Search Documents

By Gerald Verbeek, Erick Baziw

"Downhole Seismic Testing (DST) is an important geotechnical testing technique for site characterization as it provides low strain (<10-5) in-situ interval compression (Vp) and shear (Vs) wave velocity estimates. These velocities are determined by obtaining relative arrival times of source waves as they travel through the stratigraphy and are recorded by one or more vertically offset seismic sensors. A challenging aspect of this process is to characterize the seismic data sets to determine the analysis method that will result in the most accurate interval velocity values. This paper introduces an assessment technique which utilizes linearity estimates (i.e., hodograms fitting straight lines) from the polarization analysis in conjunction with crosscorrelation coefficient calculations of the full waveforms as well as the deviation of the source wave frequency spectrum from a desirable bell-shaped curve. The paper will provide an overview of the technique and include some examples of actual data sets where the technique was applied to analyze those data sets.1. INTRODUCTIONIn general terms, Downhole Seismic Testing (DST) such as Seismic Cone Penetration Testing (SCPT) is a geotechnical technique for measuring in-situ shear and compression wave velocities (VS and VP respectively). The main goal in DST is to obtain arrival times as the source wave travels through the soil profile of interest, and from these arrival times the velocities are then calculated. Figure 1 shows a schematic of the typical DST configuration: a seismic source is used to generate a seismic wave train at the ground surface. One or more downhole seismic receivers are used to record the seismic wave train at predefined depth increments. The downhole receiver(s) may be positioned at selected test depths in a borehole or advanced as part of an instrumentation package as in the case of SCPT. When triggered by the seismic source a data recording system records the response of the downhole receiver(s)."

Jan 1, 2017

By W. Hodge Caraway

This report presents the results of an evaluation of several indirect methods of measuring the water content of oil-reservoir rocks. The water content of oil-base cores is considered to be most nearly representative of the water content of the undisturbed petroleum reservoir and therefore, the direct method of measuring the volumes of water in cores cut in oil-base drilling fluid was adopted as a standard for comparison. The indirect methods evaluated included (1) displacement through a semipermeable membrane by air, (2) centrifuge, (3) evaporation, (4) mercury injection, (5) chloride dilution and (6) electric logs. Approximately 270 samples of cores from petroleum-reservoir rocks were used in the study. The cores, most of which were cut with oil-base mud in the hole, were taken from oilfields in California, Texas Gulf coast, Colorado, Oklahoma, and Alaska.

Jan 1, 1959

By Bo Westerberg, Mattias Andersson, Yvonne Rogbeck

"Deep stabilisation has been used in Sweden for decades. The method has been improved to allow it to be used in different types of soils and with new binders. One challenging soil type in Sweden is so-called sulphide soil, a fine-grained soil which contains organic material and iron sulphides. There have been some cases in Sweden of problems when using deep stabilisation in this type of soil, and in one case a slope failure occurred. This paper shows that it is possible to achieve good results with deep stabilisation in sulphide soils. Laboratory and field studies from a test site along the Botniabanan railway line in Sweden are presented. Geotechnical and chemical properties of the natural soil were investigated in the laboratory and one or more of these properties may explain the differences in the stabilising effect of sulphide soils. The strength of the laboratory samples and the columns in the field were tested and compared. It is shown that a satisfactory stabilisation effect can be achieved with the proper choice of binder, amount of binder added, curing time and mixing energy. In sulphide soils, more binder additive is needed than in “ordinary” inorganic clays.1. INTRODUCTIONThe term sulphide soils is used in this paper to refer to the unique types of sulphide soil commonly found in the coastal areas along the north-eastern coastline of Sweden between the cities of Gävle and Haparanda, a distance of about 900 km. Sulphide soils are in general very compressible, susceptible to creep deformation and normally show low undrained shear strength. A sulphide soil may have a negative environmental impact through acidification and chemical action if it is subjected to oxygen, for example during excavation or lowering of the ground water table, Mácsik (1999). In foundation engineering works, efforts are made, for environmental or/and economic reasons, to use the sulphide soil as the foundation instead of excavating it. Deep stabilisation by means of columns is a potential method for use when sulphide soil needs to be improved in order to reduce settlements or/and increase the stability of embankments.Sulphide soils were formed as sediments at river mouths and off the coast in the special environment prevailing at the time of sedimentation, Mácsik (1994). The water in which the sulphide soil was sedimented was brackish/sweet and the environment was typically deficient in oxygen. The environment prevented complete decomposition of the organic material in the sediments. As a result, sulphide soils were formed primarily in the form of a fine-grained composition of clay and silt minerals, iron sulphides and organic matter. Such environments still exist today and new sulphide soil sediments continue to be formed."

Jan 1, 2015

By Kilian Neubert, Hermann Wotruba, Henning Knapp

Sensor-based sorting has been integrated into more and more applications in mineral processing over the past decades. Various sensor types, such as line scan cameras, near infrared sensors and X-ray transmission sensors, allow the separation of a vast variety of raw materials. Sensor-based sorting has several economic benefits which can make the difference between an uneconomic operation and a profitable mine. Sensor-based sorters can be applied to fulfill various sorting tasks, such as waste rejection, product quality improvement and ore type diversion, and have a significant impact on the layout of the processing plant. Therefore, it is important to include sensor-based sorting into the planning of a processing plant at an early stage. To evaluate the applicability of sensor-based sorting for any specific ore type, it is currently necessary to provide several hundred kilograms of material for subsequent bulk tests. In exploration, ore samples are usually rare and only available in form of drill cores. The acquisition of drill cores is time-consuming and expensive especially for deposits in great depth. Hence, it is unfavorable to spoil valuable drill cores for bulk tests. This paper describes a methodology to evaluate the applicability of sensor-based sorting based on drill core analysis. That methodology offers the possibility to calculate the achievable performances of different sensor types for various grain sizes without comminution of drill cores. The general methodology is shown on basis of an exemplary test work on drill cores from a currently conducted exploration.

Jan 1, 2014

By V. E. Edlund

Pyrometallurgical studies by the Bureau of Mines demonstrated the feasibllity of sintering and smelting a low-grade flotation concentrate made by pilot-plant processing 10-percent manganese ore from the Maggie Canyon deposit, Mohave County, Ariz. Under optimum conditions 85 percent of the manganese in a flotation concentrate that assayed 36 percent manganese was recovered as standard ferromanganese. A blend of this flotation concentrate with high-grade dithionate pilot plant precipitate was similarly processed with a recovery of 90 percent of the manganese. Thorough mixing and pelletizing of the charge before treatment on the sinter hearth was necessary to produce a well agglomerated product by single pass sintering. Although satisfactory sinter was produced from a variety of material combinations, best results were obtained on a charge that contained 80 percent flotation concentrate and 20 percent return sinter fines. This combination was mixed with 6 percent coke, based on weight of concentrate; and 12 percent moisture. Sintering such a charge yielded a well agglomerated product containing over 80 percent coarse material, The results of standard crushing tests showed that the product was physically comparable to iron ore sinters and manganese nodules.

Jan 1, 1962

Analysis of Procedures and Drivers for Industrial Waste Management

Sep 13, 2010

By Bryan Ulrich

On March 15, 2012, about 24 attendees from several western states attended Roundtable 2012, hosted by Knight Piésold and Co. at the Red Lion Hotel and Casino in Elko, NV. The focus of this year?s discussion was ?Acid Rock Drainage for Engineers and Environmental Scientists.? Other names may have been more suitable for the event, perhaps combining geochemistry, with air and water quality and their long-term effects on soil and rock mechanics. Bryan Ulrich (senior vice president, Knight Piésold?s Nevada operations) and Steve Lange (senior geochemist, Knight Piésold, Denver, CO), helped facilitate the discussion. Attendees included personnel from a dozen mining properties, various corporate offices and academia. There were also attendees from a geochemical testing laboratory to help respond to specific questions pertaining to testing protocol and procedures.

Jan 1, 2012

By Hongpu Kang

The fully mechanized top coal caving mining method has been the main mining approach for thick coal seams with high output and efficiency in Chinese coal mines. The gateroads for the top coal caving mining faces should be driven along the floor of the thick coal seam with a part of the seam as roof. The support of the gateroads is commonly difficult because of the low strength and broken structures of the coal seams, and the increasingly large section of gateroads meeting the need of greater and greater face coal output. Based on the analyses on the geomechanics properties and production conditions of the top coal caving mining, the influences of the top coal caving mining parameters on the stability of gateroads, including mining thickness and face length, are studied. The deformation and damage features of the rock mass surrounding the gateroads with the top coal seam as roof are investigated, the interaction of the support with the surrounding rock mass, the support theory are studied. The bolting design method and criteria, bolting forms and parameters for the gateroads with the top coal as roof are put forward. The rock bolting components, including bolt bars, face plates, cable tendons, meshes, and steel straps, are introduced. Finally, the gateroad bolting effects are evaluated through a typical case study on the basis of field monitoring data, such as the displacement of surrounding rock mass and the forces along bolts and cables.

Aug 1, 2013

By L. E. Djingheuzian

"ForewordTHE FOLLOWING excerpt is taken from Fine Grinding Investigations at Lake Shore Mines (C.I.M., Trans., Vol. XLIII, 1940, p. 307):""MacCalman, who has carried out exhaustive testing on the accuracy of screen analysis, makes the following statement in his report, The Accuracy of Sieving Tests, Industrial Chemistry (London, England), Vol. XIV, p. 231:"" 'It will be shown that, as no specific relationship between the sieving value and the various dimensional features of the sieve is evident, though there is an apparent tendency for the sieving value to follow the average aperture size, it is apparently impossible to define the sieving value of a screen from dimensions alone, and the calibration of sieves for important tests on a specific material, whereby the sieving values of these sieves are related to that of an arbitrarily chosen master sieve by correction values, will be recommended."" 'It will be emphasized that these correction values are probably not applicable to other materials, or the same material of different size composition. Sieve users, for important tests or in cases of dispute, will be recommended to calibrate their sieves against a mutually acceptable standard with specified conditions of test, and to recalibrate at intervals' ""."

Jan 1, 1953

D EC. 20-The spirit of Christmas and good will toward men has managed a few brief appearances on the front pages, welcome relief from man&apos;s usual ill-will toward man. A couple politicos did their best to brighten the scene by well-publicized romances. There was a general exodus to Florida to patch up nervous systems, and even the UNO quieted down as Mr. Vyshinsky departed for home via Eastern Germany. Before going he opened up a preliminary bombardment for the worldwide "communist peace offensive," and it is now the duty of the 600 million (according to the Cominform) ideological converts to press home the attack. In Washington, Mr. Lilienthal resigned as Chairman of the Atomic Energy Commission and demonstrated again the difficulty of government to retain the services of capable men. The President has yet to appoint another victim- possibly someone nicely noncontroversial and timid. So might the critics be appeased, but it would bode ill for the rapid exploitation of peaceful uses of atomic energy, the relaxation of excessive secrecy, wider sharing of developmental work with friendly nations and possible revision of the Acheson-Lilienthal proposals for inter- national control of the atomic bomb.

Jan 1, 1950

By Robin Belley

Outline Introduction Wabush Mines HistoricalBackground Mine and Concentrator at WabushMines High Intensity Magnetic Separators (HIMS) Development of the Manganese Removal Process Pilot Plant Testing Phase Manganese Removal Line 1 Coming Phase: Manganese Removal Line 2 Manganese Concentration Process Development Historical Background 1847: Creation of the Cleveland Iron Company1850: Opening of its first iron ore mine in the Upper Peninsula of Michigan 1965: Beginning of Wabush Mines at Scully Mines, Wabush, Labrador. 1980-1990: Questions raised about how to exploit Scully high Mn Ore (> 2%)Part of the available ore is not saleable due to too high a level of pyrolusite (MnO2) Adding this ore to the resources would be valuable (longer mine life and lower stripping ratio) 1990s: Testwork for Manganese removal Many different processes are studied over more than a decade High Intensity Magnetic Separators (HIMS) are identified as the best technology for Mn removal 2007: Pilot Mn removal line installed Testing carried out through 2007-2008 First Production Line is ordered (2008) 2009: Cleveland Cliffs (now Cliffs Natural Resources)acquire the remaining part of Wabush Mines 2010: Mn Removal Line 1 construction & commissioning Summer 2011: Mn Line 2 Construction

May 1, 2011

By Lang Shiping

The criteria for designing a crushing chamber are presented and a program for designing the shape of the chamber is proposed. During the chamber shape design, major design parameters are analyzed first, optimized parameters are determined next and the basic shape of chamber is figured out finally. In the basic chamber design program, the influence of abrasion of basic chamber shape and material characteristic are not accounted for usually. Here, based on the minimum abrasion of chamber shape and uniform particle size theory, the equation for chamber surface curve and the transcending function were formulated and a low-abrasion chamber was designed. Since the chamber shape designed based on experience and experiments is not necessarily the best, optimal design of the crushing chamber shape was carried out. Cubic spline function was used to represent the chamber shape curve and a mathematical model was formulated. The optimal shape solution was obtained using a complex method. Finally, the optimal chamber shape was determined by matching the moving cone stroke S, moving cone speed N and the moving cone bottom angle Thus, superior technical performance of the cone chamber was achieved.

Sep 1, 2012

By V. Ferrari

This report documents the three-phase program to design, fabricate, test, and demonstrate economical and practical methods of reducing noise levels on underground coal mining portal buses (mantrip vehicles). The noise-control treatments applied to a production-model portal bus were as follows: ? Wheel/rail vibrations were isolated from the vehicle frame by inserting elastomeric materials between suspension components. ? Vibration-induced noise was reduced by replacing all large sheet metal panels (except floor plates) with damped steel panels. ? Motor noise was reduced by tight-fitting covers made from damped steel and lined with sound-absorbing material, and by elastomeric motor mounts. ? The standard spur gears used in the traction drive system were replaced with helical gearsets. The program achieved the goal of reducing the average sound-level to below 85 dBA for typical operating conditions.

Jan 1, 1981

Amongst representative men directing alluvial mining of erations in Victoria, some difference of opinion exists as to the best system of working the deep leads. The developmental operations of shaft-sinding, extending a reef drive, partially watering and rising up into the wash dirt are practically the same on all fields but subsequent mining is continued either on the Chiltern and Rulberglen or Ballarat systems, the latter being referred to by the Chiltern and Rutherglen miners as the &quot;down country&quot; system. In the former, the leading wash and cross drives are lept from 300 to 500 feet ahead of the reef drive, and in the latter the reverse method keeping the reef drive well ahead of all wash workingsis adopted.In the majority of alluvial mines in the southern and western fields, the initial work of defining the course of the lead is costly, owing to the thick superincumbent layers of hard basalt, to bore which costs from 9/- to 15/&#183; per foot. Unfortunately large sums of money have been wasted in this work, owing to a want of care and knowledge in the selection of bore sites, and improper recording of the strata pierced, thus handicapping alluvial mining and bringing boring operations...

Jan 1, 1902

By Hugh R. Wilson

Echo Bay&apos;s Waste Management Program for its Lupin Mine was developed in response to the terms and conditions of the water license issued to the mine in 1981 by the Northwest Territories Water Board. The gold mine, located about 80 km (50 miles) south of the Arctic Circle, commenced production in 1982. The Waste Management Program was based originally on the total containment concept, contingent on future treatability testwork results indicating the best treatment method to ensure pond discharges would be in compliance with stated Northwest Territories Water Board discharge criteria. To assess the various treatment technologies, an investigative program was established to determine the most effective means for treating the tailings pond water. In the course of milling, about 850,000 m3 (11 million cu yd) of tailings are produced annually that require appropriate management to protect the environment. This annual tailings stream consists of about 175,000 m3 (229,000 cu yd) of solids and 675,000 m3 (883,500 cu yd) of water. Following the completion of the required waste management studies, a two-ponds-in-series concept of tailings impoundment was developed. To attain this concept, the tailings impoundment area would require modification and construction to enable the use of such a system.

Jan 1, 1991

By E. Emami, J. Valencia, J. Sattarvand

The knowledge of the final location of a drillhole is critical in obtaining the expected blasting results. This paper proposes a new methodology to control the drilling accuracy in open-pit mines using aerial images and machine learning. Specifically, it investigates how support vector machines (SVM) and convolutional neural networks (CNN) are useful for automatically detecting blastholes over drone images captured in blasting patterns. Several datasets were obtained from different mines in Nevada (USA) and were used to train and test models. We then processed those images to create orthomosaic and digital elevation representations of the patterns. Thousands of patches were then extracted and augmented to develop SVM and CNN models. The results demonstrate that machine learning is useful for drillhole detection and, in this way, to control the drilling accuracy and use the explosive energy more efficiently.

Sep 1, 2021

Stawell Gold Mines Pty Ltd operates two underground decline mines within the township of Stawell. An active exploration program and commitment by owners to improving the ore reserves has led to an improved mine life and reduced operating costs since the purchase of the operation by Mining Project Investors and Pittston Mineral Ventures in late-1992. Over the past six years of operation a cumulative 1 150 000 ounces of gold have been added to the mineral inventory. An improved geological understanding of the orebody has evolved over time increasing the ore reserves and allowing the development of long-term plans for the mines future. This has enabled important capital decisions to be made providing the impetus for improved productivity and thereby reduced operating costs. Co-operative mine planning and mine geology utilising best practice geological systems have enabled the effective extraction of a structurally complex and mineralogically varied deposit within a rural Victorian township. Detailed metallurgical research has improved the function of an aged and poorly designed circuit to boost the mill capacity whilst also improving the metallurgical recovery. The combination of metallurgical expertise and an understanding of the geological setting enable an effective control of metallurgical recovery.

Jan 1, 2000

By J. P. Bennett

The Bureau of Mines is investigating the acid resistance of ceramic materials to identify construction materials for emerging technology in chemical and metallurgical processes. Eight commercial ceramic materials, including two red shale, two fireclay, a silica, a silicon carbide, a carbon, and a high-alumina brick, were evaluated. Samples were exposed to 40 wt pct HN03 at 70° and 90° C and 60 wt pct HN03 at 50°, 70°, and 90° C for time periods of 110 days. Statistically significant changes in cold crushing strength were generally small or not detected, except for a strength drop in the high-alumina brick, which decreased in strength when exposed to the chosen acid concentrations at 90° C. Vol-ume and weight changes were also measured. The leach rates of Al, Ca, Fe, K, Mg, Na, Si, and Ti were monitored. Increasing temperature or a decrease in the acid concentration resulted in an increased ion leach rate. Of the conditions tested, the most severe corrosion occurred at 90° C for a 40-wt-pct-HN03 solution. The silica brick had the best overall acid-resistant properties, followed by a red shale and a fire-clay brick. The carbon and silicon carbide bricks are not recommended for service.

Jan 1, 1984

By Mostafa Maazouz, Jeff Blackwood, Mauricio Gordillo, Sang Hoon Lee, Micah Ledoux, Liang Zhang

To meet rising requirements for the low-damage ultra-fine process with the focused ion beam (FIB) in the materials science and semiconductor industry, the advanced ion column and corresponding advanced applications as a solution are developed and demonstrated. Novel high-speed high kV milling, low kV cleaning and imaging capabilities have enabled the creation of impeccable ultra-thin structures such as TEM samples and nanometer scale structures. Minimizing Ga+ induced sample damage is achieved through the optimized final cleaning at 500 eV ion landing energy with the new ion optics, which utilizes close control of the ion dose, beam incidence angle, spot size, pattern algorithm and imaging performance. Newly introduced process solutions achieve the improved process throughput. Initial demonstration is performed on the latest 14 and 10 nm scale FinFET device. Validation of the thinnest <0.8 nm thick ion damage layer on the <7 nm thick lamella structure was confirmed through TEM analysis.

Mar 1, 2017

By Tom Barczak, Julian Restrepo, Zach Agioutantis

"The Alpha Foundation for the Improvement of Mine Safety and Health, Inc. (Foundation) was established as part of a Non-Prosecution Agreement (Agreement) entered in December 2011 by the United States Attorney's Office for the Southern District of West Virginia, the United States Department of Justice and Alpha Natural Resources, Inc. (""Alpha"") and Alpha Appalachia Holdings, Inc. This Agreement was related to the explosion at Upper Big Branch Mine, an underground coal mine owned by Performance Coal Company, a former affiliate of Massey Energy Company, which Alpha acquired in June 2011. Pursuant to that agreement, Alpha agreed to establish a trust to fund projects designed to improve mine health and safety by providing $48,000,000 into the trust. The mission and vision of the Foundation are as follows:Mission: To improve mine health and safety through funding research and development projects by qualified academic institutions and other not-for-profit organizations.Vision: To enable miners in the future to be free of work-related injury or disease by the implementation of the results of the projects funded by the Foundation and undertaken by the best researchers from any discipline that can contribute.The focus of the research effort is not limited to coal mine explosion prevention, and in fact encompasses the entire spectrum of health and safety, addressing issues in both underground and surface mining operations in all mining sectors. Four major focus areas are identified (see Figure 1): 1) Health and Safety Interventions; 2) Mine Escape, Rescue, and Training; 3) Safety and Health Management and Training; and 4) Injury and Disease Exposure and Risk Factors.The Foundation is seeking to expand the knowledge base of mining safety and health information that can lead to resolving complex mining problems. To that end, the projects funded by this effort are designed to provide a spectrum of knowledge potentially encompassing the following:• Surveillance data - Collect and analyze surveillance data that better documents the prevalence and trends of occupational safety and health across the mining industry."

Jan 1, 2016