Search Documents

By Andrew A. Cochran

Laboratory-scale research was conducted by the Bureau of Mines to develop a new process for treating electroplating and other wastes. Various acid and alkaline cyanide wastes were combined under controlled conditions to neutralize the wastes and to almost completely precipitate the metals and cyanides. The metals were subsequently recovered for recycling; the cyanides can also be easily recycled. The process was successfully used to treat the major types of electroplating and etching wastes, containing Cd, Cr, Cu, Ni, and Zn, and to treat both concentrated and dilute wastes. The economic aspects of treating concentrated electroplating, etching, and anodizing wastes are especially attractive because of the low cost of mixing two wastes, the high value of the recovered metals, and the simplicity of the recovery procedures. The filtrates from the waste-plus-waste step were relatively harmless compared with the original wastes and met Public Health Service standards for free cyanide content. Free cyanide ions were not detected in most of the filtrates; the limit of detection was 0.03 ppm. Only small amounts of HCN were produced during the neutralization; the HCN was collected and neutralized.

Jan 1, 1974

By R. Perlo

"INTRODUCTION Peoples’ and operators’ safety in construction are tightly linked to the engineering choices, as much as the necessity of reducing time and costs of realization. Therefore, it is of paramount importance to address them properly from the earliest stage of the design, identifying the risks connected to the work and the variability of such during the different phases of the project. Risk is often measured as the expected value of an undesirable outcome. Regarding to occupational safety and health, the risk is the likelihood that a person may be harmed of suffers adverse health effects if exposed to a hazard. This combines the probabilities of various possible events and the assessment of the corresponding harm into a single value. However, the actual occurrences are often more complex than a single binary possibility case. In a real case scenario, with several possible accidents, the total risk is the sum of the risks for each different accident, provided that the outcomes are comparable. The semi-automatic tunnel support system along with its erector machine proved to be a solution with improved structural performance, able to reduce the time and yet to deliver an enhanced, quality-aware and safer working environment for the operators. The implementation of the system provides the engineers, the contractors and the owners with an effective alternative option shortlisted in 2015 for the ITA Award for the Safety Innovation of the Year. In a market industry driven by safety and time constrains the efficiency shall be the ultimate goal, in order to provide solutions able to negotiate with the most challenging ground conditions. In this paper, the authors describe the recent developments on regard of this whole new tunnel support system, including design approach and presenting related case histories OFFSETTING THE RISKS Considering the above factors, from the manufacturers’ point of view, an effective way to limit the construction risks is to focus on the material and technological characteristics, their application and the risks related to them including any residual risks. Finally addressing the construction needs also involves time and cost-effective solutions. The path to follow is an integrated approach where the efficient management of the risk is supported by a flexible, user-friendly, and time effective product that is able to provide a safe, reliable and viable solution to address the construction requirements. Therefore, in a market sector driven by safety and time constraints, the efficiency is a key goal, in order to avoid redundancy and yet to deliver a safe working environment able to meet the construction schedule. The safety of all the parties involved is given by stable working conditions, either for the workers, or the operators and eventually the public. Therefore, the solutions provided should ‘strengthen’ the overall condition and such “to limit or to reduce the deformations within acceptable designed limits and to prevent [the tunnel] to collapse” [1: Clause 207.1.4]."

Jan 1, 2018

By David G. C. Robertson

A new approach is described for the calculation of the kinetics of metal/slag, metal/slag/gas, and metal/matte/slag/gas reactions. The algorithm assumes that equilibrium is achieved at the interface between phases, and uses an equilibrium solver (such as SOLGASMIX) to compute the equilibrium state at the interface at each time step during the reaction. For multiple phase systems a number of unit operations, representing the different phases and interfaces, must be connected together in a reasonalbly complex manner, and the METSIM software package has been utilized for this purpose. The new approach is superior to the SMAK software developed by the author and his co-workers over the past decade, for the reasons discussed in this paper.

Jan 1, 1995

By P Joyce, D R. Cooke

The Dinkidi Cu-Au porphyry deposit is situated in the Caraballo Range of North Luzon, Philippines. Although comparatively small, Dinkidi has unusually high gold grades with drilling by Climax-Arimco Mining Corporation delineating a 110 Mt orebody at 1.2 g/t gold and 0.5 per cent copper. The magmatic-hydrothermal evolution of Dinkidi records a distinctive switch in mineralisation from an early orthoclase-dominated Au-rich assemblage, typical of alkaline porphyry systems, to a later quartz stockwork Au-Cu rich assemblage typical of most calc-alkaline to shoshonitic porphyry systems. The early orthoclase-dominated stage is associated with the intrusion and crystallisation of a variably-textured clinopyroxene-syenite dyke that contains high-grade (5 - 20 g/t) gold mineralisation. We consider this dyke to be a Cu-Au porphyry analogue to the pegmatites found in granitic systems. Dinkidi is hosted within the Early Miocene Didipio Igneous Complex. This alkaline igneous complex is comprised of early unmineralised gabbros (pyroxene-plagioclase cumulates), clinopyroxenites (pyroxene cummulates), diorites and monzodiorites that have been intruded by a large, weakly mineralised monzonite pluton. The Dinkidi deposit is located at the southern margin of the monzonite pluton. Mineralisation is hosted within a composite monzonite stock. Within the stock, an 800 metres by ~200 metres (plan section) elongate monzonite stock (Tunja Monzonite) predates and hosts the bulk of the Au-Cu mineralisation. This has been intruded by the thin (10 to 30 m wide), highly mineralised variably-textured magnetite- and clinopyroxene- phyric syenite pegmatite (the Balut Dyke). The youngest phases of the composite stock are leucocratic quartz-monzonite porphyry (Quan Porphyry) that grades texturally, in its core, into a post-mineralisation crystal-crowded quartz-syenite (Bufu Felsite). The late-stage Bufu Felsite is inferred to be the source of much of the Cu-Au mineralisation. The Didipio Igneous Complex has intruded a sequence of Late Oligocene alkaline andesitic lavas and volcaniclastics and overlying potassic dacitic lavas. Whole rock geochemical analyses indicate that the intrusions and the potassic dacite lavas in the surrounding region are co-magmatic. Five main stages of hydrothermal activity are recorded at Dinkidi. An unmineralised K-silicate (biotite-magnetite) alteration assemblage formed during the intrusion of the Tunja Monzonite stock. The diorites surrounding the stock display intense selectively pervasive biotite and magnetite alteration and are cut by an extensive network of orthoclase veins and monzonite dykes. The orthoclase-dominated assemblages of Stage Two carry substantial high-grade Au mineralisation and are associated with the intrusion of the Balut Dyke. The emplacement of this unusual dyke is associated with emplacement of pegmatitic clinopyroxene-orthoclase-magnetite¦sulphide dykes, localised orthoclase flooding along the margins of the dyke, and subsequent emplacement of an extensive orthoclase-actinolite-bornite¦chalcopyrite-fluorite stock-work, and development of widespread selectively pervasive actinolite alteration. The main stage of Au-Cu mineralisation at Dinkidi is intimately associated with the intrusion and initial crystallisation of the leuco-monzonite porphyry (Quan Porphyry) and emplacement of a quartz stockwork followed by carbonate-sulphide deposition and intense vein-related sericite and carbonate alteration assemblages. The quartz stockwork formed synchronous with the deposition of the æBugoy QuartzoliteÆ, a very coarse grained mosaic of quartz-orthoclase-perthite along the walls and top of the crystallising intrusion. Stage 3 was terminated by crystallisation of the distinctively vuggy Bufu quartz-syenite phase in the core of the intrusive, with associated antiperthite veins, and the subsequent explosive brecciation of the roof of the intrusion, forming a quartz-fragment breccia from the Bugoy Quartzolite. Retrograde metasomatism during Stage Four was intimately associated with the emplacement of extensive, late-stage carbonate, silica and zeolite veins and widespread selectively pervasive carbonate alteration. The last hydrothermal stage at Dinkidi, Stage 5, is comprised of strong selectively pervasive clay alteration and is associated with fault-related brecciation of the Dinkidi stock.

Jan 1, 1999

By William Gregg

Recent environmental and workplace safety legislation has Imposed more stringent limits on the amount and type of particulate emitted Into the air. In the past, the mass of particles contained In a volume of air was the governing criteria. Now the size and precise chemical nature of the particulate must be known and controlled In addition to it's ?mass. Processors of metallic materials have to implement stricter control practices and more efficient control equipment to meet the new regulations. Pulse-Jet dust collector systems are being used to control particulate emissions from various process gas streams. Pulse-jets :are also being used for maintaining a healthy environment In the workplace. this paper will discuss the impact of these regulations, the control techniques used to comply with such regulations, and the equipment needed for compliance.

Jan 1, 1992

By T Elms, R Beckman, M Sampson

"In today’s mining industry, the pressure of reducing costs and increasing production while maintaining high safety standards is at the forefront of operational endeavours. A combination of specific mining knowledge and technological advances has helped enable this notion. Fleet management systems have been developed to enable sites to better measure and manage production to improve operational efficiency.The integral part to managing production is having accurate, readily accessible data. This empowers key stakeholders in the management team to drive production reporting, materials tracking and budget forecasting.If a site does not run a fleet management system, manual input is heavily relied upon for production data, which introduces increased risk of human input error. Errors can drive outcomes that don’t achieve increased production at a reduced cost. Alternatively, a fleet management system can have improved accuracy but involves a high monetary investment. Such an investment is not always feasible for smaller mining operations subject to current industry cost pressures.The Emeco Operating System has been developed in alliance with sites such as the Mungari White Foil Operations by satisfying the criteria of a low intensity hardware installation, material tracking data validation processes, remote monitoring, identification of metrics to improve overall operating efficiency and providing the right information to key stakeholders.Citation:Beckman, R, Elms, T and Sampson, M, 2016. Getting Accurate Mine Information to the Right Teams to Drive Production Improvement, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 203–211 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

By James R. Finlay

SOMETIMES the American Institute of Mining and Metallurgical Engineers appears to be a strictly technical society, and if so my paper should deal with the technical operations of finding and producing gold. But I have not been engaged in practical gold mining since 1910. What I have been doing mainly for the last 25 years is to try to figure out what the income of a mine-gold, or any other-would be worth to an investor. So I have been in contact with gold mining, in one way or another, for some 42 years. I say that with a purpose. In that time the industry has been through one of its cycles. The value of gold mines is very dif¬ferent at different points in one of these cycles. For this reason the cycle of gold mining is a highly practical study. The cycle of gold is a more or less rhythmical change in its value or purchasing power measured in the grand average of other commodities, which is the same thing as its price. Taking the price of gold in 1897 as a stand¬ard, a dollar at that time declined to 55c. in 1913, to 26.8c. in 1920, and since then it has risen to 47.4c. in 1930 and to about 64c. in 1932. It is worth about 21/ times as much now as it was in 1920, but less than two¬thirds as much as in 1897. When this change is applied to the value of a gold mine still greater differences are evident. The cost of producing gold is of course measured in labor and other commodities, and as that cost goes down the margin of profit measured in the gold itself increases. Thus a mine which might make only 10 per cent profit in 1920 on its gross output may easily make 25 per cent now. The stockholder gets 2 ½ times more gold that is worth 2 1/2 times as much in purchasing power, therefore the real value of his holding has risen by the one factor multiplied by the other, giving him 61/4 times as much goods or services as he had in 1920.

Jan 1, 1933

By Jheison Lopes dos Santos

O presente estudo teve por objetivo principal produzir um cerâmico composto de alumina, nióbia e fluoreto de lítio de forma a otimizar o uso do forno na etapa de sinterização. Para isso, ponderou-se a respeito da necessidade ou não de utilização de um patamar a 1000°C utilizado em estudos anteriores. Além disso, buscou-se diminuir a temperatura de sinterização, assim como o tempo de permanência em tais temperaturas. O composto cerâmico (Al2O3–4%Nb2O5)–0,5%LiF foi sinterizado a três temperaturas diferentes (1200, 1250 e 1300 ºC), com tempo de patamar de 1h. Foi realizado ensaio de Arquimedes para analisar sua densificação e determinar sua densidade. As fases formadas nessas temperaturas foram identificadas por difração de raios-X. Os resultados mostraram que a maior densificação foi obtida para a maior temperatura, de 1300 ºC. Foi possível observar também que um patamar de apenas 1h na temperatura de sinterização de 1300 ºC apresentou igual densificação a de outros trabalhos, com tempo de patamar de 3h. Este fato sugere que a temperatura tem maior influência na sinterização do que o tempo de permanência. Verificou-se ainda que as mesmas fases foram formadas nas três temperaturas investigadas, sendo tais fases as mesmas detectadas em trabalhos anteriores com patamares maiores. Isso mostra que o prolongado tempo de 3h no patamar de sinterização apenas favorece o crescimento dos grãos, bastando apenas a permanência de 1h para alcançar os resultados desejados e com grãos menores.

Oct 30, 2017

By M-d-N. Gagnon, P. Okono, Y. Bergeron

In the mining industry, decisions regarding the type and number of comminution tests to be completed typically rely on geologists? observations and conclusions when studying drill cores. Given that these decisions are based on visual observations, they are essentially approximate and often inaccurate from a comminution viewpoint, causing a sizeable margin of error in estimating characterization test needs. Consequently, companies are often forced to perform more tests than necessary, requiring a significant quantity of material, and accruing significant costs. Recently, a new device, called the Hardness Index Tester (or HIT), was developed, offering users a low cost in-house mechanism for estimating the comminution parameter A*b and the Bond Ball Mill Work Index at any mine site, with potential applications on fragments up to 25 mm from drill core. In late 2016, Agnico Eagle Mines Limited initiated a trial to investigate if having an HIT device installed in a core repository would make it possible to identify the different rock properties more accurately and determine the number and type of comminution tests required. The application of the HIT was not to replace the standard comminution tests, but rather to generate a high number of comminution and geomechanical parameters for the rock mass. Ultimately, the objective would be to determine the uniformity of the rock mass and, therefore, easily distinguish any potentially problematic zones. With this method, the appropriate number of standard tests could be determined, making the HIT not only an excellent complement to the standard laboratory tests, but also an indispensable device for a geometallurgical characterization. This paper presents the results from the HIT trial using samples from the Odyssey Project, which is a Mine Canadian Malartic property.

Jan 1, 2017

By R. E. Siemens

A process is being developed by the Bureau of Mines to selectively recover nickel and cobalt from low-grade domestic laterites. In laboratory evaluation of the process, the oxides in the laterite were selectively reduced with carbon monoxide at temperatures from 350° to 600° C. For material containing more than about 5 percent magnesia, pyrite additions or post-reduction heat treatments were necessary to achieve satisfactory nickel and cobalt extraction for this range of reduction temperatures. Multistage leaching of the reduced material at ambient temperature and pressure in the presence of oxygen, ammonium sulfate, and ammonium hydroxide extracted up to about 90 and 85 percent of the contained nickel and cobalt, respectively. The nickel was selectively recovered from the leach solution by solvent extraction and was then stripped from the loaded organic with dilute sulfuric acid to provide a nickel-rich electrolyte. Treatment of the raffinate with hydrogen sulfide resulted in the recovery of cobalt as a sulfide. The only contaminant in solution was magnesium which was removed by ion exchange or precipitation. In this process the energy requirements are relatively low and except for minor operation losses, only coke and oxygen are consumed.

Jan 1, 1975

By Yuzhe Zhang, Matthew Andriese, Jiann-Yang Hwang, Guanghui Li, Zhiwei Peng, Tao Jiang

The microwave power absorption characteristics of iron oxides, including Fe2O3, Fe3O4 and Fe0.925O, have been studied by determining dielectric loss and magnetic loss distributions in 0.05-m-thick oxide slabs irradiated with 1.2-kW, 2.45-GHz microwaves. The results reveal that the dielectric loss is the main factor contributing to microwave absorption in Fe2O3 and Fe0.925O, while the magnetic loss dominates the power absorption in Fe3O4 below its Curie point. Uneven power distributions are observed in the slabs and this phenomenon becomes even worse at high temperatures at which the permittivity increases significantly. Quantification of power absorption in the oxides is of great importance for efficient and uniform microwave heating

Jan 1, 2015

By C Donnelly

Redpath Australia is using a unique mining method for the Australian underground coal industry at Kestrel Mine Extension in the Bowen Basin, Central Queensland.The project involves completing two separate drifts from the surface for access to the German Creek Coal Seam located approximately 230 m below the existing surface. The scope of work is primarily the construction of two drifts; the first is 1577 m at 1 in 6 gradient and the second 1874 m at 1 in 8 gradient. Each drift has been developed by a Mitsui S200 roadheader with modifications to allow for a continuous tunnelling/mining cycle operation. A shotcrete boom has been fitted to the left hand side of the machine with the operators console located at ground level. Another operators console is elevated on the right hand side of the machine to allow operation of the rotary drill boom which is mounted on a slide rail to allow flexibility of positioning depending on the stage of the cycle. In support of the roadheader activities, an integrated conveyor system mounted on a sliding floor arrangement is able to be advanced as the mining face progresses. This sliding floor consists of four 1.5 m × 6 m sections that utilise hydraulic rams to ‘walk’ inbye, allowing room for installation of precast concrete floor panels for final floor completion. This method borrows from the tunnelling and construction industries to eliminate place-change delays in the mining cycle by enabling complete ground support installation without retreat of the primary development machine from the face. The aim is to reduce the project duration with the completion of final floor and services to within 30 m of the operating face as it advances.

Mar 21, 2011

By John Ward Smith

Variations in specific gravity of oil retorted from oil shales of the Eocene Green River Formation in northwestern Colorado were evaluated statistically, demonstrating that these variations are very strongly associated with stratigraphic position and less strongly but still significantly associated with geographic location. Specific gravity of oil retorted from these oil shales apparently varies with the carboxyl group content of the oil shale's organic matter. Higher temperatures accompanying increasing depth of burial probably progressively decarboxylated oil shale's organic matter producing the decrease of oil specific gravity associated with deeper stratigraphic position. The geographically associated oil-gravity variations were probably produced by regional variation in the original thickness of late Cenozoic extrusive rocks once overlying the Green River Formation.

Jan 1, 1966

By L. Vollert

"The application of pneumatically-assisted fluidized bed flotation, specifically the ERIEZ HydroFloatTM technology, has found widespread use in non-sulphide processing (particularly phosphate, potash and coal) for the recovery of coarse particles. In gold processing, centrifugal gravity circuits and flash flotation cells are typically employed for the recovery of coarse and near-size liberated gold which tends to accumulate in recycled grinding streams due to bypass to the classifying cyclone underflow streams owing to the higher specific gravity of these gold particles. Early removal of this gold from the grinding circuits contributes toward the reduction of downstream processing losses as a result of overgrinding and particle shape deformation in the case of flotation processing, longer leach residence times in the case of extractive processing, and surface occlusions in the case of both flotation and extractive processing. Furthermore, recovery to bullion attracts higher payment terms by way of comparison to concentrate sales in the case of copper-gold concentrators. This paper assesses the application of pneumatically assisted fluidized bed flotation for the recovery of coarse liberated gold through the analysis of piloting data generated from the operation of a continuously operated 16 inch ERIEZ HydroFloatTM unit treating a sized coarse grinding circuit stream. The paper presents the stage recovery by size performance of the ERIEZ HydroFloatTM unit together with quantitative gold deportment analysis to demonstrate the efficiency with which gold was recovered during this pilot campaign and then compared to more conventional processing units – centrifugal gravity and conventional flotation.INTRODUCTION Newcrest Mining Limited (NML) has identified that an opportunity exists for improving the recovery of coarse composite particles at its current operations, both as a means for improving overall recovery and as an opportunity for early gangue rejection. As such, Newcrest Mining Limited has taken an interest in the application of pneumatically-assisted, fluidized-bed flotation i.e. ERIEZ HydroFloatTM technology. This interest dates back to 2011 with sighter testwork carried out on their Australian-held ore bodies (Kohmuench et al, 2013). Newcrest continues to assess ERIEZ HydroFloatTM potential for coarse composite recovery and, in the case of the topic of this paper, coarse gold recovery based on examples in the literature which demonstrate the efficiency of this technology in this regard (Carmona Franco et al., (2015); Miller et al., (2016); and Kohmuench et al, 2013)."

Jan 1, 2017

By Dean Brox

Tunnel boring machines (TBMs) have been used for the construction of various tunnels for mining projects for the purpose of access, conveyance of ore and waste, drainage, exploration, water supply and water diversion. Several mining projects have seen the successful and economic beneficial use of TBMs, and there is an increasing awareness of the benefits of TBMs for mining projects. Key technical considerations for the use of TBMs for the construction of tunnels for mining projects include geological issues (rock type, rock alteration, rock strength, rock abrasivity, durability, ground water inflows), depth of cover and the potential for overstressing/rockbursts, site access and terrain, portal locations, TBM constraints, minimum tunnel size, tunnel support requirements, contractor and labor experience, and project schedule demands. TBMs offer key project schedule benefits with high rates of progress, which is a unique economic advantage recognized for mining projects where timing is of the essence in order to advance mining development and achieve early startup for operations. A thorough evaluation of the anticipated ground conditions should be performed as part of the decision to adopt a TBM for a mining project. Minimum specifications for TBMs are necessary in order to prevent the incorrect type of TBM from being used. Appropriate geotechnical investigations are necessary in order to provide key information on the anticipated subsurface conditions for careful planning and design of the proposed tunnel alignment. The overall site and geological conditions associated with some projects may suggest that it is not appropriate to use TBMs for some mining projects due to a perceived higher risk.

Jan 1, 2013

By Dean Brox

Tunnel boring machines (TBMs) have been used for the construction of various tunnels for mining projects for the purpose of access, conveyance of ore and waste, drainage, exploration, water supply and water diversion. Several mining projects have seen the successful and economic beneficial use of TBMs, and there is an increasing awareness of the benefits of TBMs for mining projects. Key technical considerations for the use of TBMs for the construction of tunnels for mining projects include geological issues (rock type, rock alteration, rock strength, rock abrasivity, durability, ground water in flows), depth of cover and the potential for overstressing/rockbursts, site access and terrain, portal locations, TBM constraints, minimum tunnel size, tunnel support requirements, contractor and labor experience, and project schedule demands. TBMs offer key project schedule benefits with high rates of progress, which is a unique economic advantage recognized for mining projects where timing is of the essence in order to advance mining development and achieve early startup for operations. A thorough evaluation of the anticipated ground conditions should be performed as part of the decision to adopt a TBM for a mining project. Minimum specifications for TBMs are necessary in order to prevent the incorrect type of TBM from being used. Appropriate geotechnical investigations are necessary in order to provide key information on the anticipated subsurface conditions for careful planning and design of the proposed tunnel alignment. The overall site and geological conditions associated with some projects may suggest that it is not appropriate to use TBMs for some mining projects due to a perceived higher risk. Key words: TBM, Tunnel boring machines, Tunneling in mining

Feb 1, 2014

By F. S. Wartman

This paper gives an account of the production of ductile-grade titanium powder in 100-pound batches by reduction of purified titanic Chloride with magnesium, grinding, leaching, and magnetic-separation of the reaction product. Apparatus, technique, and methods of controlling product quality are described and some data on operating costs are given.

Jan 1, 1949

By Keith A. Heasley, Jian Yang

"LaModel uses a laminated overburden boundary-element model and can calculate not only seam-level stresses and displacements but also surface subsidence for thin tabular deposit such as coal seams (Heasley, 1998). Up to this point in time, the material property wizards in LaModel have primarily been designed for calculating accurate stress distributions in single- and multipleseam situations, and for investigating and optimizing pillar sizes and layouts in relation to overburden, abutment, and multipleseam stresses. However, the critical input parameters that will give the most accurate seam-level stress distribution do not necessarily produce the best surface subsidence prediction. The objective of this paper is to develop a methodology for calibrating the critical input parameters in LaModel to optimize surface subsidence prediction.For optimum surface subsidence prediction, it was found that the gob convergence (as defined by the final gob modulus) and the overburden stiffness (as defined by the lamination thickness) were the two most critical parameters that needed to be calibrated (Heasley, 2016). By calibrating numerous panels with various widths and depths, a formula that provides the optimum final gob modulus to use for subsidence prediction was developed. Also, three different empirical formulas for optimizing the lamination thickness as a function of overburden depth and/or the panel width to- depth ratio were determined for the three cases: supercritical panels, and subcritical panels with and without offsets. Further, if the user has measured data for subsidence factor and angle-of draw, the optimum final gob modulus and lamination thickness can be determined from the measured data. These new subsidence prediction formulas are being implemented into new material wizards in LaModel.INTRODUCTIONIn the past few decades, with the increased need for highly productive mining techniques, full extraction mining methods have been increasingly employed in the U.S. coal mining industry. These total extraction mining methods, which include both longwall mining and room-and-pillar retreat mining, normally cause immediate roof caving and the associated surface subsidence. These methods can be highly productive and cost-effective, but the associated surface subsidence can cause damage to surface structures and negatively impact the surface environment (Peng, 2008). Therefore, a reliable program for predicting the surface subsidence associated with full extraction mining is required for appropriately engineering and managing the surface subsidence impacts of full extraction mining."

Jan 1, 2016

By A Jewbali, R Perry, R Inglis, L Allen

"The use of conditional simulation to characterise mine plan uncertainty is increasing for the assessment of risk in mining projects. While the development of grade uncertainty profiles is relatively straightforward and can be validated using standard geostatistical techniques, the addition of geological uncertainty to evaluate total risk remains problematic. Some of the problems associated with geological uncertainty methods include the clustering of data in favourable geologic units, difficulty in training image definition and the inability to address change of support issues for categorical variables. Despite these obstacles, the importance of geological uncertainty as a contributor to total uncertainty has prompted Newmont to explore and evaluate the use of various techniques (and combinations of techniques) on different deposit types.Two orogenic deposits of different geological complexity were selected for the study: Subika, a shear zone-hosted deposit, and Merian, a deposit containing gold mineralisation associated with quartz vein zones and stockwork within which are found higher-grade quartz breccia zones. Newmont trialled various categorical simulation approaches to determine the applicability of these methods for each deposit type and the effect of parameter choice on the width of the uncertainty interval. Some of the techniques that were trialled include multiple point statistics methods, sequential indicator simulation using local probabilities as well as variations of these methodologies.The goals of this study included: gaining an understanding of which techniques may work best in which deposit types gaining an understanding of the intricacies of each method gaining an understanding of the effect that each method has on total uncertainty analysis.This paper presents a comparison of the various techniques and makes recommendations for their use in uncertainty analysis.CITATION:Jewbali, A, Perry, R, Allen, L and Inglis, R, 2014. Applicability of categorical simulation methods for assessment of mine plan risk, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014, pp 85–98 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 24, 2014

By K. J. Stanaway

Environmental pressures on waste disposal are forcing pigment producers to use higher content TiO2 feedstocks with lower levels of trace elements. Despite this, 50% of the worlds TiO2 comes from ilmenite concentrates with only 37 -54 % TiO2 An industry growth rate of 25 % in the next ten years combined with trends to diminishing resources and lower grades for rutile (95 % TiO2) and leucoxenized ilmenite (55 to 90% TiO2) mean that unless new discoveries are made soon, the industry will become even more reliant on ilmenite. A hypothetical ideal feedstock is presented and strategies to obtain it are suggested. Reasons for some of the mineral specifications are given.

Jan 1, 1994