Search Documents

By D. A. Norrgran

The term "secondary recovery" has recently brought on a new meaning in view of the depletion of natural resources, energy conservation, plant optimization, and the environmental consciousness that has led to hazardous waste management, recycling, and secondary processing. Many secondary recovery processes are being developed applying mineral processing technology. Gravity separation, magnetic separation, and flotation have all emerged as implicit methods for recovering residual values from various process streams and hazardous constituents from waste streams. Recently, a technique for concentrating metallics has been successfully reintroduced. Although the concept of the eddy-current separator was developed over a century ago, (Patent 400317 issued to Thomas Edison on March 26, 1889) it was not until this last decade that it gained prominent acceptance. The evolution of permanent magnets has provided a cost effective alternative for the generation of high intensity magnetic fields. High energy permanent magnets have substantially reduced the capital and operating costs over the electromagnetic circuits employed in antecedent eddy-current separators. Specifically, in recent years, the strength of permanent magnets has increased several fold with neodymiun-boron-iron rare earth magnets now providing an energy product of 35 million gauss-oersted. Figure 1 shows the evolution in the strength of permanent magnets. The development of these rare earth magnets has led to the design of circuits possessing a magnetic force an order of magnitude greater than that of conventional permanent magnetic circuits.

Jan 1, 1991

By R. Hawker, P. Singh, K. V. Jessu, P. C. Pinazzi, A. J. S. (Sam) Spearing

Rock bolts are highly important underground to prevent falls of ground and thus, ensure safety. In situ, the ground reinforcement is subjected to a combination of loads, such as shear, tensile, and/or bending loads. Studies have been conducted to evaluate the effect of either shear, tensile, or bending loads on the ground support. However, only a few studies have been done to evaluate the effect of combined load on the rock bolt performance. In situ, the order of loads acting on the bar cannot be predicted, and more than one load can act on the bar at the same time. Thus, a hybrid failure criterion was developed that covered all combined loading conditions. Fifty-eight un-grouted laboratory rock bolt tests were conducted in total under two load conditions: applying shear displacement to the rock bolt and then tensile load to failure, and applying tensile displacement to the rock bolt and then shear load to failure. From the test results, the failure criterion was developed based on regression analysis. A nonlinear relationship was determined for the loading condition variations. The failure criterion presented in this paper can be used as a guide in the rock bolt capacity design under all loading conditions.

Sep 8, 2020

By L. G. Jones

An approximate method of calculation is developed in this paper which allows duplication of radial unsteady-state gas flow computer results where Darcy's law applies, such as those reported by Aronofsky and Jenkins and Bruce, Peaceman, Rachford, and Rice. Moreover, the new calculation method can be used to obtain results for radial unsteady-state gas flow obeying the quadratic flow law proposed by Duwez and Green. Means are discussed for predicting well behavior at single or superimposed flow rates in finite or infinite reservoirs, determining reservoir rock properties from well-test data, reproducing and interpreting back-pressure test data, and determining the radial extent and reserves of gas reservoirs from well-test data. Example calculations are presented for gas flow following both Darcy's law and the quadratic flow law. INTRODUCTION Since the publishing of U. S. Bureau of Mines Monograph 7,1 most gas-well testing methods have been based on the equation q = y (pl2 - pw2)a, where q = production rate, pl and pw, are formation pressure and sandface pressure, respectively, and y and a are constants to be obtained from test data. These methods, used for predicting both deliverability and "open-flow" capacity of gas wells, have been useful and accurate in many cases but unsatisfactory in others. Even at best, however, they do not supply information about the formation or lead to an understanding of nonsteady-state gas flow in porous media. Many theoretically based studies2-4 of gas flow obeying Darcy's law have been made.' Since the partial differential equations which result from combining Darcy's flow law with the continuity equation are nonlinear, most of the published research consists of either numerical solutions or analytical solutions for linear approximating equations. Such solutions have been of limited value in field work due to their unhandy form and their failure to correlate most field data. There is evidence5,6 which indicates that Darcy's law is inadequate to describe gas flow at some flow rates of practical interest. A quadratic flow law: which reduces to Darcy's law at low rates, is more successful in accounting for experimentally observed behavior. This flow law has been applied successfully to a few hypothetical reservoir cases in work which has recently been published.10 However, these numerical solutions of the equations involved have been successful only on a special analog computer. Routine applications to field cases would be awkward and have not been attempted. The present paper describes an approximate method for computing nonsteady-state gas flow solutions which has been completely successful in predicting the results for both Darcy flow and quadratic flow obtained by elaborate numerical methods. The new calculation method allows determination of the observable variables in gas-well testing at constant rates. It is similar to the scheme of using a succession of steady states suggested by Muskat7 in that it makes use of steady-state and material-balance equations. It also is similar to the work of Aronofsky and Jenkins2 in that the new method includes Aronofsky and Jenkins' stabilized flow equation as a special case. It improves upon both of these calculation schemes in that it accurately describes all portions of reservoir history and suggests means of determining reservoir rock properties from well-test data. This paper deals only with production from a reservoir, in which case the rate is defined as being negative. The reservoir studied here is a homogeneous, disk-shaped porous body of uniform thickness, with all boundaries sealed except the inner radial boundary of the well.

By Alice M. Chieruzzi

This Country Documentation Report presents the development of economic indices for the Philippines for the period from 1970 through 1981. The work was done through the Bureau of Mines, Minerals Availability Program, under Contract number J01225001. This contract calls for the development of twelve index time series describing factor input costs in the mining sector of 95 countries. The twelve index time series describe the costs of: 1) mining wages, 2) construction wages, 3) equipment and repair parts, 4) bits and related steel, 5) eimber and lumber, 6) fuel, 7) powder and balsting agents, 8) tires, 9) construction materials, 10) industrial materials, 11) transportation, and 12) electrical power. These indices combined with weight factors being developed by the personnel of the Minerals Availability Field Office (MAFO) of the Bureau of Mines in Denver, Colorado, will be used to perform instantaneous updates of all costs relating to the mining industry. The indices were developed primarily for use in the Bureau's Minerals Availability Program in assessing the worldwide availability of nonfuel minerals.

Jan 1, 1983

By W. Collingwood, K. V. Raj, S. Bandopadhyay

In the mining industry, computational fluid dynamics (CFD) modeling is used extensively to simulate air flow in underground mines. CFD modeling of pollutant transport in openpit mines is relatively new. Modeling the actual pit geometry of an openpit mine and the open domain is complex. The complexity is primarily due to the faceted geometry of an openpit mine with its numerous associated sharp features. Important issues that are not considered carefully at the geometry level are generally propagated to the subsequent processes. Several challenges and pitfalls are encountered in modeling pollutant transport in openpit mines. These challenges and pitfalls are related to the geometry, meshing, boundary conditions and turbulence modeling parameterization. An appropriate mesh selection is critical. A detailed discussion of the meshing of the domain of an openpit mine is presented in this paper. The selection of an appropriate turbulence model, such as kappa-epsilon (κ-ε), large eddy simulation (LES), Reynolds stress model (RSM), etc., to obtain the best possible solution is equally significant. This paper discusses the various challenges in modeling the pollutant transport process in an openpit and some of the approaches adopted to address these challenges.

Jan 1, 2013

By R. L. Bailey

"The Acheson D-3 Pool was discovered in August 1950, and contains 88 producing oil wells on 40 acre spacing. Initial oil-in-place was 118 million stock tank barrels and initial well potentials averaged 2,000 barrels per day.In early 1956 studies of hydraulic interference between the Acheson and Leduc D-3 Pools were conducted on the Carter Petroleum Reservoir Analyzer. These studies indicated that the natural water drive to Acheson would be incapable of replacing reasonable withdrawal rates over the life of the pool. To avoid shrinkage losses a scheme of pressure maintenance by water• injection was therefore instituted in March 1957.This pressure maintenance scheme is notable because pressure is being effectively maintained by high volume injection through one well located on the flank of the pool. Close control on reservoir behaviour is maintained by regular bottom-hole pres-sure surveys and observation of water cuts on producing wells. No evidence of pressure gradients or channelling of the injected water has been observed to date, and the water-oil contact has remained level over the whole field. It is possible to control the average reservoir pressure within very close limits by varying the rate of fresh water injection.Ultimate recovery estimated from the rise of the oil-water contact and calculated water influx to December 31, 1958, is 335 barrels per acre foot, or a total of 91.4 million barrels from the pool. This compares to 217 barrels Per acre foot or a total of 59.4 million barrels indicated from laboratory test data."

Jan 1, 1961

By Emre Karakaya, Niyazi Bilim

Boreholes are used for many purposes in mining operations, petroleum engineering, and construction works. Numerous factors affect the performance of drilling equipment. Researchers continue to work on the variable drilling parameters that can be adjusted in order to reach more efficient drilling operations. Penetration rate is an essential indicator in drillability analysis and estimating. This parameter is of great importance in mining projects. There are almost no models that can estimate the penetration rate for core drilling operations. Under the abovementioned circumstances, this paper focuses on developing models that allow estimating the penetration rate based on rock material properties. During the conduct of this study, drilling experiments under 11 different pressure forces were performed on 8 different rock units, and the equations which estimated the penetration rate depending on the physico-mechanical properties of the rock samples were derived. Experiments were carried out under different pressure forces to investigate the effect of the pressure force on the derived estimation models. The obtained results allowed deriving equations that ensured estimating the penetration rate based on the physico-mechanical properties of the rocks and the applied pressure force. Using these equations, the penetration rate in core drilling operations can be estimated.

Sep 30, 2020

By S. q. Honingh, G. Van Weert

Currently produced zinc-enriched blast furnace dust is stored on site at CORUS IJmuiden. To end this practise, a research program was started in 1996. Four technologies were studied: oxidative autoclave leaching in a chloride medium, fluid bed pyrohydrochloridisation (pyrohydrolysis) to yield lead-zinc-free (hematite) calcine, EAF (plasma) smelting/zinc fuming, and incorporation of the dust in 'iron foundry cupola charges. All aim to remove zinc and lead, recycle the iron residue internally, and produce a saleable zinc-lead product.

Jan 1, 2000

"Caterpillar has developed the Cat GH800B longwall plow system, designed for mining very low coal seams at high rates. Building on the attributes of the proven GH1600 plow system, the Caterpillar longwall team in Lünen, Germany, worked with the German Ibbenbüren Mine to design and construct a system for mining an anthracite seam averaging only 0.85 m (33.5 in.) thick. The result is the GH800B plow and associated longwall system, which is now operating in the Ibbenbüren Mine - where the seam does not exceed 1 m (39 in.) in height.The Cat GH800 plow, with an installed power of 2 x 400 kW, has been the plow of choice for seam heights from 0.9 to 2 m (35 to 78 in.), regardless of seam inclination or coal hardness. But the lower the coal seam, the more difficult the extraction process. Flexibility, reliability, efficiency and serviceability of the whole system had to be refined for maximum productivity in such a minimal height, but several key modifications led to success.The armored face conveyor (AFC) modifications for the GH800B plow system include PF4 plow line pans with a replaceable top trough and a new plow guide made of a one-piece casting to provide extra strength and durability while being lower in height than the previous welded version. External dogbone connectors between the line pans and a strong and flexible relay bar between the AFC and the roof supports (shields) further adapt the conveyor for very low seam operation. To increase coal throughput, the engineering team widened the conveyor crosssection with extended side plates."

Jan 1, 2014

By Peter Moser, Finn Ouchterlony, José A. Sanchidrián

"Blast fragmentation data in the form of percentile fragment sizes as function of specific charge oftenform a set of straight lines in log(size)-log(energy) space that tend to converge on a common focal point.Single-hole shots in specimens of virgin material clearly show this and the phenomenon is called the fragmentation-energy fan. Field data from bench blasting in rock scatter much more but may be interpreted to form such fans. The slopes values of the fan lines depend primarily on the percentile level. This property can be derived from sieving functions of the form P[ln(x/xmax)/ln(xmax/x50)]. An example is the Swebrec function when the parameter b is constant."

Jan 1, 2017

By Michael Rieber

A new mode of coal transportation based on the principles of pneumatic conveying has been recently, proposed by Soo, et al. [5]. Pneumatic transport is not a novel concept and commercial experience with pneumatic pipelines for short haul distances is plentiful. The list of applications is long and includes transporting ores, chemicals and pharmaceutical products, agricultural products, and domestic and industrial wastes. The study by Soo, et al. [5] updated an earlier one [l0] and presented the most recent economic evaluation of pneumatic transportation of coal. Their preliminary study concluded that there are immediate advantages for short-distance transport (less than 100 miles) and that it is both technologically and economically feasible. That study also concludes that pneumatic transport has a higher potential and more promising profitability in long-distance applications than rail if new track and roadbed must be built. Some of the advantages of long and short distance pneumatic pipeline transport of coal compared to rail and slurry transport are: 1) Replacement of diesel fuel consumed by unit trains, as the pipeline can be powered by coal-generated electricity; 2) Reduction of the skilled-labor costs required for upgrading and maintaining railroads; 3) Elimination of signaling, rerouting and overpass costs due to increased rail traffic on' mainline trackage;

Jan 1, 1977

By Lawrence Addicks

T HIS has been a most momentous year in the annals of the Institute. We have been in the midst of a situation which, were it not for the convulsions of social unrest with which life is surrounded on every side, would have attracted the attention of the world at large. I do not refer to the desperate campaign for new members. That has gone on much as usual except that, this being leap year, the annual proposal to the M. & M. Society has been omitted. Nor do I refer to the desperate situation which we found in other directions, the spread of Bolshevism, the burning of the Engineers' Club, the fact that the selling of copper appears to have become one of the lost arts. No, I speak of the great question which has to be. settled once and for all, as to whether this great Institute should adopt simplified spelling. The whole trouble started in the ranks of the California Hysterical Society. It appears, while most of the San Francisco members can read and write, several of them cannot spell. It also appears that the Secretary, in editing the Transactions, has perhaps made just a little bit too much of a point of employing the correct Stoughton idiom. At any rate, the rebels filed an amendment to the constitution, and the stage was set for civil war, with perhaps more stress on war than on civil.

Jan 1, 1920

By Jeffrey Hedenquist

The Lepanto and Victoria epithermal deposits contain in excess of 8 Moz Au, associated with massive enargite-cemented breccia and quartz-carbonate-base metal veins, respectively. The two deposits are separated by 500 m, but the latter was not discovered until the former was nearly mined out. The sulfid assemblages of these adjacent deposits are characterized by high- and intermediate-sulfidation states, respectively. However, gold was introduced after enargite at Lepanto, associated with an assemblage that is similar to that of the Victoria ore. An even larger gold resource is present in similar to that of the Victoria ore. An even larger gold resource is present in the Far Southeast porphyry Cu-Au deposit, the top of which lies 200-400 m beneath and adjacent to these two epithermal deposits.

Apr 24, 2001

By D. J. King

The development in recent years of a fluidized bed system for use as a counter-current solid ion exchange loading contactor for the purification and concentration of uranium from leach liquors has had a major impact on the design of uranium extraction plants. The main object of this paper is to describe many of the variations that can be applied to the design of uranium extraction plants arising from the use of a fluidized bed loading contactor with a view to providing a guide for the development of a flowsheet for a new uranium extraction plant. The paper has been devoted primarily to the consideration of conventional uranium extraction plants in which a ground ore is leached in mechanically or air agitated tanks. The effect of the use of a fluidized bed loading contactor on each of the plant sections from leach to uranium purification and concentration has been considered. In order to describe most effectively the impact of using a fluidized bed solid ion exchange loading contactor, its use has been compared with the performance that can be achieved with the most common alternative purification processes. The comparisons are made largely on a technical basis, but the effect on the capital and operating costs of the different uranium extraction flowsheets are described qualitatively. In making these comparisons, consideration is given to the effect on the size, number and materials of construction of equipment items and how the quantity and composition of the liquid effluents can be controlled to reduce the environmental problems arising from the disposal of these effluents. The paper also discusses some of the factors that should be taken into consideration in the design of a fluidized bed loading contactor and describes various designs of the elution section that can be used in conjunction with the loading contactor.

Jan 1, 1979

By Amila Sandaruwan Ratnayake, T. Dilmi. U. Wijewardhana, H. C. S. Subasinghe

The value addition potential of ilmenite was examined using several characterization techniques. Raw ilmenite is composed of 93.65 wt.% of FeOTiO2, 3.55 wt.% of SiO2, 1.22 wt.% of Al2O3, and the remainder being other minor oxides. Ilmenite and powdered carbonized coconut shells were mixed in the weight ratio of 4:1. A separate fraction of the same mixture was added with powdered seashells in the weight ratio of 4:1:0.5. Six fractions of each mixture were distinctly milled from 1 to 6 h in a planetary ball mill. XRD spectra (broadened and diminished reflections of ilmenite) and FTIR observations (Ti―O―Cbonding) of milled samples indicate the possible incorporation of carbon into the ilmenite structure. Any clues of an occurrence of new rutile peaks were not observed in XRD spectra of milled samples. Consequently, the carbothermic reduction has not been initiated during mechanical activation. In this case, samples powdered for 6 h in a mill were isothermally annealed for 2 h under normal airflow at temperatures of 800 °C, 1000 °C, and 1200 °C, respectively. According to the X-ray diffractograms, the annealing temperatures of 1000 °C and 1200 °C exhibited almost similar trends with rutile (R), pseudobrookite (PB) and elemental iron (F), and a very few ilmenite (I) peaks. Consequently, 6 h of milling and 1000 °C annealing were concluded as the optimum conditions for the carbothermic reduction. Moreover, this study indicated seashells as a potential rate raiser for the carbothermic reduction of ilmenite at 800 °C. Therefore, this process is applicable to upgrade ilmenite into a mixture of synthetic rutile and elemental iron.

Mar 29, 2021

By James P. Hambleton, Anastasia Nally

This work focuses on the numerical simulation of multi-plate anchor systems (e.g., helical anchors) in sand subjected to vertical loading. In assessing the stiffness and capacity of these multi-plate anchor systems, full awareness of the abilities and limitations of the various analysis methods must be understood. This work first summarizes studies completed by others and then goes on to assess the failure mechanisms of multi-plate anchors in sand and the influence of (1) plate width-to-depth ratio, (2) number of plates, and (3) relative positioning of plates. The analysis makes use of (1) conventional limit analysis, (2) so-called modified limit analysis that employs reduced strength parameters to account for the influence of soil dilatancy, and (3) the displacement-based finite element method, which considers elastic as well as plastic deformation leading to failure. The work critically reflects on limitations in the current analysis methods for helical ground anchors. INTRODUCTION Helical anchors are a relatively low cost foundation type, typically consisting of a steel rod and single or multiple plate attachments. In recent decades, they have seen rapid growth, and as outlined by Merifield and Sloan (2006) and Hambleton et al. (2014). Design techniques for helical anchors have previously been predominately empirical, as much of the past research in this field is experimentally based. It is common practice for helical anchors to be modeled as horizontally oriented plate anchors in both numerical and experimental analysis. This work focuses on analysis based on the finite element method, including so-called finite element limit analysis and the conventional displacement-based finite element method, with some comparisons made to experimental studies. Numerical simulation of anchor pull-out capacity in cohesionless soils is stunted by the many difficulties faced when using numerical analysis with cohesionless soils. Additional variations can be seen when comparing the serviceability based load capacities to the ultimate load. In this work, both the force-displacement response (stiffness) and the ultimate anchor capacity are assessed, with more focus on the latter. This work focuses only on analysis techniques for multi-plate anchors with vertical loading in cohesionless soils. Many studies have been completed in this area, some of which assume a rectangular plate in a plain strain model (Rowe & Davis, 1982; Merifield & Sloan, 2006; Cerfontaine et al., 2019). Whereas others use axisymmetric conditions (Baker and Kondner, 1966; Saeedy, 1987; Murray & Geddes, 1987; Ghaly & Hanna, 1994; Sakai & Tanaka, 1998; Merifield et al., 2006;) and minimal studies considered both axisymmetric and plane strain in the one study (Vesic, 1971; Tagaya et al., 1988; Murray & Geddes, 1987; Sarac, 1989).

Jan 1, 2019

By M Fitzgerald

Fimiston Open Pit is operated by Kalgoorlie Consolidated Gold Mines (KCGM) as a joint venture between Barrick Gold and Newmont Mining. Over 110 years of underground mining resulted in the development of nearly 3500 km of underground workings including backfilled and open stopes up to half a million tonnes in size. These voids significantly complicate blasting processes at KCGM, influencing blast movement direction and magnitude. Blast movement monitoring to improve mine reconciliations was identified as an improvement project in the business plan for the geology team in 2008. Following successful trials in 2008 to 2009, blast monitoring and translation of ore blocks were implemented as a permanent grade control program from late 2009 and is now part of the Management Operating System (MOS) of the mine. This paper presents a summary of results from the Blast Movement Monitoring (BMM®) data collected to date. Ore blocks at KCGM are translated primarily using BMM® data. This data is obtained from the BMM® system which measures the movement of a radio transmitter installed in a blast pattern from a preblast position to a post-blast position. The application of the data collected by the BMM® tends to be both mine site and blast specific. At KCGM, an average distance obtained from the BMM® data within a given shot is the primary method used for translation. In the case that BMM® data is unavailable, a theoretical movement vector established from Orica Shotplus with distances gained from the historical BMM® database is used. Data is presented in an ore loss and dilution exercise for a bench undertaken at KCGM to understand the potential effects on reconciliations. Improvements that have flowed from implementing blast monitoring include improved reconciliations when combined with other grade control improvement projects. The increase in liaison between the geology and blast personnel at KCGM has been a significant improvement gained from the implementation of the blast monitoring program. This has allowed a better understanding of blast movement and the effects on ore dilution and ore loss by the mine geology team. In addition, the discussion of blasting tie-in plans between geology and blasting personnel has been improved which leads to more favourable blasting practices that take ore movement into account.

Aug 22, 2011

By Y. Gordon

ABSTRACT A methodology based on a two-stage approach was developed for process technology selection. The first stage includes evaluation of available technologies, followed by shortlisting the best technologies based on mass and energy balance modelling, financial analysis, and risk analysis. The second stage involves detailed analysis using refined input data, mass and energy balance modelling, and capital and operating cost estimation, as well as a more detailed financial analysis. A case study covering the selection of ironmaking technologies for a company in the Russian Federation is presented to illustrate the critical elements of the methodology and the analysis process.

Jan 1, 2014

By Paul R. Thomas

The Bureau of Mines evaluated the impact of the depletion allowance upon the economic availability of copper from domestic deposits. The potential long-run percentage depletion deduction, cumulated over the life of the properties, was estimated at approximately $2.5 billion for producing properties and up to $11.7 billion for nonproducers. The income transfer, in the form of higher Federal income tax payments if the allowance were repealed, was estimated at $1.5 billion for producing properties and up to $8 billion for nonproducers. The percentage depletion allowance, through its role in determining Federal income tax liability, was found to be very significant in affecting profitability. Repeal of the allowance could result in major domestic copper availability reductions at all price levels, now and in the future, as a result of reduced profit margins for current producers, and postponement of development decisions for nonproducers. It was demonstrated that a 50-percent reduction in the percentage depletion rate applicable to copper would also result in a significant decrease in profitability for nonproducing properties. For producing properties, the percentage depletion rate on copper was shown to be less significant than the income limitation that is placed upon the total amount of the depletion deduction. Repeal of the minimum Federal tax provision was shown to be significant in enhancing profitability for both producing and nonproducing deposits. The report concludes that the percentage depletion allowance operates as an important method of capital recovery and production incentive.

Jan 1, 1982

By M. K. Larson, J. K. Whyatt

Proper employment of numerical stress analysis design tools is based on the demonstrated ability of a model to capture key elements of the geologic site model and accurately simulate how these elements interact with a mine design. While these tools have progressed markedly, they are, at heart, a gross simplification of the abundant complexity of a natural setting and its response to mining. A generic deep longwall site model was developed that includes aspects of the geology of deep coal mines in the Wasatch Plateau and Book Cliffs coal fields of Utah. The site model contains a set of common features and observations of how these features typically respond to mining. This site model was the basis for evaluating use of empirical, boundary element and volume element stress analysis tools to analyze the distribution of stress around a deep longwall panel. More specifically, this evaluation examined shifting of stress to panel abutments and gob, distribution of stress in the abutment and deformation and failure of bridging strata. Measurements of abutment stress changes at two sites in the Wasatch Plateau region were used to illustrate model calibration. Overall, these comparisons highlight the considerable differences between methods. Volume element tools can incorporate considerable detail and have fewer underlying assumptions, but this detail carries a considerable computational cost. Boundary element tools are much more efficient. However, this efficiency comes at the cost of added assumptions. These assumptions were challenged by the presence of a strong sandstone unit in the overburden, leading to boundary element results that depart significantly from volume element results. Empirical rules are the simplest, but are even more burdened by assumptions, many of which are implicit in underlying cases. Insight into the nature and impact of underlying assumptions in each method is essential to the proper use of results in mine design.

Jan 1, 2009