Search Documents

By C. Guo, R. J. Chalaturnyk, M. MacKinnon, J. D. Scott

The Mildred Lake Settling Basin (MLSB) is the largest disposal site for mature fine tailings (MFT) at the Syncrude Canada Ltd. oil sands plant. Over the past years (since 1996), there has been a marked change in the densification behaviour of MFT in the MLSB. Methane-producing microorganisms, known as methanogens, have become very active, and large amounts of biogas (mainly methane) have been produced. Continued field monitoring of the MLSB has provided convincing evidence of the rapid densification process (rapid water drainage from the tailings) at the area with intense microbial activity. This rapid densification has caused pumping challenges in the transfer of fine tailings from the Mildred Lake Settling Basin for the creation of composite tailings. It may also have potential positive effects in accelerating the reclamation of the oil sands fine tailings. A field and laboratory research program was carried out to study the mechanism leading to the rapid densification phenomenon. A review and discussion of the research program is given and some results from the field investigations and small-scale column tests are presented in this paper.

Jan 1, 2007

By Guo Wenbing

"INTRODUCTIONThere is a great amount of coal (about 140 billions tons) left unmined under the surface structures, water bodies, railways (referred to as the “three-body”). Coal mining under “threebody” especially that under surface structures has become a major problem in the mining area. The key problem of mining under surface structures is to control overburden strata and surface movements. At present, the major surface subsidence control methods are strip pillar mining, backfilling mining method, room and pillar mining, grouting of bed separations, harmonic mining, and so on. Wongawilli mining method is a high-efficient shortwall mining method developed based on the room and pillar mining, and named after the first successful trial in Australia “Wongawilli” coal seam. The room and pillar mining equipment such as continuous miner is employed in this method. Its major advantage is flexible face layout. It can be used to mine the small wedge coal blocks and those that are difficult to be mined with retreat longwall mining method. It requires less capital investment, short lead time for production, flexible equipment operation and face move and high productivity. It has been applied in some China’s coal mines.The “Wongawilli strip coal mining technology” is a new coal mining method for mining under surface structures. It combines the strip mining longwall layout and Wongawilli high efficient mining technology. This technology can fully utilize the advantages of both the strip pillar and Wongawilli mining methods, and overcomes the disadvantages such as frequent face move, and low mining efficiency in strip pillar mining, and poor ventilation condition and poor long-term stability problems of coal pillars. In this paper, the Wongawilli strip mining method was designed for Wangtaipu mine and its feasibility was studied using numerical modeling and surface subsidence prediction.Geological and mining conditionsAt present, most of the No.15 coal seam reserves totaling 377.07 million tons in Wangtaipu mine are located under surface structures. In order to mine the coal under the surface structures, the Wongawilli strip mining method was employed. An appropriate panel was selected for trial and the surface movement monitoring lines were set up. The trial area is located in panel XV2214 (East) ( re 1). In this area, the floor elevation of coal seam is +634~646m, the surface elevation is +810~817.5m, and the average depth of coal seam is about 174m.The average panel length is 282m and average panel width is 73.5m. The seam dips 1~3° and is 1.8~2.5m thick with an average of 2.15m. The roof and floor rock characteristics are shown in Table 1."

Jan 1, 2015

MR. J. F. MYERS, Consulting J3eneficiation Engineer, Greenwich, Conn.: In the written discussion contributed by Mr. F. C. Bond in item ( 2) (page 515), speaiking about the significance of the ratio of mill diameter to the make-up ball diameter, he states: "When this ratio exceeds 100 the power and capacity of the mill are de-creased"; and the paragraph ends with a reference to the 30 per cent ball volume "with some de-crease in mill capacity". I believe this broad statement is incorrect. When we are dealing with a non-cataracting mill, pre-ceded by a good rod mill, there is a slight increase in capacity, but the power does drop. The second point that I consider needs consideration is Mr. Bond's item (8), Proper Mill Speed (page 516). This paragraph should be qualified to cover single-stage mills only. It does not apply where a rod mill is followed by a non-cataracting ball mill. The statement as is, with no qualification, gives an erroneous idea of proper mill speeds.

Jan 1, 1957

By W. D. Keller

Scanning electron microscopy (SEM) accompanied by X-ray energy dispersive analysis (XES) is a useful tool in process clay mineralogy. The texture of kaolin, illustrated by SEM, gives a clue to its mode of genesis and probable industrial application. One type of kaolin, originating dominantly by weathering, has an open texture, slakes readily, and is used for filling and coating paper. Another type, in contrast, originates by diagenesis of Al-silicate sediments, and spectacularly resists slaking, thereby enabling it to maintain its bulk density and controlled size and shape of particles after crushing and moistening; this meets an important requirement for the manufacture of refractories. Ratios of elemental Al:Si that may be rapidly determined by SEM and XES yield information on the origin and purity of bauxite and bauxitic clays, and aid in quality control and processing of them. SEM of dissimilar textures of quartz, as in chert and novaculite, are evidence for geothermometry on a stratigraphic scale that is potentially useful in delimiting thermally favorable or unfavorable areas for hydrocarbon exploration, and possibly for unexposed metallic ore deposits.

Jan 1, 1982

By James K. Gowans

The Red Dog Operation is located in northwestern Alaska at Latitude 68°, 100 miles north of the Arctic Circle and 50 miles inland from the Chukchi Sea. The orebody was acquired by the NANA Regional Corporation, (an Alaska Native Corporation established by the Alaska Native Claims Settlement Act of 1971), in 1980 in their land selection. In 1982 Cominco American and the NANA Corporation signed a development agreement and Cominco Alaska Inc., a wholly owned subsidiary of Cominco American, was formed to manage the Red Dog Project. An extensive exploration program in 1980 -1982 outlined a mineral inventory of 85 million tons, at a grade of 5.2% Pb, 17.1 % Zn, and 2.4 oz/ton Ag, which makes the Red Dog the second largest deposit ever discovered. Broken Hill, in Australia, is the only zinc orebody which was originally larger than Red Dog. The design of the facilities is to process 2.1 million tons of ore annually, which will produce 560,000 tons of zinc concentrate, 100,000 tons of lead concentrate and 50,000 tons of bulk lead/zinc concentrate.

Jan 1, 1991

By Etienne A. Ritter

INTRODUCTION. THE Evergreen mine, located at Apex, in the northern part of Gilpin county, Colorado, has opened a very peculiar and interesting copper-deposit, in which both bornite and chalcopyrite occur as rock-minerals. The country-rocks are crystalline schists cut by dikes of granulite and of pegmatite. At the Evergreen property they have been cut by a dike of a new kind of eruptive rock, to which I have given the name " Evergreenite" The rock is composed of quartz, alkali feldspars, orthoclase and albite (often interlocked as microperthite), with augite of the aegirine variety and long needles of enstatite and diallage. For reasons stated below, I believe the dike to be of Tertiary age. It is- easily traced on the surface of the ground, from a point in the bottom of Pine creek, about a mile below Apex,. to the top of Nevada hill, 1,500 ft. beyond and 600 ft. above it. (See Fig. 1.) It varies from 3 to 12 ft in width, and is bounded on both sides by contact-zones about 60 ft. wide, in which the crystalline schists have been changed into pseudo-quartzites or pseudo-gneisses, according to the injection of an excess of quartz or of feldspars through the special layer of the schists.. The most interesting feature is the presence of the pyroxenes, which are always found, though in very variable proportions from place to place, in the layers of these' metamorphosed crystalline schists. The dike has torn from its walls a large number of fragments of the wall-rock. It must have been in a viscous state when that happened, because these fragments of the wall-rock do not show any sign of resorption or of assimilation by the magma. In places they are so distinct and so numerous that the rock looks to the naked eye like a pseudo-breccia, of which, never-

Jan 1, 1908

By Mikiya Tanaka, Mikio Kobayashi, Kazuya Koyama, Yoshihiro Nishisu

Preparation of multicomponent powders are very useful and important for producing the materials with complicated and homogeneous structure. Therefore multicomponent powders have a lot of attention in the field of advanced value-added materials. The aqueous processing in hydrometallurgy has a broad potential for producing multicomponent homogeneous precipitates. Furthermore the aqueous processing has a future potential for integrating the separation, precipitation and synthesis processes. In this presentation the precipitation from homogeneous solution including rare-earths and/or common metals is presented. These precipitates probably consist of almost monodispersed, multicomponent and spherical particles by precisely controlling several reaction factors, reaction temperature, concentrations of starting materials, pH and so on. The separation of the nucleation stage and the growth stage of the particles is very important and how to control the reaction factors to realize enough separation is discussed. In this presentation the systems of Y-Eu-0, Y-Fe-0 and Y-Al-0 are mainly presented. In addition the precipitation-stripping method from organic phase is presented focusing the synthesis of multicomponent powders of Ni-La-0 system. These precipitates have multicomponents homogeneously and so they are converted to multicomponent ceramic powders by calcination. They are important compounds as phosphor, opto-magnetic materials, optical materials, hydrogen storage alloy or as the related precursors. In this presentation some characterization of these particulate materials is included.

Jan 1, 1998

By G. Adderley, Rob. Farnfield, L. Bermingham

The benefits of using electronic detonators within the drilling and blasting process in both surface and underground mining operations are well established and the use of this technology is widespread in the minerals industry. However, many users of such devices will also have experienced misfires where an electronic detonator has malfunctioned and shows evidence of damage from either transient shock or gas pressure. This is typically exhibited as a detonator shell that has collapsed causing damage to the internal electronic components before the detonator has initiated. Users often describe such detonators as being “shrink-wrapped”. The excavation of a misfire is always a hazardous operation, and it is better to minimize the risk of one happening in the first place. As part of a programme to improve understanding of this phenomenon and to allow a comparison between differing designs of detonators, a simple practical test was developed. This process involves the firing of a booster near electronic detonators in water. This paper describes this test work and draws some tentative conclusions on pressures for onset of damage with detonator shells made from different materials. The investigation has also yielded data showing that for some designs there is little difference between the pressure resulting in complete malfunction and sympathetic detonation

Jan 1, 2024

By Vernon C. Allison

The explosibility of coal dust has long been recognized by competent investigators as constituting one of the dangers of mining coal and in the use of pulverized coal as a fuel in industrial plants. The Bureau of Mines has carried on extensive series of experiments dealing with this subject, and has not only developed methods for the practical prevention of this danger, but in the, course of these experiments has developed a standard method of determining the relative explosibility of coal dusts and other organic dusts.3 Oil shale contains compounds 'of carbon and hydrogen that are either of a petroleum nature and are strongly ,adsorbed upon the incombustible part of the shale, or else are present in the shale as a compound ("kerogen") which has the property of changing into petroleum-like products when acted upon by heat. The oil shales may contain varying amounts of the organic matter, ranging from a trace to more than 66 per cent, depending upon their richness; therefore, it is important to know whether the dusts formed in mining and handling these oil shales are explosive when mixed with air and if so, to indicate remedial measures. This paper gives the results of explosibility tests of several pulverized oil shale's, selected as being typical of those which in the future may be used in commercial shale-oil production test on a sample of typical Colorado oil shale has been., published in an earlier paper.4

Jan 1, 1926

By Jens Decker

"In consideration of energy savings the ideal refractory furnace lining should possess the following features:??Lowest thermal conductivity possible in order to avoid heat loss.??Single component lining in order to allow freeze plane changes caused by wear, infiltration and temperature changes of the furnace.??Resistance against mechanical wear from cleaning tools and stirring in order to allow maximum output without equipment downtime due to maintenance.??Resistance against thermo-chemical attack from aluminum and alloying elements.However, refractory materials with a low thermal conductivity typically possess a higher porosity and this leads to lower strengths and resistance against chemical attack and wear. Hence, as a compromise, multi layer linings are required in order to meet energy saving standards.In this paper we present the features of chemically phosphate bonded dense and light weight refractories and how such refractories can contribute to energy savings.IntroductionIn several reports, the U.S Department of Energy published theoretical energy requirement limits for aluminum production as a future target, with recommendations on how to reduce energy losses. The reports provide a basic description of the processes and equipment involved, their interrelationship, and their effects on energy consumed. The report uses onsite process measurements as benchmarks that industry uses to compare performance between facilities and companies [1]. The energy consumptions used in this paper are primarily based on numbers published by the Department of Energy. However, their reports do not consider the potentially significant energy losses from process interruptions due to a lack of preventive maintenance and material deterioration over time. Further, the Department of Energy reports do not consider equipment costs and availability. Energy input to metal output depends on factors beyond energy losses through the furnace wall. For instance, a focus on energy savings should consider fixed output costs due to depreciation of the equipment and the plant."

Jan 1, 2009

By C. Y. Haas

Of all the industrial clay minerals, attapulgite probably enjoys the widest variety of applications. A review published over three years ago by Haden and Schwint (18) cited some 80 individual uses, a list which continues to grow. In its near half-century of commercial life, attapulgite has received a generous share of research study and patent development effort, both on the part of producers as well as consumers. This work has been divided between understanding the mineral's structure or properties and applying it to specific end-uses. Naturally, information gained from the former has pointed toward opportunities in the latter. References of particular significance are cited throughout the text. Attapulgite's variety of uses derives from the unique three-dimensional structure and needle-shaped particle form of this crystalline hydrated magnesium aluminum silicate. Its inherent colloidal and sorptive properties are well known, and distinguish it from its sister clay minerals. Attapulgite is characterized by its high surface area, porosity, sorptivity, and decolorizing power. Its slips or slurries are viscous and thixotropic, however, unlike bentonite are not flocculated by electrolytes. In Table I are compared the general properties of attapulgite, bentonite, and kaolin. The properties in Table I are documented in greater detail by the wealth of scientific literature which has been published on the composition (14)(15), structure (6)(16), surface (16)(4)(22)(24), adsorption (31)(4)(5)(25), rheology (10-11)(12)(13)(26)(27)(32), plasticity (30) (31), and chemistry (23)(3)(7) of attapulgite. Attapulgite is the principal mineral constituent (70 to 80%) of attapulgite clay as it is commercially produced in the Georgia-Florida area of the United States. As mined, this clay also contains 10 to 1S% montmorillonite, sepiolite, and other clays; 4 to 8% quartz, and 1 to 5% calcite or dolomite. (18) During processing, non-clay fractions are removed so that commercial products are enriched to 85 to 90% attapulgite. By wet processing (such as practiced in the

Jan 1, 1971

By A. Juganda, Jr. Bogin, J. Brune, J. Grubb, S. Lolon

"Face ignitions at the longwall face are a serious hazard in underground coal operation that can lead to a major mine explosion. Despite having methane monitoring system mounted on the shearer and at various locations on the longwall face, undetected accumulations of methane can still occur and result in face ignitions. With the use of Computational Fluid Dynamics (CFD), the interaction between the air flow at the longwall face and factors that contribute to the accumulation of methane around the longwall face can be modeled and visualized in great detail. The results confirm that the tailgate corner of longwall face is a critical area that is prone to face ignitions and needs to be properly monitored. The occurrence of roof falls on the tailgate entry inby the face and/or poor caving conditions behind the shields can pose a safety risk in the longwall operation. Poor gob caving can lead to insufficient face air quantity to dilute methane at the tailgate corner, while blocking of tailgate by a roof fall can carry methane contaminated air from behind the shields back into the face near the tailgate corner and pull the explosive gas zones (EGZs) inside the gob closer to the face. INTRODUCTION Ignitions of accumulated methane gas at longwall faces are well known to be among the major causes of methane explosion in underground coal longwall mining operations. Some of these ignitions can lead to major mine explosions, such as the Upper Big Branch mine disaster in 2010, in which methane migrated from the gob to the shearer cutting drum where it was ignited, resulting in a major mine disaster (Phillips, 2012). History has shown that, despite having methane monitoring systems mounted on the shearer and various locations at the longwall face and alarms set to 1% CH4 (Mine Safety & Health Administration, 2012), undetected accumulations of explosive methane-air-mixtures can still occur and result in face ignitions. Recent study by Verma and Brune (2016) state that frictional ignitions on longwall faces contributed to 379 incidents or 23% of the total 1,637 cases of face ignitions recorded from 1983 to 2014. The common cause of mine explosions usually involves poorly designed ventilation systems, insufficient ventilation, and inadequate monitoring in critical areas that are prone to methane accumulations. In longwall operation, the tailgate corner of the longwall face can be considered as one such critical area. On-site studies by Krog et al (2006) and Thakur (2008) show that increasing the longwall panel width may also increase cumulative methane emissions at the tailgate. There are also indications that increasing longwall face lengths can result in an increase of the void space behind the face under certain roof conditions (Schatzel et al, 2006). This may cause higher leakage rates from the face to the gob, thus reducing the amount of fresh air available at the tailgate."

Jan 1, 2017

With significant increase in steel output in the world the price of iron ores has been soaring recently. Especially, there is a strong demand for iron ores in China, leading to more attentions paid to developing low grade iron ores. In this paper mineralogy of nm-of-mine hematite ore was deter-mined, and coal-based direct reduction-magnetic concentration was successfully developed to beneficiate low grade hematite ore. Mineralogy analysis indicates that this hematite ore is a super fine refractory ore, with the main valuable mineral hematite being closely associated with quartz and distributing uniformly and mostly occurring within the size of 3~5J.lITI,leading to being difficult to beneficiate due to super fine hematite and only grading 28.83% Fetotal. This hematite ore failed to be effectively upgraded by traditional processes in trial tests, such as reverse flotation, gravity concentration, and magnetic separation, or the integration of the above processes. In contrast with adoption of the coal-based direct reduction-magnetic separation process, concentrate was produced with high iron grade and metallization degree in the present work, which provides a theoretical basis for utilization of low grade iron ores. By optimization of direct reduction conditions, such as reduction temperatures, duration and mass ratio of reductant coal to iron ore, the reduced ore with 93.72% metallization degree was prepared, and then three-stage grinding-magnetic separation of the reduced ore were conducted, the final concentrate was manufactured, assaying 69.54% Fetotal and 98.01 % metallization degree, and with low content of impurities. This iron concentrate with high metallization degree produced by this process is a superior burden for converter instead of blast furnace. This process is enviromnent friendly by directly making iron using coal and iron ores instead of coke, resulting in less emissions and low production cost.

Jan 1, 2014

By Hylton McWhinney, Doanh Tran, Jewel Andrew Gomes, George Irwin, Sameer Pallavkar, Md Islam, David Cocke, Mohammad Rafiqul Islam

"High-performance nickel-based nanocrystalline zinc oxide adsorbents have been prepared adjusting Ni/Zn mol ratio of 1 :5 by thermal decomposition, coprecipitation and sol-gel method for selective adsorption of thiophene in liquid hydrocarbon fuels at ambient temperature and pressure. To understand the nature of reactive adsorption of thiophene (C4H4S) on Ni/ZnO, the effect of preparation techniques, morphological and textural structure on the desulfurization activity was investigated. A model fuel (20 mL) consisting of pentane (C5H12) and thiophene was prepared and adsorption experiments were performed by a batch method under ambient conditions. The physicochemical behaviors of the fresh adsorbents were obtained using X-ray diffraction (XRD) with EDAX, scanning electron microscopy (SEM). The sulfur concentration in the mixture was monitored by UV-vis spectrophotometry. The adsorption reaction confirmed that ZnO played a crucial role in taking up S element to convert it into ZnS. The deposition of nickel on ZnO is an innovative approach which takes advantage of the selectivity of Ni towards S-species and the high adsorptive capacity of ZnO support.IntroductionLow temperature deep desulfurization of fuels via selective adsorption of sulfur compounds keeping coexisting aromatic hydrocarbons and olefins intact is receiving increasing attention in the research community worldwide in order to satisfy the upcoming environmental regulations and fuel specifications. The sulfur compounds in the transportation fuels is a matter of concern when global crude oil slate is becoming heavier and sourer and environmental restrictions on both the refining process and the refined products are becoming more stringent. According to the current refinery technologies, the sulfur content in refinery fuel is typically around 300-500 ppm by weight (ppmw) [1-3]. Starting in 2006, sulfur limits in highway diesel and gasoline were set to 15 ppm and 30 ppm, respectively. During combustion sulfur in the fuel are converted to toxic sulfur oxide (SOx) and contributes to air pollution and acid rains [ 4]."

Jan 1, 2011

By P. S. Arthur

The copper I SAS MELT? process is a submerged lance bath smelting technology. In the 20 years since the process was first demonstrated on a semicommercial scale at Mount Isa in north-west Queensland, Australia, copper ISASMELT? plants have been constructed to treat concentrates or secondary raw materials around the world. The process is operating in smelters in Australia, the USA, Belgium, India, Germany, China and Zambia. ISASMELT? plants have been installed to improve the environmental performance of operating smelters and reduce costs for smelting companies. A new copper furnace is being commissioned at Southern Peru Copper Corporation in early 2007, while more furnaces are under design for installation in Kazakhstan and Peru. Copper ISASMEL T? plants are supplied as complete technology packages including engineering design services for the furnace and key ancillaries, supply of core equipment, provision of intensive training programs in operating plant environments and commissioning assistance services. The proven technology transfer process ensures successful implementation of submerged lance bath smelting into large scale plants. This paper summarises developments at recently constructed copper ISASMELT? plants.

Jan 1, 2007

By A. Lebedev

Application of dynamic simulation for a base metal processing plant is discussed. The plant receives ore of variable quality from two pits and blending had to be applied to maximise recovery. The plant employs multiple stage crushing, screening, dense media separation, two-stage milling, flotation and further filtration. Stockpiles and bunkers are used in the plant to cater for breakdowns and operating delays, the latter being appropriately incorporated in the model. A detail dynamic simulation model was constructed from the rock face to the filtration plant to assist the plant design, notably with definition of the ore blending method, sizing storage capacity and in-plant conveyors. The plant model was broken down to capital equipment items and various feed types and mass balances were tested to ensure that the production target is met. The dynamic simulation tested the proposed blending method, identified bottlenecks, produced risk profiles for all strategic storage facilities and overall helped minimise the project risks and improve confidence in the plant design. Keywords: Dynamic simulation, ore grade, blending, capacity, risk profile, throughput, utilisation

Jan 1, 2020

By Brett Schug, Caelen Anderson, Sohail Nazari, Carlos Cristoffanini

"The Haile gold mine in South Carolina is increasing the automation level of its processing plant in order to improve operational stability. One step toward this goal is the application of a digital twin concept to provide virtual instruments. Haile has engaged Andritz to implement virtual instruments at its grinding area hydrocyclones and at its tailing thickener underflow pump. These virtual instruments provide density values in a traditionally difficult location for reliable slurry density measurement. The digital twin is a first-principles integrated design engineering with advanced simulation (IDEAS) simulation model, connected in real time to the control system. Results have been promising, with the virtual instrument values matching the physical instrument under normal operating conditions and showing better prediction under upset conditions. Haile plans to use the virtual instruments as optional process control parameters.OceanaGold’s Haile gold mine is located near Kershaw, SC, about 80 km (50 miles) southeast of Charlotte, NC. This location was first mined in 1827 and has produced gold through several operating periods since then, including a heap leaching operation from 1985 through 1992. In October 2015, OceanaGold acquired Romarco Minerals, the previous owner of the Haile operation.The current operation began in 2017 as an openpit mine with additional underground resources. The nameplate throughput is 5,760 t/d (6,350 stpd) ore, and 2017 production was 3,345 kg (118,000 oz) gold, with 3,968 to 4,384 kg (140,000 to 155,000 oz) gold expected in 2018. Proven and probable reserves exceed 85 t (3 million oz) gold at a grade of 2 g/t (0.06 oz/st) gold. The process, as shown in Fig. 1, includes a primary jaw crusher, comminution with a semiautogonous grinding (SAG) mill and ball mill circuit, flash flotation, rougher flotation, regrinding, pre-aeration, carbon-inleach leaching, carbon elution and regeneration, cyanide recovery, electrowinning and refining. The Haile operation’s inaugural gold pour took place Jan. 20, 2017. Mine life is expected through the year 2030."

Dec 1, 2018

By C. Anderson, B. Schug, C. Cristoffanini, S. Nazari

The Haile Gold Mine in South Carolina is increasing the automation level of their processing plant in order to improve operational stability. One step towards this goal is the application of a Digital Twin concept to provide Virtual Instruments. Haile has engaged ANDRITZ to implement Virtual Instruments at their grinding area hydrocyclones and at their tailing thickener underflow pump. These virtual instruments provide density values in a traditionally difficult location for reliable slurry density measurement. The Digital Twin is a first principles IDEAS1 ™ simulation model, connected in real time to the control system. Results have been promising, with the virtual instrument values matching the physical instrument under normal operating conditions, and showing better prediction under upset conditions. Haile plans to use the virtual instruments as optional process control parameters. INTRODUCTION OceanaGold’s Haile Gold Mine is located near Kershaw, South Carolina, about 50 miles southeast of Charlotte, North Carolina. This location was first mined in 1827, and has produced gold through several operating periods since then, including a heap leaching operation from 1985 through 1992. In October, 2015, OceanaGold acquired Romarco Minerals, the previous owner of the Haile Operation. The current operation began in 2017 as an open pit mine with additional underground resources. The nameplate throughput is 6,350 tpd ore, and 2017 production was 118k oz gold, with 140 to 155k oz gold expected in 2018. Proven and Probable reserves exceed 3 Moz. The process, as shown in Figure 1, includes a primary jaw crusher, comminution with a Semi-Autonomous Grinding (SAG) mill and ball mill circuit, flash flotation, rougher flotation, regrinding, pre-aeration, carbon in leach (CIL) leaching, carbon elution and regeneration, cyanide recovery, electrowinning and refining. The Haile Operation’s inaugural gold pour took place January 20, 2017. Mine life is expected through at least the year 2030. Based partially on prior experience of some key OceanaGold personnel with automation services from ANDRITZ on other projects, OceanaGold decided to include ANDRITZ on the Haile project. The scope of these services for Haile included design and supply of the process control application software, an ANDRITZ dynamic process simulator for operator training, and ANDRITZ Advanced Control Expert (ACE) ®2 systems for the SAG mill, ball mill, and rougher flotation areas. Since startup, ANDRITZ has continued to provide services for the site, particularly related to PLC and HMI equipment, programming and support, ACE system expansion, and the implementation of Virtual Instrumentation. The implementation of this new Virtual Instrumentation technology at Haile is consistent with Haile goals: increased automation, a change in the role of the operator from interactor to monitor, and improved stability by removing human error.

Jan 1, 2019

By B. R. Mohal, F. F. Aplan, S. Chander

"ABSTRACTThe wetting behavior of coal has been determined in the presence of nonyl and octyl series of nonionic surfactants containing polyethoxy groups of different sizes. The wetting behavior was determined by a modified Walker technique and contact angle measurements. The results show that the wetting rate of coal varies with coal rank, structure of the hydrocarbon chain and number of ethoxy groups in the hydrophilic group of the surfactant. A close relationship has been observed between the wetting rates and the short-time advancing contact angles.INTRODUCTIONNonionic surfactants are used in many applications to improve wettability of solids. They can be used as dispersing agents [ 1 ] or dust suppressants [ 2-5 ] and to control the flotation, flocculation, filtration and flowability of particulates. This study was undertaken to study the effect of a series of nonionic surfactants on the wetting behavior of coal. Two series of surfactants, namely, ethoxylated nonyl and octyl phenols were used. The nonyl phenol series contains a linear hydrocarbon chain containing nine carbon atoms ( CH3( CH2 )8-C6H4,- ( OC2H, ) n, where n is the number of ethoxy groups) . The octyl phenol series contains a branched hydrocarbon chain containing eight carbon atoms ( ( CH3 ) 3CCH2C ( CH3)2-C6H4- ( OC2H4) n ).Initial wetting rates — modified Walker techniqueWalker et al. [ 6 ] developed a sink test to determine the wettability of coal particles. In this technique, coal particles are dropped individually onto the surface of surfactant solutions of different concentrations, and the most dilute concentration in which coal would sink ""instantaneously"" is determined. This technique is a variation of a procedure initially developed by Draves and Clarkson [ 7 to determine the effect of surfactants on wettability of cotton fibers. In this procedure commonly known as the Draves test, the concentration of a surfactant required to give a 'sink time' of 25 s is determined.Other investigators have used slight variations of the Walker method to study the wetting of fine particles [ 8-12 ] , by measuring the time for wetting a given amount of powder. There are differences in the manner in which the time of wetting is measured, however. Some investigators measure the time for the last trace of coal to disappear [ 8,11 ] whereas others determine the time for the vast majority of particles to sink [ 10 ] . Some investigators report a wetting rate [ 11 ] which is a value calculated on the basis of the time for the 'last traces of particles to sink'. The differences in choice of criterion for wetting can result in different values for wetting rates as illustrated in Fig. 1 which is based upon our measurements of the amount of powder wetted as a function of time. The procedure for wetting rate measurements is described in the next section. The technique in which time for disappearance of the 'last traces of particles' is determined gives the smallest value for the wetting rate, while the technique in which the time for wetting of the 'vast majority' of particles is determined will give intermediate rates. The terms 'last traces of particles' and 'vast majority of particles' are usually not defined explicitly and can lead to large differences in wetting rates measured by different investigators. Since our measurements show that the wetting rates for an assembly of powder decreases with time, we have used the initial wetting rates to compare the wetting behavior of coal in solutions of different surfactants."

Mar 1, 1989

By Edward H. Eisenbrey

This paper is primarily concerned with the exploration for massive sulphide orebodies. In a discussion of this type, it seems appropriate to establish a few definitions so that all parties may consider the same beast and its habitat. First, the term "massive sulphides", as used here, not only denotes a body of mineralized rock containing in excess of 50% sulphides by volume, but a mass of sulphides that respond as a conductor to the electromagnetic (EM) systems currently in use in exploration. "Disseminated sulphides" refer to all of those sulphide occurrences that respond to the Induced Polarization (IP) geophysical methods most commonly in use in porphyry copper exploration. This latter definition may also include the disseminated sulphide halos so frequently found associated with massive mineralization as well as banded and stringer sulphide mineralization. It is plain to see that these two end members of our definitions can easily blend into each other. The term "volcanogenic" refers here to any and all geologic processes that have their origin in volcanic activity. Thus we are concerned here with the exploration for massive sulphide ore deposits derived from and affected by contemporaneous and post mineral volcanic activity. Furthermore, most massive sulphide deposits are apparently formed in a submarine environment, deposited with extrusive rocks and sediments and/or chemical hot spring accumulations, then enclosed and protected by the addition of more volcanic and sedimentary material then, probably folded and deformed into one of their myriad of shapes.

Jan 1, 1973