Search Documents

By Jeongbok Seo

This paper describes successful application of driven tapered-steel-pipe piles for two large-scale projects in the New York metropolitan area: Rego Park Mall, Rego Park, N.Y. and 164 Kent Avenue, Brooklyn, N.Y. The combination of side friction and end bearing resistance produced by tapered-steel-pipe piles has been well-recognized as greater than the side friction and end bearing resistance by pipe piles. Forty-four tapered piles were driven and tested at these two sites. Design pile load for the two sites was 260 kips for Rego Park Mall and 400 kips and 300 kips for 164 Kent Avenue. To measure the pile-drive hammer efficiency, the compressive stress in the pile, and to estimate the ultimate bearing capacity of the pile, dynamic load testing using a Pile Driving Analyzer (PDA) was conducted on index piles at the sites. Subsequent to the field testing, data analysis using the Case Pile Wave Analysis Program (CAPWAP) was conducted. Restrike PDA analysis and full-scale static load tests were performed on the selected test piles. Test piles at the project sites exhibited significant time-dependent increases in bearing capacity caused by the effects of "set-up" or "soil freeze." The dissipation of excess pore-water pressure in the soil, which had been disturbed and remolded by driven pile, was generally considered the primary cause of set-up. The increase at the subject sites ranged from 100 to 300 percent of the capacity measured at the initial driving. This paper discusses the results of various types of load testing on tapered piles and the set-up effects by comparing PDA test results acquired during and after pile driving. Finally, an empirical relationship for the New York metropolitan area has been offered for quantifying set-up.

Jan 1, 2008

By Laxman S. Sundae

Laboratory tests were conducted at the U.S. Bureau of Mines to determine the effects of roof-bolt drilling parameters on penetration rate in sandstone using tungsten carbide alloy (WC-Co) and polycrystalline diamond compact (PDC) drill bits. During the tests, water pressure of 552 kPa was found to be adequate for removing the cuttings from the tops of drill holes. Test results show that for both types of bits, penetration rate increased when thrust was raised from 227 to 1,588 kg. When water pressure rose from 554± 120 to 1,344±350 kPa, the effect on penetration rate was not significantly different. Conventional WC-Co bits became dull when one or two holes were drilled, after which the penetration rate dropped dramatically. Microscopic examination shows that the cutting edges of PDC bits also become somewhat dull, but at a much lesser rate than WC-Co tips. Microscopic examination also reveals that the wear mechanism of WC-Co and PDC bits is quite different, which may explain the longer life of the PDC bits.

Jan 1, 2010

By J Balzary, A Mohais

Dynamic market and operating conditions, coupled with an environment in which multiple objectives and trade-offs are common, pose major challenges for planners and schedulers working in any mining entity. Many mining companies recognise the need to shift from a siloed mining-focused push model to an integrated value chain, demand-driven approach, but there are still fundamental barriers in business process and the supporting technology preventing a consideration of end-to-end optimality.This paper presents some elements of experiences working with companies to adopt such advanced approaches. In addition to algorithmic elements, an approach to phased and gradual deployment of progressively more sophisticated optimisation models is described. From a practical software adoption perspective, it is believed that this last concern is also of primary importance. Next generation approaches to the optimisation of complex bulk commodity demand chains, namely iron ore and coal are presented, with case studies in the world’s largest integrated operations in Western Australia and Queensland from the raw material mined through to market. Utilising accurate simulation models supported by metaheuristic optimisation techniques, a range of ways to engineer a dynamic decision support framework that can adapt and change with the inevitable changes in commodity markets is explored. Objectives such as total revenue, margin, cost, NPV, throughput, asset utilisation, contractual penalties and bonuses, and energy consumption can be managed simultaneously across the mine, plant, logistics network, port operation, shipping and sales domains.CITATION:Balzary, J and Mohais, A, 2014. Consideration for multiobjective metaheuristic optimisation of large iron ore and coal supply chains, from resource to market, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014, pp 213–222 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

By M. R. Yenchek

The U.S. Bureau of Mines has determined a method for calculating coal mine portable power cable thermal life for a specified temperature loading. This work was the culmination of a multifaceted research project involving (1) accelerated life tests of insulation and jacket materials and (2) steady-state and cyclical loading of cables. Composite Arrhenius curves were derived for common insulation and jacket materials to identify the key cable quality that precipitates thermal failure. Plots of temperature rise versus current for popular cable sizes were then referenced to develop a correspondence between cable life, based upon thermal degradation and current loading. Predictions of cable thermal life were made through integration over variable load cycles and, consequently variable operating temperatures. This procedure may have utility for both the U.S. Mine Safety and Health Administration and mining machine designers in determining the appropriate cable size for new equipment.

Jan 1, 1991

By Yang Ge, Yuzhu Pan, Mansheng Chu, Jue Tang, Cong Feng, Lihua Gao, Zhenggen Liu

The low-grade nickel laterite ore used in this study was successfully upgraded through selective reduction by industrialized rotary kilns followed by magnetic separation. The results indicated that both iron metallization extent and nickel metallization extent showed obvious linear correlation. In addition, rational roasting temperature and prolonged grinding time could enhance the overall fineness level of reduced laterite nickel ore. The moderate roasting temperature at a range of 1100–1150 °C should be suitable enough to a conversion of total nickel to metallic nickel and partly inhibited the conversion of total iron. Ultimately, the obtained ferronickel alloy with a nickel content of 7.32% and an iron content of 84.15% was prepared successfully from the lowgrade nickel laterite ore containing a nickel content of 1.92%. Nickel and iron recoveries were 96.72 and 89.08% respectively, which achieved the highly efficient recovery and utilization of iron and nickel from low-grade laterite nickel ore

By M. P. Davies

"Risk, the product of probability and consequence, is an integral part of mining. Whether evaluating exploration priorities, determining property acquisition potential, reviewing the components of an operating mine or assessing environmental/closure issues, the concept of minimizing risk is central to economic and technically appropriate decision making.Until recently, risk evaluations have tended toward a strongly mathematical basis. With this previous trend, it was essential to establish precise probability density functions to all assessed components or issues where often little information was available. The combined effect of the seemingly complex analyses with corresponding insufficient data often resulted in either a poorly executed risk evaluation or no evaluation whatsoever; either result not acceptable for optimal decision making. This paper presents a simple and practical procedure to carry out risk assessments for the mining industry. Although simplistic in nature, the power and usefulness of the technique is immense. The basis for the procedure involves combining deterministic assessments (often “gut feel”) with appropriate probabilistic descriptors. The resulting procedure, termed Potential Problem Analyses, or PPA, can be used anywhere an evaluation of risk will assist in optimizing technical and/or economic decisions. As will be shown, a key element of the PPA procedure is the multi-disciplinary input the framework allows which makes the method ideal for a teamwork approach to decision making."

Jan 1, 1997

The principal activities of the Bureau of Mines Explosives Research Center from July 1, 1963 to June 30, 1964 are described briefly in part 1. Part 2 gives short abstracts of publications that appeared during fiscal year 1964; in general; the research reported in these publications antedates the report period. Part 3 describes a short-term investigation into safety problems associated with shipping of molten sulfur; this investigation is not at present destined for publication elsewhere.

Jan 1, 1965

By S. Banisi, A. Haji-Zadeh, A. R. Hasankhoei, M. Maleki-Moghaddam

At the concentration plant of the Gol-E-Gohar Iron Ore Company (Iran) three 9m × 2.05m AG (Autogenous) mills (fixed speed) are used in parallel in a dry operation. The test works conducted in a scale down mill with a diameter of 1m indicated that conventionally used "deflector" type liners did not provide efficient environment for grinding. In this research, to improve the grinding efficiency, a new design using low profile end liners incorporating radial ribs of proper height was investigated. In order to determine an appropriate liner design at different operating conditions, a 100cm×10.8cm model mill was used for experimentation. The special design of model mill made it possible to increase the radial ribs height in steps of 6mm up to 18.5mm. The transparent end of the mill enabled accurate trajectory determination by image analysis. The results indicated that the new lower height profile deflectors and 15.5mm-height (14.5cm in industrial scale) radial ribs improved the mill performance while avoiding excessive pressure drop across the mill and wear on the liner. The image analysis showed that the use of new liners increased the distribution of coarse particles across the mill cross section from 28% to 35%. A new liner design was proposed by decreasing the number of liners in each slice from 5 to 4 pieces. The thickness of the inner head liners reduced from 45cm to 30cm and the outer deflector liners replaced by radial ribs. The distance between the feed and discharge inner head liners increased from the original 115cm to 145cm which increased the effective length of the mill by 26%. The new design reduced the weight and volume of end liners by 9% and 23%, respectively. It was predicted that the new liners design increases the mill throughput by 10% and reduces the metal consumption by 20%.

Jan 1, 2016

By A. Aubin, H. Yang, G. Zaluski

The Athabasca Basin of northern Saskatchewan and Alberta is an exceptionally rich metallogenic region, hosting more than 2.8 B lb U3O8, of which over 927 M lb U3O8 have been mined out since extraction first started in the late 1970’s. A detailed compilation of several empirical features of 85 deposits located within the basin was conducted in order to understand the distribution and variability of the geological characteristics of the mineralization and its associated alteration. A new empirical classification was devised based on four parameters: 1) geometry of the mineralization (dimensions and relation to the unconformity surface), 2) size, grade and metallurgical complexity of the mineralization, 3) lithostructural setting, and 4) extent and nature of associated alteration haloes. This compilation defines the footprint characteristics of the Athabasca Basin deposits, which guides decision-making processes from early exploration and discovery to resource expansion and extraction.

Jan 1, 2020

By J. W. Thompson

OIL AND GAS AS MINERALS. Oil and gas within the ground are minerals and the fact that they have attributes not common to other minerals because of their fugitive nature or vagrant habit, and the disposition to percolate, and the possibility of their escape from beneath one part of the surface to another, does not remove them from the class of minerals. Texas Co. v. Daugherty (Texas), 176 Southwestern, 717, p. 719, May, 1915. OWNERSHIP OF TAILINGS-ABANDONMENT. A corporation engaged in milling- and the reduction of ores deposited the tailings therefrom upon a portion of its own land lying in a gulch through which water flows at times in great volumes and with great force' and notwithstanding all reasonable efforts by dams and otherwise to retain its tailings, the tailings eventually were forced upon the lands of an adjoining owner; these tailings were valuable and their retreatment, intended by the mill owner, profitable; and the fact that the tailings were so washed down upon the lands of the adjoining owner and permitted to accumulate and remain for some considerable time is not sufficient to show an abandonment on the part of the owner of the tailings, where it is clear that the owner had no intention of so doing, but on the contrary, always intended to conserve and retreat the tailings.

Jan 1, 1916

By Scott Turner

We are here today to witness the graduation of 63 young men as Engineers in the mineral industries . It is an important occasion and one in which the public takes a keen interest , since this school has long been famous for the educational facilities it affords young men, and for the high professional standing of its graduates . : : : It is fitting that once each year we should pause to review the path the student has traveled , and to reflect upon the perspective opening before him as an engineer . I was invited to come from Washington to take part in this ceremony and to say something to these young graduates . In searching for a theme ," it occurred to me. that perhaps my best contribution would be to duscuss certain beliefs as to college training , deal with the situation in which the young engineer finds himself on graduation , touch on the new ideas of the social and political responsibilities of the engineer , and point out what he may expect to find in practice , and , above all , what he must do to orient himself properly in the mining profession and maintain the best traditions of our brotherhood . Let us first review your college days and see what they have done for you . I am told there are still many temptations in college . I know there used to be . Rest assured the same holds true in the professional life ahead of you. The main difference is , perhaps , that your greatest temptations in college were those offered by your teachers , who tried to entice you into realms of harder work, closer application , increased concentration , clearer thinking and better understanding , by animating your curiosity and increasing your powers of reasoning and of observation . In other words , here you have carefully and systematically been decoyed toward finer and loftier things . Do not expect that similar helpful influences will greet you on every side in your professional life . Often quite the contrary is the case .

Oct 1, 1930

By Bern Klein, Tichang Sun, Daozhen Gong, University of Science and Technology Beijing, Chunbao Sun, Stefan Nadolski

"This paper is focused on the effect of modifying the SAG mill/ball mill transfer size on the energy efficiency of SABC circuits. The transfer size is considered to be a parameter which provides operators with the opportunity to improve comminution circuit performance. In this study, the Moly-Cop tools package was employed to predict the energy consumption of SAG mill and ball mill circuits under different operating conditions. An Energy Benchmarking model was adopted to calculate grinding energy efficiency. The SABC circuit at the Huckleberry mine was selected for this case study. It was observed that after increasing circuit transfer size (T80) from the existing 3.3 mm to 4.8 mm, the Benchmark Energy Factor (BEF) of the SABC circuit decreased from 4.30 to 4.05. In terms of energy consumption of the SABC circuit, 1.17 kWh/t of specific energy saving was achieved through the transfer size optimization.It was also observed that when a transfer size was selected such that both SAG mill and ball mill circuits operated at their highest energy efficient states, the entire SABC circuit was the most energy efficient. The maximum energy efficiencies of these three circuits were all approximately 25% when compared to the minimum practical energy required to carry out an equivalent comminution duty. Single-particle compression breakage testing was used to determine the minimum practical energy associated with the Huckleberry mill feed. In combination with geo-metallurgical data, this study also provides an opportunity to perform dynamic optimization of SABC circuits."

Jan 1, 2016

The United States is being invaded... by foreign capital: marks, francs, pounds, yen, lire, riyals, you name it: On almost any given day the Wall Street Journal will contain a new report on a department store, newspaper, bank, hotel, agricultural land, supermarket chain, et a1 being bought into by overseas investment. Xenophobic reaction to this revised national condition has begun to set in. Several farming states have and are introducing legislation to monitor foreign land buying. In Congress a mandatory reporting requirement for foreign purchasing is currently under study. In a relatively short period the country has reverted from world leader- ship in overseas acquisition and involvement to become itself one of the prime investment opportunities in existence. Interestingly enough, one of the industries where this changed status has become most apparent and pronounced is within that small/regional/segmented/low value-to-weight bulk commodity enterprise ranked as the backbone of the nation's construction activity. U.S. cement making is not only undergoing internationalization in its ownership, but also in its product, equipment, and engineering expertise.

Jan 1, 1979

By John W. Motter

The Green Mountain Copper Prospect is an unusual stratiform base metal occurrence located in the California Foothills Copper-Zinc Belt. Mined for rich secondary oxide-carbonate ores since 1863, the first serious exploration of the primary ores was in the 1970's. Unlike typical volcanogenic deposits of the district, stratigraphy consists of greywackes overlain (?) or intruded by an intermediate to felsic volcanic unit. Shales and siltstones overlie the volcanic unit. Massive pyrrhotite, chalcopyrite and sphalerite occur at the top of the volcanic unit. Later intrusion and deformation metamorphosed the sequence and created a SW plunging anticline. Characteristic magnetic and electrical geophysical signatures are present and reviewed.

Jan 1, 1978

By P. M. Daling, C. A. Geffen

The objectives of this study were to examine a representative cross section of formal safety analysis techniques developed for the nuclear and aerospace industries, to recommend those methods that would be suitable for application to the mining industry, and to include those methods in a user's manual. Volume XI of this report, the user's manual, describes several methods that were determined to be immediately transferrable to the mining industry. The handbook gives detailed instructions on appropriate application and utilization of the methods. Other techniques will require further development before they can be effectively transferred to the mining industry.

Jan 1, 1983

By J. D. McAteer

It is widely agreed throughout the mining community that federal mine safety and health legislation administered by the Mine Safety and Health Administration (MSHA) deserves significant credit for the past quarter-century's remarkable improvements in miner safety and health. Recently, however, it has been suggested that the mining industry in the United States has now evolved to a point that current mine safety and health law may be obsolete. This proposition deserves attention. Today, I propose to give it the close logical scrutiny that is its due. I conclude that the obsolescence of current mine safety and health law is not supported by the evidence. The existing mine safety and health law continues to serve as a critically important supplement to mine operators' safety programs at a modest cost to the taxpayer. At the same time, trends in a changing industry do call for responsive adaptations in the Federal mine safety and health program. I will argue that timely and appropriate responses to changing needs can be accomplished within the framework of existing legislation, provided federal officials avail themselves of the flexibility provided by existing law.

Jan 1, 1996

By L. M. Pidgeon

MAGNESIUM metal, with a specific gravity of 1.73, is two-thirds the weight of aluminium and one-quarter that of steel. It is the lightest metal which is stable in the atmosphere. Before the war it had begun, though somewhat slowly, to take a place among the established metals. In 1939, magnesium production on this continent amounted to some 3,000 tons per annum and was confined to one company. At that time, Germany produced perhaps 20,000 tons. The advent of war, however, increased the demand to fantastic heights and introduced production problems of unprecedented magnitude. By the end of 1943, North American production is expected to reach 300,000 tons per annum (1), an increase of one hundredfold. Such a rate of expansion has not been witnessed previously in the history of metallurgy. It has given the metallurgist an opportunity to try new production methods and to learn in a short time what might otherwise have taken many years. The metallurgy of magnesium is still in its formative years and at this time widely different production methods are in operation side by side. This paper will discuss these methods in so far as information is available for publication at this time. A general description of the new Canadian industry will be included.

Jan 1, 1944

By G. R. Palmer

Using a fluidized, countercurrent multiple-compartment ion-exchange (MCIX) column previously developed by the Bureau of Mines, Bureau researchers have successfully extracted uranium from a simulated acidic in situ leach liquor that contained 150 ppm U30s? This successful demonstration of the MCIX system is reported, and the effects of varying the operating conditions on the performance of the system are also examined. Operating the MCIX system with a flow rate of 15 gpm/ft2 and an aqueous-to-resin flow ratio of 200:1, more than 90 percent of the uranium Has extracted, and a resin containing approximately 28 grams U308 per liter was produced. The absorption column used to investigate the operating variables was approximately 18 feet long with a 2-inch ID and was divided into compartments that were 1 foot long.

Jan 1, 1980

Exploration for SX-EW copper deposits and plant operation depend largely on the copper and gangue mineralogy inasmuch as? they govern the feasibility of leaching. Mineralogical parameters are pivotal in identifying if an ore is suitable to dump, heap, thin layer, vat or agitated leaching and/or if the ore requires curing, bioleaching or alternate lixiviants. Problems in metallurgical testing, production leaching and recovery forecasting are very often related to lack of mineralogical data. This presentation will illustrate the use of quantitative mineralogical analysis for exploration, acquisition assessment and optimization of copper leach operations.

Jan 1, 1996

By D. Williamson

In the post war years metals analysts and statisticians have generally tracked the demand for metals in line with changes in OECD industrial production (IP) growth rates because, undoubtedly, the correlation between IP growth and metal demand was reasonable. However the correlation was exaggerated. During times of expanding IP growth metal demand increased at a faster proportional rate than IP growth. This was probably due to industry restocking in anticipation of growing demand at the start of each economic cycle. Conversely, metal demand would slacken at a greater rate than would be suggested by negative IP growth as industry destocked in order to reduce costs. Nonetheless, overall, a reasonable correlation between IP growth, over the longer term, and metal demand could be painted. Yet, although this correlation has stood well since the last world war it has been based on the fact that the bulk of the world's IP growth stemmed from the industrialized countries of the western world, latterly including Japan. The so called "developing world" was of little consequence, whilst countries of the Soviet Union and Communist Bloc were deemed to be closed, self-contained entities which, for each metal, would either be net exporters or importers. These quantities would be used by analysts to calculate the overall supply/demand equation for the western world only and to deduce whether a commodity was in shortage or surplus. It is now believed that this method of projecting total world supply and demand for raw materials is outdated and takes little account of the worldwide political changes which have occurred since the collapse of communism and the revitalization of China, albeit under a notional communist government. It is no longer appropriate to assess global balances for raw materials on the basis of three economic blocs namely, western world, developing world and communist bloc. Rather, global balances need to be projected on a global basis. In this regard, since the collapse of communism and the removal of many other totalitarian regimes, capitalist forces are at work and are attempting to satisfy, with some considerable success, the expectations of the great mass of the world's poorer people. Such people, usually located in Asia, Africa and Latin America have aspired to the same standard of living as people living in western Europe, North America and Japan. Now, with free market forces at work their aspirations will start to be met. Consequently, the demand for metals and other raw materials will now rise at a much faster rate than at any other time in the world's history. Not only will the production of raw materials have to keep pace with rising IP in the developed world but will also have to keep pace with the demands associated with the rising expectations of rapidly increasing populations in the developing world, as well as from within the old communist bloc countries. This paper sets out to argue the case that metal demand could well increase at a rate faster than the world's mining companies, governments and financiers can deliver.

Jan 1, 1997