Search Documents

By Noel N. Moebs

Valley Camp No. 3 mine was the scene of an experimental shortwall introduced in 1973 in an attempt to improve the recovery from the Pittsburgh coalbed in the Ohio Valley area where adverse ground conditions have imposed partial extraction methods with only 40 to 55 percent recovery of the valuable resource. The Bureau of Mines, under a cooperative agreement with Valley Camp Coal Co., monitored ground pressures and caving in the shortwall section in an effort to determine whether the roof strata, notably the limestone main roof, will cave to the extent that roof pressures at the face are relieved and whether the powered roof supports can sustain the roof load. The Bureau's efforts included mapping of clay veins, instrumentation of chain pillars and shortwall panels with encapsulated pressure cells, recording hydraulic pressures in the legs of the shortwall chocks, and core drilling underground and from the :surface. The experimental shortwall was a qualified success. Recovery increased 5.4 percent compared with partial extraction. Pressures in chain pillars and the abutment zone were not excessive. Hydraulic pressures in the chock legs did not approach the yielding pressure. Apparently, the limestone strata caved and the roof pressure at the face was relieved.

Jan 1, 1976

By S Yuen, T Rana, S Khan

Many open pit mines require dewatering or need aquifer depressurisation systems to manage mine water inflow and/or mine floor stability. In many instances these mining operations impact on regional groundwater resources and therefore access to these resources by other users.As such potential exists for mine development to be hindered or even blocked by groundwater legislation that aims to prevent declining groundwater levels and demonstrate equitable use of a regional groundwater resource.There is a need to manage aquifer systems during and after the mining operations, and in some cases stresses on the aquifers and associated ecosystems may be elastic and can be managed with minimum impacts or reversed once the mine ceases to operate.This paper uses the Gippsland sedimentary basin, with a history of declining groundwater levels and mining and petroleum production, as a case study to pose the question: Should period of mining operation, aquiferÆs storage capacity and its ability to recharge be concurrently considered when granting groundwater abstraction and mining licenses for prospective mine development?It further examines that by utilising an aquiferÆs storage capacity and demonstrating an understanding of aquifer system hydrodynamics during and beyond the life of the mine (time), the approval process for groundwater abstraction and associated cost of statutory monitoring may be made less onerous.

Jan 1, 2009

This paper considers three aspects of cemented fill practice and research in Mount Isa. Firstly, an account is given of the use of Portland cemented hydraulic fill, considering mainly the role and specifications of the fill used but including û brief description of fill preparation and placement. Data resulting from a Portland cemented hydraulic fill sampling, curing and testing campaign covering about 18 months of operating practice are presented, analysed and discussed. These yield information indicating the mode of operation of a fully-automated fill preparation station, as well as a means of comparing field and laboratory strength results. A technique with potential for use as a fill quality control without actual strength testing is also described. Results of a fill research program conducted by the author in Mount Isa since early 1968 are presented, involving both Portland cemented hydraulic fill and alternative, cheaper, additives for cementing hydraulic fill.

Jan 1, 1971

MR. W. E. WAINWRIGHT occupied the chair, and in introducing the lecturer said, on account of the absence of the vice-president, it fell to his lot to introduce the lecturer. Mr. Tennberg, he said, was visiting Australia, and those present might wonder who he was.He understood that the lecturer w~s a reputable practising geophysicist, associated with a reputable company! It was rather desirable perhaps to say that the Institute had made some inquiries with regard to his status. Geophysics was a comparatively newscience, and had suffered several hard knocks in Australia and elsewhere. Most of those knocks had been the result of undue optimism of a number of people who did not understand what they were talking about. It had been claimed that geophysics was a...

Jan 1, 1930

By Y. I. Yang, Y. -B. Tang, D. -J. Ma

Chlorine-containing minerals are commonly present in coal. Associated minerals such as pyrite can undergo exothermic reactions. Consequently, it is of great significance to study the effect of inorganic chloride on the spontaneous combustion of coal. In this study, the effects of five inorganic chlorides (sodium chloride, magnesium chloride, potassium chloride, calcium chloride, and zinc chloride) on the spontaneous oxidation of coal were investigated. Analysis of the gaseous products of coal oxidization at low temperatures (323K to 453K) showed that the presence of inorganic chlorine in coal markedly decreases O2 consumption and the generation of CO and CO2. Samples of raw coal and chlorine-loaded coal were oxidized for 36 hours under the same experimental conditions. Infrared diffuse reflectance spectroscopy results showed that inorganic chloride can inhibit the oxidative decomposition of some functional structure components (methyl, methylene, methine, and hydroxy) in the coal. The influence of inorganic chloride on the oxidation characteristics of the functional groups in coal during spontaneous combustion was investigated using benzyl alcohol and 1-phenylpropanol as model compounds, which were tested under the same experimental conditions as the coal samples. The oxygen consumption of model compounds with and without the addition of inorganic chloride further suggested that inorganic chloride may hinder the oxygenolysis of these structures during low-temperature oxidation. This phenomenon can be attributed to the radical reaction from the perspective of radical chemistry. It can therefore be concluded that inorganic chlorides play an inhibitory role in the spontaneous combustion of coal.

Jan 1, 2015

By James Scott

Outline Deposit Overview and Brief History ?Geologic Setting ?Local Geology ?Petrography ?Geochemistry ?Mineralization ?Geochronology ?Conclusions Deposit Overview ?Porphyry Cu-Mo-Au ?Discovered 1957 (BIK Syndicate) ?Various programs, most significant: ?Hecla(1970s) ?Teck(Late 1970s Early 1980s) ?Copper Fox Metals (2005 -Ongoing ?optioned from TeckComincoin 2002) ?Measured and Indicated Resources: ?847Mt grading: ?0.292% Cu ?0.019% Mo ?0.202g/t Au ?1.796g/t Ag ?Total ~ 0.485 % Cu Eq.

May 1, 2006

By A. P. Whittlestone, J. D. Johnson, R. J. Pine, M. E. Rogers

standpoint. The effect on efficiency of collisions

Apr 1, 1995

The Mount Lyell Mining Field is Australia's chief productive source of copper. It is situated near Queenstown, on the western flanks of the West Coast Ranges, about 20 miles from the west coast of Tasmania (Fig. 1).The following observations on the mineral composition of the copper ores of the Mount Lyell Field are based on a...

Jan 1, 1939

By H. E. Nold

THIS paper is an effort to explain in a simple manner the fundamental principles involved in examining a clay deposit for both quantity and quality and in operating a clay mine, either open-pit or underground, so that the best quality of finished material can be made from the raw material available. The writer is aware that what is recommended in this paper is everyday practice in many refractories plants and in some other heavy-clay products plants, but observations made while visiting practically every clay mine in Ohio have convinced him that the practices herein discussed are not as widely used as their importance warrants. It is true that the problem of mining for quality is more acute in refractories plants than in most heavy-clay products plants, yet some of the latter are finding it profitable to pay more than ordinary attention to the selection and blending of their raw materials. It is hoped that this short paper may prove helpful to some who are now finding it difficult to produce a uniform product of as high quality as their clay deposit seems to warrant. The coordination of the work of the clay mine or pit with the manufacturing plant, to the end that the best product possible be made from the raw material available, presupposes a rather intimate knowledge of the clay deposit. The knowledge must include not only information of the amount of clay-available but also rather detailed information about both vertical and horizontal variations in quality of the clay. This information should cover three things: quality, quantity, and location.

Jan 1, 1929

By Solar D. Andrés

Several large open pit mines are facing the challenge to design and plan an underground transition to sustain the long term future of their operations. The desired underground method is Block Cave since its natural high productivity and low operating cost that could compete against the open pit cost to mine the final open pit pushbacks. It has been found at several operations where this transition is taking place that the pit limit at which transition is performed is rather deep. This aims to think that perhaps several transition projects have started late in the life of an operation producing an over stress in the transition project and reducing the flexibility in the design of the overall infrastructure and a substantial lost in the complete project NPV. Traditionally the approach to plan open pit underground transition consists of sequentially deciding the final pit using a Lerchs and Grossman type of optimization to find the overall maximum pit shell and then running block cave simulations to find the best footprint for the underground option. The research summarized in this paper is related to the development of an integer linear programming model that aims to compute simultaneously the maximum NPV of the combined option final limit open pit and block cave underground footprint. The model has been tested using two large block models representing two of the current operations in the process of transiting from open pit to underground operations. Finally, the integrated open pit underground transition model is going to be compared to the traditional sequential approach in order to define which method achieves the best NPV. The paper illustrates both case studies in depth.

Oct 1, 2009

By Robert H. Richards

My first paper, read at the Cobalt Meeting of the Institute,' July, 1907, dealt with the behavior of a small Wilfley table when collceiltrating galena from quartz, the table being fed with natural products, with sized products, and with classified products. Since galena, having a specific gravity of 7.5, is among the heaviest minerals ordinarily concentrated by Wilfley table, it was desirable that a similar set of tests upon a mineral of lighter weight should be made. Chalcopyrite, of a specific gravity of 4, would have been the best mineral for this purpose, on account of its great importance as an economic mineral, but in carrying out the test I was obliged to content myself with a cupriferous pyrite, the specific gravity of which was 4.68 and the content in copper 8.80 per cent. Through the kindness of H. 0. Cummins, this material was obtained from Shasta, Cal., in very pure, clean, homogeneous condition. It was broken by rolls to 2 mm. in size, taking care to make a minimum of slimes. The quartz used to mix with it was pure, white, New England quartz, broken in the same way to the same size. In studying the accompanying tables, it should be borne in mind that the material concentrated was of low copper-content, and in many cases the quantity fed to the machine was 1 kg. or less. As a consequence of the smallness of the quantity treated it was very difficult to adjust the table and get it in condition to do its best work before the feed became exhausted, and for this reason many results were obtained which appear irregular.

Jan 1, 1909

By G. Zhu

Bulk and differential laboratory flotation tests have been carried out using a synthetic mixture of chalcopyrite and molybdenum ore. In addition to boiling and roasting, six different depressants are tested so that the best conditions of separation can be identified. These reagents include sodium cyanide with and without zinc sulfate, potassium ferrocyanide, sodium hydrosulfide, arsenic Noke's reagent, and sodium sulfide. The data indicate that most of these reagents are effective chalcopyrite depressants. However, sodium hydrosul fide can be used preferably if economic, operational, and environmental factors are taken into consideration.

Jan 1, 1983

By W. W. Culver

The paper explores the substance, circumstances and significance of the Whelpley and Storer Copper Process. The 1866 Whelpley and Storer patent specified a process combining mechanical and chemical engineering. The process called for a down-drafting shaft furnace with a horizontal flue connected at the bottom of the shaft. Powdered sulphide ore was roasted in the shaft and then sent forward fully oxidized to a bath of sulphuric acid and/or calcium chloride. The “water furnace” was developed in Boston, at a time when the city was home to most Michigan copper mining companies. The process was field-tested at Quebec’s Harvey Hill copper mine. In 1865 James Douglas, Jr. took over management of the Harvey Hill mine with the challenge of saving the family investment. He needed a way to make money from low-grade sulphides. Through his relationship with chemist T. Sterry Hunt, Douglas learned of a possible way ahead using the process developed by Whelpley and Storer. The paper confirms the centrality of publications, meetings, and networking in the advancement of metallurgy. The process is of interest historically, as much as anything, because it is one of the pillars of James Douglas’ distinguished career in copper. INTRODUCTION At the 1866 meeting of the American Association for the Advancement of Science (AAAS) in Buffalo, New York, T. Sterry Hunt (1826–1892) read a paper “On the Metallurgical System of Messrs. Whelpley and Storer.” The paper is part of a chain of events that constitute the foundation of James Douglas’ (1837–1918) success in the copper mining industry. To understand the career of Douglas over the early years of modern copper mining, we must necessarily start with Whelpley and Storer. Going back to Hunt’s paper, he concluded his remarks by asserting that the Whelpley and Storer Process was “capable of such wide and varied application, that it is probably destined to have a very important influence on the industry of the world” (Hunt, 1867a). He reached this conclusion reasoning that the process had overcome a critical metallurgical hurdle (Hunt, 1867a). Hunt, a geo-chemist in modern terms, recalled that the chemist of those years easily separated copper from “sulphuretted” ores by converting it to a soluble salt from which pure metal was precipitated by “an equivalent of iron.” The problem was to “…apply this principle in the working of copper ores on a great scale...” (Hunt, 1867a). Hunt noted that this very problem had “…engaged the attention of many metallurgists, and has given rise to various processes for obtaining copper by the moist way, many of which are nearly or quite perfect in their operation, but are lacking in practicability and cheapness” (Hunt, 1867a). Hunt thought Whelpley and Storer had overcome the low-grade sulphide hurdle with a commercially viable engineering breakthrough. Yet in the history of copper metallurgy, the process is missing. What happened?

Jan 1, 2019

By E. N. Harshman

Uranium mining and milling are rather new industries in Wyoming and South Dakota, but, in the past 15 years, ore valued at more than $400,000,000 has been mined and milled in the region. The major uranium deposits are in structural and/ or erosional basins or on the flanks of uplifts. The principal host rocks are medium- to coarse-grained sandstones that were deposited in continental or brackish-water environments and were derived in large part from the granitic cores of the uplifts and the sedimentary rocks that flank the cores. The ages of the host rocks range from Cretaceous to Miocene, but more than 95 per cent of the known reserves in the region are in rocks of early Eocene age. The bulk of the ore in the region is unoxidized and lies below the water table; some oxidized ore has been mined in the Powder River Basin and Black Hills districts. The unoxidized ore comprises pyrite, uraninite and/ or coffinite, marcasite, hematite, jordisite(?), and selenium. Minerals in the oxidized ore include hydrous uranium carbonates, phosphates, and sulfates and hydrous uranium and/ or vanadium silicates. The deposits are in the form of ore rolls that contain from a few hundred to a few hundred thousand tons of ore, ranging in grade from 0.1 per cent to 1.0 per cent U3O8. The rolls are at the margins of large tabular bodies of sandstone that has been altered by the orebearing solutions. The deposits are believed to have resulted from the interaction of an alkaline; oxidizing, ore-bearing ground water and a reducing environment. Exploration guides include the spatial relations of ore to altered sandstone, favorable lithology in the host rock, the content of certain elements and/ or compounds in ground water, and the relation of deposits to major paleodrainages.

Jan 1, 1968

By Madan M. Singh

Hydraulic mining has been practiced in the United States since 1852 and many mineral commodities, such as gilsonite, phosphates, lead-zinc, silver ores and St. Peter Sandstone can be mined in this manner. In 1958, the U. S. Bureau of Mines initiated research into the mining of coal using these techniques.1-4 These early investigations were conducted in the 5000 psi pressure range. The large nozzle diameters used in this pressure range produced extremely high flow rates which created visibility problems at the coal face, and required removal of large amounts of water from the mining area. Besides, the production rates were not much better than with mechanical methods. This indicated that with higher pressures the water quantities might be reduced using the same or higher horsepowers but enhanced breakage. For this reason intensive investigation in material removal using fine water jets at extremely high pressures (50,000 psi to 100,000 psi) has been undertaken. This was not the entire reason for this contract from the Bureau of Mines, however. The contract objective is outlined later. IIT Research Institute has done pioneering work in high pressure jet development in the United States.5-8 Similar schemes have been investigated abroad. 9-13 Hydraulic mining of coal at relatively low pressures is successfully being done in the Soviet Union, Japan, Canada, and most recently, in Germany.

Jan 1, 1973

By Hillary W. St. Clair

Reaction rate coefficients were determined from analyses of the effluent gas for the reduction of granular ferrous oxide to metallic iron by passing carbon monoxide through a packed bed of oxide at a controlled rate in the temperature range 1,000° to 1,300° C. Coefficients were determined by the comparison of observed analyses and calculated analyses using a mathematical model that takes into account the nonuniform composition of both the solid oxide and the gas. A method is also given for finding the value of the rate coefficient that best fits the observed data.

Jan 1, 1968

By W. W. Adams

Three hundred and twenty-eight mines and quarries, representing 36 States, took part in the twelfth yearly accident-prevention contest conducted by the United States Bureau of Mines and known as the National Safety Competition. Four underground mines and one open-cut mine (which represents the quarry and open-cut mine group), each the leader in its group, were awarded the ?Sentinels of Safety? trophy. Relative standing in the contest" was determined by the number of days lost from accidents in proportion to the total number of man-hours worked. Since 1925, when the National Safety Competition was inaugurated, an increasing interest has been taken in it by mining and quarrying companies as a means of stimulating mine and quarry safety by competition among similar plants. Each participating plant can, on a basis of its standing and record in the contest, determine to what extent its safety program is succeeding or to what extent it needs strengthening. With this information, each company that has a low standing in the contest can intensify its safety-promotion efforts the following year to obtain a lower rate and possibly win the trophy or achieve honorable mention in the competition. Except for 1929, the National Safety Competition of 1936 represented more man-hours of employment than any other year since the yearly contests began.

Jan 1, 1937

By W. W. Adams

Three hundred and twenty-eight mines and quarries, representing 36 States, took part in the twelfth yearly accident-prevention contest conducted by the United States Bureau of Mines and known as the National Safety Competition. Four underground mines and one open-cut mine (which represents the quarry and open-cut mine group), each the leader in its group, were awarded the ?Sentinels of Safety? trophy. Relative standing in the contest" was determined by the number of days lost from accidents in proportion to the total number of man-hours worked. Since 1925, when the National Safety Competition was inaugurated, an increasing interest has been taken in it by mining and quarrying companies as a means of stimulating mine and quarry safety by competition among similar plants. Each participating plant can, on a basis of its standing and record in the contest, determine to what extent its safety program is succeeding or to what extent it needs strengthening. With this information, each company that has a low standing in the contest can intensify its safety-promotion efforts the following year to obtain a? lower rate and possibly win the trophy or achieve honorable mention in the competition. Except for 1929, the National Safety Competition of 1936 represented more man-hours of employment than any other year since the yearly contests began.

Jan 1, 1937

By J. W. Eckerd

This report describes an investigation of the technical feasibility of using a conventional commercial-size (10-ft. i.d.), rotating grate, dry-ash-removal type gas producer to make producer gas from chestnut-size bone anthracite. Test instruments were installed, and some minor changes were made in the equipment to handle the large quantities of materials expected. Extensive tests, lasting about 4 weeks, were planned, using 35 to 50 percent ash chestnut anthracite bone. However, operations were suspended after 8 days when it became apparent that to use this type of fuel satisfactorily substantial changes in equipment and operating procedures would be required. Nevertheless, enough data were obtained to indicate that gas could be produced continuously and routinely from bone coal in this type of producer whenever conditions justified the necessary development work.

Jan 1, 1960

By Charles B. Kenahan

The effects of ultrasonic radiation on the electrodeposition of copper-zinc, copper-cadmium, and copper-tin alloys from cyanide baths were investigated by the Bureau of Mines at frequencies of 18.5 and 38 kilocycles per second, and at acoustic intensities up to 0.5 watt per cm3. Significant changes occurred in the composition of the deposited alloys; some of these deposits were brighter, harder, more adherent, or of finer grain size than nonirradiated deposits. The irradiated deposits were also smoother and less porous, and they afforded better corrosion protection for the substrate metal in sodium chloride solution. The limiting current densities of the cyanide baths were increased by the application of ultrasonics. Anode and cathode current efficiencies also were increased, and cell voltages were lowered; the relationship of these effects to current density is discussed. Electrode potential measurements showed significant depolarization effects at both electrodes during ultrasonic irradiation. The resulting decrease in cell voltage was due chiefly to depolarization at the anode, and the anode became less passive.

Jan 1, 1967