Wynn, L Potts, M Evans

A real-time load-haul-dump (LHD) dispatch optimisation tool has been deployed at Panel Cave 1 and Panel Cave 2 at Newcrest’s Cadia Valley Operations. The tool, known as ORB, is the first known successful implementation of an optimisation-based, autonomous, real-time dispatch tool, custombuilt for underground mining operations. ORB can co-ordinate the optimal dispatch of LHD’s in a block cave to achieve a range of objectives while adhering to draw compliance and geotechnical constraints. It is an example of highly automated short-term interval control. This paper starts by outlining the pre-existing business planning process, detailing the simple logic that produced the daily draw order. Next, the motivations for a real-time dispatch tool are presented, drawing comparison to the limitations in existing planning processes and how these can be overcome through an optimisation-based, autonomous, real-time dispatch tool. Subsequently, the paper details the Ratio Bogging Draw Strategy, through which tonnes targets are expressed continuously on draw bells or draw points as a ratio of total cumulative cave draw. This signifies artificial planning boundaries are removed and that draw targets are linked within a cave; such that tonnes are unlocked by bogging other parts of the cave, instead of as a function of time. This creates incentive within the target mechanism for fixing and bogging struggling draw areas whilst allowing uncapped progress if all draw targets are progressing within compliance. Furthermore, the optimisation tool developed is outlined, including the data it uses and the objectives it optimises. Finally, detail on the improvements to operations the implementation of this tool has brought, and the business process change it has facilitated are presented using Newcrest’s Cadia Valley Operations as a case study.

Mar 15, 2021

By B. Larsen

The Søderberg electrode was invented about 95 years ago by the company Elektrokjemisk, later known as ELKEM. It is still the most commonly used electrode system in submerged-arc furnaces for ferroalloys, platinum smelting, and slag cleaning operations. The size of the furnaces and electrodes has increased over the years and electrode diameters up to 2000 mm are today in use. Such large electrodes can be challenging to manage, and large electrodes are also more demanding when it comes to the electrode paste used in the electrodes. Although electrode sizes and equipment around the electrodes have changed, the main principles of the Søderberg electrode processes are the same. To assists in proper understanding of the electrode processes and to optimize electrode management, Elkem has developed several mathematical tools covering various aspect of the process. Both temperatures and thermal stresses can be calculated during dynamic conditions. The paper demonstrates, with examples, how the tools are used in both education and as practical input to improved electrode performance.

Jan 1, 2012

By G. F. Loughlin

Nearly 55 years have elapsed since the U. S. Geological Survey was organized. During this period the mineral industries have grown from infancy or early childhood to well developed maturity, and some mining industries appear to be declining. Decline in mining is even more conspicuous in certain districts, or even states, than in any mining industry as a whole, and discoveries or developments of important new districts have been very few in recent years. Our reserves of most metals and nonmetals are adequate for many years of normal production, subject to changes in rate of exploitation that may be caused by foreign competition and by changes in technology and market conditions; but the declining production of many districts and the scarcity of important new discoveries to compensate for them is cause for some apprehension. It is likely that future production will depend to a considerable extent on deep exploration and on the thorough examination of places in and adjoining existing districts where significant outcrops are lacking and only apparently insignificant geologic features offer encouraging clues—more so than on the discovery of entirely new districts. Even the possible discovery of new districts, which have escaped the intensive search by the nontechnical prospector, must be dependent on geologic information. There is therefore no need for argument as to the value of geology to the mining industry; and the need of continuing to advance the science. The U. S. Geological Survey's past contributions to mining geology, as expressed in its official reports and other publications, are recognized by Ransome in his historical review of mining geology in the Lindgren volume.' These contributions have helped to form the basis of modern mining geology, which has grown rapidly in the last 25 years. This growth has witnessed the organization and maintenance of geologic staffs by mining companies in several districts, and their detailed work, together with the fact that nearly all of the larger mining districts have

Jan 1, 1935

By Peter G. Chamberlain

The Bureau of Mines is conducting research to boost domestic production of manganese. Virtually no mining exists in the low grade and/or small deposits that occur in this Country. One large, low-grade manganese deposit located in westcentral Arizona--The Artillery Peak district--was extensively studied and sporadically mined during the 1940's and 1950's. Although manganese mining in the district has been long dormant, recent studies indicate that the deposits may be amenable to economical production by heap and/or in situ leaching methods. A conceptual design for an in situ leaching system features undercutting and blasting a block of ore, leaching with SO2, and extracting the manganese as a sulfate or oxide. Possible applications to other manganese deposits depend upon formation permeability and specific manganese mineralogy.

Jan 1, 1981