Search Documents

By K. T. Menzies

This report documents laboratory and in-mine analyses of diesel exhaust pollutants carried out to assess the fate of potentially reactive species in the mine environment. Specifically, the concentration of stable compounds including carbon monoxide and carbon dioxide, and potentially reactive compounds including nitric oxide, nitrogen dioxide, sulfur dioxide, aldehydes, formaldehyde, acrolein, formic acid, odorants, particulates, soluble sulfates, and polynuclear aromatic hydrocarbons were determined. The concentration and mass emission rates of these compounds were measured in the laboratory under three engine speed and load conditions and with three exhaust control conditions, i.e., none, catalyst, water conditioner. Once calibrated, the engine was installed in the Bureau of Mines Safety Research Coal Mine and the concentration of exhaust pollutants measured at several distances downstream (inby) of the engine. Laboratory results confirm the relatively small effect of exhaust control devices on most pollutants under engine conditions of low speed and load. At higher engine speed and load, the catalyst is more effective in controlling many pollutants. The in-mine data indicates that during residence times, which are typical for miner/exhaust contact, most diesel exhaust pollutants do not decrease in concentration. The obvious exceptions are nitrogen dioxide, sulfur dioxide and formaldehyde. The concentration of these pollutants is reduced by up to 75 percent in five minutes. The lack of increase in levels of obvious reaction products indicates that surface loss may be a major sink for these pollutants.

Jan 1, 1980

By Finlay Campbell

Nickel laterite pressure acid leach plants and reduction roast plants have had a checkered history in their engineering, construction, startup and operational reliability. Many potential projects have been the subject of detailed studies over the last thirty to forty years but relatively few have advanced to commercial production. Four reduction roast plants are currently operating, an additional one was partially constructed but never completed, and another was started up in 1974 and shut down after 12 years operation. Three acid leach plants have been built and commissioned in the last five years, trying to follow the example of the Moa Nickel plant in Cuba. An additional acid leach plant project is currently on hold, following limited construction work, its future subject to review by the owner because of potential cost over-runs. This paper attempts to discuss difficulties that may be encountered as a project is developed and will address factors which may affect production ramp-up schedule, long term production performance and overall production success. Comparisons are made with ramp-up performance at other large metallurgical plants that employ some comparable unit operations. Keywords: Caron, PAL, nickel laterite ore, ramp-up, reliability, process development, equipment design, step-out, commissioning, startup.

Jan 1, 2004

By Jan Zwarcendyk

This study is primarily directed toward providing an understanding of the economic complexities associated with subsidence damage on the surface resulting from underground mining. Some of the pertinent theories on the physical stresses involved are reviewed, and both remedial measures and relevant laws in various countries are discussed. Part I (Chapters 1-3) is an historical overview of various aspects of subsidence problems (theoretical, remedial, and legal) during pre-World War I, between World Wars, and post-World War II, respectively. Part II (Chapters 4-9) presents a comprehensive analysis of the economic aspects of subsidence in relation to the following mining alternatives: (a) carrying out the lowest cost mining method without regard for any surface subsidence, (b) special mining techniques, (c) partial mining, (d) full recovery with stowing, and (e) sterilization or leaving the mineral unmined beneath selected areas. These alternatives are evaluated in terms of their measurable expenses.

Jan 1, 1971

By Juan Camus

To understand why some companies excel in creating value, Jim Collins (2001) and a group of postgraduate business students engaged in a comprehensive, five-year research project. They examined 1,435 U.S. companies for more than 40 years, seeking those that made significant improvements in their financial performance over time. The distinctive pattern sought was: ?Fifteen-year cumulative stock returns at or below the general stock market, punctuated by a transition point, then cumulative returns at least three times the market over the next 15 years. ?The search identified 11 outperforming companies, all in different industries, that were called the ?good to great? companies. To contrast these companies with similar peers within the same industry, the search also selected a group of comparison companies that failed to make the leap from good to great. Collins then set out to examine the transition point. What distinguishing features did the good-to-great companies have that their industry counterparts did not? At the heart of the findings about these outstanding companies is what Collins refers to as the ?hedgehog concept? ? how to find the one big thing that the company must focus on. According to Collins, those who built the good-to-great companies were, to one degree or another, hedgehogs. Those who led the comparison companies tended to be foxes, never gaining the clarifying advantage of a hedgehog concept, being instead scattered, diffused and inconsistent. This insight is complemented by Peter Drucker (2004), an influential management guru, who asserts that the first question an effective executive should ask is: ?what needs to be done?? Asking this question and taking it seriously, he asserts, is crucial for managerial success; and that the answer almost always has more than one urgent task, but the effective leader only concentrates on one task. In this last respect, Drucker emphasizes: ?If they [executives] are among the sizeable minority who work best with a change of pace in the working day, they pick two tasks. I have never encountered an executive who is effective while tackling more than two tasks at a time.?

Jan 1, 2011

By Carlton M. Ray, William P. Levy, Thomas Lindberg

"The District of Columbia Water and Sewer Authority (DC Water) is implementing its $2.6 billion DC Clean Rivers Project to reduce combined sewer overflows to the District’s receiving waterbodies and mitigate chronic sewer flooding in District neighborhoods. The First Street Tunnel project is a major component of the DC Clean Rivers Project, designed to mitigate sewer flooding and basement backups in the District’s historic and densely populated Bloomingdale neighborhood. Bloomingdale has been historically affected by sewer flooding and was severely impacted by four storms in the summer of 2012 that caused significant damage to homes, the environment and public property. As a result, DC Water accelerated the design and construction of the First Street Tunnel in order to mitigate the effect storms have on the undersized sewers serving the neighborhood. The infrastructure designed to mitigate flooding, including the tunnel, are located within the highly urbanized neighborhood – with some structures being less than ten feet from residents front door steps. The success of a large public works project of this magnitude and in this unique location depends on a well informed and supportive public. With the local community impacted by flooding but concerned about heavy construction impacts, this paper details the components of a successful public outreach plan and lessons learned throughout the design and construction process. Early identification of community mitigation, working cooperatively with stakeholders and frequent dissemination of accurate information required the project team to establish a culture of problem solving collaboration with the community. BACKGROUND Chronic Flooding in the Northeast Boundary Sewershed The Northeast Boundary sewershed, in which the Bloomingdale neighborhood is located, is served primarily by a combined sewer system and has a long history of chronic flooding problems during moderate to severe storm events. The sewer system that serves the Northeast Boundary drainage area was constructed by the Federal Government in the late 1800's when developed areas of the District terminated at what is now Florida Avenue. Since construction of the system, population within the sewershed area has grown at an exponential rate. In meeting the growing needs of the population, the District experienced development that transformed previously low-density rural areas into new communities. Impervious areas have increased drastically since the sewer system was constructed and consequently, the existing sewer system does not have the capacity to convey storms with return frequencies beyond the 2-year storm without flooding. As a result of the capacity limitations, many of the low-lying areas have become chronic flooding areas due to the surcharging of sewers."

Jan 1, 2016

This publication summarizes, for all interested parties, the research, development, and demonstration in-house projects programed by the Bureau of Mines for fiscal year 1981 (October 1, 1980 - September 30, 1981) under its Minerals Health and Safety Technology program. The objective of these projects is to provide an ordered and sequenced series of advances toward the Bureau's overall goal of providing the system technology required to create a healthier and safer working environment for the Nation's mining and minerals processing workers.

Jan 1, 1981

By I. Peerawattuk

Growing demand for Li-based battery technologies is leading to an unprecedented growth in the lithium industry. Although innovation in battery technologies has pushed lithium into the spotlight, lithium was not always known for its application in batteries. The primary use of lithium—prior to the introduction of commercial lithium-ion batteries in the early 2000s—was in the ceramics, glass, grease, and the medical industry. Before being converted into usable forms, lithium products must be upgraded from the raw material. Processes for recovering lithium may involve: thermal treatment, water leaching, solar evaporation, ion exchange, carbonation, and electrodialysis. Presented, is a historical review of lithium applications and the different techniques of converting lithium-rich minerals and brines into usable products with additional discussion on future lithium extraction processes.

By D. Tahija

"Carbonic acid prepared on-site from carbon dioxide gas is widely used in water treatment and increasingly in some industrial applications. It has not seen extensive use in mineral processing but is an attractive alternative to sulphuric acid for pH control, with the need to counteract high pH levels caused by cemented backfill of particular interest. The fundamental chemistry of carbonate solutions as applied to flotation and flocculation circuits is described as well as plant-scale application. A project to introduce use of carbon dioxide for pH control at the Hecla Greens Creek lead-zinc-silver-gold operation is planned to begin operation in the first half of 2015. INTRODUCTION Flotation pH Control and Backfill Most sulphide flotation circuits are run at pH values ranging from slightly acid to strongly basic, with slightly basic pH the most common. Lead sulphide circuits are typically run at values from 7.5 to 9, with zinc circuits running at higher values of 9.5 to 10.5. This has been the case with ores that produce a natural pH in the circumneutral range, so that the pH needs to be raised. Although lime [Ca(OH)2] is the cheapest reagent in use to raise pH, soda ash (Na2CO3) or caustic soda (NaOH) are also employed where sodium ions in solution are preferred to dissolved calcium, or, in the case of soda ash, the presence of carbonate is desired. The use of soda ash for pH control in lead circuits has been widely recommended for many decades (1). The situation is necessarily different at operations where cemented backfill is used in underground mines (2). Backfill, whether emplaced as rammed paste or pumped slurry, is composed of mill tailings mixed with around 10% Portland or similar cement. When later mining occurs near or adjacent to previously backfilled areas, a considerable amount of old backfill is inevitably mixed with new ore and shipped to the mill. Depending on orebody geometry, mining methods etc., the amount of backfill in mill feed can easily approach 20%, with periods of higher content not unheard of. The presence of so much backfill, with its high cement content, produces results largely indistinguishable from adding a large amount of lime to run-of-mine feed: mill pH in the grinding circuits can range above 11 and high concentrations of calcium ions are present. The need to raise pH disappears; the problem becomes to lower it."

Jan 1, 2015

By H. Herbert Hughes

Iceland spar is a variety of calcite ( calcium carbonate ) characterized by its purity , transparency , and perfection of crystalline structure . It takes its name from the country in which it was discovered . The actual demand for it is small , but the supplies of high - grade optical spar are so meager that the search for it has become international in its scope . Iceland spar is a scientific necessity , for without it research precision and technology would be hampered considerably . The earliest students of mineralogy were familiar with calcite , but the transparent variety was not discovered until early in the seventeenth century , when crystals of it were found in the bed of a stream in Iceland . It received little attention until 1669 , when Erasmus Bartholinus first recognized its powers of double refraction . The results of his investigation were published in a book , " Experimenta Crystalli Islandici , " which appeared in 1670. The law governing the action of the rerracted rays was discovered by Christian Huygens eight years later . The polarization of light rays in passing through Iceland spar was discovered in 1809 by Etienne Louis Malus , a French physicist , who published a paper describing the phenomenon . His work was closely followed by that of William Nicol , who in 1828 designed the Nicol prism which is still used as the source of polarized light in most optical instruments .

Jul 1, 1931

By J. Clark

Erosion control during the mining cycle can be more effectively planned using Erosion and Sedimentation Control Plans (ESCPs). This raises the issue of who should develop an Erosion and Sedimentation Control Plan Guidance document (ESCPG) to standardize the content of ESCPs. A search for ESCPG documents in Canada revealed no examples for mine sites. In the U.S. there are a number of regulatory authorities who developed such documents for mine sites, including EPA. An ESCPG is expected to result in: (a) plans will be more standardized (b) more clarity and efficiency for those generating ESCPs; (c) assisting regulators tasked with reviewing/approving ESCPs; (d) providing guidance for the mine effluent permitting process relative to sediment control; (e) providing a basis for developing and including ESCPs in the Environmental Assessment (EA) phase and the mine economic assessment; (f) applying and optimizing ESCPs above the ?watersheds? of sediment ponds; (g) utilizing the ESCPG document for ?exploration? sites; (h) lowering the risk of adversely impacting water quality downstream of mining activities; (i) providing a methodology for determining the need for sedimentation pond(s) during the construction and production phases; and (j) providing a clear environmental sustainability message relative to sediment control if the mining industry takes the lead in developing an ESCPG. ESCPs will proactively create increased administrative (regulatory) efficiency in the EA and sub-EA reviews relative to erosion control and sediment release from mine sites. This also assists the new initiative in BC, One Project, One Process (OPOP) and synchronous permitting (a variation of concurrent permitting): as an example, enhanced erosion control planning at the EA phase then allows the synchronous permitting initiative to proceed efficiently, particularly for the mine permit (Ministry of Energy, Mines and Natural Gas) and effluent permit (Ministry of Environment). Approximately twenty more management plans (e.g. ARD/ML, explosive management, emergency response, hazardous waste, sediment pond operation, environmental effects, environmental sampling, etc.) may also be entered into the EA process to create increased efficiency, and then feed into the synchronous permitting effort. The BC OPOP initiative also adds support to the Canadian Federal ?One Project, One Review Process? approach. The ESCP and a sediment pond management plan will also address the Canadian Metal Mining Effluent Regulations requirement for all discharges from mine sites to meet a grab sample of 30 mg/L Total Suspended Solids.

Aug 1, 2013

By M. Lindgren, M. Latva-Kokko

Process performance can be significantly influenced by proper design of hydrometallurgical reactors. Optimal reactor configuration is case specific and depends on process requirements such as reaction rate limiting factor and particle size distribution. Choice of materials and manufacturing methods also play important roles in highly corrosive and abrasive environment often involved in hydrometallurgical industry. In this paper performance of different reactor designs has been compared in some typical hydrometallurgical applications. Results show that significant improvement in energy consumption, gas utilization efficiency and equipment lifetime can be achieved with process specific reactor design.

Jan 1, 2014

By G Byrne

Long-term water management is typically ignored in mine closure planning. A review of 73 mine closure plans dating from 2007 to 2013 shows that, on average, relinquishment is proposed to be achieved in 11 years. A separate review of 57 mines in actual closure shows that only five have so far achieved relinquishment with an average closure period of 14 years after production cessation. The remaining 91 per cent of sites in closure have an average closure duration to date of 21 years - and still going.A common issue among those sites in closure is water management, with a further common issue being acid and metaliferous drainage (AMD). Of the closure plans that were reviewed only one site had allowance for long-term (>50 years) of water treatment. Of the sites in actual closure 25 per cent have reported that they expect such long-term water treatment, with many acknowledging that in perpetuity treatment is probable.Clearly there is a gap between what is being allowed in closure plans and the reality of closure. There are a number of factors leading to the optimism of the closure plans, including unrealistic assumptions, pressures to reduce closure cost provisions and the technical complexity of many AMD issues.Long-term water management is a reality that needs to be acknowledged and addressed. If addressed early in the mine life cycle the impacts for mining companies can be reduced.CITATION:Byrne, G, 2013. Long-term water management - the forgotten legacy of mine closure, in Proceedings Water in Mining 2013 , pp 163-168 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

Water is required as a key strategic resource in most mining and metallurgical processes and, in some countries, it has become a limiting supply for the development of mining activity. During the last years, mining industry efforts have been successfully focused on water use efficiency in the different processes. However, these efforts will not be sufficient to compensate for the growing demand of mining products and the decrease of ore grades. New efforts should be oriented to the search for alternative water supplies such as sea water, with or without desalinisation, or water harvesting. But to survive this growing pressure and to get a social licence to operate, the mining industry can also assume a proactive attitude and pursue a prominent role in water management at regional and local scale. This paper reviews some of these emerging issues, particularly in the context of the Chilean copper industry.

Jan 1, 2009

By D. W. Duncan, A. Bruynesteyn

Acidic mine waters containing solubilized uranium have been observed in many uranium and some copper mines. In every case, the sulphide and iron oxidizing bacterium, Thiobacillus ferrooxidans, was also present. This bacterium provides the ferric iron required to oxidize u+4, both by oxidizing available ferrous iron and by oxidizing pyrite or other available sulphide minerals. This latter oxidation also provides sulphuric acid and may increase extraction by exposing more uranium. The enhancement of bacterial activity and the results of some field tests are discussed.

Jan 1, 1971

By F. J. Palumbo

Effective recycling or disposal of flue dusts is a continuing problem for copper, brass, and bronze smelters. Over 300,000 short tons (st) of dust is generated annually by U.S. secondary copper, brass, and bronze smelters. The Bureau of Mines has developed an alkaline leach method for recovering metal values from copper converter flue dust containing zinc, tin, lead, and copper. The dust was leached with a hot solution of ammonium chloride and ammonium hydroxide to solubilize ZnO. All of the tin (as Sn02) and the metallic copper, lead, and zinc, as well as possible insoluble compounds of each, report to the residue. Dissolved copper and lead salts are removed from the leachate by cementation with granular zinc. Zinc oxide is precipitated by diluting the leachate with water. The tin-rich (9.8 pct) residue has a ready market. The cement product is recyclable to the smelting operation. The ZnO is at least 97 pct pure and has potential marketability.

Jan 1, 1985

By K. W. Major

"This chapter outlines the organization of mine/ mill complexes in Canadian mining companies. Many factors unique to the Canadian mining industry will affect the design of the organization in the future: geographic location, the size and the type of orebody, etc. Mining companies cannot choose where new operations will be located, that is dictated by the location of the orebody. New mines are seldom started near established communities. Rather, the towns usually grow up near the mines. The remoteness of most Canadian mining operations has caused severe problems in attracting and/ or retaining all levels of employees. This means that training has a high priority within each operation.Another factor affecting mine/ mill organizations is the size of the operation. Larger operations generally require more departments and increased specialization to manage equipment and manpower effectively. Thus, for mine/mill complexes, organizational charts are less standardized than in other industries. It is often necessary to organize around the work force rather than develop a chart and then acquire the trained personnel to fill the diagrammed positions.The information presented in this chapter has been derived from the responses received from a survey of Canadian mining operations.Principles of OrganizationOrganization can be defined as deployment of personnel to accomplish definite goals. In the mining industry, the major goals are typically the projected number of tons and grade of ore mined on a daily, weekly, monthly and yearly basis. Organizing involves establishment of authority relationships with provisions for both vertical and horizontal co-ordination within the company structure. Vertical co-ordination is the delegation of responsibility and communication of goals and reporting of progress between the supervisor and subordinate. Horizontal co-ordination is communication between departments at positions of equal authority to determine methods of achieving predefined goals. The organization structure must reflect the objectives and plans of the company, and must clearly define areas of authority.Two criteria for effective organization are departmentalization and manpower planning."

Jan 1, 1989

By T. J. Otto, C. H. Cloete, T. Mkhatshwa, T. J. van Heerden

The value realised by an open pit mine depends on the quality and integrity of the mine planning process as well as the level of execution against these mine plans. When managing the execution against the mine plan, how well the mine plan is executed spatially, is of critical importance. The short-term mine plan is the plan that is physically executed on most open pit mines. At the same time, the spatial mine-to-plan compliance is typically reconciled against the annual business plan. Short-term mine planning, therefore, plays an important role in the effectiveness of the spatial mine-to-plan compliance reconciliation process by providing operational teams with detailed designs and schedules, while ensuring that mining execution is spatially aligned with the business plan. The Sishen open pit iron ore mine (Sishen) strives to continuously improve spatial compliance to the business plan. Sishen enhanced the role that short-term mine planning plays in enabling the forward-looking component of the spatial mine-to-plan compliance reconciliation process. The enhanced short-term mine planning process focuses on detailed tactical sequence designs per mining pushback, the health of value chain buffers, spatial plan-to-plan reconciliation, and the associated management routines. This led to improved spatial mine-to-plan compliance to the business plan from 71% to 94% over the four-year period from 2020 to 2023 inclusive. These results indicate that the application of short-term mine planning as part of an integrated spatial mine-to-plan compliance process at open pit mines can contribute positively to improving the level of spatial execution against the business plan. This paper presents the enhancements made to the short-term mine planning process, which other open pit mining operations can consider to improve spatial mine-to-plan compliance.

May 27, 2025

By Gerald H. Luttrell, Seyed Hassan Amini, Aaron Noble

One of the most important processing engineering tools for designing mineral processing facilities is linear circuit analysis. This technique, originally conceived and developed by Meloy, Williams, and Fuerstenau nearly four decades ago, provides fundamental insights regarding how unit operations interact and respond when arranged in multi-stage processing circuits. Researchers have successfully utilized this tool to improve the operating performance of industrial processing circuits incorporating coal spirals, magnetic separators, mineral spirals, and eddy current separators. More recently, advanced versions of this tool have also been developed to provide a standardized framework for circuit mass balance calculations, to output exact analytical solutions to mass yield and value-based efficiency expressions, and to estimate uncertainty propagation in separation circuits. This article reviews the historical development of linear circuit analysis, describes how the technique has evolved to address more complex circuit design problems, and presents industrial case studies that highlight the importance of this process engineering tool.

By Juan J. Monsalve, AMAN SONI, ALEX PFREUNDSCHUH, Nino Ripepi

Ground control failures are one of the main causes of accidents in the underground stone mining industry. Some of the fundamental tools for rockfall hazard identification are related to rock mass characterization and geotechnical discontinuity mapping. Recent technological advances in these methods are related to remote sensing techniques and point cloud processing software for automated discontinuity mapping. Remote sensing techniques, such as LiDAR and photogrammetry, generate multimillion point clouds with millimetric precision, capturing the structure of the rock mass. The automated point cloud processing tools offer alternative algorithm-based methods to characterize and map these discontinuities. However, their applicability is constrained by multiple factors such as site specific conditions of the rock mass and the parameters used within the mapping algorithms. This paper evaluates the performance of automated discontinuity extraction software compared with manual virtual discontinuity mapping. Sampling windows from laser-scanned sections in an underground limestone mine are defined and mapped using discontinuity set extractor (DSE). Results from the virtual discontinuity software are compared with manually extracted fractures from I-Site based on reviewing orientation, trace length, spacing, number of extracted discontinuities, and processing time. The analysis determined that the automated mapping algorithm was able to identify the same discontinuity sets that had been manually mapped. The automated mapping software mapped an excessive amount of smaller fractures, which caused the comparison of both mapping techniques to be unsuccessful in terms of trace length and spacing.

Mar 19, 2021

By J. `. Spitzinger

In situ recovery (ISR) of uranium alters the baseline groundwater geochemistry in order to mobilize and complex uranium to extract and concentrate it. ISR wellfield restoration is often challenging, and primarily relies on groundwater sweep, reinjection of treated permeate, and/or injection of reductants. Greater focus should be placed on injection-based approaches (using existing infrastructure) based on established engineering concepts used for in situ remediation of groundwater plumes. Such injection-based approaches could shorten restoration timeframes consequently reducing long-term operational costs. This paper addresses various types of injection-based approaches to wellfield restoration based on in-situ remediation success with other constituents that require similar treatment. This paper describes necessary design practices for injecting reactive chemicals (e.g., reductants or biostimulants), operations and maintenance (O&M) strategies to prevent fouling of the chemical delivery system and well network, and natural constraints to restoration. Best practices for successful biostimulation strategies that minimize residual uranium, radium, oxoanions, and other trace elements are as described. Advantages of such injection-based approaches could include significant reductions in restoration times, and consequently, lower restoration costs.

Feb 23, 2014