Search Documents

By John Nagy

Tests were conducted in the Experimental coal mine to study some of the factors that should be considered in fighting mine fires and to obtain data on the effectiveness of different types of extinguishing agents. The investigation was confined to class "A" fires in a zone 20 feet long, involving coal burning on the floor, on the floor and ribs, and on the floor, ribs, and roof of the mine entry. It was determined that the time elapsed between ignition and attack of the fire is very important. A fire in the early stages was found to be controlled more easily and quickly than a similar fire that had burned longer. It was also found that, under suitable conditions, a fire in the floor, ribs, and roof develops very rapidly and consequently might spread over a considerable area if not brought under control quickly. The ventilating current affects fire-controlling operations markedly. Attack in intake or fresh air is highly advantageous, the chief inconvenience being the radiant heat from the fire. Attack in direct return air was impossible for the fires tested in this investigation, because of the high temperature. Universal-type gas masks for noxious gases and smoke offered no protection against the intense heat. Approach to a fire in the return air behind a water-fog curtain is not feasible unless the direction of air flow can be reversed. In one" test fresh air was carried to the fire area with a line brattice. Although the entire controlling operation was in fresh air and masks were not necessary, it was considerably more difficult to control the fire than when a similar fire was attacked in intake air.

Jan 1, 1950

By D. A. Bird

Geochemical models using published thermo-dynamic data and laboratory derived kinetic rate laws allow prediction of post-closure pit lake geochemistry at open pit mining sites. A combination of "forward" and "inverse" modeling techniques can predict the pit lake geochemical evolution from initial infilling to eventual steady state attained decades or centuries after closure. Computer codes have been developed to model chemical reactions such as pyrite dissolution, describe the ground-water flow regime, and provide rock-water ratios. The incorporation of site specific information, such as ultimate pit dimensions, geologic and hydrologic data, acid generating potential (AGP) vs. acid neutralizing potential (ANP), and laboratory derived kinetic rates, allows application of the model to open pit mines at any stage of development.

Jan 1, 1994

By Robert P. King

In April, 1975 the Colorado School of Mines began monitoring rock mass response associated with a long- wall shield demonstration project near Raton, New Mexico. This project was sponsored by the U. S. Bureau of Mines (DOE) and performed at Kaiser Steel Corporation's York Canyon Mine. Two of the results of the intensive instrumentation effort are the empirical subsidence and horizontal strain models presented herein. These models are based on data gathered during mining three adjacent longwall panels (4N, 5N and 6N). A total of 251 permanent surveying monuments were monitored over the three-panel area. Lines of monuments were oriented along panel centerlines, perpendicular to centerlines and diagonal (45O) to centerlines. Active monuments were monitored twice a week, with less frequent monitoring of stable or slow moving monuments. Primary subsidence monitoring equipment consisted of an AGA Geometer Model 75 and a Wild T-2 Theodolite with -a Wild-Sercel DI-3S distomat.

Jan 1, 1979

By James H. Bechtold

The yield strength of annealed tungsten was found to have a strain rate exponent 12 times as great as that of low carbon steel. The effects of temperature and strain rate could be correlated through the Zener-Hollomon parameter with a heat of activation associated with yielding of 32,000 cal per g-atom. This heat of activation is independent of strain although both the temperature and strain rate dependence of the yield strength vary with strain. MOST metals have mechanical properties that are relatively insensitive to strain rate, especially at temperatures below that at which creep is important. In iron and molybdenum," however, relatively large strain rate effects are observed in the temperature range where the rapid increase in yield strength occurs which leads to the ductile to brittle transition. In this temperature range Zener and Hollomon' have suggested that the effects of strain rate and temperature T on the yield strength could be correlated through a single parameter, P, in the following manner where Q is a heat of activation characteristic of the metal and associated with some unspecified relaxation process. They also observed that if the temperature is restricted to a relatively narrow range— below room temperature for steel—that the logarithm of the yield strength could be expressed as a linear function of the logarithm of P. From this relation the logarithm of stress should be a linear function of the logarithm of the strain rate at constant temperature: where r will be referred to herein as the strain rate exponent. At a constant strain rate the logarithm of stress should be a linear function of l/T, ay(e = C) ~ eT [4] where q = Qr [5] and is referred to herein as the temperature exponent. These equations have been found to relate the effects of temperature and strain rate on the yield strength of molybdenum in the temperature range wherein the ductile to brittle transition occurs, —75° to +150°C.2 Bechtold and Shewmon3 have shown recently that the ductile to brittle transition in annealed tungsten occurs in the temperature range +150° to +350°C. In this temperature range the yield strength in-

Jan 1, 1957

By Dr. Calvin J. Konya, Anthony Konya

Blast violence has always been a criteria that has been analyzed without a quantitative approach relying on opinions of those viewing the blast and oftentimes does not transfer between open-pit mines, quarries, and construction projects. Added to this confusion is that on many regulate projects, such as U.S. Army Corp of Engineers construction projects, the definition of "flyrock" or violence can vary, and contractors must be able to meet this requirement. This project analyzed hundreds of blasts from various construction projects to develop a new metric to determine blast violence - the Violence Factor. If a blast is fired using 1.25" (32 mm) diameter product and a 10-foot (3 m) bench, vertical uplift of 60 feet (18.3 m) would be considered extreme and violent by any professional in the industry. However, a 100-foot-high (30.5 m) bench using 12" (305 mm) bulk product, having a vertical displacement of 60 feet(18.3 m)might be considered typical or non-worrisome. This is where violence factor is beneficial as itprovides a system of scaling the violence of a blast based on the bench height to give manager a keyperformance indicator (KPI) which is easy to monitor and can provide a large amount of information onsite-specific design variables for their performance on blasting and the end-results of the blast. The Violence Factor of a blast is an integer which is scaled to determine how high vertical uplift of a blast is compared to the bench height. This project analyzed numerous blasts to determine what blast design variables contribute to violence. This violence has also been shown to occur when a non-optimal breakage mechanism, cratering, occurs and the design criteria that lead to this cratering. Finally, this paper will present typical results of various levels of violence including backbreak, fragmentation, and muckpile configuration.

By William Petruk

An investigation was conducted to determine whether mineral liberation data obtained by one image analysis technique are the same as data obtained by another image analysis technique. The liberated vs non-liberated, volume % and weight % techniques for measuring mineral liberations by image analysis were tested. The results show significant differences between the values obtained by the different techniques. The lowest liberation values were obtained by the liberated vs non-liberated technique and highest by the weight % technique. It is interpreted that the weight % technique produces the most realistic results. The weight % technique also produces data that can define mineral associations for the unliberated grains. These include (1) mineral quantities in particles that contain different amounts of unliberated mineral, (2) mineral quantities in particles that have different size ranges, and (3) mineral quantities and degrees of liberation for specific minerals in particles of different size ranges.

Jan 1, 1996

By Q. Han

A modified cast-on method has been developed to reinforce aluminum castings with steel insert. Defect-free bond between the steel insert and the aluminum casting has been consistently obtained. Data obtained from a push-out experiment indicated that the bond strength was much higher than that obtained using the Al-Fin approach. This paper introduces this modified method in four sections: the coating of the steel pins, the cast-in method, microstructure characterization, and the bond strength. The section on the coating of the steel pins contains coating material selection, electro-plating technique for plating Cu and Ni on steel, and diffusion bonding of the coatings to the steel. The section on cast-in method deals with factors that affecting the quality of the metallurgical bond between the coated steel and the aluminum castings. The results of microstructure characteristics of the bonding are presented in the microstructure characterization section. A push-out experiment and the results obtained using this method is described in the section of bond strength/mechanical property.

Jan 1, 2015

By Martin J. Hughes

The Eagle Mountain Mine of the Kaiser Steel Corporation is located in the California portion of the Colorado Desert at a distance of about 60 miles east of Indio, California. At the present time, this mine is producing at the rate of 5,000,000 tons of concentrate per year. A total of 1,000,000 tons of ore per year is presently being sold on the Japanese market while the remainder is consumed by the Kaiser Steel Company blast furnaces at Fontana, California. A new Pellet Plant and Concentrator is presently under, construction with completion scheduled for May or June 1965. This plant will have a rated capacity of 2,200,000 tons of pellets per year and essentially all of this production will be sold to Japanese steel companies.

Jan 1, 1965

By George Kazonich

The high costs and environmental problems associated with making iron and steel in the United States is driving the development of new technologies to replace the blast furnace. A prototype reactor incorporating rocket technology was designed and built. This rapid rate reactor was operated successfully and consistently made iron metal. Minus 325-mesh magnetite particles could be reduced to iron metal in less than 50 ms in a high temperature flow through reactor. Iron product was recovered inside the reactor and in a downstream cyclonic separator. The results of typical operation and how parametric changes affected the reduction of iron ore concentrates are discussed.

Jan 1, 1993

By John L. Watson

The dewatering of steel industry waste sludges prior to discard or recycling often presents significant problems due to the fineness of the sludge particles, which may blind the filter medium and/or produce a cake with limited porosity, Several steel plant wastes, such as sludges from BOF and EAF gas cleaning operations exhibit not only a very fine particle size, but also some degree of magnetic character, A novel process has been developed to utilize the magnetic character of such sludges to enhance dewatering through a multi-force operation involving magnetic, chemical and vacuum forces, The process consists essentially of undertaking vacuum filtration of a flocculated sludge in a magnetic field, This is achieved by installing a permanent magnetic in a fixed position on the axis of a vacuum drum filter, thus effecting filtration of magnetic and non- magnetic particles, bound together in flocs, in a magnetic field, Previous tests using a modified laboratory vacuum drum filter treating artificial (magnetite) and industry waste (BF sludge) feeds have demonstrated that filtration capacity may be enhanced significantly with increases of up to 3000/0, An explanation of the mechanisms associated with the enhanced filtration was not obvious, and this research was undertaken to permit the cake formation in the magnetic field to be monitored to provide an insight into the manner in which particles agglomerate to form the cake. These tests revealed that the magnetic field caused magnetic particles to be aligned perpendicular to the filter surface and to form channels through which filtrate could freely pass thus increasing capacity, The effects of various magnetic fields and field strengths on the filtration process were also investigated. A simple computer model was constructed to demonstrate the proposed theory of multi-force dewatering, The model output graphically illustrated the suggested mechanism and confirmed the enhanced capacity of the novel dewatering process,

Jan 1, 1996

By Natalie Zeleznik, Brian Hawkins, David Bradley, Rachel Gooding, Patrick Wilson

"The United States (U.S.) Department of Homeland Security (DHS) Directorate of Science and Technology (S&T), utilizes a probabilistic risk assessment (PRA) approach to explore the risks (anduncertainty) from chemical, biological, radiological and nuclear (CBRN) threat agents to the Homeland.This end-to-end risk methodology considers a broad range of hazards incorporating emergingtechnologies, available countermeasures and input from the Intelligence and Law Enforcementcommunities (IC/LE) to evaluate the acute risk to human health due to an attack on the U.S. homeland. The PRA generated output provides a mechanism to examine risk mitigation strategies, critical vulnerabilities, critical data and knowledge gaps and relative risk rankings of materials, targets, classes of compounds and scenarios."

Jan 1, 2017

By Jirí Faltus

The paper deals with studying the impact of structural properties and anodizing of surface on the corrosion properties of extruded rods from commercial aluminium alloys: AA6082, AA6262, AA6012, AA2007 and new lead-free aluminium alloys AA6023, AA2015 and AA2111B. Samples were exposed to the corrosive atmosphere NSS, AASS in the chamber by EN ISO 9227. Surface of samples were either in the original state or anodizing by selected mode. The depth of corrosion attack and the form of corrosion attack are evaluated depending on the type of alloy, the metallurgical condition and surface treatment of the samples.

Jan 1, 2015

As part of the Bureau of Mines subactivity in secondary resource recovery and to expand the Nation's mineral base, the Tuscaloosa Research Center made characterization and preliminary beneficiation studies of the waste residues from various coal-conversion processes: from pilot plant tests of the Synthane process for coal gasification, the Synthoil process for coal liquefaction, and the solvent-refined coal (SRC) process for sulfur removal from coal. Those coal conversion processes selected for this study were based on the availability of pilot plant samples. Physical, chemical, and mineralogical examinations of the wastes made to determine the mineral content prior to physical beneficiation tests indicated that in addition to significant quantities of carbon, some trace elements offer potential for concentration.

Jan 1, 1980

The past decade has seen remarkable progress by the railroads both in equipment and concepts in the handling of dry bulk. materials. While such shipments have always been an important part of the traffic handled by the railroads I little was done to improve the efficiency of handling or toward attempted optimization of equipment design before 1960. Several developments at about that time turned attention to this important segment of railroad traffic. One was the construction of a successful coal slurry pipe-line. Another was the promise of substantial economy in electric power transmission by ultrahigh voltage systems and finally, came the growing technological and economic feasibility of nuclear fuel electric generating plants. Each of these developments was a threat to the coal traffic of the railroads --the most important single commodity they handled in terms of revenue and tonnage. By the mid-1950's I Southern Railway management had become most concerned with its growing investment in freight car equipment and the declining revenue productivity of the capital employed. Additionally I there was substantial concern with the loss of business and potential losses in the area of the railroad's greatest economic advantage --bulk commodity movements. In 1958 a small team was established to study this problem. They arrived at two conclusions. The first conclusion was that within limits of maximum gross allowable weight on rail the lowest unit net capacity cost of investment came at maximum allowable gross weight per car unit. The second conclusion was that with a high degree of utilization costs per weight unit transported could be reduced to the pOint where

Jan 1, 1971

By A. E. J. Gallagher

There are many influences which have a bearing on the economics of industrial minerals production. The purpose of this paper is to discuss briefly three factors which have economic significance in the production of these mineral commodities. The three items of discussion include 1) the nature and relative value of the industrial minerals group, 2) project planning, and 3) market analyses. General aspects of these factors are familiar to most of us. However, an attempt will be made to give some current details regarding each. Also, in reality, project planning and market studies are usually so closely associated that they will be discussed jointly, rather than separately. This will be done by way of examples which show how these two activities actually evolved for two industrial minerals projects.

Jan 1, 1984

By T. Majcherczyk

Shaft lining reinforcing analysis of two shafts under construction has been presented in this study. The first shaft was driven from the surface, while the second was deepened. Mining and geological conditions have been studied with respect to the lining capacity. The improvement of shaft stability comprised two elements, i.e. reinforcement of the shaft lining capacity and improvement of the strength properties of the rock mass. In both tested cases, the particular hazard was connected with non uniform loadings of the lining, which could generate shearing stresses within lining structure. Thus such elements as armored concrete with high strength properties, bolting and injection sealing of the rock mass, and the use of special ring reinforcing the shaft lining have been used in order to reinforce the shaft-rock mass system. Practical conclusions related with new technological solutions, allowing the rock mass and shaft lining reinforcement, have been included for the present study. Practical conclusions related with new technological solutions, allowing for rock mass and shaft lining reinforcement, have been also included to the present study.

Aug 1, 2013

Existing geological structures such as faults or shear zones can greatly influence the interpretations of amplitude or energy attenuations of measured blasting vibrations along both affected and unaffected orientations. Mineralisation in conjunction with large faults or shears is commonplace in the geology of steeply dipping metalliferous deposits, such as those found in the goldfields of Western Australia. Better understanding of the influence of faults or shear zones on blast-induced seismic waves can lead to more effective blast vibration monitoring programs and interpretation of the results measured along affected orientations.

Jan 1, 2011

By R. W. Coburn

The results of field experiments on wells which required stimulation indicated that engineered well-completions will cause an increase in ultimate recovery at reduced costs. Techniques and tools have been developed which can be used to establish well conditions most conducive to successful stimulation. Cementing, perforating and treating are bound together so completely that the success of one phase is completely dependent on the .effectiveness of the preceding phase. A method of determining the efficiency or effectiveness of any given well-stimulation treatment has been derived. Pressure behaviour during a treatment can be analyzed to yield the total percentage of the formation which has been treated.

Jan 1, 1960

By Q. J. Liu

The flotation circuit and the reagents of the all-sliming flotation about low grade and hard operation on zinc oxide ore are researched in the paper. The results indicated that there are many types of zinc minerals in this ore, and the composition is very complex. They include hemimorphite, smithsonite, hydrozincite and so on. The ore is seriously sliming. In light of the ore properties, three kinds of flowsheets have tested. They are gravity concentration (cleaning tables), flotation, combined process of gravity concentration and flotation. The test showed that the recovery of zinc is only 17.08% in the gravity separation. In combined process of gravity separation and flotation, the recovery of zinc concentrate is close to 70%. But the flow-sheet is complex and hard to control in the production. The floatation circuit is feasible. In the test, it pay attention to investigate the new combined reagent which is used in selective all?sliming flotation process. The effects of slime are eliminated by the multi-loop treatment of middling. In flotation, the final recovery of concentrate is 88.76%; the grade is 29.50%. The recovery of physical ore is 93%; and the recovery of -10mm fraction is more than 65%.

Jan 1, 2014

By K. Spence

"The notion of “value” has always been a subjective and contentious issue. Indeed, value is in the eye of the beholder. There are as varied methods and practices for valuing property, as there are industries in which they are applied. For example, there is replacement value, insurance value, salvage value, appraised value, book value, and fair market value, to name a few, although in the mining industry, valuations usually refer to fair market value.In the Canadian mining industry, at present, there are no comprehensive regulations or guidelines that specify which approaches or methods are appropriate for use in the valuation of mineral projects. In January 1999, The Mining Standards Task Force of the Toronto Stock Exchange and the Ontario Securities Commission recommended that the Canadian Institute of Mining, Metallurgy and Petroleum (CIM) establish a committee to review and advise on approaches and methodologies for the valuation of mineral properties. Among the approaches to be considered are included the following: the discounted cash flow approach, the cost approach, the option pricing approach and the market comparables approach. In addition, methodologies differ depending on whether the project is at the exploration stage or the producing stage.The CIM Special Committee on the Valuation of Mineral Properties (CIMVal) expects that its final report will form the basis for a Canadian code or standard for the valuation of mineral properties."

Jan 1, 2002