Search Documents

By Nicholas Kyriazi, John P. Shubilla

A joint effort by the U.S. Bureau of Mines (USBM) and the US. Mine Safety and Health Administration (MSHA) was undertaken to determine how well self-contained self-rescuers (SCSR's), deployed in accordance with Federal regulations (30 CFR 75.1714), held up in the underground environment with regard to both physical damage and aging. This report presents findings regarding laboratory-tested SCSR's in the fourth phase of testing from 1989 to 1993. The SCSRYs were tested on human subjects and on a breathing and metabolic simulator (BMS). These results indicate that most of the apparatus, if they pass their inspection criteria, perform as expected except units with manufacturing defects. However, when the apparatus are carried in and out of the mine daily and stored at the working section, they may suffer abuse. Physical signs of abuse, unless extremely obvious, are frequently not detected by the miners or mine operators. In addition, some apparatus collected for this study had not been returned to the manufacturer in a recall effort for correction of a manufacturing defect. In both cases, the apparatus would have presented problems in emergency use. Recommendations include improved training in inspection procedures and better enforcement of recall notices.

Jan 1, 1994

By T. Sterry Hunt

WET processes for the extraction of copper from its ores have of late attracted much attention, especially in Europe, where the use of oupriferous iron-pyrites as a' source of sulphur prevails. These processes present an additional interest, when, as is often the case, the copper-ore's to be treated contain one or both of the precious metals, since the complete separation of these from copper, either in the dry or the moist way, is, as is well known, one of the difficult problems of metallurgy. The principal wet processes hitherto in use for the extraction of copper from its ores, may be included under three classes : I. Those in which the copper in snlphuretted ores is rendered soluble in water by calcining them, after a preliminary roasting which removes the greater part of their sulphur, with a portion of common salt, by which the copper is converted into a chloride (Long-maid and Henderson), or with sulphate of soda, by which sulphate of copper is formed (Monnier). Allied to these is the method by which a portion of the copper is got as soluble sulphate by roasting without addition, a process which is sometimes modified and rendered more complete by re-roasting the lixiviated residues with the addition of a portion of raw sulphuretted ore (Bankart). II. Those methods in which free chlorhydric or sulphuric acid is used to dissolve the copper- from oxidized or roasted ores. These, while simple and efficient, are too costly, except in certain localities where chlorhydric acid is a waste product. Related to them is the plan which consists in exposing the oxidized and moistened ores to the slow action of sulphurous acid mixed with air, by which a soluble sulphate of copper is formed. It has been proposed to decompose the solutions of sulphate or chloride of copper by sulphuretted hydrogen, thus separating the copper as sulphide, and using the liberated acid to dissolve fresh portions of oxidized copper. It is, however, the almost universal practice to throw down the copper from its solutions, however obtained, in the metallic state by the use of iron, either scrap-iron or iron-sponge; although in some instances

Jan 1, 1882

By Robert D. Perry

This report describes methods of reclaiming abandoned or inactive tailings ponds and dams. The investigated sites were selected tailings deposits adjacent to metal mines in the southwestern United States and the Pacific Northwest. The basic data developed for each site consisted of the following: a review of existing literature; a site visit that included sampling of the tailings and surrounding materials; laboratory and engineering studies; and development of reclamation plans. Laboratory tests determined the gold and silver content of each tailings deposit and the chemistry of the tailings and surrounding materials. Reclamation plans that include approximate costs were developed for five tailings deposit sites. These ranged in size from 52,000 to 103,000,000 tons. Our conclusions on the remining potential of each site are based on the tailings assay and other technical data. This study concludes that remining as a reclamation tool is feasible at certain sites. Included in this report is a remining program as part of the overall reclamation plan for two sites. Our preliminary results indicate that remining as a reclamation tool is feasible for only one of them.

Jan 1, 1981

By R. Roufail

Mineral exploration is in a race to employ drilling technology that can perform the exploration and drilling investigation in a fast and inexpensive manner. After an extensive study of the available drilling technologies in the market, coiled tubing was chosen as a tool to be employed for mineral exploration due to its flexible mobility and ease of operation with a minimum number of personnel. Since coiled tubing technology is primarily used in the oil and gas industry, it was important to re-design the coiled tube rig to drill hard rocks in a fast and feasible manner. The main requirements were to drill the smallest feasible hole diameter and go as deep in the ground as possible, in the shortest reasonable time. The drilled rock particles, cuttings, are to be collected and analysed at the surface for their metal mineral contents. The process also needs to be repeated multiple times at different locations for mapping, without the need to change the tube on the rig due to failure or potential failure. The focus of the new designed coiled tube, for drilling and mineral exploration, is three fold. First is to increase the rate of penetration in drilling by designing a small high speed turbo motor. Second is to determine the controlling parameters of cuttings transport to effectively lift the cuttings to the surface for analysis and third is to minimize the overall weight of the rig for manoeuvring and prolong the life span of the coiled tube string. In this paper, a small downhole turbo motor, 5cm outer diameter, is designed to achieve a rotation speed of up to 10,000 rpm to fit on a small bit, coiled tube drilling assembly. The motor design utilised multiple finite volume and finite element analysis softwares for fluid flow study and fluid structural interaction analysis. The paper is also introducing the concept of a flow slurry loop that is designed to lift the cutting particles to the surface for mineralisation analysis. The controlling parameters of the cuttings transportation are the particle?s physical properties such as size, density, concentration and shape, as well as the rheological properties of the carrying fluid, drilled hole angle, as well as the fluid flow rate and flow dynamics within the annulus gap between the coiled tube and drilled hole. Such parameters are addressed via experimental work as well as numerical analysis. The paper is also presenting the selection and testing procedure of the material type for the coiled tube string. The tube needs to be light in weight for overall rig weight and its transportability. The tube is also required to drill several dozens of investigation holes before failing due to fatigue. A fatigue bending machine is designed to test the endurance limit of candidate materials for coiled tube strings and a performance index methodology is followed for material selection of the optimum material. The coiled tube rig is designed to be light in weight for transportation and relocation. It is also required to speed the drilling operation with the minimum footprint and reclaim the drilled rock particles for mineral composition analysis at the surface.

Aug 1, 2013

By M Stephens, T A. Sutra

Currently, there are several open pit mines with production rates of about 200 000 tpd of ore that are reaching the end of their economic lives. In most cases, the remaining orebody extends to depths greater than 300 m below the pit limit, leaving hundreds of millions of tons of reserves that can only be recovered by means of an underground mining method. One such method used for mass production is block caving. This paper presents a ventilation system for a four-zone block cave mine operation developed on a footprint 1000 m wide and 1200 m long. The system is designed for a mine with a nominal production rate of 120 000 tpd of ore using diesel powered units on the production and reduction levels. It discusses the air quantity requirements for the worst case scenario, which is anticipated to occur five years after the mine has reached its full production capacity. Finally, it summarises the results of computer modelling exercises that were carried out to determine an economic ventilation infrastructure that includes shafts, drifts, main fans, and ventilation control devices.

Jan 1, 2005

By N. Wahl, D. M. Blackketter, R. Thornton

This paper evaluated using a water-filled abandoned mine (Orphan Boy) as a heat source for a 240- kW closed-loop heat pump with the goal of heating a 2,000-m2 building. The mine has a 245-m vertical shaft connected to a large stope by three horizontal cross-cut shafts. There is 1,250 x 106 L of water at a consistent temperature of 24-26° C that is available mostly in the stope. The only heat exchanger placement option is in the vertical shaft. Therefore, the focus was to model heat exchanger placement in the vertical shaft to determine the extent to which the systems will induce thermal currents between the stope and vertical shaft. Modeling of thermal currents, temperature profiles and heat contribution from the ground was done using finite difference and computational fluid dynamics. An optimal configuration was determined showing sufficient water movement and heat transfer will occur with a low water temperature in the shaft above 20° C. This project supports a U.S. Department of Energy (DOE) grant that will implement the full-scale system.

Jan 1, 2013

By Margaret R. Egan

The U.S. Bureau of Mines conducted experiments in the intermediate-scale fire tunnel to assess the influence of air velocity on the gas production and smoke characteristics during smoldering and flaming combustion of Pittsburgh seam coal and its impact on the detection of the combustion products. On-line determinations of mass and number of smoke particles, light transmission, and various gas concentrations were made. From these experimental values, generation rates, heat-release rates, production constants, particle sizes, obscuration rates, and optical densities were calculated. Ventilation has a direct effect on fire detection and development. The results indicate that, in general, increased air velocity lengthened the onset of smoke and flaming ignition, increased the fire intensity, but decreased the gas and smoke concentrations. Increased air velocity also lengthened the response times of all the fire sensors tested. Rapid and reliable detector response at this most crucial stage of fire development can increase the possibility that appropriate miner response (fire suppression tactics or evacuation) can be completed before toxic smoke spreads throughout the mine.

Jan 1, 2010

By Eldridge Haynes

IF you ask the average American to define 'total war' he is apt to fumble for an answer. But in Britain everyone knows the answer, because Britain has mobilized its total labour force, including women. If we were to match, proportionately to our population, Britain's mobilization of labour, we should have 60,000,000 people working full time in the armed services, civilian defence, and war industries. Actually we have fewer than 35,000,000 so employed. In Britain two out of every three persons between the ages of fourteen and sixty-five are so engaged. For the first time in the history of any democracy Britain conscripts women for service in the army, navy, and air force. Two hundred thousand British women have been conscripted for the army, known as ATS, meaning Auxiliary Territorial Service. There are more women in the air force than the total personnel of the RAF at the outbreak of the war and almost all of the land base jobs of the British navy are now handled by women. In addition to cooking and office work, Britain's women soldiers and sailors are driving trucks and motorcycles, repairing motor vehicles, packing and repacking parachutes, installing, inspecting, and maintaining gun equipment and ammunition of combat planes after each raid, raising and lowering barrage balloons, forecasting weather, manning harbour craft, sending and receiving radio messages. A normal ack-ack unit is composed of 229 women and 189 men. The women man the gun height finders and predictors, give bearings, and signal to fire.

Jan 1, 1942

By Edwin S. Secor

The Federal Bureau of Mines conducted a field survey of 153 bituminous coal strip and auger mines to estimate coal recovery from surface mines in the Eastern United States. Recovery was calculated from field data by measuring coal losses resulting from mining coal and leaving barriers. Mean total recovery for strip mining in States east of the Mississippi River was 83.0 percent and ranged from 72.3 percent for Tennessee to 91.3 percent for Maryland. Mining losses and barrier losses were 10.1 and 7.7 percent, with standard deviations of 4.8 and 10.4 percent, respectively, indicating that barrier losses, although less than mining losses, were more variable. Mean total coal recovery varied only slightly for the two regions studied; 82.7 percent for Appalachia and 84.3 for the Midwest. Total recovery grouped by mining method--contour, area, and mountaintop removal--was 79.8,84.7, and 85.3 percent, respectively. Mean auger recovery was 35.9 percent; of the total average loss of 64.1 percent, over one-half resulted from design limitations while the remainder was attributed to operating losses. The wide recovery range at individual mines indicates the variability of the eastern surface coal mining industry. Because of this, care should be exercised in applying the results of this report to reserve estimates other than those of a general nature.

Jan 1, 1977

By Joseph J. Wallace

1. From the standpoint of known recoverable reserves, the following is the order of importance of the beds: Upper Kittaoning, Lower Kittanning, Upper Freeport, Lower Freeport, Middle Kittaning, Clarion, Pittsburgh, and Redstone. 2. mown measured and indicated reserves in all beds, based on a minimum thickness of 14 inches and on 1,800 tons per acre-foot of coal in place, me estimated at 1,859 million short tons as of January 1, 1952. Of this, 1,351 million short tons me in beds 28 inches and more thick. Areas in each bed were omitted from the estimates because available data relative to the bed characteristics are too meager to make an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1953

By M. E. Tyrrell

Despits its high melting point (2,135° C.), resistance to attack by molten metals, and its hardness (8), spinel (MgO?Al203) synthesized by the fusion of alumina (Al 2 0.) and magnesia (MgO) is not used on a large scale as a commercial furnace lining, mainly because of the prohibitive cost. This investigation by the Federal Bureau of Mines was prompted by the possibility of producing synthetic spinel from inexpensive raw materials by methods outlined in U.S. Patent 2,029,773, "Process for Obtaining Products Containing Spinets," dated February 4, 1936. In this patent Ture B. Haglund described a process for recovering crystalline spinels from melts in the system Mg0?Al203-2CaO-SiO2, a system well suited to the use of starting materials such as dolomite CaMg(C03)2, olivine [2(Mg?Fe)0.Si02], and bauxite (Al203?2H20) which are abundant in the southeastern United States. Compositions, ranging from a low content in the eutectic mixture of 35 percent spinal and 65 percent dicalcium silicate (2 CaO?SiO2) to a high of 75 percent spinel and 25 percent dicalcium silicate, were fused in electric furnaces of the arc-resistance and internal-resistance types. So long as members of the system were in proper chemical balance, "dusting" slags could be produced over the entire range of spinel concentration.

Jan 1, 1961

By S Azam

Coal is a vital energy source and source of carbon for metallurgical applications, contributing significantly to the world economy. Coal mining and processing involve multiple processes that generate Respirable Coal Mine Dust (RCMD), one of the primary sources of health hazards for coal workers. Since 2000, the rate of Coal Workers’ Pneumoconiosis (CWP) has continually increased in the U.S, with severity of the cases also worsening. Increasing evidence shows that exposure to RCMD in coal workers is a high-risk factor for lung cancer, which causes more deaths than the following three major cancers combined in the US Recent observations show an increased incidenceof CWP or other lung diseases, particularly among young miners in the Appalachian basin. The CWP prevalence in Appalachia is four times higher than the national average. Although various regulations are in place, the resurgence of such disease among coalminers demands additional efforts to better understand all the possible facets of coal dust toxicity, taking insights from current interdisciplinaryresearch efforts. One such important field is the interaction of coal dust with moisture in underground mines. Although moisture is prevalent and dynamic in an underground mining environment, it has never been evaluated for its impact on modifying the toxicity of coal dust and transport or flow behaviour. However, research conducted in atmospheric sciences in the past decade makes it clear that moisture in the atmosphere can significantly alter the behaviour of mineral dust. This paper is a part of research aimed at understanding how moisture interacts and alters the characteristics of coal dust. Such insight is crucial in understanding the potential toxicity of coal dust and developing mitigation technologies.

Oct 12, 2022

By R. Jacob Cefalo, Miguel Valenzuela

The modern drill and blast engineer operates in an environment often rich with data from drilling data and blast designs vs. actuals to fragmentation distributions and vibration records. Despite this abundance, much of the information generated remains underutilized, often collected as a matter of routine rather than for a means to an end. This paper explores how artificial intelligence (AI) can bridge that gap, transforming raw operational information into actionable insights that lead to more consistent and optimized blasting outcomes. Through AI-driven analysis of drilling logs, burden and spacing measurements in design vs. actual, fragmentation distributions, and vibration records, we can identify hidden patterns and correlations that traditional analytics overlook or that we may not be aware of. These insights enable engineers to proactively adjust designs and loading strategies, ultimately improving performance aspects such as improving fragmentation, minimizing ground vibration, and lowering overall operational costs. The paper examines the industry's reliance on lagging indicators, such as post-blast fragmentation surveys or actual powder factors, and suggests the need to shift toward leading indicators like real-time drill data monitoring and predictive fragmentation modeling. Utilizing AI to forecast outcomes before a blast is carried out allows engineers to take corrective actions early in the process, thereby creating a feedback loop that continuously improves performance. This integration of AI into drilling and blasting practices marks a pivotal opportunity for the explosives engineering field to evolve from reactive to predictive methodologies unlocking a new level of operational intelligence and value creation.

Jan 26, 2026

By Kazem Oraee

Implementing stable final pit walls in open pit mines during the open pit design phase and mine exploitation has become one of the most important concerns of mining engineers in recent years. Failure of mine walls can potentially cause loss of life, roads blocks, and damage to mining machinery, temporarily or permanently halt production at the face and in the worst case scenario, close the mine. Thus, the role of creating stable mine walls is crucial to safety and general operations of mines and any effort to optimize this process has great economic value for mine operators. This paper aims to illustrate the technical aspects of use of the successful presplit blasting method in metal open pit mines. It also shows that using this approach not only increases safety in mines through wall stabilization, but also will boost economic profits by savings in stripping ratio. In this regard, appropriate practical concepts for designing the drilling and blasting patterns and the role of selecting the correct drilling rigs are elaborated in detail through conducting a case study in Chador Malu iron ore mine in Iran.

Aug 1, 2013

By Rakam Lama Tamang, Michael J. Byle, Stephen Ernst

"For various reasons, dredging may become necessary in front of existing bulkhead walls, either for channel deepening or for environmental remediation of contaminated sediments. The removal of sediments at the base of bulkhead walls removes support for the toe of the wall that must be assessed. Evaluation of this impact can be problematic for aging bulkheads for which no design or construction records exist. This paper will address the steps that should be taken in investigation and analysis to assure proper assessment and means to address uncertainties and gaps in information. The steps include pre-investigation data review, field inspection, geotechnical and geophysical investigation tools, parametric analysis and design tools. Examples from several bulkhead assessment projects will be provided that include a variety of conditions and tools for application. The focus of the paper will be on the integration of technologies to assess bulkhead geometry, geotechnical properties and stability, structural safety and constructability issues with removal of support, and means of temporary and permanent stabilization for environmental applications.IntroductionBulkheads and quays have existed as long as there have been waterfront activities. Some of the earliest date back to 1200 B.C.E.(Raban, 1987), however in the United States few predate the eighteenth century. Most extant bulkhead structures, and all steel sheet pile bulkhead walls date from the early 20th century or later. These structures function to protect the shore from erosion, support landside activities, and serve as place to moor and offload vessels. Regardless of the age or usage of existing bulkheads, it is essential to assess and protect them if needed where removal of soils on the water side of the bulkheads is planned to dredging.Waterfront BulkheadsExisting bulkhead structures can be classified into two types: Cantilevered, and anchored. Cantilevered walls are completely supported by the soil on the water side, while anchored bulkheads are supported both by the soil on the water side and anchorage on the land side (Figure 1). Walls may be constructed of timber, steel, or concrete. Timber walls may be lagging with soldier piles, cribbing with soldier piles, or timber sheeted such as Wakefield walls (Figure 2). Steel bulkheads are most commonly constructed using sheet piling comprised of interlocking A or Z shapes, though some historic walls were constructed with flat sheets. Precast concrete sheet piling has also been used in construction of bulkhead walls. Anchorage may be provided by steel bars or tendons attached to deadmen, sheet piling, driven piles, or earth anchors."

Jan 1, 2017

By Edward P. Larsen

At our annual meeting in St, Louis, Mo. in February 1961, we presented a comprehensive paper (No. 61-B-22) on the subject of "Blending and Handling of Materials for Agglomeration". In that paper you will find a discussion on the difference between "blending" and "mixing". With regard to "blending" we brought out the facts of its usefulness for the preparation o materials in an agglomerated mass to attain controlled chemical and physical uniformity. "Mixing" was discredited as not being useful for the attainment of uniformity of any kind.

Jan 1, 1962

Discussions of the paper of Mr. Gayley read by title at the Lake Superior hieeting, but first presented at the New York meeting of the Iron and Steel Institute, October, 1904 (see p. 746). With the exception of Mr. Pourcel's discussion (p. 1038), these papers are here published under a mutual agreement between the Councils of the two Institutes, and will also be found, with others, in the Journal of the Iron and Steel In-slitute for the pear 1904, Mr. E. Windsor Richards, Past-President,' said that in 1799 Mr. Dawson, of Low Moor, read a paper before a scientific society in York pointing out the great diff'erence in the moisture of the air going into the blast-furnace in the hot months of the year and in the winter months. A cold blast-furnace was a very sensitive instrument, and showed this very clearly, for in June, July and August the furnace did not drive so well; it did not make the quality of iron and required more fuel; so that Mr. Gayley was on the right road to effect an enormous improvement in this direction. He considered that Mr. Gayley was on the way to great success, and hoped that the apparatus would not be a very expensive one. He supposed it mas too early for Mr. Gayley to let them know what the saviug was

Jan 1, 1905

By T. V. Ramey

Heap leaching in certain parts of the world, such as Chile's Atacama Desert, brings unique design problems in the form of possible large differential settlements of the foundation soils due to the dissolution of salts in northern Chile the soils often contain very high concentrations of soluble salts (nitrates, potassium, magnesium, and common sodium). When a leak in the liner occurs, the escaping solution dissolves these salts and triggers differential settlement. If the settlement is great enough, the geo-membrane tears, the leakage increases, triggering more differential settlement. The nitrate plants have experienced many occurrences of this phenomenon where a brine pond will undergo a sudden and complete loss of the impounded liquors. The authors present a simplified technique to quantify the differential settlement resulting from dissolution and provide a method which can be used to select a geo-membrane with suitable flexibility under axi-symmetric (multi-axial) load conditions to tolerate the predicted settlement. (This paper was previously published for Randol Gold Forum 1996 [Ref. 6]).

Jan 1, 1997

Hydrofluoric acid (HF) is traditionally used in plant operation to separate feldspars from quartz. It acts during the conditioning step as a pH regulator and an activating agent providing an excellent selectivity. However, a corrosive chemical environment and the ecological impacts from the potential fluoride ion contamination are limiting factors to use this chemical agent at an industrial scale. Investigations of the amine-feldspar interactions in the absence and presence of non-linear long-chain alcohols were carried out on two ore samples. The presence of alcohol molecules led to form a closed packed layer only on the surface of feldspars. The highest order and packing at the feldspar surface were observed with a particular alkyl chain structure as Guerbert alcohols. A new flotation process was developed and tested at both lab and pilot scales on different feldspar ores. The Guerbert alcohols allow to perform a feldspar concentrate with very low content in quartz (2.3-3.5 %) and feldspars recovery from 78 to 81 % while the aliphatic isoalcohols show a more higher recovery level (88-89 %). New HF-free process is strongly dependent on the pH range (1.7-2.5) and sulphuric acid consumption during conditioning steps. Optimal amine/alcohol weight ratio is ranged between 0.8 and 1.0. The values below 0.8 decrease strongly the flotation selectivity and the quartz recovery within the feldspar concentrates is higher than that occurs with HF.

Sep 1, 2012

By J. A. Folinsbee, Andre Robitaille, Tony Y. Chong

"Conventional crushing and grinding is followed by gravity concentration to recover free milling gold. Refractory gold, finely disseminated within the pyrite and arsenopyrite matrix, is recovered by flotation followed by pressure oxidation, cyanidation, and cementation. Non-refractory gold is recovered by cyanidation/CIP processing.A comprehensive test program aimed at improving flotation recovery was initiated in June 1995. Plant testing indicated that flotation tails value could be significantly reduced using mechanical flotation cells. Based on these test results, a flotation circuit that incorporates one of the three existing flotation columns followed by mechanical scavenging and cleaning was developed. Detailed engineering was completed in September 1996. Construction started in February 1997 and was completed in 3 months at a cost of $3.2 million. An on-stream X-ray analyzer was installed to provide real-time arsenic and iron analyses and inferred sulphur value on some of the flotation streams.The new flotation circuit proved to be an instant success. Flotation tails values were reduced by 27%. Final tails solids and solution was reduced from 0.035 to 0 023, and 0.0014 to 0.0006 oz/ton Au, respectively. Based on a mill throughput of 1,620 stpd this decrease in tails value will result in an increased gold production of 7,500 ounces per year. The payback for the project is estimated to be around one year.This paper describes the evolution of the project from bench scale testing to commissioning. Also, the operational and economic impacts on down stream processing are highlighted"

Jan 1, 1998