Search Documents

By Naiyang Ma

Along with steel production, various steelmaking slags are constantly generated at considerably high rates. In general, steelmaking slags are not categorized into hazardous materials and do not cause any environmental issues. Therefore, recycling of steelmaking slags is often aimed at creating values by using the slags to replace high-cost raw materials. Chemical compositions and particle size distributions of slag products from steelmaking slags will determine what raw materials the slag products can replace. Consequently, maximizing the values of steelmaking slags will require to produce slag products with the highest values and to process the slags with the lowest costs. In this paper, several slag processing processes are assessed based on maximization of the values of the steelmaking slags.

Mar 1, 2017

By Beatryz C. Mendes, Márcio Sampaio S. Moreira, Rita de C. S. S. Alvarenga, Juliano Correa

Over the last decades, modern technology to build wood structures have been substantially developed. Building solutions for floor systems of wood-concrete mixed T-beams with wood web and concrete flange stand out among these technologies. This work describes an experimental investigation of the performance of bond connectors made of round steel bars for wood-concrete mixed elements. Symmetric three-member specimens were built. The middle member was made of concrete and the other two were made of wood. The first kind of connector consisted of steel bar designed as straight pins with head, normally driven through the wood. The second kind consisted of arc-shaped connectors directly embedded into the wood or bonded using epoxy adhesive. The specimens were then tested in compression. The compressive strength and the force-displacement curve were obtained, in order to evaluate the failure mode and obtain the stiffness in the ultimate (Ku) and serviceability (Ks) limit states. The stiffness values were calculated in the interval corresponding to the secant straight line between, respectively, 10–40 and 10–70% of the ultimate strength. The obtained results indicate high strength and ductile failure mode for all of the cases. Bond stiffness gains were verified when using the arch-shaped connectors.

Mar 1, 2017

By Isadora Dias Perez, Monica M. Jimenez Correa, Jorge A. Soares Tenorio, Denise Crocce Romano Espinosa

The generation of mining waste has been the subject of environmental, economic and social concern. Alternative and sustainable methods of recycling metals technologies are desired. The present work focuses on the application of the ion exchange technique for the extraction of metals contained in a lateritic nickel mining effluent. The Purolite S950 chelating resin was used in the present work because it has the ability to adsorb transition metals present in an acidic solution. The experiments were carried out in a batch varying the pH in the range of 0.5–2.0. 1 g of resin was placed in contact with 50 mL of solution and stirred for 120 min at a speed of 200 rpm and temperature at 25 °C. The results demonstrated that the affinity of the resin varied with pH. The adsorbed metals were only copper, manganese, magnesium and zinc. The most extracted metal was copper, corresponding to 37%, when the solution was conditioned at pH 2.0.

Mar 1, 2018

By Shilai Yuan, Huimin Lu, Panpan Wang

A big andalusite ore bed was found in Dingxi District, Gansu, China. In this paper, the feasibility of producing solar grade silicon from aluminum-silicon alloys by carbothermal reduction of andalusite ore was studied. First, the carbothermal reduction experiments were conducted in a 100 kVA DC submerged arc furnace with reducing temperature 2000–2200 °C and reducing time 4 h, the hypereutectic aluminum-silicon alloys containing 50–55 mass% aluminum and 35–45 mass% silicon were obtained; then the investigation on solidification of the hypereutectic Al-Si melts under the temperature gradient as an intensified separation silicon way was carried out. According to previous investigation, the optimized technical process for solar grade silicon and eutectic Al-Si alloy from andalusite ore was proposed.

Mar 1, 2017

By Lina Ospino Ballesta, Oscar J. Restrepo Baena, Juan Diaz Martínez

Artisanal and small-scale underground gold mining in Colombia plays a significant role in the country’s economy, but it faces persistent occupational hazards that threaten worker safety. Despite mining economic contributions, outdated technologies, limited risk management practices, and insufficient regulatory enforcement have led to recurring workplace accidents, many of which have been fatal. This study presents a systematic review of mining-related accidents over the last decade. Through geo-referenced analysis, high-risk municipalities were identified, and the frequency of accidents was correlated with the mining legal status and operational practices of these municipalities. The findings underscore the urgent need for evidencebased interventions that are tailored to the country’s unique mining context. Ultimately, this research contributes to the global discourse on mining safety by highlighting practical pathways to reduce occupational risks and promote safer, healthier workplaces in resource-constrained environments.

Feb 22, 2026

By Shengli Wu, Feng Chang, Hua Lu, Jianliang Zhang

Kinetic studies of the blast furnace dust (BFD) reduction process have been carried out under non-isothermal conditions. BFD pellets were made with bentonite as the binder. A Comprehensive Thermal Analyzer (TG-DSC) was used to determine the mass loss of pellets, which were heated at three heating rates of 10, 20, 30 K/min up to 1493 K. Furthermore, the metallization rate and mineral composition of BFD pellets heated to several different temperatures were analyzed by chemical analysis and X-ray diffraction (XRD). It was found that, with its inherent carbon resources as the reducing agent, the metallization rate of BFD pellets could reach 88% at most. The reduction and weight loss process of iron oxides mainly happens above 1273 K. In addition, from application of the Coats-Redfern equation the apparent activation energy of the reduction from wustite to Fe was 443 kJ/mol and the mechanism was interface reaction R..

Mar 1, 2017

By Md. Z. Quadir, M. Ashraf, A. A. H. Ameri, J. P. Escobedo-Diaz

The quasi-static mechanical response of hot rolled lean duplex stainless steel 2101 (LDSS 2101) in rolling, transverse and normal directions under compression loading has been investigated for its perceived anisotropic behaviour. Microstructural characterization is performed by optical microscopy and Electron Back Scatter Diffraction (EBSD) to qualitatively define the influence of the texture by using Taylor factor and grain sizes, and phase boundaries by utilizing the modified Hall-Petch formula. It was observed that LDSS2101 does not show anisotropic behaviour in terms of the mechanical strength but it has a clear anisotropy in the lateral strains; the microstructural explanation of this response may result from the phase boundaries strengthening.

Mar 1, 2017

By Senlin Cui, In-ho Jung

Significant amount of commercial aircrafts will be retired in 2020, and the recycling of Al components in such aircrafts becomes an important issue in aerospace and Al industry. Recycling of Al from obsoleted Al products can effectively reduce the energy consumption and CO2 emission which is more economical and ecofriendly. In the present study, thermodynamic analysis for the various recycling technologies of Al alloys were performed based on the comprehensive and accurate thermodynamic database. The recycling technologies reviewed in this work include the vaporization process to reduce Zn, precipitation process to reduce Fe, Mn, Si, Ti, Zr, flux treatment for Al 2O3 and MgO, etc. Several key issues and limitation of the recycling of the aircraft Al were discussed. The recycling technologies discussed can also be utilized to recycle other Al alloys for common usage. All the thermodynamic calculations were performed using the FactSage FTlite database.

Mar 1, 2017

By TTE-Europe GmbH

A few years ago, the term Track & Trace for explosives was only known in Europe and Brazil at most; the introduction of this technology is experiencing an undreamt-of boom worldwide. More and more countries are enacting legislation to introduce Track & Trace of explosives and follow Europe and Brazil on this path. At present, the world's leading manufacturers are already using such solutions, are in the process of implementing them, or are in the planning process. However, based on the experience gained in Europe, there are outstanding challenges for all manufacturers. These are questions of compliance, logistics, distribution, and, of course, especially, the necessary adaptation of the production environment. However, this development involves considerable effort on the part of the manufacturers. New devices for marking the explosives and digitally recording the data are integrated into the production process. This should be done as cost-effectively as possible, without restricting production capacity and speed, and with as few process changes as possible. This paper uses real-life customer experiences examples to explain paths from project design to real implementation. Lessons learned from the experience of European explosives manufacturers are presented, missteps are described, and solutions are identified. Individual steps along this path are explained, and solutions are told to avoid pitfalls and bottlenecks. Finally, it refers to the risk analysis and concrete examples in implementing the planning into production. Methods of marking various explosives are shown, and the use of Track & Trace to solve logistics tasks in picking and shipping explosives, including the data exchange with ERP (Enterprise Resource Planning) systems.

Jan 26, 2026

By Naiyang Ma

Along with fast growth of EAF steelmaking, better ways of treating EAF dust have been continuously pursued for better environmental protection and better economic benefits. In this contribution, various ways of collecting EAF dust in EAF off-gas cleaning systems are reviewed, and generation of dust and concentration of zinc in the dust from various collecting devices are examined. Accordingly, recycling of EAF dust through source separation is discussed.

Mar 1, 2018

By Elizabeth Carvalho L. Cardoso, Ademar B. Lugão, Sandra R. Scagliusi

This research investigated how gamma-radiation affected PP/HMSPP structural foams filled with biodegradable synthetic polyester PLA in terms of thermal properties, biodegradability and infrared spectrum. Polymers are used in various applications providing enormous quantities of wastes in environment and contributing with 20–30% of total volume of solid residues. Besides, shortage of plastics resins obtained from fossil base is addressing research and development toward alternative materials; environmental concerning in litter reduction is being directed to renewable polymers for manufacturing of polymeric foams. Biodegradable polymers, a new generation of polymers produced from various natural resources, environmentally safe and friendly, can contribute for pollution reduction. PLA (poly(lactic) acid)) was chosen to be blended with PP/HMSPP. Blends thereof were subjected to gamma radiation at 50, 100, 150, 200 and 500 kGydoses.Soilburialtestpointedtowardapartialbiodegradationofirradiated PLA-PP/HMSPP foams; other characterizations involved TG/DTG technique and FTIR assessments.

Mar 1, 2017

By Monica M. Jimenez Correa, Jorge A. Soares Tenorio, Denise Crocce Romano Espinosa, Paula Aliprandini

The surface zone of nickel laterite ore is generally considered as residue. However, because of the depletion of ore sources and the increase in demand, this previously discarded zone may now be processed economically for nickel and cobalt. After leaching and removal of the impurities, the solution contains cobalt, magnesium, manganese and nickel. Solvent extraction is a hydrometallurgical technique used in the separation of metals from aqueous solutions. Cyanex 272 and D2EHPA are extractants used to separate nickel from cobalt. The mixture of extractants can change the performance during the metals extraction. This work aims to evaluate the solvent extraction of nickel and cobalt when Cyanex 272 and D2EHPA are mixed. The results showed that the increased concentration of D2EHPA in the organic phase increased the extraction of nickel and magnesium. However, cobalt extraction was reduced and the manganese extraction was not altered.

Mar 1, 2018

By R. Bishop, J. Baggett, J. Monsalve, N. Ripepi, A. Soni

Technology plays an ever-increasing role in improving the safety and efficiency of mining operations. Laser scanning and photogrammetry are two useful methods for capturing 3D digital representations of real world objects. While both technologies have been applied to the mining industry in numerous ways, the practical applications in an operating underground limestone mine has been tested for this paper, including for visualization and site characterization. Each technology is capable of creating highly detailed geospatial point clouds, but are all point clouds created equal? This paper presents a comparison of a laser scan and photogrammetry of a limestone pillar and addresses the strengths and limitations of each method for creating digital models of operating underground limestone mines. INTRODUCTION The United States crushed stone business is a ~$14 billion per year industry representing 1,430 companies which operate 3,782 mining operations across the 50 states. In 2017 alone, 1.33 billion tons of crushed stone was produced with 76% used predominately for road construction and repairs, but also for the production of cement, lime, chemical and agricultural uses. Over 70% of domestic crushed stone producers source their material from limestone and dolomite deposits, with currently only 82 mines (2%) operating underground (USGS, 2018). Underground mining requires a different technical skillset, and poses great challenges for production that must be both safe and economical. Therefore, there are many risks that an operation must mitigate in order to produce underground limestone. Some of the challenges in underground limestone mining involve geological hazards that are unique to the rest of the industry. The geologic features such as faults and weaknesses can be difficult to assess in a production environment (NIOSH, 1998). The consequences of failure due to improperly designed underground mining ground support systems, such as from a roof failure, are not only life threatening for the miners themselves, but can easily shut down an entire mining operation.

Jan 1, 2019

By T. M. Morris

G. L. Simard and D. J. Salley—The authors and ourselves" independently came to similar conclusions both as to the value of tracer methods for the study of flotation and the general nature of collector-mineral interaction. The dodecylamine-quartz system appears to be simpler than the dithiophosphate-galena one, and the results therefore appear clearer. It is evident from a comparison of the two papers, however, that care must be used in extending the results to other more complicated systems. In the case of dodecylamine-quartz, the possible influence of micelle formation is of interest. There is no a priori reason why complete monolayer formation should necessarily occur at the concentration for micelle formation, since sorption depends on the nature of the substrate as well as on the properties of the solute in solution which alone determine micelle formation. Indeed, the fact that the onset of increased adsorption, point B in fig. 2, occurs at a concentration one tenth the critical value for micelles might imply that micelle formation does not have an influence. Interestingly enough, the data may be handled by the methods used for multilayer adsorption of gases on surfaces. Thus, if the amount adsorbed is plotted versus concentration, a sigmoid type curve is obtained, similar in form to a so-called Type I1 isotherm13 generally attributed to multimolecular adsorption. A monolayer value of about 0.12 mg per g may be estimated from the knee of this isotherm. On the other hand, if a plot is made according to the multilayer gas equation for adsorption to an unrestricted number of layers, eq 38,13 assuming the critical micelle concentration as the saturation concentration, the data above 120 mg per liter fall on a straight line from which a monolayer adsorption of 0.3 mg per g results. These considerations suggest that the monolayer may occupy an area somewhat less than the geometric value of 0.4 mg per g, and that micelle formation may indeed be a factor in the adsorption. the angle between the solid-liquid and liquid-gas interfaces, measured through the liquid. The value of the equilibrium contact-angle is uniquely determined by the value of the interfacial energies of the three intersecting interfaces and is independent of other forces in the system. When the liquid-gas interface intersects the solid at an edge—as was the case for all the experiments reported in this paper—the orientation of the solid-liquid interface is indeterminate or varies through 90" for a right-angle edge. Mr. Morris has called the angle between the horizontal and the liquid-gas interface for this edge condition a "static contact-angle." I feel that this term is unnecessarily misleading. In the first place, "static contact-angle" sounds too much like "equilibrium contact-angle." In the second place, the magnitude of the "static contact-angle," which I would prefer to call the "supporting angle," is determined by the forces in the system other than those derived from the interfacial energies, hence "contact angle" is misleading. If Mr. Morris had said that the "supporting-angle" is variable and depends on the weight of the particle and size of the bubble and that it has a maximum possible value equal to the equilibrium contact-angle, his discussion would have been more accurate. T. M. Morris (author's reply)—Mr. Kellogg puts forth a reasonable criticism of some of the terminology used in the paper. I agree that the term "static contact angle" may be misleading. Substitution of the term "supporting angle" or "vector angle" may be more suitable. F. X. Tartaron—In this paper the author presents a very interesting mathematical development of the forces present when a mineral particle adheres to an air bubble. Excellent concordance is obtained between mathematical formulation and experimental results. It is the writer's understanding that when the mineral surface presented to an air bubble is greater than the area of contact, the maximum contact angle is obtained. However, this contact angle represents distortion of the bubble, the normal shape of which is spherical or in cross-section, circular. This distortion produces a force that acts in opposition to the force of adhesion between the bubble and particle. Hence, at maximum contact angle, the force of adhesion between bubble and particle is at a minimum for static conditions. However, when the size of bubble is increased, the size of particle remaining the same (and all other conditions remaining the same), the contact angle decreases, the distortion of the bubble decreases and the force in opposition to adherence of bubble and particle also decreases. Thus, there is stronger attachment between bubble and particle. When this situation is applied to actual flotation conditions, it is doubtful that it has any significance. The reason is that the bubbles are normally so much larger than the particles, that in substantially all cases, it is probable that negligible distortion of the bubble takes place. In table IV, the author makes computations for bubbles from 0.50 to 2 mm diam. This is from 0.02 in. to 0.08 in. Certainly the bubbles generated in a flotation machine are far larger than this. The surfaces of the author's bubbles range from 0.79 to 12.6 sq mm. The area of contact of the glass rod (0.15 mm diam) is 0.017 sq mm. Thus, ratio of bubble surface to mineral area of contact ranges from 47 to 741 in round numbers. If we take a %-in. diam bubble and a 65-mesh (0.208 mm) particle of cubical shape, the ratio of bubble surface to mineral area of contact is 2931. Mineral particles do not readily become attached to air bubbles. Taggart has shown that in pneumatic flotation machines collector-coated particles are only temporarily attached to bubbles. They keep falling off and down in the froth but at a delayed rate as compared with gangue. Spedden and Hannan's motion pictures confirm the difficulty of attaching particles to air bubbles. In the agitation froth process, according to Taggart, air is precipitated from the water selectively on to the collector-coated particles and these

Jan 1, 1951

By Daniel Saramak

"Issues concerning effectiveness of the high-pressure comminution process in technological circuits of copper ore treatment were presented in the paper. Crushing processes taking place in high-pressure grinding rolls devices (HPGR) are currently one of the most efficient methods of hard ore size reduction in terms of the energy consumption. The HPGR products are characterized by a fine particle size and the micro-cracks formation in individual particles, which appear in downstream grinding processes, decreasing their energy consumption. The purpose of this paper was to analyse the effectiveness of a ball mill grinding process depending on the changeable conditions of run for the HPGR crushing process. The research programme carried out included crushing tests in the laboratory scale HPGR device at various settings of the operating pressure volume and selected qualitative properties of the feed material (i.e. particle size distribution). Particle size distribution analyses of all HPGR products were performed and in the next stage the material was a feed to the ball mill grinding process. Grinding process kinetics were investigated through the determination of mass recoveries of individual particle size fractions after defined grinding time intervals. The models, defining the grinding process effectiveness as a function of changeable conditions of HPGR process run, were determined on the basis of obtained results. Based on these models the optimal grinding time in a ball mill was specified which is, in turn, the basis for optimization of operation of the technological comminution circuits for a given material type. The obtained results proved that the application of HPGR devices in a given copper ore comminution circuit may improve the effectiveness of the downstream grinding process which leads to improvement of the entire circuit work efficiency through decreasing the process energy consumption and enhancing product size reduction."

Jan 1, 2014

By J. D. McCain

Magma's San Manuel smelter has adopted new operating techniques resulting in 21% increased productivity and 87% reduction in lost time accidents. Reverberatory furnaces were converted to coal firing from expensive natural gas and fuel oil. Slag and matte flow problems and safety were improved by implementing hydraulic slag stopping and matte tapping machines. Coordination of furnaces, converters and acid plant was improved by using a computer-aided converter controller/scheduler function. Manual mudding of converter lips after each collar pull was replaced with a gunning system for coating the mouth castings. One converter punch car was automated using robotic technology. An automatic anode take-off was installed with fewer moving parts and a mechanism for ear twisting one cell contact. Anode copper refining was improved by replacing propane/hydrogen mixtures with high pressure/velocity natural gas tuyeres. Improved converter scheduling increased acid plant production 43% with more autothermal operation time. Six dedicated computers/microprocessors are utilized for automation, data acquisition, process monitoring and on-line air quality information for the Supplementary Control System.

Jan 1, 1983

By R. S. Wang

The flotation of pyrite which be pretreated by electrochemical ways under external controlled voltages in different pH is explored. The floatability of pyrite is increased indistinctively after being pretreated in acidic and xanthate environment; Whereas, it is increased obviously between 400~800 millivolt in alkaline and xanthate condition. The reason for higher recovery of pyrite is that oxida-tion reaction, which results in S0 and S02, takes place on its surface, and that ethyl xanthate is oxi-dized into dixanthogen. In the meantime, the kinetics and mechanism is also studied.

Jan 1, 2014

By J. Font

The RAF or copper fire refining process at the Caletones smelter of CodelcoChile consists of several pyrorefining stages that successively lowers the levels of S, Fe, Pb, As, Sb, Te, Se and to some extent 0 in the copper melt, allowing the production of high quality fire-refined copper of 99.93 % purity (RAF copper). This chemical feature of the RAF copper is only achieved by quite long processing times, and a considerable consumption of fluxes and fuels in the RAF vessels. The main goal of this study was to improve the RAF process performance by thermodynamic considerations and industrial scale tests, i.e., an in situ approach for the process as featured by intensive sampling, characterization and subsequent modifications. Thus, both theoretical and industrial data were derived, and based on kinetic and thermodynamic evaluations, a higher operational standard was achieved for the RAF process. These new operational practices allowed enhancing the overall economic of the RAF process, by reducing the time and operational costs, and consequently increasing the availability of the vessels.

Jan 1, 2007

By Steve Johnston, Mowafak Al-Jassim, Fei Yan, Omar Sidelkheir, Alain Blosse, Katherine Zaunbrecher

"Imaging techniques are applied to multi-crystalline silicon wafers and solar cells throughout the production process. Photoluminescence imaging, both band-to-band and defect-band, is used to characterize defects and wafer quality at all process steps. These steps include bricks sawn from ingots, wafer sawing, cleaning and texturing, emitter diffusion, edge isolation and glass removal, anti-reflective coating/passivation, and metallization of finished cells. Bricks, wafers, and cells can be imaged at a rate commensurate with in-line measurement, giving spatial information to characterize quality and defect content. Photoluminescence images on silicon bricks can be correlated to lifetime measured by photoconductive decay and could be used for high-resolution characterization of material before wafers are cut. The defect areas in as-cut wafers are compared to imaging results from electroluminescence and lock-in thermography, and cell parameters of near-neighbor finished cells, showing correlations to efficiency, open-circuit voltage, and short-circuit current.IntroductionImaging techniques can rapidly characterize material quality and defect density. Photoluminescence (PL) imaging can be applied to silicon from the brick level to all wafer process steps [1-8]. At the brick level, material thickness allows for measurement and correlation to lifetime where surface recombination effects are minimized [6, 7]. At the as-cut wafer level where thin unpassivated wafers prevent accurate lifetime assessment due to surfaces, defects can still be categorized and quantified to predict finished cell performance [3-5]. Defect regions can be identified by recombination-limited band-to-band PL or by defect-band emission [9-12]."

Jan 1, 2012

By G. F. Zhang

Yunnan mineral is a kind of containing Ta-Nb rare earth deposit, the most potential economic valuable element in it is Sc, and raw mineral has 17.0 g/t Sc. Take the character of Sc into account, the key problem in producing scandium chloride molten salt by adaptive technology is how to man-ufacturer anhydrous scandium chloride molten salt. During the course above, the key problem is that preventing Scandium chloride from being hy-drolyzed into ScOCl. The ScOCl content of molten salt not only affect purifying scandium but al-so do harm to the production of Mg-Al alloy. In order to restrain the creation of ScOCl, add ammo-nium chloride into molten salt. As long as ScOCl is created, it would be chloridized. Thus, during the course of dehydrating anhydrous chloride molten salt this method prevents scandium from hydrolyzing. Accordingly, the key phase of this producing course is eliminate ammonium chloride and the surplus crystal water, and the most crucial of it is restrain scandium chloride from being hydrolyzed into ScOCl. This research analyzed the theory that ammonium chloride is trend to be hydrolyzed into ammo-nium chloride, and propose the research scheme of restraining this process from creating ScOCl. The new process of restraining the generating of ScOCl and dehydration for crystal water rare earth chloride is adopted: Inert gas temperature increases rapidly to a certain degree to eliminate ammonium chloride and crystal water. The experimental research were done such as : the temperature of eliminating ammonium chloride and crystal water, amount of ammonium chloride, time, temperature growth speed, influence of inert gas flow toward to scandium percent hydrolysis, whereby, we conclude the optimal process condition in this period: Temperature: 400°C, proportion of oxidized scandium and ammonium chloride is 1:1.5(Proportion of oxidized scandium and additional salt is 1:5.4), time is 120minute, temperature growth speed is 10?/min inert gas flow is 5L/min.

Jan 1, 2014