Search Documents

Laboratory tests were conducted by the U.S. Bureau of Mines to determine respirable dust reduction effectiveness of and interaction between face airflow and water sprays for a continuous miner. Increases in exhausting face ventilation from 3,000 to 9,000 cfm, in waterflow from 15 to 35 gpm, and in water nozzle operating pressure from 80 to 200 psi were evaluated. Results indicated that airflow had the greatest individual impact on reducing dust levels, with concentrations at return and operator sampling locations reduced by as much as 57% and 99%, respectively. Regression modeling was utilized to predict dust concentrations over the range of values tested for the control parameters. Interactions between the control parameters were significant and often defined an optimum level where further increases in that parameter failed to produce additional dust reductions. Increasing airflow to 8,400 cfm, waterflow to 25 gpm, and water pressure to 140 psi typically reduced dust concentrations at operator and return locations. Application of a control parameter above these levels can provide additional dust reductions if used in conjunction with appropriate levels of the other two control parameters. Otherwise, higher operator dust levels may result and can be attributed to increased rollback and/or airflow turbulence.

Jan 1, 2010

By J. Kretschmann

"By the end of the 1950s, the German hard coal mining industry produced 150 million tons of hard coal per year in 170 collieries with 600,000 employees. At that time, 70% of the primary energy demand of the Federal Republic of Germany was covered by domestic coal. However, due to coal mining becoming an increasingly globalized business and the oil and gas industry producing with lower costs, the German domestic hard coal industry stood constantly under restructur-ing pressure. The industry declined until the end of its life cycle. In 2007, a political understanding was arranged to phase out German hard coal mining in a socially acceptable manner by the end of 2018. This decision required a new strategy for the coal mining industry. Being strictly finalized, the German hard coal mining industry has to be prepared for the post-mining era. To create a sustainable development strategy, the long-term impacts of coal mining activities in Germany concerning the environmental, economic and social dimensions will be analyzed systematically and forward-looking. The regional and social responsibility during the closing process and for the post-mining era will be emphasized. High technical standards in environmental protec-tion and post-mining technologies, as well as long term experiences in the development of former mine sites to create new jobs are significant from an international point of view. The traditionally constructive social partnership between employers, union, and employees has enabled long-term stable adaption processes and avoided social friction. The sustainability strategy of the German hard coal mining industry can be regarded as a role model for other mining countries and regions facing similar transition challenges. INTRODUCTION Principally, mining is a finite business that reaches its end if the deposits are depleted or the raw materials can no longer be mined in an economically profitable way. However, the impact of mining is po-tentially an infinite one – at least if you measure it at a human time scale. Mining always means interfering with geological and ecological structures that cannot be reversed to their original condition. In general, the mining cycle (Figure 1) can be divided into three phases: 1. The exploration phase, in which the deposit is investigated to determine its technical and economic profitability. The period of these undertakings is relatively short and can lead to the launch of mining operations. 2. What follows is the actual mining phase which usually lasts for a long time and ends latest when all deposits are fully depleted. This lifespan may be shortened if the economic conditions (production cost or market price) deteriorate. Nevertheless, mining may be resumed if those conditions become favorable once more (examples are silver mining in Germany or rare earths mining in the USA). 3. The longest phase, however, is the post-mining phase as the human interference into geology and nature is usually inten-sive and irreversible. Mining can lead to consequences which have a permanently adverse impact on people and the environment; therefore, they have to be managed as best we can (1)."

Jan 1, 2017

By Vanessa M. Torres

Cia. Vale do Rio Doce is currently developing Niquel do Vermelho Project. The laterite deposit is located at Carajas Mineral Province at less than 15 km from Sossego Copper Project, scheduled for start-up in 2004. The available infrastructure, includes paved roads, large capacity railroad and port complex owned by CVRD, power supply and good quality water. The project was evaluated in the past for ferronickel production. In the late 1990s, CVRD switched its attention to investigating the usage of pressure acid leaching. The combination of good metallurgical behaviour for pressure acid leach (PAL) process route with reasonable mineable grades, and existing infrastructure justified the start of engineering studies in 2002. The project approach at the engineering phase is based on the dual objective of minimizing risks while maximizing project profitability and value. CVRD is currently completing the Niquel do Vermelho prefeasibility study. This paper outlines the main outcomes of the study and future perspectives for the project.

Jan 1, 2004

By R. W. Pauls

"Many tens of thousands of hectares of forested land will be disturbed and reclaimed in the surface mineable Athabasca oil sands area during the next few decades. The surface area disturbed by Syncrude’s Mildred Lake development alone exceeds 10 000 ha to date. It is not clear that reforestation of disturbed areas will best accommodate the aspirations of all stakeholders, particularly traditional users of the land. A five-year research program by Syncrude Canada Limited and the Fort McKay First Nations has examined the feasibility of raising bison on land reclaimed after disturbance by oil sands development. Forage productivity and carrying capacity for bison was comparable to that of grasslands elsewhere in Alberta. Concerns regarding compaction of newly rebuilt soil by bison traffic proved unfounded. Bison demonstrated weight gains typical for ranched bison and calving rates averaged 90%, a value typical for ranched bison. The animal husbandry problems encountered were typical of those occurring on bison ranches elsewhere in Alberta. An economic analysis indicates that a 1000 ha bison ranch on reclaimed land has a net present value that compares very favourably with a similar area supporting commercial forest. Subject to approval by Alberta Environmental Protection, the current research project will be expanded as a pilot commercial ranching venture in order to explore its commercial viability as a business venture by the Fort McKay First Nations. At the same time, measures will be implemented to resolve various regulatory issues associated with commercial bison production in the oil sands area.BackgroundSyncrude Canada Ltd. (Syncrude) is proposing, in its land reclamation strategy, a feature that is, depending on one’s background and perspective, regarded as an innovative approach to land reclamation, a threat to the regional forest industry, a creative response to aboriginal stakeholder concerns, a reneging on reclamation commitments, an opportunity to provide an ongoing economic base for postoil sands regional economy, or an environmentally unsound use of the land. These diverse and sometimes strong reactions have been generated by the proposal to introduce bison, either free-ranging or commercial ranched, to the reclaimed landscape."

Jan 1, 1999

By Roger L. Hulette

Mt. Newman Mining Co. is now completing an expansion program, begun even before initial construction was complete, which will result in facilities with the ability to ship over 30 million tons of iron ore per year by early 1973. Confidence in such rapid future growth was evidenced by careful planning for the future expansion of those facilities provided for initial operation of the project which first shipped ore on 1 April 1969. Ore sales contracts totaling more than 300 million tons have been negotiated, thus justifying the optimism which led the joint venturers to provide over $200 million in initial investment and a like amount in capital required to finance the continuing expansion program. Members of the Mt. Newman Joint Venture are: Amax Iron Ore Corporation - 25% (a subsidiary of American Metals Climax) Pilbara Iron Ltd. - 30% (a subsidiary of Colonial Sugar Refining) Dampier Mining Ltd. - 30% (a subsidiary of Broken Hill Proprietary) Seltrust Iron Ore Ltd. - 5% (a subsidiary of Selection Trust Ltd. of London) ? Mitsui C. Itoh Iron Ore Pty. Ltd. - 10% Mt. Newman Mining Co. Pty. Ltd. manages the project on behalf of the five companies which make up the joint venture.

Jan 1, 1972

By Robert J. Gorney

This paper deals with the actual application of a direct digital control to simple as well as complex industrial process control loops, Fundamental descriptions of preliminary research and design are described briefly, as is the development of the present day controller and control computer. The results and effects of direct digital control in various types of single and cascaded loops as opposed to the use of conventional controls are discussed. Computer supervision of a process and control override are taken into account, in addition to methods of short and long term plant economic optimization.

Jan 1, 1965

By P Vass, C Butler, J Condon, B Hooper

DeGrussa Copper Mine, resource status 10.2 Mt at 5.7 per cent Cu, 2.1 g/t Au (Sandfire Resources, 2013), commenced concentrate production through its 1.5 Mt/a conventional copper flotation processing plant in September 2012. Geometallurgical assessment during the feasibility study identified potential process-critical ore factors that required further investigation to determine potential impact on processing. Ore characterisation and metallurgical processing performance test work of ore types ensued and subsequently, the first quantitative DeGrussa geometallurgy model was born. Now one year into steady state production, the geometallurgical program has evolved significantly from its infancy and provides valuable insight into ore characterisation and behaviour in the processing plant. This paper details geometallurgical investigations undertaken at DeGrussa to date; from feasibility metallurgical test work through to geometallurgical modelling and management practices, as well as reconciliation between observations at feasibility study level and subsequent observations in production.CITATION:Condon, J, Butler, C, Hooper, B and Vass, P, 2013. DeGrussa Copper Mine, Western Australia - feasibility to first production: a case study in developing a working geometallurgy model from first principles, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 59-66 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

By S. Banisi, A. Ghasemi, S. Zare, F. Ghorbani, E. Nematollahi

"Comminution is the most energy intensive operation which constitutes the major portion of operating and capital costs of the mineral processing plants. Working at the maximum operating capacity of comminution equipment plays a significant role in the efficiency of the circuit. Appropriate design of cone crusher feed box could result in the choked crushing which is known as a vital factor in achieving target performance. In this research, the non-uniform cone crusher feeding at the Sarcheshmeh copper complex was studied and appropriate measures were taken to solve the problem. The problem resulted in non-uniform and high wear rate of crusher liners and high fluctuations of power draw. In recent decades, the discrete element method (DEM) has been applied successfully to study the effect of different factors on the behavior of particles flow. In this work, various designs for feed box were tested using an in-house developed DEM software called KMPCDEM©. The best feed box design obtained from the simulations was selected, constructed and installed in of the cone crushers. The new feed box design resulted in more uniform feed distribution on the distributor plate of crusher indicated by a reduction of the standard deviation of power draw measurements from 13 to 3 kWh. The better control of the crusher, 49% increase in the crusher throughput and finer and narrower product size distribution were the main outcomes of the installation of the new feed box. Furthermore, the wear rate on mantle and liners of crusher not only decreased but it also became uniform.INTRODUCTION Comminution is the most energy intensive operation which constitutes the major portion of operating and capital costs of the mineral processing plants. Reaching the maximum operating capacity in comminution equipment is a key sign of approaching the nominal productivity of the process. Due to the effect of crusher efficiency on the downstream circuit performance, optimization of the crushing circuits has received considerable attention (Herbst, & Potapov, 2004; Quist, & Evertsson, 2010; Li, Huiqi, McDowell, Glenn R, Lowndes and Ian, 2014; Cleary, Sinnott, Morrison, Cummins, & Delaney, 2017). Improving the performance of crushing circuits not only decreases the capital and operating costs but also increases the efficiency of downstream grinding circuits (Jacobson, Janssen, & Urbinatti, 2010). In cone crushers particles can be subjected to two different modes of compressive breakage; single particle breakage (free feeding) and inter-particle breakage (choked feeding). The maximum efficiency of the cone crusher directly depends on the type of feeding arrangement (Operation Manual, 1977). An appropriate feeding must lead to choked feeding the cone crusher. If the rate and method of feeding the crushers are correctly be executed, the maximum efficiency of the crushers could be available (Jacobson et al., 2010)."

Jan 1, 2018

By L. V. Bell

THE object in prospecting is to find ore. With the exception of certain discoveries of more or less accidental nature, intelligent prospecting as conducted today is, whether consciously or not, based upon a process of elimination. In the following discuss on it is proposed to evaluate those factors that enter into the eliminating of certain tracts of ground and, conyersely, the concentrating of attention upon others. The danger of generalizations as to the barrenness of cer.ain areas, without having due regard for all such factors, is emphasized. The fact that our conception as to what areas or rock formations are to be regarded as favourable or unfavourable is, in some measure at least, changing with new discoveries under diverse and unexpected circumstances, adds more point to the discussion. The criticism might be raised that the subject is treated largely from the standpoint of geology, but that may be met by stating that it is, and must continue to remain, precisely from this standpoint that the prospecror directs his activities. Briefly, the geologist may render the greatest service to the prospector in the early steps of selecting (a) the general territory in which to prospect; (b) the area to be intensively prospected; and, finally, (c) those parts of the claim or claims to be prospected in detail. Although certain phases of the discussion will be, in some measure, of general application, we shall here concern ourselves essentially with prospecting in the pre-Cambrian shield. Furthermore, the subject is so large that it has been decided to limit it to a consideration of that portion of the pre-Cambrian rocks in which is situated the mining district of western Quebec, of which the writer can speak with more personal knowledge. This limitation need not, however, seriously detract from whatever merit the discussion may possess, since the deposits concerned cover a fairly wide range of metallic ores, including gold, copper with associated zinc, and, lastly, molybdenum.

Jan 1, 1936

By Paul M. Tyler

In 1939, American industry got, off to a poor start, slowed down further during the first quarter, quickened after May, speeded up still more when war broke out again in Europe, and ended the year at a pace close to an all-time record. The average index of general business activity for the entire year (105) was well ahead of that for 1938 (86), failed to equal that of 1937 (110), and fell behind the average for 1929 (119) by a wide margin. (Federal Reserve Bank yearly indexes in parentheses).

Jan 1, 1940

By Mike Fontaine

The success of a project is defined by meeting the financial performance objectives of the business case within a stipulated timeframe. Early in design, little information is normally available; the uncertainty introduces risk to the project outcome. Using a range of risk management tools and techniques, a project can be developed from front end loading phases 1 through 3 (FEL1–FEL3), and project implementation (FEL4) and then into operations with an optimized probability of success. For every project element, the risk management framework embodies: establishing a context; assessing risk (identify, analyze, and evaluate); and treating risk. Embedded within design activities, this process mitigates or eliminates risks. Monitoring and control, as well as extensive communication and consultation with stakeholders, is integral to the risk management process.

Jan 1, 2015

By C. W. Drake, J. H. Walsh

"The Canadian Carbonization Re-search Association was formed during 1965, with seven founding members representing four integrated steel companies, two coal companies and one high-temperature tar processing company. The purpose of this paper is to review the circumstances which led to the formation of this new research association and to discuss its general objectives. Also discussed will be the organization of the Association, the nature of its relationship with the Department of Energy, Mines and Resources in the early stages, and some of the technical programs which have now been initiated."

Jan 1, 1967

P. H. Dudley, Yew York, N. Y. (communication to the Secretary*) :—The characteristics of Professor Home's metallurgical papers are, that he is able, from the mass of confusing evidence on the subject, to make an analysis and present hypothetical and essential principles in concrete form for consideration and discussion. I can appreciate, from the practical side of the subject, the labor of collecting and investigating the data which was essential to prepare the paper. Much of it necessarily came from material of preceding years of manufacture in which time was allowed for chemical reactions of the re-carburizer, and for the elimination of the oxidation-products before teeming the ingots. This practice gave a favorable time-element to free the metal from slag and other impurities— a requisite condition for the production of sound steel in the ingots. But, in allowing them to become cold before they were charged into the furnace, a subsequent time-element entered as a detrimental factor in the development of the pipe or shrinkage-cavities, which gave an ingot-structure deficient in soundness, at least in the upper portion. (The term slag is used in a general rather than in a strictly technical sense.) Traces of manganese sulphide are often associated with manganese silicates in the same thread or seam, and at other places they are separate and distinct. Interpretations from material thus manufactured must be made with due allowances for the methods of fabrication and the requirements of service. The only way we now have to estimate what the degree of soundness of the ingot-structure was, in the early foreign and American manufacture of steel rails, is by examination of the worn and failed material after years of service. We must remember also that the poorest material was long since consigned to the scrap-heap without any full record of its history. The rails from a given ingot cannot now be identified ; and in many

Jan 1, 1909

By Heinrich Ries

I. INTRODUCTION. THE facts is presented in this paper, based chiefly on recon¬naissance made, during the summer of 1903, by myself and my assistant, Mr. R.. C. Brooks, cover practically all that portion of Texas lying east of the 99th meridian. The work was undertaken for the University of Texas Mineral Survey, and was to have been extended over the entire State, but the sudden termination of the survey prevented even the official publication of the results already obtained. Most of the mineral resources of Texas were fully treated by the First Geological Survey, but the clay-industry was tit that time little developed, so that only a few scattered notes concerning it are to be found in the Survey reports. The extensive exploitation of the clay-deposits, however, has emphasized their commercial importance, and has also made accessible many facts of exceptional interest concerning their geologic conditions. The erection of new plants for the utilization of clay-products is usually preceded by more or less prospecting, which, by reason of the scarcity of outcrops, and the geologic and topographic conditions of eastern and southeastern Texas, is often slow and difficult work. This is especially true in the Tertiary and Pleistocene areas, where the structural conditions much resemble those of the Atlantic coastal plain, the deposits being mostly lenticular in form, and surrounded by beds of sand. II. GENERAL GEOLOGY OF THE CLAY-DEPOSITS. The accompanying sketch-map, Fig. 1, shows the location of nearly all the deposits examined, their relation to the geology of the State, and the type of clay found in each. The geology is based on the published work of Hill, Cummins, Tail, Adams, Hayes and Kennedy, but the boundaries have unfortunately not been determined over the entire region covered by the map, and, in many areas, are only approximate. It will be seen that the clay-deposits range from Carboniferous to Pleistocene in age, the older deposits being found in the northwestern part of the area, while those of Cretaceous and Tertiary age lie to the east, southeast and south. The Pleistocene clays are found in part in a belt along the coast, and in part along many of the larger rivers, where they often underlie extensive terraces.

Sep 1, 1906

By Tadeu Messias Donizete Borba

A soldagem com elevado aporte térmico é uma das alternativas adotadas pelos estaleiros para aumento da produtividade nas operações de união de materiais. No entanto, os ciclos térmicos gerados durante a soldagem podem provocar transformações microestruturais prejudiciais à tenacidade na zona afetada pelo calor (ZAC). Este estudo teve como principal propósito realizar a caracterização microestrutural e avaliar as propriedades mecânicas da ZAC do aço naval Sincron EH36 produzido na Usiminas por laminação controlada seguida de resfriamento acelerado em comparação com um aço de mesma classe de limite de escoamento produzido convencionalmente, ambos soldados pelo processo ao arco submerso em dois níveis de aporte térmico: 76 e 130 kJ/cm. Foi observado que a presença de uma microestrutura mais refinada nas diferentes regiões da ZAC, associadas ao menor tamanho de grão do metal base e ao menor carbono equivalente, foram os principais fatores que contribuíram para a excelente tenacidade da ZAC do aço Sincron em comparação ao aço convencional. Os resultados obtidos mostraram que é possível obter juntas soldadas com excelentes propriedades mecânicas ao se empregar aço Sincron para a soldagem com altos aportes de calor, e sua utilização pode ser uma estratégia para otimização dos tempos e custos de fabricação na indústria naval.

Aug 8, 2018

By Jian-hua Ren, Guang-liang Wu

A lot of dust is produced in iron and steel enterprises, giving rise to serious environment pollution, with which all countries are trying to find methods to deal. The influence of relevant technological factors on dephosphorization was investigated in laboratory, and the effect laws of that were analyzed. The results demonstrate that, in the given conditions of the best slag-metal proportion for hot metal dephosphorization is 1:10, and the optimum temperature is 1350 , The phosphorus distribution ratio of dephosphorization agent containing converter dust of 30% has the maximal value, with dephosphorization rate reaching 85%. Under the optimal conditions, premelting dephosphorization agent can significantly improve the ability of dephosphorization, dephosphorization efficiency increasing to 92%. Therefore, the dust can substitute the oxidant and fixative of dephosphorization agent, be used in hot metal dephosphorization, to enhance the efficiency of utilization.

Jan 1, 2016

By Gust Van Lysebetten, Monika de Vos

The objectives of monitoring geotechnical structures can be very diverse, including optimisation of the design, quality control, long term performance assessment, and approval of innovative execution techniques. In this context, new measurement techniques, based on optical fibres, offer the possibility of accurate strain and temperature monitoring with very small sensors and limited numbers of cables. This paper briefly presents optical fibre sensing techniques and illustrates their application to geotechnical structures by means of some projects, carried out by the Belgian Building Research Institute (BBRI).

May 1, 2022

By Mustafa Kumral

Monte ? Carlo simulation is often used to assess the risks associated with uncertain variables in mining operations. The success of Monte-Carlo simulations depends upon reproducing the dependencies among variables to some extent. However, some variables may exhibit different dependency patterns. In these cases, classical techniques for dependency quantification cannot capture dependencies. As an alternative, the copulas allow modeling nonlinear dependencies. Furthermore, any choice of marginal distributions can be used. Especially, for the data, which is sensitive to extreme case such as financial crisis, the copulas arise as a means to reproduce the correlations among variables. In this paper, the copulas are introduced to mining practitioners using Monte-Carlo simulations for risk assessment. Then, a case study is given to show the superiority of the copulas over classical techniques using ModelRisk Software. In conclusion, it was observed that the copulas enhance the quality of Monte-Carlo simulations by capturing variable dependencies.

Aug 1, 2013

By Ashish Ranjan Kumar, Steven Schafrik, Oscar Velasquez

Flooded-bed dust scrubbers installed on continuous miners use fibrous type multi-layered filters to capture dust from the airstream. Prolonged operations of the scrubber could lead to filter clogging due to dust accumulation. This results in reduced flow through the scrubber and elevated dust levels in the mine environment. This paper compares the performance of a conventional fibrous screen filter and a novel impingement type dust filter. The impingement filter is a self-cleaning system and was designed to have a resistance similar to the fibrous filter. The cleaning efficiencies for these filters were computed using iso-kinetic sampling and optical counting of coal dust particles in a clean unclogged state. The cleaning efficiency of the impingement filter also increased with an increase in particle size and was comparable with the conventional fibrous filter. The cleaning efficiency of the fibrous filter improved significantly with an increase in water flow. The non-clogging nature of the impingement filter and minimal maintenance requirement makes it an attractive alternative to the conventional fibrous type filter in mining applications. The research also proposes a term called ‘filter performance factor’ to compare the performance of different filters under similar operating conditions.

Sep 19, 2020

By C. Chapman, M. G. Reading, M. P. Amsden

Ecstall Mining Limited, a subsidiary of Texasgulf Incorporated, operates the Kidd Creek mine, a 10,000- tpd base metal producer, near Timmins, Ontario. Two different ore types are mined and milled copper-zinc and silver-lead-zinc. At the highly automated Ecstall concentrator, the ores are processed by selective flotation in three individual circuits. One of the most important metallurgical tools for process control is a sample system incorporating continuous onstream X-ray analysis. Recently this system was further automated by adding computer control of reagents for two copper-zinc flotation circuits. The computer programs, utilizing optimum seeking methods and smelter contract terms, have increased copper recovery 0.8% and zinc recovery 1.6%, and reduced reagent costs by 12%. Although not anticipated, copper and zinc concentrate grades were improved modestly as well.

Jan 1, 1973