Search Documents

By J. D. Allen

In the coal preparation plant at U.S. Steel Corp.'s Concord mine in Alabama, the product moisture was reduced from about 20% to 9% through the development of a workable flowsheet for dying the clean coal. Some of the high points of the conversion of the Concord washer from vibrating screen dewatering to centrifuge drying are presented in this article. The coal preparation plant at the United States Steel Corp.'s Concord mine near Bessemer, Ala., began operations in June, 1950. The basic cleaning circuit consisted of a Chance cone for cleaning the 2-in. x 3/8-in. fraction and concentrating tables for cleaning the -3/8-in. coal fraction. Dewatering of the final product was accomplished with 35-mesh vibrating screens. However, because Concord coal is very friable with 85% passing 3 mesh and 25% passing 28 mesh (Fig. I), a considerable quantity of fines passed through the dewatering screens. To recover these fines, the dewatering screen effluent was sent to two 70-ft-diam hyd rose para tors from which the underflow returned to the dewatering screens and the overflow went to a 175-ft-diam thickener for water clarification, as illustrated in Fig. 2. As might be expected, there was considerable recirculation of the -35-mesh coal in this system. This degraded the coal and led to higher moistures. It also resulted in a fines bleed-off of plant water and thickener underflow to a fine-coal settling pond. In 1961, vacuum filters were installed to supplement the screens and to recover the fine coal lost in the bleed-off. The above system resulted in a product moisture of about 20%. Further reduction to approximately 11% was accomplished by drainage from railroad cars during transit to the coke plant. Control of the moisture at unloading was poor because of variations in operating levels and railroad car availability, but since the Concord coal constituted a relatively small percentage of the over-all coal mix at the coke plant, its high moisture and fluctuations did not seriously hamper coking operations. Early in 1964, however, the proportion of Concord coal was increased with a resulting increase in the moisture of the total coal mix, and this caused difficulties in the coke plant. The increased participation of Concord coal also brought about a shortage of railroad cars which raised the moisture content to a point where the coal became almost impossible to handle. In an effort to alleviate this problem, U.S. Steel initiated a research program to develop a flowsheet for reducing the moisture to approximately 10% and to determine whether the resulting product would be satisfactory for the coke plant. Under this program, an experimental flowsheet for evaluating both a vibratory centrifuge system and a solid bowl centrifuge system was drawn up as shown in Fig. 3. A horizontal vibratory centrifuge was installed to reduce the moisture in the dewatered coarse coal, and a four-cell, flotation machine was installed to clean the -65-mesh portion of the 3/8-in. x 0 table raw coal feed. Several shortcomings in the above circuits were apparent. For one thing, large quantities of repulping water were required. Furthermore, since about half of the flotation feed was of a size consist that could have been cleaned on the tables, these circuits would result in an unnecessary increase in reagent costs and facilities. Maintenance of the hydro separators and pumps for pumping the underflow to the filters,

Jan 1, 1969

By David Young

This paper presents tunnel design considerations for the SR75/282 Transportation Corridor Project in Coronado, California. The project is managed by the City of Coronado in cooperation with Caltrans and the US Navy and may include a one-mile long twin-tunnel section with two options: a 36.5 foot diameter twin-bored tunnel or a twin cut-and-cover box. The alignment crosses the Coronado Fault, and design provisions were needed at the fault crossing to maintain life safety and prevent rapid inundation of the tunnel in the event of fault rupture. These provisions are discussed along with considerations related to liquefaction and ground shaking. The project is currently in the planning stage with construction to start around 2012.

Jan 1, 2008

By R. V. Higgins

This report presents the results of a study of gas injection in the Upper and Lower Terminal zones in fault block VB and in the Upper Terminal zone in fault block VI, Wilmington field, California. This report is based on data obtained to January 1956. Earlier studies of gas injection in other California fields have been reported .3/ The Upper and Lower Terminal zones, fault block VB, have been producing oil since 1945 and the Upper Terminal zone, fault block VI, since 1948. Before starting the gas-injection project, the expansion of dissolved gas was the principal mechanism moving the oil to the wells. Gravity drainage and an edgewater drive also have contributed to the movement of the oil to the wells. When the gas injection was begun, the reservoir pressure and the oil production had declined appreciably. Gas injection was started in the Upper and Lower Terminal zones, fault block VB, in May 1953 and in the Upper Terminal zone, fault block VI, in October 1953.

Jan 1, 1957

By K. Duckworth

"Comparative tests of the conventional Turam survey configuration and an alternative configuration called the Tx-parallel configuration were conducted at the McClean uranium deposit in northern Saskatchewan. Both configurations detected the known conductors at the site but the alternative configuration demonstrated its particular effectiveness in the reconnaissance role. This effectiveness results from the fact that the length of Tx-parallel traversesis controlled only by the length ofthe transmitter and not by its power. In addition, the field strength along a Tx-parallel traverse is uniform unless the traverse approaches the end of the transmitter. This freedom from a strong gradient of the primary field along a Tx-parallel traverse eliminates the gradient-induced anomaly shifts which are common in conventional Turam operations. The locations of each of the McClean conductors, that were obtained from the Tx-parallel profiles, werein better agreement with the locations known from drilling than were the locations obtained from the conventional profiles. However, the conventional profiles gave better estimates of the conductance of the targets.The results obtained over the McClean conductors indicate that current gathering has a strong influence on Tx-parallel results with consequent unpredictable influence on depth and conductance estimates. However, the depth estimates obtained from the Tx-parallel data appear to be in good agreement with the known depth of the McClean south conductor. The Txparallel results provide shallow estimates of the depth of the McClean north conductor which suggest that the fracture zone above the graphitic conductor is a significant conductor as was also suggested by earlier VLF surveys.Comparison with the wide range of published geophysical test surveys for the McClean site showed that apart from the work required to lay the transmitter, the Tx-parallel mode of operation of a Turam exploration system is operationally very similar to a moving source Slingram type of survey. At the McClean test site, it provided the same depth of exploration as a conventionally deployed fixed loop transmitter."

Jan 1, 1988

By Enrique Fernández

INTRODUCTION The high speed rail link between Madrid and Asturias, in the North of Spain, has encountered in the Cantabrian range the biggest challenge of the whole line, a very deep tunnel, 25 km long through a foreseen difficult geology. This tunnel was divided in the following four lots for construction: ¦Lot 1: Pola de Gordón- Folledo. L=10,7 km ¦Lot 2: Folledo-Viadangos. L=4,166 m ¦Lot 3: Viadangos- Los Pontones. East tube. L=10,4 km ¦Lot 4: Viadangos- Los Pontones. West tube. L=10,4 km. Dragados S.A. leading a JV was contracted to design and built the Lot 2 on the captioned Pajares High Speed Railway Tunnel. The Lot 2, comprising the middle third section of the 25 km long tunnel has an additional challenge: the construction of one access from the surface to allow it own construction. Feasibility reports and preliminary design do not foresee the use of TBM due to the risk of squeezing ground at the deepest area of the tunnel. On the other hand, conventional NATM excavation of the twin tunnels and ancillary works, including access shafts were against the expected construction schedule by the client, due to the poor ground foresee at the early stage.

By Ilpo O. Auranen

Background: Mines of today are moving ever increasing tonnages of rock. The new ore bodies tend be of lower grade and located deeper in the earth?s crust. The industry?s focus to overcome this ?deeper but poorer? ore problem has traditionally been to lower the costs by increasing the scale of mining. This has resulted in an ever increasing size of mining equipment like drills, loading shovels, dump trucks. The main focus has been in reducing the cost per ton of mining. This cost focus has often resulted in increased waste rock dilution and more ore losses. From costs to value: Waste rock dilution means waste rock in the concentrator feed. It?s value in open pit mining is equal to the value of ore it replaces. In underground mining, waste rock dilution?s value is equal to the value of ore it replaces added to the costs of mining it. It is commonly accepted that waste rock dilution in open pit mining ranges between 5 and 20% and in underground mining between 5 and 40 % . In a typical large open pit mine ore value is from 20 to 60 USD per ton and mining costs are 1 to 3 USD per ton. One percentage point reduction in waste rock dilution represents savings corresponding to about 20% of total mining operation costs. The difficulty of reducing waste rock dilution comes from the complicated nature of the ores. Accurate ore waste-border detection has not been possible due to excessive costs. Core drilling combined with geochemical lab analysis is the most accurate method for locating ore waste borders. However, it is also expensive and time consuming, which is why it is often combined with somewhat lower cost methods like sampling drill cuttings from blasting drill holes or from reverse circulation drills and analyzing them in a laboratory. The main drawback with these methods, in addition high costs, lies in the sampling accuracy and in the quality control of the whole process when a large number of samples have to be handled manually. In every mine it is possible to halve waste rock dilution by using new on-line analysis technology .

Oct 1, 2009

By Keith A. Heasley

The LaModel program has been used successfully in the United States for many years to design pillars to ensure global stability of pillar recovery operations. However, the recent Crandall Canyon Mine collapse showed that further research was required to improve the design of pillar recovery under deep cover. Toward this end, a new calibration procedure was implemented in LaModel. This calibration procedure prescribes techniques for calibrating the critical LaModel input parameters based on empirical abutment loading and pillar strength, as utilized in the time-tested ALPS and ARMPS programs. The calibration procedure is intended to help guide a novice modeler in choosing calibrated input parameters that produce a standard model that fits within the verification database. However, the rigid parameter specification incorporated in the calibration procedure also removes most of the flexibility in LaModel for specific calibration to the unique conditions at a given mine site. In this paper, a number of the LaModel input parameters are varied outside the bounds of the suggested calibration and the effects on the model results are analyzed. Ultimately, it is shown how the LaModel user might vary certain input parameters to adjust the model to site-specific conditions, while still maintaining the general accuracy and philosophy of the recommended calibration.

Jan 1, 2012

By David L. Borusiewicz, M. Suri Surendra

"Abstract Helical piles have been used as anchors and for supporting lightly loaded structures as a method of underpinning, etc in the past. Recently, helical piles are being used to support new structures because of their simple installation process using relatively light and mobile equipment. This paper presents the results of evaluation and design performed for the temporary support of existing piers during a bridge rehabilitation project.INTRODUCTIONThe helical screw foundation was invented and patented by Alexander Mitchell in England in 1833. He installed screw piles to support lighthouses in the tidal basins of England. Many applications in the earlier years in the USA were in North Carolina and in Florida to support lighthouses (in coastal plain deposits). A lighthouse of similar foundation design is still in use at Key Biscayne, Florida.In the USA, the helical piles were reintroduced as foundation elements for electrical transmission towers. Helical piles were also used for anchoring guys of self supported towers and as tie-backs for excavation support systems. Typically, helical piles are being used for supporting lightly loaded buildings and for underpinning buildings undergoing distress as a means of remediation. The helical piles are not commonly used in the transportation industry.HELICAL PILESHelical pile is a segmented deep foundation system with helical bearing plates welded to a central steel shaft. Load is transferred from the shaft to the soil through these bearing plates. Central steel shafts are available in either a square shaft (Type SS) or a round shaft (Type RS). The Type SS series are available in 38 mm to 57 mm square sizes. The Type RS series are available in 73 mm to 114 mm diameter sizes. Type SS-RS combinations are also available for compression applications in soil conditions where dense/hard soils must be penetrated with softer/loose soils above the bearing strata.The leading segment consists of a shaft with one or more helical plates that are welded to the shaft. The plates vary in diameter from 203 mm to 355.5 mm and have a thickness of 9.5 mm or 13.7 mm. Typically the plate diameter increases from the bottom of the shaft upward. A helical bearing plate or helix is one pitch of a screw thread. All helices, regardless of their diameter, have a standard 76 mm pitch. Being a true helical shape, the helices do not auger into the soil but rather screw into it with minimal soil disturbance. Helical plates are generally spaced a distance of two to three times the diameter of the plate directly below in order for them to function independently as individual bearing elements. A typical detail of helical pile is shown on Figure 1."

Jan 1, 2014

The achievement of high availability of the Grey River Gold Mining Limited's alluvial gold dredge is a tortuous task which will rely upon the dedication of all staff employed at Grey River Gold Mining Limited (GRGML). The persistent adoption of new technology and better operating procedures, combined with a strong commitment to preventative and predictive maintenance, is necessary. The Grey River Gold Mining Limited alluvial gold dredge is operating in a relatively low grade alluvial gold deposit and hence relies on a high throughput of ore to be profitable. To achieve the required high material throughput the dredge incorporates an overburden removal system which operates simultaneously with a conventional bucketline system.   The overburden system incorporates a cutter wheel and suction pump configuration which is dedicated to removing the low grade (5 mg gold/m3 gravel) overburden. The bucketline conveys the richer grade payzone gravels (up to 890 mg/m3 gravel) to the recovery plant mounted onboard the dredge. The horizon for the overburden system approximates 15 m and the payzone terminates at the interface of the old man rock and the alluvial gravels at a variable depth averaging 22 m.   From a mechanical engineering perspective the dredge is a machine comprised of two materials handling systems which are controlled by Operations Staff and electronic process control systems.   The availability of such a materials handling system is a function of four variables: 1. The environment that the machine operates in. 2. The ability of the people operating the machine. 3. The design of the mechanisms, the configuration that they are grouped in and the effectiveness of the process control systems which control the mechanisms. 4. The procedures utilised to predict the performance of the machines and the skill of staff to analyse that data and carry out effective maintenance.

Jan 1, 1989

By P Lindsay, J B. Hughes

Underground and opencast coal mining has been ongoing since 1896 on the Stockton Plateau, West Coast, New Zealand. Acid Rock Drainage (ARD) from historic and current mine workings has had an adverse environmental impact on the surrounding aquatic environment. The two main catchments affected by ARD are those of the Mangatini and St Patrick streams. These catchments flow into the Lower Ngakawau River, which holds high amenity value for the local community. Water quality targets set by Solid Energy for 2010 in the Ngakawau River include increased pH and clarity and a decrease in certain dissolved metals.   At-source ARD minimisation options are the first stage in mitigating the effects of mining acid forming rocks and reducing acid loads in the Mangatini and St Patrick stream catchments. ARD minimisation techniques reduce the quantity of acidity generated and thus reduces the treatment required. Treatment will be required for many years at Stockton due to current and historical acid formation. This paper looks at the treatment options that Solid Energy has been investigating including limestone leach beds, engineered wetlands, oxic limestone drains, and limestone dosing of catchment drainage. Particular focus is given to fine limestone dosing of the Mangatini stream and subsequent water quality improvements.

Jan 1, 2007

By M. Rafie, M. Rinne, F. Samimi Namin

"SynopsisRock mass classification systems constitute an integral part of empirical underground excavation design. One system that is commonly used to classify rock mass is the Rock Mass Rating, or RMR, system. The RMR system has evolved over time to better reflect the perceived influence of various rock mass factors on excavation stability. While the introduced modifications have enhanced the applicability of this classification system, there are still areas that cause potential ambiguity. The RMR system cannot deal with input data ambiguities, uncertainties, and vagueness. To deal with the uncertainty, a Fuzzy Rock Mass Rating (FRMR) has been developed. This study aims to describe the main concept of the fuzzy approach, which is implemented in the FRMR to classify rock mass. The FRMR considers the uncertainty associated with the input data (uncertain variables) used in rock mass classification. The Gol-e-Gohar (GEG) area 3 iron ore deposits in the south of Iran were chosen as the case study for investigating the applicability of FRMR. The results of this study show that the FRMR software tool can easily be used for rock mass classification, even if uncertain input parameters have been used. FRMR consists of three parts, each of which is suitable for certain conditions.IntroductionNowadays, rock engineering classification systems, which constitute the backbone of the empirical design approach, are widely employed in both civil engineering and mining engineering. Rock mass classifications have recently been quite popular and are being used mostly for the preliminary design and planning purposes of projects. According to Bieniawski (1989), a rock mass classification scheme is intended to classify the rock masses, provide a basis for estimating deformation and strength properties, supply quantitative data for support estimation, and present a platform for communication between the exploration, design, and construction groups."

Jan 1, 2015

By L Torckler, R L. Brathwaite

At Neavesville gold-silver (electrum) mineralisation occurs in steeply-dipping zones of intense fracturing, brecciation and quartz veining within rhyolitic pyroclastics, carbohaceous shales and andesites. Hydrothermal alteration extends over an area of greater than 3 by 1.5 km. In rhyolitic tuffs, highly silicified zones containing quartz-adularia-illite assemblages are flanked by less silicified assemblages composed of albite, illite-montmorillonite and chlorite. The mineralogy and sequence of alteration are comparable with the alteration zones which envelop the steam-producing fissures of the active Wairakei and Broadlands geothermal fields. Primary fluid inclusions in quartz from five fissure veins in the Neavesville field show maximum homogenisation temperatures ranging from 220 - 260¦C and salinities of 0.0 - 1.1 wt per cent NaCl equivalent, which cover a similar range to actual measured temperatures and salinities in geothermal fluids at Wairakei and Broadlands. The age of the rhyolitic pyroclastics and related alteration and mineralisation is probably Pliocene and Neavesville therefore represents a fossil geothermal system. The intensely fractured zones containing the gold-silver mineralisation were probably produced by hydraulic fracturing generated by accumulation under pressure of hydrothermal fluid in blind fault zones. Study of fluid inclusions indicates that hydrothermal quartz associated with electrum was deposited under boiling conditions. High grade electrum mineralisation at Graces workings appears to be localised by reaction of hydrothermal fluid with sedimentary marcasite in black shale.

Jan 1, 1980

By Frank B. Fulkerson

A study was made of the economic factors governing silver production in the Coeur d'Alene mining region, Shoshone County, Idaho. Production and other stat is tics were analyzed. It was concluded that if the rapid rise in the open market price that began late in 1961 continues, greater production of the metal should result from the mines of the Coeur d?Alene mining region. However, the output gain would be limited, because costs per ton of ore mined would rise as production was increased beyond optimum capacity. Advances in the price of silver would increase the size of ore reserves by making some marginal ore profitable to mine and by providing greater funds for exploration projects that might result in discoveries adding to the reserves. Output of byproduct silver from lead-zinc mining probably will not exceed 4.3 million ounces, judging from the trend from 1946 to 1961.

Jan 1, 1964

By Stephen Chung, Graham Mustoe, Joe Haid

In an open cast coal mining operation, a 305 m (1000 ft) long by 49 m (160 ft) thick overburden cast blast can produce more than a million cubic yards of broken muck that needs to be removed before the coal recovery process can start. In the Powder River Basin of Wyoming, it is common to see 30 to 40 percent of the overburden cast to a spoil that does not require rehandling with heavy equipment. Therefore, the higher the percent cast, the better the cast blast is rated. However, depending on the shape of the muck profile, there is often 20 to 30 percent of the muck standing in front of the high-wall. This portion of muck would require a number of dozers to push down to the dragline pad level. From the mine operator point of view, it is believed that for a given muck profile, there should be an efficient dozer pushing method such that a dragline pad can be developed in the shortest time. As a tool for analyzing this dynamic problem, a 2-D discrete element model, i-PushTM, has been developed to simulate a dozer pushing operation. This mechanistic model takes into account the dozer blade geometry, the dozer operating procedure (e.g. cut-depth, blade fill distance, forward and reverse speeds at specific slope angles), material density and cohesion. To demonstrate how i-PushTM can be used to help determine the most productive push routine, this paper presents three dozer push methods to compare the effectiveness of pushing at 3:1, 4:1 and 5:1 push angles.

Jan 1, 2006

A tectonic interpretation of the Coromandel Peninsula which suggests that the basement underwent tensional collapse at its northern and southern ends would permit more ready penetration of late stage magmatic fluids. This hypothesis is consistent with regional trends of the chloride content of low grade geothermal waters and of the yield of gold and silver per unit weight of quartz worked. The consequences of such a model are that mercury should not only be a good pathfinder for Coromandel gold, but that it should be correlative with ratios of base metals high in the zoning or paragenetic sequences to those lower in the sequences. This is demonstrated successfully in an area of mineralisation in the southern Coromandel.

Jan 1, 1987

"Polycom, a new approach to ore processing based on pressure comminution, is obviously a very attractive alternative to conventional processing methods.Since a full-scale pilot plant was commissioned in 1986, more than 125 commercial installations, with capacities up to 1000 t/hr, have gone ahead.Already successfully used in processing cement clinker, limestone, coal, and other minerals, Polycom high pressure grinding results in:o Significantly reduced capital costs, because smaller units can be used m new installations;o Capacity increases of up to 100% in existing facilities; and o Operating economies that include energy savings of 20% or more, and reduced wear parts consumption.1. IntroductionAutogenous or semi-autogenous mills in conjunction with rod or ball mills are used with preference for ore processing. Most ball mills are of closed-circuit design and operate with mechanical classifiers (spiral or rake classifiers) or hydrocyclones. In other words, the ores undergo wet primary grinding, since slurries are required for the downstream separation stages anyway. This paper presents a new grinding system based on high pressure comminution of ores. This grinding process allows:- Energy savings of up to 20 % or more- Capacity increases of up to 100 % and more- Reduction of wear costs- Smaller units for new installation and thus- Reduced investment costsThese advantages are highly interesting for both new installations and conversion projects, particulary in cases where an increasing hardeness of the ore, i.e. rising Bond Work Index, reduces the output of the plants or where the metal assay of the ore decreases and the capacity of the existing systems has to be increased. POLYCOM high-pressure grinding rolls have established themselves with great success already for grinding cement clinker, granulated blast furnace slag, limestone, cement raw materials, coal and other materials.Meanwhile more than 250 high pressure grinding rolls have been installed worldwide. Capacities up to 1.000 t/h with roller diameter up to 2.8 m and drive units up to 2.400 kW are installed."

Jan 1, 1991

By S. Hunt, D. de Vries

Kansanshi Copper Smelter began operation in March 2015. The smelter features a single Isasmelt furnace for smelting, one 6-in-line electric furnace for matte-settling and slag-cleaning duties, four Peirce- Smith converters and two rotary anode furnaces. A 1,450 t/day oxygen plant and a 4,085 t/day sulphuric acid plant are included in the smelter operations. This paper gives an overview of the operational performance to date with summary data for each smelter section. Challenges such as an unforeseen refractory failure in the Isasmelt furnace in 2016 are discussed. Design improvements around the electric furnace are mentioned. Plans for potential future improvements are put into context. A consistent focus on operations, maintenance and continuous improvement has seen the smelter easily achieve its nameplate capacity of 1.2 million tonnes per annum of copper concentrate throughput. The smelter now operates consistently at a concentrate throughput rate of 1.38 million tonnes per annum of copper concentrate. INTRODUCTION The smelter was commissioned in March 2015. Design and commissioning of the smelter have been discussed by de Vries, Hunt, Hanschar and Louie (2016). The smelter rapidly ramped up to achieve nameplate production (1.2 million tonnes per year concentrate) and in 2018 operated consistently at the rate of 1.38 million tonnes per year concentrate. This paper presents major operational data for each section of the plant and describes significant events and improvements during the first four years of operation. The smelter flowsheet is shown in Figure 1.

Jan 1, 2019

By Steve Tadolini

Underground roof falls can have devastating effects on the safety of operations personnel, and equipment, and seriously impact production. Immediate steps are usually taken to danger off and secure the area while clean-up efforts are designed and implemented. A critical step, often overlooked due to production demand, is the determination of - why the roof fall occurred so that additional occurrences can be avoided in future developments or what measures can be taken to identify areas that have similar ?symptoms?? Forensic engineering includes the investigation of materials, products, structures or components that fail or do not operate/function as intended. The authors define forensics in ground control engineering as the study of evidence discovered while examining underground roof falls by applying expert observational techniques and established mining engineering principles to determine the probable cause, hypothesize solutions, and design engineering safeguards to prevent reoccurrences. Simply stated, the primary steps in the forensics of underground roof fall techniques are: ? Assess regional and local conditions prior to the event. ? Assess post-event conditions. ? Hypothesize plausible ways in which the pre-event conditions ? became the post-event conditions.Search for evidence that either denies or supports the various ? hypotheses.Apply engineering skill to relate the various facts and evidence into a cohesive scenario of how the event may have occurred. This paper details the proposed technique by utilizing a roof fall case study that required the examination of five primary factors: mine design parameters, excavation geology, method of excavation, method of support, and mining cycle times.

Jan 1, 2009

By Michael I. Brittan, Craig M. Sams

"Economies of scale and the variable characteristics of many large ore deposits have resulted in grinding installations using very large SAG mills fitted with variable speed drives. Low-aspectratio single-stage SAG mills were introduced in South Africa to process the consistent gold bearing Witwatersrand quartzites. Elsewhere, circuits were patterned after the more conventional North American circuits with high-aspect-ratio SAG mills followed by ball mills. This paper provides information on two recent Gold Fields group installations covering both types of SAG mill in large, single-stage applications. While these operations process similar tonnages, the mills represent opposite ends of the aspect-ratio spectrum. The Tarkwa mine in Ghana employs a low-aspect 27’ x 42’ 14MW SAG mill. The St Ives mine in Australia operates a conventional 36’ x 18’ 13.4MW SAG mill.INTRODUCTIONGold Fields is one of the world’s largest gold producers with annual production of approximately 4.2 million ounces. The Gold Fields group has operations in South Africa, Ghana and Australia, along with numerous exploration sites and advanced projects in several other countries. This paper discusses new milling operations in Ghana and Australia.TarkwaThe Tarkwa Gold Mine is located in Ghana, West Africa, approximately 350 kilometers west of the capital city of Accra (Figures 1 and 2). The site conditions are tropical with an average annual rainfall of 1,930 mm and a maximum temperature of around 35°C."

Jan 1, 2006

THE object of this paper is to review certain features in connection with the mining of narrow lodes, say up to 20 ft. or so wide. The types of ore-body to which it is intended to refer are those which occur. chiefly as fissure or shear-Iodes-that is, those lodes which are to be found in belts of country which have been subjected to dynamic stresses, resulting in the formation of cracks and fissures, into some of which has been concentrated sufficient metal-bearing material to form ores. Very frequently one of the walls of such a lode is found to be a fault, or plane of differential movement.The first point which comes up for consideration is the shaft and its position. From the information afforded by the prospecting which has been done on a lode relative to the dip, nature of country, &c., the position of the main hauling shaft can be determined. For purposes of general utility the hangingwall is generally chosen, if a vertical shaft, though, on account of freedom from creeps, the foot-wall would be safer. Vertical shafts are preferable to underlie shafts in many ways; but wherethe lode maintains a flat dip the cost of cross-cutting at the various levels becomes very heavy'. This difficulty may to some extent be modified· by sinking a vertical shaft in the hanging-wall...

Jan 1, 1912