Search Documents

By Gerhard Derge

A SERIES of studies of the corrosion of tin is under way in the Metals Research Laboratory at the Carnegie Institute of Technology. The complete program includes examination of the corrosion properties of high-purity tin and the changes produced in these properties by the addition of varying amounts of alloying elements. Other studies of this subject have been made recently under the sponsorship of the Inter-national Tin Research and Development Council, but these researches have been confined largely to the weakly acid environments commonly encountered in the canning industry.1 There is little information avail-able regarding the corrosion of tin under alkaline conditions, but such data would be of value, for a large amount of the metal is used under such conditions. The potential measurements to be described were made because they seemed to offer the most rapid method for obtaining a general view of the conditions to be encountered in such service. These experiments will also serve to establish a technique that will be of value in further studies. It must be emphasized that the results reported are those of controlled laboratory experiments and that the conclusions drawn cannot yet be applied to service conditions; rather, they point to the directions in which, more exhaustive experimental work may be clone to best advantage.

Jan 1, 1938

By Henry R. Tiedemann, Eugene H. Skinner, George E. Wickham

Improving the state-of-the-art of tunneling is a continuing challenge to those involved in underground construction. New methods and procedures are usually evolved over a relatively long period of time as compared to advancements in other types of construction. To a large extent this is probably due to the fact that tunneling deals with a material or medium - the rock structure - whose physical properties are not only extremely varied, but in many instances virtually unknown until time of penetration. This hovering of the unknown tends to make "non believers" of many and at best leads to a general reluctancy of accepting new ideas or procedures. The situation is further complicated by: 1) discrepancies in terminology and respective meanings as used by different disciplines to describe, define or evaluate pertinent factors and their relative effect on the tunneling process and 2) the fact that no two tunneling situations are identical with respect to either geological conditions or construction and contractual requirements. In spite of the above there have been many successfully completed tunnels which make it apparent that both the technical and practical expertise needed to develop or project improvements is available within the industry. It is with this in mind that the RSR concept was developed. BACKGROUND This paper presents the findings and results obtained from contin-

Jan 1, 1974

By Hancock RG, Dewar GJA

The mining and exploration industry is governed both directly and indirectly by a complex and constantly changing regulatory and legal system, yet few technical professionals realise the extent to.which they are affected and that they are personally liable for any breaches. These breaches may result in criminal or civil prosecution that could involve significant financial penalties (to the extent that all personal assets are at risk) and even imprisonment. Generally, a professional at risk should be able to mount a due diligence defence in order to avoid or mitigate these consequences. Mineral property and company owners, directors, managers and employees are at risk, as are consultants, contractors and suppliers of equipment or consumables. Whilst all are liable for their personal decisions to act (or failure to act) in managing operations or carrying out directions, as well as for the actions of others under their control, the focus here will be on the exposure of the consultant. Consultants are usually driven by an internal desire to perform to a high standard because of personal pride in their work and concern for their professional reputation. However, there are an increasing number of external requirements for them to be able to demonstrate, if necessary, that their actions were based upon reasonable grounds and that their work conformed to current best practice standards. If they cannot do so, they may face potential personal Liability.

Jan 1, 1995

By G. L. Oldright

DURING 1919, in the face of high cost for labor and supplies and a rapidly dropping copper market, the management of the Ohio Copper Co. of Utah was left with an orebody that had been shown to be very low grade, and a mill that could not make a satisfactory recovery, even by flotation, because a considerable proportion of the copper minerals was oxidized. About seven million tons had been mined by the use of a caving system, the best of the broken ore extracted and milled, and the nature and copper content of the rest of the orebody fairly well determined. The rock of the whole mine was shown to run between 0.3 and 1.3 per cent. in. copper. As, the Ohio Copper orebody lies at the contact of the original sandstone (now altered to quartzite) with the quartz monzonite intru-sion that was the source of the mineralization at Bingham Canon, the rock was thoroughly shattered. It was shown further that the rock was mostly quart-zite, with a few quartz-monzonite "fingers" projecting into it. Although some of the old cleavage planes had been healed by resilicification so as to leave some of the copper minerals disseminated in the rock, a large proportion of these minerals was distributed along the cleavage planes.

Jan 10, 1923

By Yong Hack Lee

Electric Arc Furnace (EAF) dust is generated when scraps are treated in the electric arc furnace and usually classified as hazardous industrial waste in most countries. EAF dust usually contains 15 to 25% of zinc and 3% of lead. It is usually treated in rotary kiln (Waelz process) or landfilled after a solidification and stabilization treatment. Numerous methods have been proposed as the EAF dust treatment technology, but few of them are in operation as a commercial scale except the Waelz process. Korea Zinc performed a plant test in which 600 tons of EAF dust was treated using TSL (Top Submerged Lance) technology. The TSL technology is a low cost, proven technology for processing zinc-bearing residues. The EAF dust was first de-chlorinated and fed to the TSL furnace. Finally, clean slag satisfying toxicity criteria was generated and valuable metals such as zinc and lead were recovered as fume oxide. The fume oxide was de-halogenated by sodium carbonate and sent to zinc refinery to recover zinc and lead. The recovery of zinc and lead was 90% and 93%, respectively. Most of the dioxin in the EAF dust was discomposed so dioxin less than the Korean regulation limit was detected in the offgas, which proves that the TSL technology is the best solution to treat EAF dust.

Jan 1, 2006

By Gerhard Sauer, Heimo Gold

The main advantage of the New Austrian Tunneling Method over conventional drill and blast techniques, TBMs and shields is its outstanding flexibility. Many different support concepts help to cope with all but the most adverse conditions. A considerable variety of unique additional support measurements provide a functional tool when dealing with particularly difficult conditions or restricting requirements. The resulting adaptability of NATM with respect to geometric and geologic changes is a cornerstone to providing an economic design and to a safe and unhindered execution of the tunnel work. To take best advantage of this flexibility and to emphasize its cost-saving capacity, NATM explicitly extends the design period into the construction phase. In accordance with corresponding ground classes or other anticipated conditions, a number of basic support categories and an array of additional support measurements are established during the actual design phase. The decision for applying a particular support category at a specific location and for necessary additions to the given support scheme, however, is regularly made on site after each advance, and is determined by the key persons involved in the construction. Contract documents must reflect this approach to facilitate the execution of the work and to curtail construction costs. Biased distributions of risks, however, can adversely effect the envisioned benefits. Consequently, the respective responsibilities of engineer, contractor, and client need to be redefined.

Jan 1, 1989

By J. Parke Channing

IT IS most appropriate for mining engineers and in fact for all engineers to perfect themselves in leader-ship, because in the last ten years there has been a growing realization on the part of capital that there is no man who by capacity and training is better fitted to manage industrial production than the engineer. In high places the engineer and particularly the mining engineer is coming into his own. We have Mr. Hoover as Secretary of Commerce, Mr. Hammond as the head of the Federal Fact-finding Coal Commission, and Prince Caetani as Royal Italian Ambassador, all mining engineers. More and more in all industries is the manager more likely to be an engineer than he was five, ten, fifteen or twenty years ago, and the feeling is that the man who has had a technical training, whether from going to a school or from burning the midnight oil, makes a better manager than the man who has not. We find in mining that the best man for a manager is one who has had engineering, training. The manager who comes up from the office, from the purchasing department or from the transportation department may make a fairly good manager but he is never so good as the man who has had a technical training. He cannot speak the language of his staff.

Jan 5, 1923

By Gil Espejo, Denise Duncan

"In Alberta, several initiatives are under way to form partnerships between educators and industry to work together in preparing a skilled and technically competent workforce for the future. One successful initiative is the Teachers in Business program which provides high school teachers one month paid internships in Alberta businesses. Initiated by the Science Alberta Foundation in 1992, this program has offered participating teachers a variety of work experiences and job shadowing tours in industry.A Growing Need of Education and Industry PartnershipsIn our ever evolving world, industry is in a tight race to keep up to date with new technology and to remain competitive. Industry is relying on the education system to provide them with the core base for their future workforce. To accomplish this, the education system needs the support of industry to develop the right focus to prepare its students for the race. What skills will our future workforce need? How can we best prepare our students for these needs?Teaching the latest in technology, especially at the high school level, is a major challenge. It is difficult for educators to keep abreast of the rapid changes in technology. High school graduates need exposure to the latest advancements. And so do their teachers. Students must be prepared to adapt to the challenges of the future, Le. global competition, rapid technological change and an expanding knowledge base."

Jan 1, 1995

By Ken J. Richards

Industries dependent on pyrometallurgical processing generally find themselves facing a common set of problems, namely, serious environmental restrictions, heavy capital requirements for new facilities and for plant modernization, the certainty of rapidly escalating fuel costs, and the uncertainty of fuel availability. To remain competitive, it has become clear to industry that a new dimension of attention must be given to assuring the maximum performance from plant facilities already in place and from those that are built in the future. In the last decade or so, in response to these needs, there has been an acceleration in the development of new pyrometallurgical process concepts. Their application, though spotty, is increasing. A common factor in this developing base of technology is the need for effective process control. Digital control is an indispensable element of meeting the challenge. We cannot make the point, however, by looking to a general survey of instrumental control of pyrometallurgical processes. Computer control is in its awkward adolescence. Its application is so new that only isolated applications can highlight the trends. For this reason, the authors have chosen to focus on the nonferrous smelting industry to illustrate the status of pyrometallurgical processing and control. We believe this approach will best meet the interests of most readers of this edition and the background of the authors.

Jan 1, 1979

By J, J M. Young, P T. Nielsen, R Zhu

Improved understanding of the variables that influence hydrocyclone performance is of increasing interest to the iron ore industry, where hydorcyclones are widely used to deslime fine ore. In many cases, the impact of particular variables is not quantified sufficiently well experimentally to ensure that industrial performance will match expectations. The current work focused on developing and implementing a systematic methodology to evaluate and compare the performance of four different hydrocyclones in a desliming application. A critical component of the project was the design and construction of a pilot-scale hydrocyclone rig using state of the art monitoring and sampling methods. A wide ranging test programme was conducted to quantify the effect on metallurgical performance of the key hydrocyclone variables such as pressure, feed density, vortex finder size, spigot size and hydrocyclone make/overall design. Details of the experimental approach are presented, along with a discussion of the sizing analysis methods used. Performance criteria were established to assess the four hydrocyclones. The effects of each major variable were quantified over a wide range of conditions. The results show that clear performance differentiation was achieved, enabling the selection of the optimum configuration. The results from this work demonstrate the benefit of objectively assessing the performance of nominally equivalent units in selecting an optimum configuration that best satisfies the performance criteria.

Jan 1, 2002

By J. P. Savely, D. E. Nicholas, R. D. Call

Progress in the technology of slope design over the past 15 years now permits the selection of rational slope angles if suitable data on geology, hydrology, and rock properties are available for a specified project. Although a full-scale slope design study remains the best course of action, there are situations where an extensive study is not feasible due to time or budget constraints. Two typical examples are: (a) selecting pit slope angles for a preliminary feasibility study at the exploration stage; and (b) coping with a slope failure in an operating mine. In both instances, slope angles must often be chosen on the basis of data that are currently available or can be readily obtained. All too often during exploration programs, a feasibility study is initiated shortly before the decision deadline to drop the property or proceed to purchase. If the only existing data at this point are a few cross-sections at odd angles showing ore and waste contacts or a dog-eared map of the surface geology, there may not be time to collect and organize sufficient information for the design of slope angles. On the other hand, if during the drilling program geologic cross-sections were constructed and the structural data compiled in tabular form, rational slope angles could be computed within the allotted time.

Jan 4, 1977

By H. R. Hanley

ONE of the most important contributions to the art of electrolytic zinc production-has been the aluminum cathode. This has been used in all major production: since its commercial development in 1916. The literature is replete with important contributions, some of which may have been replaced by better ones, but thus far there appears no other metal to take the place of aluminum as cathode material. Credit for this innovation goes to Sherard Cowper Coles, of England. When experi-menting on the extraction of-zinc from Broken Hill ore at Hayle, Cornwall, in 1893, he introduced the aluminum cathode, and in 1895 obtained British Patent-No. 20073. The reason for this dominant position of aluminum as cathode mate-rial in zinc sulphate electrolytes is its unique surface, to which electro-deposited metals usually do not tightly adhere. The metal must be of high purity for best results. It is possible to develop a starting-sheet method by which thin electro-deposited sheets of cathode zinc are made and stripped from a smooth aluminum plate. Such thin sheets of cathode zinc may be used as arc tine copper sheets in standard electrolytic copper-refinery practice. However, complications arise because of extreme warping of the zinc starting sheet after a .few hours of deposition, and thus special arrangements must be made to compensate for this abnormality.

Jan 1, 1938

By G. J. Melvin

Mines the world over tend to face a common range of problems. They begin life by trying to determine if there is sufficient product, usually under tons of earth, of sufficient quality to justify the operation. Once such a determination is made the mine must then be planned and brought into operation. Once operating most mines find that they are far away from suppliers, using very expensive equipment. Hence the three most common mining problems are, what does my ore body look like and how can it best be mined, how can I get sup- plies to my mine in the most cost effective way, and how do I control the vast dollars required to keep it all operating. Mincom started life by providing technical mining software to address the first of these problems and was very successful, particularly in the coal mining industry. However the company soon realized that if it was to become a significant provider of mining industry software it must also address the other major problem areas. Hence started what is now Mincom's largest business which is the provision of fully integrated mine management software with strong emphasis on materials and maintenance management to control costs. Mincom not only supplies the software but also provides a comprehensive implementation package using its own staff of experienced mining industry specialists. This papaer highlights some of Mincom's international implementation experiences.

Jan 1, 1989

By D. D. Bolstad, S. M. Dar, T. W. Smelser, H. C. Pettibone

The use of roof bolt supports has reduced the number of fatal and nonfatal roof fall accidents in coal mines. Roof fall accidents, however, still occur far too frequently. Roof bolting plans are based almost entirely on trial and error, which inevitably leads to underdesign or overdesign with regard to bolt length, spacing, tension, and bolt type for the specific conditions. Underdesign poses safety problems, and overdesign leads to unnecessary costs. Guidelines are needed to select and design optimum roof-bolt plans that will maximize safety and minimize cost. Despite the use of 100 million roof bolts per year, the theory of roof bolting remains underdeveloped. Underground tests designed to provide this knowledge have been only partially successful owing to the many uncontrollable geologic variables present in underground mining situations. The Bureau of Mines believes that the best approach is to conduct a laboratory model study in correlation with finite-element analysis (FEA) and field verification, where these variables can be tightly controlled and measured. A physical model allows precise performance measurement of different bolt types as a function of a wide range of precisely measured parameters. Although the model being used is idealized and limited in size, it serves as a reliable basis for confirming the mechanism of rock reinforcement by bolting and the accuracy of the computer FEA approach to modeling mining problems.

Jan 1, 1984

By T. Yalcin

It is well recognized that machine type and machine characteristics play vital roles in the successful application of froth flotation in mineral processing. Since the early 1900s, a multitude of machine designs have been and are still being introduced in an attempt to improve flotation efficiency. Machines based on mechanical agitation have been the most dominant in industrial practice. However, in recent years there has been a growing interest in pneumatic flotation units because of their claimed simplicity, low cost, high throughput and good metallurgical performance. This work was carried out to assess the effectiveness of pneumatic flotation on a magnetite ore. The method was applied using a prototype pneumatic flotation device that utilized a suitable nozzle for bubble generation. Important variables of the process were examined and optimized, including the nozzle size, air flow rate and froth thickness. Further tests were conducted to determine the influence of frother dosage and to explore the improvements that could be made on concentrate grade and recovery by cleaning and scavenging. Under the best test conditions, an iron concentrate was obtained with a grade of 66.4% Fe and a recovery of 97.7%. Particularly, the recovery was superior in comparison to that of mechanical flotation. This was attributed to the ability of pneumatic flotation to create and maintain a relatively thick froth layer.

Jan 1, 2002

By Jaril B. Lavrencic

The unique and irregulator distribution of working places in a mine always poses the two questions: - which and how much production equipment is to be used, - what production can be expected. Since the development of analytical methods would be impractical for such cases, a lot of computer programs has emerged in recent years trying to simulate the productiom process and thus find the best answer. The usege of a simulator has its dark side well felt by the author(s) of such a program: the credibility and the confidence of the customer. Using the simulator means to respect and to incorporate all the restrictions imposed by the narow underground space, methods of production, safety regulations etc., which can turn out to become a major programming effort. If the program is not properly structured, it will be used for a single special' case only, and never again. In this paper the structure and internal mechanism of the simulator is described for which the author believes that can easily be adapted to conditions of various underground and open pit mines. MINSIM tries to reach the following rather ambitious goals: 1) Estimation of the production before opening the mine, or a part of the mine. 2) Training the personnel to make decisions. 3) Making the daily time schedules for the entire fleet of the equipment units.

Jan 1, 1989

By John Clarke Holman

Industrial growth and survival in today's competitive world means both economic efficiency and technological superiority. Superior technology includes not only exploiting the best methodologies and techniques presently available, but also a continuous search for and development of, better ones. In practical terms this translates into an investment of substantial sums of money. Of course, even a relatively small investment will not be justified if the fruits of the project cannot be secured to the investor and the inventor alike. There are at least three ways to protect new or improved technology. If the improvement reaches the height of an invention, "patenting" usually is the preferred mode of protection. If, however, the improvement is novel and valuable but does not satisfy the requirements of the patent laws, one may then consider "trade secret" agreements as a means of obtaining appropriate return for the investment made so long as the improvement is capable of being maintained in secret and cannot be "reverse engineered." If one develops a new and useful organism and seeks immediate protection from infringers, current thinking is that the copyright law may afford such protection simply by publishing the genetic code. Here is one instance where you may publish without perishing! This paper will endeavor to highlight the pros and cons of various legal mechanisms and their applicability to the frontiers of technology.

Jan 1, 1985

By W. H. Davitt

While it is true that taxes, especially income taxes, whether they be federal, state, or local, are not usually thought of as a "cost" of doing business, it is equally true that these tax costs do reduce the distributable profits just as much as the cost of power, supplies, or labor. Therefore, the consideration given to taxes is often as important as that given to other costs. Hopefully you will recognize that, within certain limits, taxes can be controlled to an economic advantage. The tax laws as now imposed are quite complex. Many of these laws and the regulations thereunder involve many factual determinations, technical considerations, and specialized valuations that can best be made by people trained in the specific area concerned. A substantial amount of a tax liability turns on the proper consideration given to issues involving facts and principles which are peculiarly engineering in nature. The importance of these "engineering" issues in tax administration has been significantly increased in recent years by our rapidly advancing technology, automation, stepped-up mineral and oil exploitation, new industries such as electronics and nuclear power, and the extension of percentage depletion to all minerals. These specialized requirements incorporated in the law are so technical that full consideration can not be given by people with a non-engineering background.

Jan 7, 1974

By John A. Shuster

INTRODUCTION Controlled ground freezing for mining and construction applications has been in use for over a century. Despite the great technological evolution which has occurred during this period, ground freezing is still used on projects today with much the same basic technology as that used originally over 100 years ago. Major developments have occurred in the separate fields of frozen soil mechanics, refrigeration, and heat transfer analysis. However, except for a few projects in Europe and Asia, these developments have not been combined to upgrade ground freezing techniques to their potential level. In view of this situation, it is believed desirable to examine the art of ground freezing in light of recent technical developments, together with highlights on some of the apparent advantages, disadvantages and economics of the various alternative approaches. The purpose of this paper is to attempt such an examination, with particular emphasis on the practical application of presently available technology. GENERAL ADVANTAGES AND DISADVANTAGES Ground freezing may be used in any soil or rock formation, regardless of structure, grain size or permeability; however, it is best suited to soft ground rather than rock conditions. Freezing may be used for any size, shape or depth of excavation and the same physical plant can be used from job to job despite wide variation in these factors.

Jan 1, 1997

By White B

A novel approach is suggested for the solution of planning and development problems in the coal, mining industry. The formation of coal measures depends to a significant extent on sequential geological processes and events which are probably best defined in a "system of processes and responses." The great number of variables in such a system is a characteristic feature of geological environments. Research work over the past two decades, in particular, has successfully established analytical procedures for the identification and definition of relevant and irrelevant variables for mining developments in specific geological situations. Such situations are typifiable within the regional geological setting of coal deposits. Scale gaps can be bridged by reliance on common symmetrical attributes and pervasive geometric features. Depositional processes and their resulting attributes are responsible for the development of mechanically significant rockmass "defects" and anisotropies; such features have to be identified and assessed for the selection of colliery design criteria. It is suggested that the procedural frame- work of systems engineering analysis is a most appropriate tool for the assessment of those geological features that can influence the mechanical behaviour of the "floor-seam-roof" system in "high technology" mining operations of the future. It is anticipated that the overall emphasis of future mining systems will be toward the use of larger scale more highly productive methods and machines, with higher capital outlay but

Jan 1, 1987