Search Documents

By W. W. Krech, T. E. Perkins

As fractures are propagated through rocks, energy is absorbed near the extending crack tip. Apparent surface energies for several rocks have been measured by cleavage under dynamic con-ditions. At nominal crack velocities from 0.5 to 500 in (min, measurements showed that fractures propagated in discrete jumps. Calculated surface energies and moduli were relatively insensitive to nominal rate of cleavage. in another set of experiments, rocks were cleaved under high confining stresses. The rocks were submerged in low leak-off fluids which formed a filter cake on the freshly cleaved surfaces (similar to the hydraulic lracturing process). Apparent surface energies were increased substantially as the surrounding fluid pressure was increased. Moduli in bending increased significantly upon application of the first 1,000 psi but were insensitive to stress level at greater pressures. INTRODUCTION For almost 20 years, hydraulic fracturing processes have been utilized effectively to stimulate oil and gas wells. During this period, some process improvements have resulted from studies of fracture orientation, mechanics of fracturing, areas generated, conductivities of cracks, etc. Yet many questions remain concerning the conditions and pressures needed during fracture propagation. In this paper we will report additional studies of the mechanics of fracture extension. It was shown previously3 that large rock samples could be cleaved under controlled conditions so as to measure the apparent surface energy (that amount of energy absorbed per unit area of new surface created). In this paper we consider the effects of two additional factors on surface energies, viz.: (1) effect of cleavage rate and (2) effect of confining stress level. THEORY Cleavage experiments were conducted on rock samples similar to that illustrated in Fig. 1. Blocks of rock several inches wide, 2- to 3-in. thick, and up to 3 ft in length were grooved longitudinally with shallow guide slots. A crack was initiated and allowed to extend along the web as the top of the rock specimen was pulled (or pushed) apart. Auxiliary equipment permits the measurement of (1) force applied at the top, (2) separation at the top and (3) crack length. (Further experimental details will be given in the next section.) The rock beams created by the crack are considered ton be cantilever beams. The deflection (or separation of the rock beams) at any point is calculated 4,5 by the beam Eq. 1.

Jan 1, 1967

By S. Banisi, M. Pourkani, A. Kargar, D. Hamidi, M. Sarvi

"Flotation circuit of the Sarcheshmeh copper mine, which processes 40,000 t/d of ore at 0.9% Cu, consists of rougher, cleaning and recleaning stages. To study the stage recovery of copper, one of the eight identical flotation banks was selected for sampling. It was observed that 17% of copper goes to the tailings and the lowest copper recovery was for particles coarser than 105 microns. The third five-cell unit of this bank not only did not recover appreciable amount of copper but also decreased the concentrate grade. The grade of the last five cells was lower than the feed grade suggesting that mixing of the concentrates of the three units was not beneficial. To alleviate the problem, the concentrate of the first four-cell unit was directed to the cleaners feed box (i.e., by- passing the regrind mill). This increased the overall copper recovery by 1.7 %. Also rather than the current practice of adding the reagents only at the feed tank (i.e., 100-0-0%), various combinations of stage addition were examined. It was found that 75-25-0% addition regime could increase the total copper recovery by 1.3%. At the recleaning stage in order to increase the final copper concentrate grade, a froth washing system was used. To ease the maintenance of the system, a shower type washing system was installed. The optimum wash water superficial flowrate was found to be 0.06 cm/s. Continuos sampling of the recleaners with and without wash water over a period of two months showed an increase of 1.5% in the final copper concentrate grade at constant overall copper recovery.INTRODUCTIONThe Sarcheshmeh copper ore body that may rank as third or fourth largest in the world contains 1 billion tonnes averaging 0.9% copper and 0.035% molybdenum. It is located in southeastern Iran and has been processing 40 000 t/d of ore since 1982. The mine produces 100 000 tonnes of copper and 2200 tonnes of molybednite concentrate per year.After three stages of crushing, the ore with a F80 (80% passing size) of 12.7 mm is fed to eight parallel ball mills in closed circuit with cyclones to produce a product 70% finer than 75 microns. The concentrate of rougher flotation circuit is ground; rougher tails constitute the main component of the plant final tailings. A concentrate with an average grade of 31% Cu (chalcocite and chalcopyrite) is obtained after cleaning and re-cleaning stages. Total recovery of the plant varies between 83% and 87%, depending on operating conditions and ore type."

Jan 1, 2001

By David S. Yantek

Miners in underground coal mines experience prolonged exposure to high noise levels, often with A-weighted sound levels in excess of 90 dB. Field tests have shown that the continuous miner conveyor is a dominant noise source. This paper will identify the most significant noise-radiating surfaces on the continuous miner tail section using vibration levels and surface areas to estimate the sound power levels of each surface. In addition, using five test cases, this study will examine the effects of three engineering noise controls on the surface-averaged vibration levels and average sound levels measured with four microphones located two meters from the tail section. The noise-radiating surfaces of the conveyor’s tail section include the top and bottom decks, the sideboards, and the flex plates. Emphasis is placed on the changes in the estimated sound power levels in the 500 – 2500 Hz 1/3-octave bands since this frequency range accounts for 80-85% of the sound energy near the tail section. The results show that the bottom deck is the most significant noise radiator for the untreated miner. Installing a coated bottom deck reduces the estimated sound power level radiated from the bottom deck by 11 dB and the average sound level by 2 dB. Using a coated tail roller results in reductions of the estimated sound power levels for individual components from 1 to 4 dBand reduces the average sound level by 2 dB. Coating the slide plate has little effect on both the estimated radiated sound power levels and the average sound level. The test results indicate that modifications that reduce flex plate vibration and reduce energy transfer from the tail roller into the tail section will be effective in reducing noise when combined with a coated tail roller and coated return deck.

By P. C. Hodges

WHILE there is very little romance connected with the operation of a stone quarry, yet to those who have participated in the growth and development of a business that has been a pioneer in its field and that FIG. 1.-LOCATION OF PROPERTY OF MARBLE CLIFF QUARRIES COMPANY. has been in continual operation two-thirds of a century there is bound to be a background of experience, which if properly capitalized, brings progress as well as satisfaction in its accomplishment.

Jan 1, 1936

The spatial distribution of copper grades at the Mansa Mina project is highly variable due to the presence of high grade copper/silver/arsenic breccia bodies. Copper grades within the breccia bodies tend to average about 4.5% copper while grades in the surrounding stockwork average about 1.0%. The breccia is known to occur in the vicinity of significant controlling structures, however, the outline and therefore the thickness of the bodies are far from regular. Due to the high grade of these bodies a significant proportion of the value of the project is derived from the breccia tonnages. The irregularity in the outlines/thickness translates into an uncertainty in the breccia tonnage and therefore in the value of the project. Acknowledging the economic importance of the breccia bodies and the risk associated with the breccia tonnage uncertainty, significant additional drilling has been proposed to both understand the spatial distribution of the breccias and reduce project risk. The costs associated with this additional drilling are not inconsequential; thus, a reasonable question is ‘what value is derived from this additional drilling’? To obtain an answer to this important question, a simulation approach is applied. First the deposit is simulated using the existing drilling and the uncertainty in the resource is defined. Next the proposed drilling program is simulated and the simulated data are added to the existing data. Using this expanded data set a second simulation of the deposit is created and once again the uncertainty in the resource is defined. Using this approach, the reduction in the uncertainty in the resource can be determined. To convert this reduction in uncertainty (or reduction in risk) in the stated resource into a dollar value, a method of defining the increase in the project rate of return necessary to account for risk is presented. Using the two different rates of return, the difference in project NPV and hence the value of additional drilling is determined.

Jan 1, 2003

By J. F. Fiset, N. Bouzoubaâ, N. Reynier, C. Laviolette, Canadian Nuclear Laboratories

Canadian Nuclear Laboratories (CNL) is developing a disposal strategy for radioactive wastes, which contain significant amounts of uranium, cesium, and mercury. There are safety and economic incentives for the extraction of these elements before permanent storage in deep underground repositories. In addition, the actinide elements are also an important component in rare earth element (REE) ores and considered as impurities. Actinides separation from REE tailings is a significant concern in order to manage radioactive nuclides. Reprocessing mine wastes may present significant financial and environmental benefits. Experiments were carried out with radioactive cemented wastes (RCW) prepared at CanmetMINING. For all of the tested RCW batches, solubilisation yields are above 97% for Cs and 98% for U and Hg. Sulphuric acid leaching with potassium iodide improved the solubilisation of Hg by oxidation and formation of the tetraiodide complex (e.g. HgI4 2-, Kf = 2.1030). Cs and Hg were removed selectively by using potassium cobalt hexacyanoferrate (KCFC) and Lewatit TP214 ion-exchange resin respectively. U recovery using the chelating resin Lewatit TP260 was the most efficient. The presence of high iodine concentration improved the U uptake by the resin. The best U elution was obtained using 1 M Na2CO3, which resulted in 99% U recovery. U was then precipitated as sodium diuranate. A counter current effluent recirculation was performed successfully on RCW. The process was also applied to submerged tailings collected from two U mines and an REE ore. This paper presents an innovative process, using sulphuric acid and potassium iodide, for U, Cs, a

Jan 1, 2016

By Brian T. Burch, Paul N. Worsey

When fired, submerged Linear Shaped Charges (LSCs) lose all effectiveness in the cutting of steel. Users in underwater applications have reported having to substantially increase the charge size to the point where brute explosive force shears rather than cuts the target.

Jan 1, 2015

By A. Holeyman

The displacement compaction piles described in the paper are installed using a heavy casing or tube and an internal drop hammer. The casing which initially is closed at the bottom by a sand plug displaces the surrounding soil during the driving. Additional sand is rammed down through the casing during the extraction of the casing. The applications and limitations of the method are reviewed in the paper. The importance of checking the sand compaction piles during and after the installation is stressed. Indications of the compaction of the surrounding soil during the driving can be obtained by comparing the initial and the redriving logs of the casing as well as from the volume of sand added. A method to estimate the increase of the mean cone resistance as measured by CPT tests in sandy and silty soils is presented. The governing parameters are the volume of the added sand, the granulometric index and the initial cone resistance.

Jan 1, 2010

By Prasad S, Chatterjee S. S, Singh B. N

The chief source of metallic iron for steelmaking in India, even today, as it is in most part of the world, is through blast furnace (BF) route. This will continue to be so in the foreseeable future as the technology is most efficient, both process and economy-wise. However, as the world is moving into the next millennium, a critical look is being given to the process primarily because of its non-ecofriendliness (as a result of extensive use of metallurgical coal/coke requiring elaborate pollution control facilities) and huge investment involved for supporting facilities like extensive raw material preparation and handling, agglomeration, adoption of sophisticated instrumentation and control system, etc.

Jan 1, 1999

A physical modelling study has been carried out to simulate the slag-metal dispersion induced by a high-strength bottom gas injection. Water and kerosene were utilized to simulate metal and slag respectively. A water model of CLU (Creusot-Loire Uddeholm)vessel was used with three different nozzle orientations, namely, off-centre, triangular off-centre and centre. The gas flow rates changed from 0.00599 m3/s to 0.01081 m3/s. Height of heavy and light phases was kept fixed at 0.23 m and 0.02 m respectively. The dispersed phase hold-up was determined at various axial and radial distances, gas flow rates, and tuyere configurations. The observations revealed that at a fixed gas injection rate, as the vertical distance increased in the centerline, straight off-centre orientation resulted in greater dispersed phase hold-up values than those of the centre configuration and the triangular off-centre orientation. The dispersed phase hold-up was found to increase with gas injection rate and decreased with axial distance. The variation of the dispersed phase hold-up with the dimensionless axial distance and the gas injection rate was correlated by using the modified Froude number. The experimental values of the dispersed phase hold-up were found to be in reasonable agreement with the correlated values obtained from the modelling equations. The findings of the present study may be utilized in the ferroalloy refining vessels in terms of designing tuyere locations for optimum processing conditions.

Jan 1, 2004

Of late there have been various papers published on this subject by various authorities, in which certain definite factors influencing slime settlement have been brought forward. As the principles set forth by these writers are of great interest, and have, in most cases, been generally accepted, the author will review them in the hope that by discussion some more knowledge may be brought to bear on many points connected with the subject.The definition of slime at the present time is not a standard one, and varies according to different authorities, some defining slime as ore crushed to such a fineness that it will pass through a screen of standard size, say 150 or 200-mesh, in water (1, 2);others as that part of the finely-crushed material which is in the physical condition which causes it to remain in. suspension in water, and possesses pr?perties which render it almost unleachable (3). Authorities seem divided on this point, but of late American writers seem to prefer the former definition. On the contrary, B L Gardiner describes slime as a mixture of small particles of crushed ore of varying sizes which, when mixed with water, tend...

Jan 1, 1912

By Abolfazl Eslami, Sara Heidarie Golafzani

CPT-based methods considered as complementary tools for static analyses outperform other axial pile bearing capacity predictive methods. Considering soil spatial variability and minor errors associated with procedure and operator, CPT-base methods mitigate the effect of latent uncertainties in pile design. These methods were developed based on different databases and purposes. Hence, several statistical and probabilistic attributes were defined and implemented to assess the predictive CPT-based methods’ performance via CPT and pile databases in terms of the model parameter. These features make a comparison among methods in terms of precision, accuracy, and efficiency. Furthermore, CPT-based methods can be subjected to scrutiny over their backgrounds and how they were developed via reliability analysis. In this regard, a database of sixty-two driven piles and their adjacent CPT soundings were gathered, and six commonly applied CPT-based methods were examined according to criteria other than prevailing statistical and probabilistic ones, including; (a) input variables, (b) soil behavior classification (SBC) (c) model assumption (d) Influence zone, and (e) axial loading direction. According to these introduced criteria, CPTbased methods were classified and appraised via efficiency ratio. Eventually, these reliability-based, statistical, and probabilistic criteria evaluate the understudied methods performance for the investigated compiled database and help designers select consciously appropriate predictive methods according to the site conditions.

Sep 8, 2021

By George Mylonakis

The curvatures and subsequent bending imposed to piles by the surrounding soil during the passage of strong seismic waves is studied. This type of bending develops even in the absence of a superstructure and is referred to as "kinematic bending", to distinguish it from bending imposed to piles by loads generated from the inertia of the superstructure ("inertial bending"). Although kinematic loading may be severe in the presence of sharp stiffness discontinuities in the profile and may lead to damage, it has received little attention by engineers. The scope of the paper is twofold: (i) to discuss some fundamental aspects of seismic pile bending, and (ii) to review some existing design methods. To this end, a dimensionless bending strain parameter (instead of the more commonly used bending moment), and a strain transmissibility function relating pile bending strain and corresponding soil shear strain are introduced. Numerical examples are also presented.

Jan 1, 2002

By Alex C. Smith, Thomas A. Gray, Lynn M. Crayne, Michael A. Trevits, Phil Glogowski

Mine fires constitute one of the greatest threats to the health and safety of those working in the underground environment and each event has the potential for disastrous consequences. Of the major mine fires and thermal events that have occurred in the United States in the last 6 years, it is estimated that remotely installed seals could have been used in 63% of the events to control fire growth or to aid in fire suppression work. The National Institute for Occupational Safety and Health (NIOSH) is conducting full-scale tests at the NIOSH Lake Lynn Experimental Mine to evaluate and improve remote mine seal construction technology. The main focus of this work is to develop reliable technology that will completely close the mine opening from floor-to-roof and rib-to-rib. This paper presents the results of remote seal installations using grout-based materials.

By Stephen C. Tadolini, Peter (Yunqing) Zhang

A unique circumstance created by monitoring a pre-driven longwall recovery room permitted measuring the stresses of a coal pillar throughout its entire life cycle in less than a week. A fender pillar, created in approximately the middle of a longwall panel at a depth of 650 ft, transformed from a solid barrier pillar - to a yielding pillar - to a residual pillar as 3 ft slices were methodically removed with the longwall shearer. The complete transformation, or life cycle, took place in less than 12 hours. The stresses were quickly transferred from the pillar onto the standing pumpable concrete supports and into the outby pillars. Roof to floor closure measurements, combined with the timing of the pillar behavior, provides a detailed look at the uncontrollable convergence of underground mine openings. Pillars remain the most important form of “primary support” and understanding these life cycles is vital for safe and efficient mine design, in both room and pillar and longwall panel extractions.

By S. M. Rupprecht

"SynopsisThis paper is intended to document recent personal thoughts, opinions, and debate around the South African Code for the Reporting of Exploration Results, Mineral Resources and Mineral Reserves (the SAMREC Code) (2009) and its current usage by Competent Persons. Admittedly, some debates are as old as the SAMREC Code itself and have been ‘parked’ as no consensus could be reached by members of the SAMREC Working Group.Some of the more critical issues currently under examination are the definition of Competent Person and the potential registration of Competent Persons, the current re-write of the Code, and the introduction of reporting of Exploration Results, Mineral Resources, and Mineral Reserves on an ‘If not – why not’ basis, noncompliance with the Code and discipline, the role of the Johannesburg Stock Exchange Readers Panel, and the valuation of mineral assets based on scoping studies.IntroductionThis paper is intended as a personal memoir of recent thoughts and debate around the South African Code for the Reporting of Exploration Results, Mineral Resources and Mineral Reserves (the SAMREC Code) (2009) (‘the Code’). Admittedly, some debates, such as reporting of Mineral Reserves inclusive or exclusive of the Mineral Resource, are as old as the SAMREC Code itself and have been ‘parked’ as no consensus could be reached by members of the South African Mineral Resource Committee (SAMREC) Working Group. The author, who has been involved with the SAMREC Working Group since 2007, offers observations in his personal capacity as a professional mining engineer with the intent of getting practitioners to contemplate the influence of the Code on the mineral industry. Current practices in the compilation and reporting of Exploration Results, Mineral Resources, and Mineral Reserves are often deficient in adhering to the Code and a conscious effort must be made by the mining sector to improve the standard of public reporting, in particular Competent Person Reports (CPRs) and Public Reports issued by listed mineral exploration and mining companies."

Jan 1, 2015

By G. R. Lane

A large opencast gold mining company in Africa had just completed a feasibility study for an expansion of the operations. A traditional net present value project valuation methodology had been used that showed a very positive net present value (NPV). The project team had conducted a qualitative risk assessment that identified and logged all potential project risks and had subjectively incorporated 'risk' via the discount rate and other assumption contingencies around gold price expectations, operating parameters, etc. Management requested that an independent quantitative risk modelling approach be adopted to obtain a better understanding of the impact of risk on the overall project valuation and confidence level in the final valuation. A detailed project valuation model was configured in the Cyest Carbon Modelling Technology platform, and the stochastic modelling module used to perform the Monte Carlo simulations. Analysis of historical operational performance data relating to actual achievements versus planned and budget determined the historical variability of the underlying parameters as well as variance to budget. This was done at a detailed level for mining rates and costs, processing rate, costs and recovery, and other operational efficiency measures. External market assumptions relating to gold price, exchange rate, and inflation were modelled and the dependency between them modelled using a copula. This case study will demonstrate the approach taken to building and populating the quantitative risk model and the overall results of the Monte Carlo simulation. The final valuation demonstrated that the project had a 44 percent probability of an NPV less than zero i.e. a 44 percent chance of project finance loss.

Jan 1, 2013

By G. A. Craig

The Moon, asteroids, and planets of the solar system represent the most distant caches of wealth that humanity has ever considered recovering. Yet, in addition to the potentially recoverable values represented there, harvesting off-Earth resources has a second, almost incalculable sustainable benefit in that they can be retrieved with absolutely no damage to Earth. Previous research mostly assessed the potential of asteroids and the Moon for mining purposes from a theoretical and scientific point of view. These studies investigated drawbacks that could be experienced in this type of operation, but no detailed economic evaluation that is meaningful for mining project management has been conducted and the parameters that are most likely to make an operation feasible are unknown. This paper provides a preliminary economic and sensitivity analysis of a possible off-Earth mining business extracting minerals from an existing asteroid.

Jan 1, 2014

By J. C. Vreugdenburg, B. A. Dippenaar, J. Muller, T. L. de Vries

Iron ore fines are agglomerated to produce sinter, which is an important feed material for blast furnaces worldwide. A model of the iron ore sintering process has been developed with the objective of being representative of the sinter pot test, the standard laboratory process in which the behaviour of specific sinter feed mixtures is evaluated. The model aims to predict sinter quality, including chemical quality and physical strength, as well as key sinter process performance parameters such as production rate and fuel consumption rate. The model uses the finite difference method (FDM) to solve heat and mass distributions within the sinter pot over the height and time dimensions. This model can further be used for establishing empirical relationships between modelled parameters and measured sinter properties. Inputs into the model include the feed material physical properties, chemical compositions, and boundary conditions. Submodels describe relationships between applied pressure differential and gas flow rate through the bed of granulated fine ore particles, combustion of carbonaceous material, calcination of fluxes, evaporation and condensation of water, and melting and solidification. The model was applied to typical sinter test conditions to illustrate the results predicted, and to test sensitivities to parameters such as feed void fraction, feed coke percentage, and the fraction of combustion heat transferred to the gas phase. A model validation and improvement study should follow, ensuring sinter test results are free from experimental errors by conducting repeated tests.

Jan 1, 2015

By C. O. Aksoy

There is a long history of coal production in Turkey with electric energy generated from power plants since the 1950s. However, the cost of power generation is high. Therefore, it has become necessary to find a means of decreasing production costs to become more competitive in a global market. This paper attempts to economically minimize the overall operating costs of a dragline-shovel-truck system applied at an open pit mine that has fed the Yatagan power plant since 1979, lowering the lignite production cost, and indirectly, the overall electricity generation unit cost. Systems currently in place, as a result of former optimization studies, are time-consuming and expensive to re-implement to comply with today’s very different geometric and economic conditions affecting mining operations. In such cases, rather than re-optimization, it is more viable to identify the parameters that affect the minimum unit cost, via a cost minimization study, allowing present mine equipment to be utilized more efficiently. Unit cost minimization analyses are subject to the capacity of the pool of mining equipment available, combined with the mining block geometry from pre-stripping onwards. In this overall unit cost minimization study, P&H shovels and CAT 777 trucks with capacities of 15 yd3 and 77 tons, respectively, were used in truck-shovel pre-stripping operations. A 65 yd3 Marion 8050 dragline was used to expose the overburden immediately over the coal seam. Pre-stripping bench heights varied from 8 m to 20 m and dragline bench heights from 20 m and 25 m were evaluated to minimize the unit cost of field operations. Total overburden extended to a depth of 60 m (35 m to 40 m for pre-stripping). Minimization analyses performed on the pre-stripping truck-shovel operation, prior to dragline operations, determined that the shovel bench height should be 15 m requiring a dragline bench height of 25 m.

Jan 1, 2005