Search Documents

By C J. Moran

The Gladstone region, as one of the most industrially intense regions in Australia, uses significant quantities of fresh water. Awoonga Dam, situated on the Boyne River, is the only major source of water in the region. The current typical annual usage is 53 GL (Porteous, 2006) and approximately 80 per cent of the water is used by heavy industry (Gladstone Area Water Board, 2004). Until relatively recently, there has been ready and easy access to raw water for industrial use. The recent drought, which resulted in severe water restrictions in 2002 and 2003, emphasised the importance of water for a dominant industrial region like Gladstone. Although now in the process of changing, the typical contractual arrangements in the past have provided little financial incentive for efficient water use. From research undertaken on potential water reuse opportunities, several key questions have emerged related to water management in an industrial region such as Gladstone. This paper highlights these key questions, presents findings from recent regional strategies and assesses the potential for water reuse. Even though there is no clear-cut financial incentive for reusing water, there could be stronger regional and risk mitigation drivers for doing so. Initiatives to incorporate adaptive capacity through collaborative industrial synergies would allow for robustness and resilience in water security, leading to long-term sustainable water management across the Gladstone region.

Jan 1, 2006

By Steven M. Bishoff

The reclamation of surface land areas disturbed during the course of coal recovery became a major, universal consideration upon the implementation of the Surface Mining Control and Reclamation Act of 1977. This legislation not only established reclamation as an absolute requirement, but also presented guidelines for reclamation standards and required bond-posting procedures to assure completion of the reclamation process. The Office of Surface Mining was established to enforce the provisions of the Congressional mandate by promulgating specifically detailed regulations and supervising the State participation in this regulatory process. The major operational consequences of the reclamation-related provisions of the Act and the OSM regulations are the increased costs and complex procedures necessary to accommodate the regulatory authorities. It is anticipated that many of these costs and procedures have not been adequately evaluated by either the coal operators or the regulatory bodies. It is, therefore, necessary to proceed with an examination of the general reclamation processes, the effect of these processes on product costs, and the methods, if any, which may be utilized to minimize their impact on the overall operation.

Jan 1, 1981

By H. William Zeller

The U.S. Bureau of Mines evaluated the effects of two iron-based fuel additives on diesel particulate matter (DPM) emissions. The 5.6-L, six-cylinder test engine is typical of engines used in underground mines. One additive, ferrous picrate, did not measurably affect exhaust emissions. This report is mainly about a ferrocene-based additive that reduced DPM between 4 and 45 pet., depending on engine operating conditions. The report concludes that the DPM reductions were caused by the catalytic oxidation properties of a ferric oxide coating that developed inside the engine's combustion chamber. The ferric oxide coating also decreased gas-phase hydrocarbons and O2, but it increased CO2 and NOx, The increase in NOx, of about 12 pet, is considered the only adverse effect of the ferrocene-based fuel additive. The results suggest that the effectiveness of ferrocene was partially offset by increased sulfates because of the high-sulfur fuel used. Recommendations for continuing fuel additive research are presented.

Jan 1, 2010

By Q. X. Li

The state discharge standard for arsenic-containing wastewater which is the first kind of pollution is less than 0.5 mg/L. In fact, in a certain company, the acidic arsenic-containing wastewater in non-ferrous smelting was as high as 860 mg/L, which is far beyond the state discharge standard. Obviously, the direct release of this wastewater without further treatment would result in great hazards to the ecological environment. To aim directly at the characteristics of acidic arsenic-containing wastewater, in this study, two steps of treatment including oxidation-flocculation and removal fluoride by mixing alkaline neutralization were suggested. Through analyzing various influencing factors in treatment effects, the optimum technical conditions were obtained. The sediments after treating were recyclable and the secondary pollutions can be avoided. Moreover, the results also show that, all indexes of the effluent after treating are lower than the First Grade Standard of Integrated Wastewater Discharge (GB 8978-1996). This novel method has advantages of short flow sheet, easy operation and low cost.

Jan 1, 2014

By K. L. Bainbridge

This report describes the results of a study to determine which types of, and to what extent, mining wastes can contaminate groundwater through leaching of acid-forming or potentially toxic constituents. The primary focus of this study was on coal mining wastes, especially overburden spoils and preparation plant refuse. In addition, the potential for contamination by leachates from clean coal stockpiles was also examined. The study approach included investigation of (a) the amounts and geographic locations of mining wastes in the United States; (b) the chemical character of mining wastes, especially with regard to potentially acid-firming or toxic constituents; and (c) the extent to which acid and/or toxic components are leached from mining wastes by rainwater. To evaluate the leachability of coal wastes, a laboratory waste leaching method was developed during this study to specifically simulate the leaching process over a long-term. Waste samples collected during this study were also leached by the EPA extraction procedure and ASTM waste leaching method. Results of the three leach test methods were compared to evaluate their relative capabilities to predict the leachability of mining wastes.

Jan 1, 1980

By Mason L. Dicks

For many years The Hanna Mining Company has been investigating the flotation of the non-magnetic iron ores located in the Western Mesabi Range of Minnesota.1 During the 1950's a number of anionic iron procedures were evaluated and in the late 1950's and early 1960's the anionic silica floats and the cationic silica floats were tested with improved results.2 The cationic float became more attractive and effective by the use of the improved ether amines. About 1962 a desliming process by selective flocculation was developed by the U.S. Bureau of Hines at Minneapolis', Minnesota.3, 4, 5 This is a very efficient method of desliming and was first tried with the anionic silica float and then the more practical cationic silica float. In the mid 1960's The Hanna Research Laboratory began studies to optimize the selective flocculation process for our ores. This was followed by studies to optimize the cationic silica float after desliming by selective flocculation. This testwork was done on large, 500 to 1000 tonne bulk samples of oxidized taconite which were later successfully piloted at .68t/h (1500 Lbs. /hr.). A program was then begun to test the oxidized portions of numerous taconite drill holes to outline the ore bodies and develop mining plans. This paper will discuss our optimization results of both the selective flocculation and the cationic silica float as applied to our various ores. In addition the pilot plant studies and drill core testwork will be discussed.

Jan 1, 1978

By Richard A. Thomas, Connor B. Brown, Thomas H. Dubaniewicz, Teresa Barone

Electric vehicles powered by lithium-ion (Li-ion) batteries are being developed by mining vehicle manufacturers as a replacement for diesel-powered vehicles. Explosion-proof (XP) enclosures are frequently employed to enclose electrical ignition sources in gaseous underground mines to prevent the spread of an internal methane-air explosion to a nearby explosive atmosphere. Due to thermal runaway (TR), Li-ion batteries have the potential to cause pressurized explosions in an enclosed structure. Past research has shown the potential for well-confined Li-ion cell TR to drive pressures beyond the conventional pressure specification for XP enclosures. Researchers at the National Institute for Occupational Safety and Health (NIOSH) used an Accelerating Rate Calorimeter (ARC) to induce thermal runaway of Lithium Titanate or Lithium Titanium Oxide (LTO) type 18650 cells enclosed within containers with various volumes and found an inverse power relationship between the TR pressure and available free space. The results were similar in magnitude to that of lithium iron phosphate (LFP) cells, which were used in prior testing. Temperatures, gas amounts, and TR pressure-rise rates were also recorded. The data indicate that with enough free space, the pressures can be lowered below the conventional pressure specification for XP enclosures.

Feb 1, 2024

By Steven McCutcheon

As most of us have learned through prior and often frustrating experience, anyone proposing to construct a new or expanded mining-ore processing facility must first contend with a rather complex array of environmental laws and permitting regulations administered by a number of different Federal, State and local agencies. At our lost count, there were about 55 federal enactments affecting base and precious metals projects. Applicable State and local laws will usually increase that number significantly. The time and costs associated with complying with all these various regulatory programs usually constitutes one of the major areas of uncertainty in the development of a proposed project. There are many in the mining industry who firmly believe that these environmental regulation and permit programs necessarily causes significant delays and increased costs in the development of a project. This belief, unfortunately, is probably a result of a basic misunderstanding of how the environmental permitting and regulatory system actually works.

Jan 1, 1984

In terms of throughput, product size and power draw, grindcurves provide a measure of the response of the mill performance to changes in mill operating parameters ? usually mill filling. Since presenting the principle in 2006, grindcurves have been applied to a wide variety of AG and SAG mills. Mill response has been carefully measured for variations in: mill fillings from 15% to 40%; throughput by a factor of two; power by 50%; feed blends; liner profile; and mill speed from 65% to 80%. The outcomes of this extensive program of work are presented as the measured grindcurves. How they have enhanced our understanding of mill operation and how they may be applied to practical daily mill control is discussed. It is proposed that this technique provides a viable and valuable mill control tool that may find extensive application in the industry.

Jan 1, 2012

By John V. Beall

A completed feasibility study executed by an independent agency can benefit a company in two ways. Inside the organization, it verifies the project staffs ideas and their concept of the facility. Outside the company, it can be utilized to obtain equity partners, debt financing, and other forms of credit. It is advisable to bring in a project execution contractor for the feasibility study. A project execution contractor is able to work with engineers to develop the project concept, process flowsheet, and best utilization of the site. By getting an early start on understanding a company's policies and working methods, a project execution contractor saves the company money since it does not have to go through the educational buildup twice. The contractor is a specialist in putting together a bankable document that can be taken to a financing source. It answers all the agency requirements on the first pass. In addition, the contractor can advise an owner on likely financing sources since he works on the worldwide market every day. A less obvious advantage of including the contractor in the study and predevelopment buildup stages is the importance of coordinating finance and technical input. The financing source influences equipment specifications, procurement, logistics, project schedule, cash flow, and liquidity. There are many surprises in store for any manager of a large international project involving worldwide financing and purchasing. The job does not have to be made more difficult by bringing in a contractor after all predevelopment steps are taken. The contractor can still work if the predevelopment steps have been done, even if he does not agree with them. But early contractor involvement is the preferable solution.

Jan 10, 1980

By T. J. McKeon

Gravity separators such as spirals are commonly used in multistage cleaning and scavenging circuits to improve the quality and recovery of concentrates produced in the industrial minerals industry. Unfortunately, field surveys suggest that many industrial operations are poorly configured in terms of equipment layout. This shortcoming can often be attributed to a failure by engineers to make use of fundamental process engineering tools for circuit design. One of the most important of these is linear circuit analysis. This powerful tool makes it possible to mathematically compare the relative efficiency of circuit configurations in advance of experimental testing. This article provides a basic review of the linear circuit analysis concept and discusses some of the key insights it provides for the layout of multistage circuits. An industrial case study is provided to show the tremendous impact that this process engineering tool can have on the design of multistage spiral circuits in a heavy mineral wet plant.

Feb 1, 2012

A series of petrological studies were carried out on the characteristics of alteration and mineralisation in mainly structural-controlled (Deep Star, Meikle, Deep Post) and predominantly lithological-controlled (Post-Betze-Screamer and West Leeville) gold deposits in the northern district of the Carlin trend, Nevada. Alteration and mineralisation in these deposits are hosted in a sequence of calcareous clastic units of the Devonian Popovich Formation, into which have been emplaced a number of Jurassic intrusions, and syn- to post-mineral Eocene dikes. Four hydrothermal events have been recognised in these deposits: an initial Devonian base metal system and early diagenesis; a Mississippian stage of alteration in conjunction with burial metamorphism; contact and hydrothermal alteration and base metal-gold mineralisation associated with the emplacement of the Jurassic intrusions; and a Carlin-style gold system related to Eocene magmatism.

Jan 1, 2004

By Peter F. Pullen

The need to apply the latest available technology to develop better tools and methods to meet problems in the mining industry was recognized by six of Canada's leading mining companies. As a result, MIROC (Mining Industry Research Organization of Canada) was chartered to identify problem areas in Canadian mining and to have research carried out to develop the tools and equipment to meet these perceived needs. The initial activity of MIROC has been in the environmental field, with improved clothing and protective devices being developed by contractors. Work clothing for miners is now being field tested. Respiratory protection and a new personal light source combined in a new "space-age" helmet are about to be issued for testing. Further developmental work is being carried on to offer these units and probably other personal protective devices on an individual basis as well as in a combined package.

Jan 1, 1979

By Robert F. Mehl

PROGRESS in the general field of nonferrous physical metallurgy during the past .year has been uneventful but healthy. A continued increase is apparent in the number of useful alloys and in the mechanical treatment and heat- treatment of finished metals and alloys nothing can hinder the multiplication of alloys or the diversification of their treatment as knowledge of the behavior of .alloys increases; as ternary and quaternary alloys are better understood, hundreds of new metal combinations with unusual properties may well be expected. Evidence of rapid progress is already at hand.

Jan 1, 1936

By J. J. Liu

In the Bayer process, control of alumina trihydrate particle size, oxalate stability and morphology and foaming is crucial for improving the yield and quality of alumina trihydrate. One way to economically achieve such control is to employ specifically developed chemical additives, termed, crystal growth modifiers (CGM?s). In this paper, the mechanism of action and practical application of CGM?s in the Bayer process are summarized. The application of CGM additives allows for both enhanced agglomeration and secondary nucleation control, and hence coarsening of the particles. Current research efforts have utilized the information gained from mechanistic studies to enhance the performance of CGM products. It was demonstrated in both laboratory tests and industrial operations that the newly developed CGM formulations have a range of properties with enhanced performance, compared to the current commercial products.

Jan 1, 2014

By G Phillips

The Merlin project is situated 130 km south of Cloncurry in North West Queensland, Australia. It is located within the Pre-Cambrian Mt Isa Inlier and is grouped within the Eastern Fold Belt. The host rocks are metasedimentary rocks of the Proterozoic Kuridala and Staveley Formations adjacent to the Mount Dore Granite.Merlin zone represents part of the Mount Dore polymetallic deposit containing copper, zinc, silver, gold, lead, cobalt and most recently has been found to host molybdenum mineralisation. This is intimately associated with economic grades of rhenium, a naturally occurring metal that is an important component of high temperature aircraft engines. The host rock sequence is a 200 m thick zone of metasediments sandwiched between competent granite in the hanging wall and brittle quartzite in the foot wall. A distinct shear marks the contact between the granite and metasediments. The host rocks are comprised of three main rock types: black shale, phyllite and altered banded calc-silicate.Mineralisation dips to the east at approximately 45° in a package of fine grained pelites and banded calc-silicates. The top 150 m of the sequence is typified by black shale and phyllite. The lower 50 m is typified by pink banded calc-silicate. The main molybdenite zone is located at and parallel to the pelite-calc-silicate contact. Down dip, the zone splits into two or three veins hosted by the calc-silicate rock suite and haloed by thin, steep dipping, stylolitic molybdenite veinlets.The deposit was discovered in 2008 by routine infill reverse circulation sampling conducted for the Mount Dore copper deposit. One hole penetrated below the main target Cu horizon and intersected visible molybdenite. During 2009 and 2010 a 50 × 50 m diamond drill pattern delineated a total mineral resource of 6.7 Mt @ 1.3 per cent Mo, 23g/t Re, 0.3 per cent Cu (mostly Indicated Mineral Resource with minor Inferred Mineral Resource). The resource has been estimated using ordinary kriging within grade domains. Access to the deposit has commenced via a decline and production through the nearby Osborne flotation concentrator (70 km south) is expected in 2012. All facilities and resources are fully owned and operated by Ivanhoe Australia Limited, a public listed company on the Australian and Toronto stock exchanges.

Aug 22, 2011

By J. Muralha, L. Lamas

"Given the results of triaixial tests, regressions are commonly used to evaluate the parameters of failure criteria that model intact rock strength and to perform statistical inferences used to evaluate characteristic values defined in EC7. Statistical robustness of these inferences is affected if the basic hypothesis underlying regression are not met, namely homoscedasticity (constant variance of the errors). This paper presents analyses of 23 sets of triaxial tests, starting by the evaluation of the regression parameters of the Mohr-Coulomb linear criterion and of the Hoek-Brown non-linear criterion, followed by carrying several statistical tests to check the homoscedasticity null hypothesis of independence between the variance of intact rock strength and the confining stress.INTRODUCTIONThough rock engineering design is clearly included in the scope of Eurocode 7(EN1997-1), its implementation raised a wide discussion regarding the applicability of structural safety concepts to geotechnical design of construction works in or on rock masses. The basis of the limit state design philosophy adopted in EC7 is that, for each particular design situation, all the possible limit states for a structure, or part of it, shall be considered and that it shall be demonstrated that the likelihood of any limit state being exceeded is sufficiently small. Though EC7 allows the limit states to be verified by one or a combination of methods, use of calculations is by far the most used, and it is often confused with the EC7 itself. It involves using characteristic values of actions, ground properties and geometrical data, as well as obtaining their design values by the partial factor method.Characteristic value of a given material property is defined in Eurocode (EN 1990) as: “value of a material or product property having a prescribed probability of not being attained in a hypothetical unlimited test series. This value generally corresponds to a specified fractile of the assumed statistical distribution of the particular property of the material or product”. As regards the design value of a material or product property, according to the Eurocode it is a “value obtained by dividing the characteristic value by a partial factor”."

Jan 1, 2015

By Merrill Steve, Dabrowsli Bartosz, Law Harrison, Taggart Diane, Christodoulou Lance

The capability to enhance flotation performance is a continuous pursuit in the mineral processing industry. Incremental improvements are being pursued by incorporating design changes into established flotation technologies. The industry, however, is demanding advanced technologies to perform better in terms of improved resource utilization while at the same time ensuring that power and water usage is reduced. To meet these demands, it is necessary to make a step change in the performance capability of flotation equipment.

Sep 30, 2022

By Harry Wilton-Clark

Introduction Coal cleaning may be taken as meaning the separation of coal-as-mined into two or more fractions. Coal cleaning includes coal washing, together with any other means used in the ultimate preparation of coal prior to shipment (as coal) . The method of coal cleaning devised for any given mine must be one which is based entirely on the economic results obtainable. The installation of a high-cost and complex washing plant, designed to produce a low-ash dean coal, at the highest possible recovery, may be unsound practice. A crude 'roughing' washer may be the best result of sound engineering and operating consideration, and in some cases coal cleaning should be confined entirely to preparation at the face. Consideration of complete costs, to the point where the coal is actually sold, may show that certain seams are workable or not workable. Of the seams found workable, extraction of the whole or parts of the seam may be decided on. The portion to be extracted may contain rock or bone partings, which must be removed. It may be good practice to mine the extra portion and remove the objectionable materials by surface washing; or it may be that such materials should be removed underground, even at an increased mining cost. For instance, in some of the steeply pitching seams of the Alberta Crow's Nest Pass district, the removal of bone and rock at the face may be almost impossible under the usual 'up the pitch' or 'angle' mining methods, but possible by mining across the pitch so that the material to be rejected can be removed and gobbed. Again, if a complete seam is being extracted, investigation may show marked differences between top coal and bench coal, and if sufficient mine cars are being loaded from a chute at one time, the fact that such a place is working top or bench coal at the time may be reflected by peaks in ash content or size proportions at the ripple. It may be very effective coal preparation to smooth out such peaks.

Jan 1, 1934

By Helmut Attlfellner

The selection of the best process for the oxygen generator for a metallurgical process requires the determination of all aspects which impact the economics of this facility. Concepts and features of modern air separation plants will be presented based on installed facilities for various metallurgical processes. The special features of advanced automation' of oxygen generators with load following and optimization of power consumption, automatic restart and unattended remote controlled operation will be investigated.

Jan 1, 1992