Search Documents

By G. Krogman, C. Walla, B. Wood

The Gebo Mining District (District) is located in the Bighorn Basin of Wyoming. Commercial underground coal mining began in 1906 with the arrival of the railroad in Thermopolis, which is located approximately 11 miles to the south. Mining in the District ceased by the early 1970’s. In Fall of 1999, Lidstone and Associates, Inc. (LA) and their subcontractors were retained by the Wyoming Abandoned Mine Land Division (WyAML) to perform an inventory of over 500 abandoned mine sites across Wyoming. During the summer of 2000 field inventory, a 30-foot deep headcut (Figure 1) and sink-hole were noted in the West Fork of Sand Draw (WFSD), immediately west of the Town of Gebo. The headcut and sink-hole were located at the culvert outfall associated with a stream crossing of a relatively well traveled county road. Upon further investigation, it appeared that underground mine workings had been exposed at this location. This resulted in a condition whereby water would be conveyed directly into the mine workings during a runoff event. The exposed mine workings as well as stream capture created a very hazardous condition. The WyAML implemented mitigation measures in the summer of 2000 by constructing a temporary stream crossing upstream of the existing failed crossing. To address this hazardous situation as well as a number of other hazards identified in the District during the field inventory, the WyAML retained PHC Reclamation, Inc. (PHC). PHC was directed to perform a field investigation and develop a Reclamation Plan to address all existing abandoned mine hazards in the District. Federal, state, and private parties own lands within the District. Hazards identified during the investigation included an underground mine fire, open adits, open shafts, subsidence, drainage problems, and coal slack. A Report of Investigation (ROI) was submitted to various regulatory agencies that documented the existing conditions and conceptual reclamation plans to remediate the hazardous conditions. After review of the ROI by the US Department of Interior - Bureau of Land Management (BLM) an on-site meeting was conducted. BLM Cultural Resource personnel declined to approve a District reclamation project until a historical overview of the entire District was prepared. Due to the hazardous situation associated with the WFSD stream crossing, Hot Springs County Road and Bridge Department convinced various state and federal regulatory agencies to allow reclamation of the stream crossing to occur. A decision was made to allow reclamation on privately owned lands within the WFSD drainage. This decision limited the amount of channel that could be subjected to reclamation upstream of the crossing to privately owned lands. PHC contracted LA to perform a geologic, geomorphic, hydrologic, and hydraulic investigation of the drainage to assist in the development of a WFSD reclamation plan. LA’s investigation consisted of four parts: Delineate the extent of mine workings in the area; Identify all drainage structures that required mitigation; Survey a series of channel cross-sections and a longitudinal profile of the impacted channel; and, Develop basin hydrology to assist in the design of a stable reclaimed stream channel.

Jan 1, 2006

By H. Chu

Selective Agglomeration experiments carried out to clean ultra-fine coal are examined. Effect of feed size, pulp density, coalescing agent dosage, and mixing intensity and duration on the kinetics of agglomeration are principally evaluated. A computer coded population balance model governing agglomerate size distribution and composition utilizing coalescence and breakage mechanisms is developed. Model calibration, verification and extension are analyzed.

Jan 1, 1987

Advanced Jig Separation of Shredded Plastics The authors have reported that the RETAC jig is very useful in separating relatively low density particles such as plastics, and demonstrated that highly efficient jig separation of plastic components in discarded office machines is possible in pilot-scale tests. To further improve the separation efficiency, a hybrid jig (RETAC jig with air bubbler under the particle bed) which can separate plastics having similar specific gravities using differences in wettability produced by a pretreatment, and a reverse jig (modified RETAC jig for plastics lighter than water) were developed. This paper reviews the separation of shredded plastics using advanced jig separation technology (RETAC, hybrid and reverse jigs). Wettability control of the plastics for the advanced jig separation is also reported.

Sep 13, 2010

By S. Surapunt, C. M. Nyamai, K. Itagaki

"The use of liquid copper as a medium for zinc extraction has been used in the Warner Process as a method of processing zinc-lead sulphide ore. The recovery of zinc metal is based on the reaction:ZnS(s) + 2Cu(l) = Zn(g) + Cu2S(l)In this method, thermodynamic and phase equilibria investigations of the Cu2S-FeS-ZnS and Cu2S-PbS-ZnS systems are of importance and form the basis for the liquid sulphide phase which appears as a product and is used as a solvent in the Warner Process. Phase relations in the Cu2S-FeS-ZnS and Cu2S-PbS-ZnS ternary systems were determined experimentally at 1473°K to provide a fundamental basis for the new zinc smelting process. The results show that the solid solubility of ZnS in the two systems is very small (2 wt% to 3 wt% ZnS in FeS, 4 wt% ZnS in Cu2S for the Cu2S-FeS-ZnS system; less than 0.5 wt% ZnS in both PbS and Cu2S for the Cu2S-PbS-ZnS system). The Raoultian Activity Coefficient of ZnS in the liquid mixtures and the vapour pressure of zinc over the matte in both systems is relatively large (?° = 7.7 – 15.8, Pzn(atm) = 0.088 – 1.026 for the Cu2S-FeS-ZnS system; ?° = 8.9 – 12.9, PZn(atm) = 0.075 – 0.214 for the Cu2S-PbS-ZnS system). On the FeS-ZnS join, the only phases detected are FeS and iron-rich sphalerite (Zn, Fe)S. The binary join mixture occurs at about 92 wt% FeS-8 wt% ZnS at 1473°K. Electron microprobe examination of the quenched samples indicate about 47 wt% to 48 wt% FeS in sphalerite and about 2 wt% to 3 wt% ZnS in the iron sulphide phase. On the Cu2S-ZnS join, microprobe analysis reveals that the maximum solubility is 4 wt% Zn in liquid Cu2S and 3.6 wt% Cu in solid ZnS. In the Cu2S-PbS-ZnS ternary system, microprobe analysis of the quenched samples indicate on average, 5 wt% ZnS in the liquid phase region. The only phases detected on the PbS- ZnS join are ZnS and PbS. The eutectic phase contains, on average, 13 wt% ZnS. The phase relationships, very low solid solubilities of zinc sulphide in the liquid mixtures of both Cu2S-FeS-ZnS and Cu2S-PbS-ZnS systems, coupled with the high Raoultian Activity Coefficient of ZnS as well as the high vapour pressure of zinc over matte all favour the partitioning of zinc metal into the vapour phase. This new process is cost effective and bypassesthe expensive and tedious conventionaltechnique of zinc production involving oxidationof the sulphide ore by roasting followed bya reduction process to extract the zinc. Theresults indicate that a new zinc smelting technologyusing the Warner Process would bemore efficient and preferable over the traditionalmethods of zinc extraction."

Jan 1, 2002

By F. D. Everett

Thermoelectric and metal alloying applications have changed the status of tellurium from oversupply to under supply . In a search for new sources of this element in Arizona , Colorado , New Mexico , Utah , and neighboring states , the Bureau of Mines analyzed more than 200 samples and obtained the results of tellurium determinations by private companies on more than 500 samples from a wide variety of mineral - bearing deposits . The About 40 minerals containing tellurium have been reported , mainly tellu- rides of gold , silver , bismuth , mercury , lead , copper , iron , and nickel . minerals usually occur in small quantities and identification in ores is extremely difficult . Samples containing more than 0.1 percent tellurium were taken from the Hilltop and Memphis properties in Dona Ana County , N. Mex . , and the Silver King property in White Pine County , Nev . , where development was chiefly for base metals . The Lone Pine mine in Catron County , N. Mex . , and the Bambolla mine near Moctezuma , Sonora , Mexico are potential sources of native tellurium occurring in small but high- grade pods . Much of the production of tellurium has come as a byproduct of electro- lytic refining of copper and lead- zinc ores in Arizona , Colorado , New Mexico , and Utah . Base -metal ore deposits will continue to be the most important pri- mary source of tellurium , although the concentration in ores is nearly always less than 10 parts per million . Any significant increase in output of tellu- rium probably will be related to production and improved efficiency in smelt- ing and refining base - metal ores .

Jan 1, 1964

Electrochemistry Measurement, Using Chena Analyser, to Investigate Selective Separation of Pentlandite and Pyrrhotite

Sep 13, 2010

By Charles L. Allie

In June, 1980, Reserve Mining Company completed a 370 million dollar construction project which included process modifications required to reduce the silica content from nine to five percent by weight and increase the iron con- tent of Reserve's pellets from 62.5 to 65.8 percent by weight (dry basis); process modifications and additions required to implement "best available technology" water quality controls; and installation of "best available technology" air emission controls. The new process began operation on June 24, 1980 and is being optimized to meet design objectives. Dry cobbing, fine screening and flotation additions to the concentrating process have reduced the silica content of Reserve's pellet from nine percent to five percent by weight. The process reclaims and reuses all process waters, stores all tailings in a zero discharge tailings basin and meets all air emission standards.

Jan 1, 1980

By W. G. Sandell, G. M. Potter

"As a part of the wartime activities of the Bureau of Mines, metallurgical services were extended to other Government agencies engaged in purchasing and stock-piling some of the more critical and strategic materirals. At the request of George A. Easley, representative of the MetalsReserve Company, beneficiation studies were made on a sample of complex tin-tungsten ore from the Urania mine in Bolivia, South America.The low-grade Urania ore (1.9 percent Sn and 1.55 percent W03) contained a very complex of cassiterite and scheelite with iron sulfidesand quartz. The problem involved in concentrating this ore was the removal of sulfides and silica by stage flotation and gravity concentration for the production of a marketable tin-tungsten concentrate. The sulfides and primary quartzite were readily rejected, but the secondary quartz was intimately associated with cassiterite, and ultimate recovery depended on treatment of minus 560-mesh (theoretical) sizes.The ore was amenable to concentration by ore dressing. Seventy percent of the tin and 83 percent of the tungsten were recovered in a product that assayed approximately 20 percent Sn and 20 percent W03 and that met grade ""F"" specifications of the Metals Reserve Company for mixed tin-tungston concentrates."

Feb 1, 1948

By E. Thune, F. Stålesen, E. O. Stensholt, O. M. Dotterud, E. E. Henriksen, P. O. Ramsdal

"The development and commercial operation of the Falconbridge chlorine leach process have been described in papers in 1985 and 1987. Since this time, various process improvements have been implemented and the capacity of the Kristiansand refinery has been increased to 85 000 t/y Ni, 40 0000 t/y Cu and 4500 t/y Co. The focus has been on continuous improvements in productivity, the use of energy and other costs. Several environmental issues have also been eliminated or reduced since 1987. IntroductionThe first nickel refining operation in Kristiansand, Norway, started in 1910 based upon raw materials from Norwegian mines. In 1929, Falconbridge Nickel mines purchased the refinery to acquire information and the patent rights to the Hybinette refining process that was practised at the small Kristiansand refinery. Falconbridge ownership has now, for more than 70 years, provided a strong base regarding raw material supply, financial resources and technical support for further expansions and major technical improvements at the refinery.The main concepts of the new chlorine leach process were developed in the laboratories from 1966 to 1969 and the process was piloted from 1970 to 1972. The main stages in the commercial plant were started in the 1975 to 1981 period. After 1981, there have been a number of process modifications, plant expansions and improvements to operating practices. The developments up to 1988 have been described in previous publications (Stensholt et al., 1986, 1988).This paper presents an overview of the process and how it is practised at Falconbridge Nikkelverk AS (FNA) today and describes some of the main changes that have been implemented since 1988. During this time, the nickel capacity has been expanded from 54 000 t/y to 85 000 t/y and the cobalt capacity from 2000 t/y to 4500 t/y. The paper describes how these expansions were achieved together with continuous improvements in operating efficiency and also gives an overview of the main environmental concerns at the refinery."

Jan 1, 2001

By W. Armstrong Price

INVESTIGATION by German chemists during the World War showed that particles of iron oxide form rapidly in iron pipes carrying hydrogen gas under pressure when the gas contains small amounts of water. Under these conditions, the gas frequently exploded when expanding into a dirigible. The explanation of the explosions lies in the building up of a charge of static electricity in the flow just beyond the orifice and the ignition of the gas by a spark accompanying discharge of the electricity. Friction between the moving particles and the pipe generated the electric charge, which was manifested by a pale blue glow formed in the flow at pressures above two atmospheres. In one experiment, this glow, at eighty atmospheres, extended for a distance of forty to fifty centimetres, but did not ignite hydrogen and air mixtures until the charge was col-lected by a conductor and discharged across a gap between electrodes placed at the side of the column of gas. Autoignition did not occur when this discharge was effected at a distance from the gas column, nor if the gas used was thoroughly dried and free from impurities. The electric charge has been studied by placing various wire and screen conductors in the outcoming stream of gas, Guest having summarized these experiments. The application of these conclusions to fires in petroleum and natural gas issuing uncontrolled from wells is made in the following paper, citing the ignition of a wild gas well in Texas.

Jan 1, 1936

By María Quintana, Roger Veramendi, Gerald Salazar, Clemente Luyo, Noe Cabanillas

En este trabajo se presenta un sistema autónomo para remoción de plomo de efluentes mineros con monitoreo remoto, cuyo sistema opera a base de un novedoso material adsorbente, que se presenta en este estudio. Este material, obtenido a partir de arena y grafito, es estable, escalable, reproducible, biodegradable y se puede usar para el tratamiento de metales pesados en agua por medio de una red de filtros en boyas. El equipo desarrollado ha logrado remover casi el 99% a niveles de 10 ppm de contaminación de plomo en un rango amplio de niveles de pH, lo cual garantiza su correcto funcionamiento bajo condiciones de campo. Los componentes del sistema se basan en partes recicladas de otros equipos y utilizan energía solar para su funcionamiento continuo. Asimismo, el equipo contará con un sistema de monitoreo a control remoto, para que el usuario pueda registrar los niveles de plomo a la salida de la red de filtros.

Sep 20, 2019

By J. P. Smith

Permian salt measures carry extensive lenses of soluble potash salts in north central Germany. Potash deposits of Oligocene age are found in the Upper Rhine Graben of Alsace (France), and in the Catalonian Basin of Spain. These deposits are found in a wide range of structural settings. Reserves are large, and the production of potash salts is an important phase in the economy of each of these countries.

Jan 1, 1950

By Virgil W. Carmichael

In the Fort Union formation of western North Dakota, eastern Montana and northeastern Wyoming there are immense tonnages of lignite and subbituminous coal that have not yet been evaluated in terms of present economic conditions. Continued expansion of United States energy requirements has focused ever increasing attention on this tremendous resource, particularly as efficiency in mining and transporting of coal, as well as in electrical energy generation and transmission have improved and as hydrogenation and gasification of coal approach economic feasibility. This "total energy" concept for coal includes all of the energy uses that coal offers and has resulted in mergers of oil and coal companies and acquisition of coal re- serves by oil companies, as well as by coal companies and others. There is no doubt that these coals are entering an exciting new era of exploration and development that will result in greatly increased production. As a matter of fact, increased consumption for energy generation is well under way and recognition of the economic feasibility of high-Btu pipeline gas and synthetic petroleum products from coal is imminent. As coal is gradually displaced in steam electric generation by the more exotic fuels and processes, it will be increasingly used as raw material for the synthetic petro-chemical industry and the organic chemical industry.

Jan 1, 1968

By C. J. Bise

In August, 1977, the Federal Surface Mining Control and Reclamation Act was signed into law [I]. It stated that: "The Congress finds and declares that because of the diversity in terrain ... and other physical conditions in areas subject to min ing operations, the primary governmental res- ponsibility for developing, authorizing, issuing, and enforcing regulations for-surface mining and reclamation operations subject to the Act should rest with the States." Section 516 of Title V (Control of the Environ mental Impacts of Surface Coal Mining) of the Act deals with the surface effects of underground coal mining operations. "Each permit issued under any approved State or Federal program pursuant to this Act and relating to underground coal mining shall re quire tfieoperator to adopt izeasures consist ent with known technology in order to prevent subsidence, causing material damage, to the extent technologically and economically feasible, maximize mine stability, and main tain the value and reasonable foreseeable use of such surface lands, except in those instances vhere the mining technology used requires planned subsidence in a predictable and controlled manner: Provided, that nothing in this subsection shall be construed to prohibit the standard method of room and pillar mining. "

Jan 1, 1980

The revival of the mining industry at Captain's Flat after a long period of years of inactivity has attracted attention to the importance of the ore-deposits of that field as potential sources of supply of lead and zinc. Mindful of the necessity for taking stock of the State's mineral resources, the Department of Mines of New South Wales as part of its programme of geological investigation, carried out a survey of the oredeposits and associated country rocks during 1938 and 1940.Surface geology was mapped in detail and all available exposures were examined and logged. Unfortunately, and this condition militates against the formulation of conclusions because of insufficiem.t data, some of the older workings, notably in Keating's Section, were inaccessible and the logging of levels and stopes is by no means as complete as could be desired. However, with the progress of development and exploration, further information of geological value will come to hand for incorporation in supplementary reports. It may be expected that, under such circumstances, modification of certain statements herein expressed may be necessary but it is not anticipated that any vital alteration will be occasioned.Within the State of, New South Wales, Captain's Flat ranks second to Broken Hill as a pqtem.tial producer of lead and zinc. In addition, large quantities of iron pyrites are available for the manufacture of sulphuric acid which finds application in the superphosphate industry.The mines are now controlled by an operating company known as Lake George Mines, Ltd., incorporated in New South Wales, the parent organisation being the Lake George Mining Gorporation Ltd., registered in London.Over £600,000 has been spent by the Company in exploration, mine development, surface plant, housing and water 'conservation, while the State' Government constructed a branch railway from Bungendore at a cost of £200,000. The various activities consequent upon these development and construction programmes and the prospect of employment in the industry has led to a rapid increase in the population of the township.The State, generally, has benefited to the extent of a substantial contribution to the relief of the unemployment problem, and it is hoped that reasonable permanency will be assured to some hundreds of workers for many years.

Jan 1, 1941

By C. Samuelsson, H. Ahmed, B Björkman, A. Andersson

The cost of raw material and energy is a continuing driving force towards working with increasing the recycling of ore based steelmaking residues. In Sweden no on-site sinter plants are operated at the integrated steelworks. Instead, selected residues from the plant are incorporated in a cold bonded briquette product which is recycled to the process via the blast furnace (BF). Since the BF sludge is the major bleed of zinc out of the furnace it is required to be de-zinced prior to recycling in the briquette product. In the present work landfilled BF sludge has been characterized with respect to chemical composition, particle size distribution, X-ray diffraction (XRD), and scanning electron microscopy (SEM). The sludge was also subjected to laboratory scale hydrocyclone trials aiming at reducing the zinc content making the sludge viable for recycling. The results suggested that the sludge had been agglomerated prior to the characterization and hydrocyclone treatment. The zinc removal using the hydrocyclone was discussed.

Jan 1, 2015

By T. McWaters

Miami Copper Company began a block-caving operation in 1911 using a gravity mill to separate copper minerals from the Pinal Schist host rock. The tailing was deposited by the upstream method using perimeter launders and spigot valves in six canyons adjacent to the mill until 1932. In 1928 the larger and more distant Solitude tailing pile was developed which by 1932 was receiving all tailing except for upsets. In 1925 Miami Copper converted its gravity mill to flotation which began to produce higher sulfide copper recoveries.

Jan 1, 1990

By Olav Moklebust

The R-N Process is an outgrowth of the development by the National Lead Company's Norwegian subsidiary Titania A/S, of a process for producing metallic iron and a high titanium content co-product from ilmenite. Development of the process for the treatment of iron ores was continued as a joint project of the Republic Steel Corporation and the National Lead Company in 1953. More recently in July, 1957, the R-N Corporation was created by these two companies to undertake the commercial promotion of the results of this joint project. This paper has been prepared with the permission and encouragement of these three companies. The R-N process has as its objective the making of metallic iron from iron ores or iron ore concentrates. The general principles of the process have already been disclosed in technical papers and patents. In general the process comprises the following steps: 1. Iron oxide in crushed natural iron ores or iron ore concentrates is reduced to about 95% metallic iron, without fusion in a rotary kiln in the presence of solid carbonaceous fuel,*such as, coke or char, limestone and combustible gases. 2. The kiln discharge, consisting of metallized ore, coke, lime and coke ashes, is cooled. The excess coke is regenerated and recycled to the kiln feed.

Jan 1, 1959

By R. Casagrande, L. R. Moore, J. Sessoms, P. Macy

"A South American nickel mine has been producing a nickel concentrate that also contains copper and iron (15 percent nickel, 5 percent copper, 28 percent iron) for the end use of stainless steel production. A critical specification for the quality of the steel is the iron to magnesium oxide ratio (Fe:MgO), with a ratio of below 3.5:1 having a substantial impact on the nickel value. This nickel concentrate producer historically mined the sulfur-rich mineral pyroxenite but had been forced to move to a magnesium oxide/silicate (MgO/SiO4)-rich mineral harzburgite, resulting in nickel recovery being reduced to around 50 percent to maintain the required Fe:MgO ratio. In this study, ore mineralogy, water chemistry and the chemistries associated with the flotation process were evaluated in an effort to increase nickel recovery while maintaining the Fe:MgO ratio according to specification. New chemistry was introduced with the specific goal of complexing with the MgO and retarding its interaction with the bubble flow in the flotation process.IntroductionGlobal nickel production in 2011 totalled to 1,770,000 tons, according to the Raw Materials Group (2013). From 1950 to 2005 there was an aggregate 4.4 percent increase in nickel production, with a market-value high of $1,000/ton nickel reached in 1998 (Mudd, 2010). Approximately 65 percent of nickel production is consumed by the stainless steel industry, with 12 percent of the remainder used in super alloys or nonferrous alloys. Nickel imparts corrosion resistance, temperature resistance and other benefits to its alloys (Table 1) (Oberg, 1996; Cáceres, 2003). The dominant types of nickel-bearing ores are classified as either laterites (limonite: nickel-iron oxide; and garnierite: nickel hydrosilicate) or magmatic sulfide deposits (pentlandite: iron-nickel sulfide) (U.S. Geological Survey, 2013a, 2013b). In 2012, about 40 percent of the nickel ore mined was sulfidic-type ores and about 60 percent was laterite. The processing of laterite ore is expected to continue to increase as the availability of sulfidic ores continues to decline."

Jan 1, 2015

By J. Marks

The measurement of greenhouse gas (GHG) emissions from primary aluminium production and inventory of these emissions of carbon dioxide and PF Cs have become an important issue for primary aluminium producers. Most global producers have either voluntary emission goals or emissions limits established through national regulatory requirements. International good practices for inventory of these emissions for national governments are established through the Intergovernmental Panel on Climate Change (IPCC). The current good practices, last updated in 2000, are being revised and are expected to be adopted by governments in the spring of 2006. There are a number of changes expected in the guidance that will impact how facilities account for their GHG emissions. This paper describes the changes to the guidance and the implications of these changes for aluminium producers.

Jan 1, 2006