Search Documents

By V. F. Parry, J. B. Goodman, W. S. Landers

"This investigation was conducted: under the direction of A.C. Fieldner, chief, Fuel and Explosives Branch, Bureau of Mines, Washington, D. C. The following members of a Technical .advisory Committee were helpful in advancing the investigation: L. C. Harrington, dean, College of Engineering, University of North Dakota; D. F. Pane, president, Sheridan-Wyoming Coal Co.; Carson W. Smith, president, Consolidated goal & Coke Co.; Durbin van Law, consulting, engineer, Denver & Rio Grande Western Railroad; and C. B. Carpenter, professor of metallurgy, Colorado School of Mines. Coal samples from the Northern Colorado field used in the stoker during 3 years of service were supplied through the cooperation of N. C. Brooks, secretary, Northern Colorado Coals, Inc.This report describes the development and practical tests made on a small stoker-fired system for heating service water automatically. The system was designed to take advantage of the favorable reactivity of low-rank fuels, and the objective was to devise a combination of stoker, heat-receiving, and hot-water storage system Which would be automatic for at least 30 days without attention, while heating service water at minimum cost. The system was developed to a point where coal consumption was less than 10 pounds (or less than 100,000 B.t.u.) per day. The total operating cost of hot water for an average-family-was about $1.00 per month, with coal retailing at $6.00 per ton and electric power at 4 cents a kilowatt-hour. The heating system was designed for the utilization of low-rank fuels, but the general features of the double-tank system can be 'employed fuels, either gas or liquid fuels.The Subbituminous Coal and Lignite Section of the Bureau of Mines began investigations on the utilization of low-rank fuels in domestic appliances during 1939. Tests were made on various devices to find out if they were suitable for the low-rank fuels. Most of the available appliances for burning coal have been designed for the higher-rank fuels, and they are not well-suited for burning the lower-rank coals at maximum efficiency, because subbituminous coals and lignite have high bed moisture ranging between 20 and 40 percent by weight, which lowers heating value to the range of 10,000 to 6,500 B.t.u. per pound. They are noncoking, and the ash content ranges between 4 and 6 percent, with a fusion temperature of about 2,0000 F."

Jun 1, 1946

By F. J. Sotillo

The objective of this investigation was to determine the feasibility of using a high-pressure roll mill (HPRM) to improve the separation efficiency of dolomite from apatite in downstream operations when treating high-dolomitic pebbles. High-dolomite samples from four phosphate mines were used for the test program. The research work plan included sample characterization studies; INSTRON tests to develop preliminary crushing data; high-pressure roll mill evaluations to determine crushing parameters, such as feed rates, rolls speed and gap, and applied torque, pressure and energy; and screen, microscopy, and flotation studies to assess dolomitelapatite separation efficiency. The results of the HPRM tests show that commercial products for all four mines can be obtained. Recoveries of 74-82% of the P2O5 and rejections of 46-83% of the MgO were reported with an specific energy consumption of 0.2-0.5 of that of a laboratory rod mill.

Jan 1, 1998

By R. Addison, T. Swendseid, R. Kehmeier, D. Larsen, J. Uhrie

"The development of a mining project necessarily progresses through many steps, beginning with the identification of a mineral resource and continuing through project construction. Several classifications of engineering study development are described, including preliminary economic assessment (PEA) or scoping studies, prefeasibility studies (PFS), feasibility studies (FS) and regulatory codes, each with a specific project organizational objective. This paper addresses the PEA, PFS and FS types of reports that are used by companies to evaluate projects, meet regulatory requirements and seek financing. The minimum requirements for engineering studies, focusing on the needs of financial institutions considering investment in a project, are outlined. IntroductionThe financing of mining projects in recent years has come under increased scrutiny by financial institutions owing primarily to an increasing percentage of projects whose capital expenditures had overrun project budgets or had failed to produce the economic returns anticipated during the project development process. Often, unfavorable project outcomes are not the result of widespread failures of the project engineering process but arise from inadequate engineering in limited specific areas of the project scope, such as overestimated mineral reserve, inadequate mine design, insufficient metallurgical testing or underestimated capital costs. Mill facilities and process infrastructure typically are responsible for up to 80 percent of the capital expenditures required by greenfield mining projects. They are often the project areas where capital costs are inadequately developed, and consequently are the areas highly scrutinized by financial institutions. This paper offers a perspective on the level of engineering expected by financial institutions as a prerequisite to committing support to developing mining projects.The evaluation of a mining project from exploration through development and production is a lengthy and complicated process. Mine development commitment activities for a potential project are initiated when a mineral resource is identified and continue through to the start of construction. The technical feasibility and the economic viability of each project are determined during the phases of mine development with more detailed engineering data required at each stage. There are at least four levels of engineering studies during development that are commonly acknowledged by the mining industry:"

Jan 1, 2016

The Cadia Valley Operations currently hosts a large operational open pit, a large operational sublevel caving underground mine and two other underground projects at the study stage. This scenario creates an unusual situation for the evaluation and planning of a fifth major open pit project. The Cadia East Open Pit is a large gold-copper development located adjacent to the operational open pit and above one of the underground projects. A study team is conducting a comprehensive and robust analysis of the target orebody. Two key factors for this project include the existing and planned projects within the valley and the wide range of available mining methods. The aim for the study team is to present an optimal and practical case which suits the entire Cadia Valley Operation. A rigorous and robust analysis of the situation requires that each factor be properly evaluated. A modular system has been developed which allows the wide range of scenarios to be quickly and meaningfully considered. Sensitivities for each module drive the further development of that particular module. As each scenario progresses, an assessment is made evaluating its value, strategic value and practicality. In such a way, the number of scenarios is gradually reduced at each stage to produce a final short list of feasible cases. Each scenario on the shortlist is then assessed with regard to the existing operations and other projects. A qualitative and quantitative analysis is made. This ranking is used to provide the recommended case.

Jan 1, 2007

By Mackenzie Burnett

An inducer-type pump, capable of injecting dry coal into a hydraulic transport pipeline has been developed and installed in a specially designed and fabricated slurry injector vehicle. The full scale prototype injector system can deliver up to 11 ton/min of coal into an 8-in pipeline t pressures up to 95 lb/in2. The Helical Inducer Injector operates on centrifugal principles with flow passing axially through helical pitched conical rotor. Water is delivered to the pump through an annular slot at the atmospheric pressure coal inlet. The spinning rotor maintains an air-core vortex of water which pressurizes the discharge housing. A screw feeds coal through the open inlet into this vortex. The inner radius of the vortex contracts as pressure is increased, giving a limiting maximum pressure which is proportional to the square of the rotor speed. Below this limit, flow rate, discharge pressure, und rotor speed re independent variables. The self-powered, 4 -in high slurry injector vehicle follows and receives ROM coal from a continuous miner, reduces the top size to 3-in, and delivers the sized coal to the injector feed screw for slurry formation and pumps it through a mobile hose attached to the vehicle's outby end.

Jan 1, 1983

By Stephen A. Swan

This Bureau of Mines report discusses research to analyze and evaluate extended bumper systems in order to determine the degree of protection provided to equipment operators in the event of rear-end collisions be-tween off-road rear-dump haulage trucks. The basic characteristics of rear-end collisions were determined, and a detailed analysis of the col-lision dynamics was performed to identify the magnitude and direction of impact loads, the amount of energy that must be absorbed during impact, and the major factors that affect the outcome of a collision. Separate bumper designs were developed to facilitate attachment to four 170-st-capacity haulage truck frame types.

Jan 1, 1987

By L. P. Meade

Dimension stone and salt are two of the oldest industrial minerals utilized. Salt has been and still is a necessity to the well being of man. Dimension stone on the other hand has been utilized by man to glorify conquests - both in the battlefield and corporate arena. Both commodities are important, but dimension stone has an additional use in that the survival lessons learned by the domestic industry can be applied to other contemporary industrial minerals, Specialization in the market place and customer service have allowed domestic producers to survive: subsidized foreign competition, obsolete equipment, and lack of capital.

Jan 1, 1986

By D. Harrington

Correct ventilation of underground workings whether in coal or in metal mines consists in establishing such control of air currents that the miners may work in safety, with maximum comfort and efficiency, and without impairment of health; also in controlling the air flow so that the mine workings may at ordinary times be kept reasonably free of harmful gases or dusts, and so that in time of emergency, as when a fire or an explosion occurs, there may with minimum delay be maintained as much or as little air flow as is desired throughout the mine in its entirety or in certain parts of the mine. Control of air flow is the essential point of any mine ventilating system, and is obtained only by the installation of mechanically operated fans, and other ventilating devices such as doors; overcasts, regulators, etc. Every mine, large or small, coal or metal, should from the outset be equipped with a fan. Much has been written about natural ventilation, and many claims have been made that in specific mines or parts of mines there is sufficient natural air flow. As a matter of fact, there are actually very few if any mines, coal or metal, where natural ventilation creates atmospheres anything like adequately safe or healthful for underground workers even at ordinary times or under ordinary. conditions; and at the time of a fire or an explosion mines depending upon natural ventilation are practically helpless, and are decidedly dangerous for the unfortunates forced to be in them either at the time of the disaster or afterwards when trying to handle conditions arising from the emergency.

Jan 1, 1929

By The Staff

Introduction It is the purpose of this paper to discuss a number of the metallurgical improvements in the technology of copper-nickel ore treatment which have been introduced during recent years in the plants of ?the International Nickel Company of Canada, Limited. In common with other ore treatment processes, the procedure for extracting nickel and copper is changing almost continuous! y. These changes are necessitated by reason of changes in ore grades and characteristics, rising material and labour charges, and the constant drive to maximize metal recovery and to minimize production costs. It is not possible to present a comprehensive list of all the changes made, and only a selected number of the improvements in the milling, smelting, and refining operations are covered. It should be clearly understood that some phases of the procedures described have been pioneered by others in kindred fields and due acknowledgment is given to their foresight and efforts. Articles have been published over the years describing the operations of the International Nickel Company plants and the reader is referred to the Engineering and Mining Journal, Vol. 130, No. 9, November 10th, 1930, and to the Canadian Mining Journal, Vol. 58, No. 11, November, 1937, and Vol. 67, No. 5, May, 1946. Other references are the Transactions of this Institute, 1932, 1938, and 1946; Metals Technology, American Institute of Mining and Metallurgical Engineers, February, 1938, and Canadian Chemistry and Process Industries, April, 1940.

Jan 1, 1948

On the Kinetics and Equilibrium Models for Biosorption of Ni(II) onto a Gram-Positive Bacteria Strain, Rhodococcus opacus, for Environmental Applications The aim of this fundamental study was to evaluate the biosorption of Ni(II) from aqueous solution streams onto a Rhodococcus opacus strain through kinetics and equilibrium isotherms studies. The biosorption of nickel achieved its highest value in a pH around 5. The experimental data evaluation was carried out focusing three two-parameter models, as: Langmuir, Freundlich, Dubinin - Radushkevich. In order to determine the best isotherm fit, three error analysis methods were used to assess the data: correlation coefficient (R2), residual root mean square error (RMSE) and Chi-square test. The error analysis established that the Freundlich model fits better the nickel biosorption data. Maximum uptake capacity of nickel reached a value around 7.63 mg.g-1 for R. opacus. The biosorption rate was fast and achieved a removal of around 79 per cent of Ni(II) in the first 5 minutes at room temperature (25 ¦ 2¦C). The experimental kinetics data was evaluated considering two models (pseudo-second order and pseudo-first order). The error analysis established that the pseudo-second order model better fits the data.

Sep 13, 2010

By B. Clermont

Ball mills are usually the largest consumers of energy within a mineral concentrator. Comminution is responsible for 50% of the total mineral processing cost. In today?s global markets, expanding mining groups are trying to optimize mill performances. Since comminution is concerned with liberating valuable minerals for recovery in the separation process, it is crucial to run the mills at the best operating conditions which lead to good liberation at competitive throughputs with minimum costs (energy and wear). The high availability of the equipment is also essential to maximize production and profit. To reach this key objective, continuous and reliable information about the mill operation is vital. An innovative tool which can deliver information about in-mill dynamics has been developed by Magotteaux. It can provide online and accurate measurements of the degree of grinding ball fill and pulp position for timely decision making and actions. This tool could be used on its own or linked to an automatic grinding ball loading system named Magoload. Therefore, ball load could be kept constant by using direct measurement. This article describes the Sensomag and presents some of the major improvements that can be achieved with it. Some other promising avenues are still to be explored. Keywords: Comminution, process control, process optimization, process instrumentation, online analysis.

Jan 1, 2010

By Josh B. Taggart

Some twenty to twenty-five years ago we saw the beginning of mechanization in our coal mines, It has now progressed to the point Chat as instruments of production the pick and shovel are things of the past, They had to give way to better and more efficient methods--so mechanization, followed by and combined with automation, has become common-place in our mines. Our coal could not keep its competitive position without this progress Without it our industry could not look to the future with any degress of confidence. Today we lock back and see cases of regained and salvaged markets. We see better coal products being produced at decreasing costs. We see better utilization of manpower and a stronger, more confident industry, Our hats arc off to those mining men, equipment manufacturers, labor leaders, and others who had the foresight to work toward these ends and the ability to bring them about.

Jan 1, 1962

By E. H. Denny

The presence in the Cripple Creek district, Colo., of irrespirable gas or gases, generally known to consist mainly of nitrogen and carbon dioxide, has been recognized by members of the mining industry in that region almost since underground mining was begun there; the occurrence, origin, and possible control of these gases have been discussed in several articles cited at various places in this report. Similar gases have also been studied in other metal-mining districts, as later discussed. In March, 1925, there were two fatalities from rock-strata gases in the shaft of the Index mine, near Cripple Creek. Two men repairing the bell or signal line preparatory to reopening the shaft were lowered into irrespirable gases and died. Their bodies were recovered by rescue crews from the United States Bureau of Mines and .the Portland mine, Victor, Colo. These crews found it necessary to use oxygen breathing apparatus. In October of the same year a miner was trapped on the 6 level of the Midget mine by an influx of gases that filled the shaft to a point above that where he was working. Oxygen breathing apparatus was again used by Bureau of Mines employees, who were in the vicinity, and the man was brought out in time to save his life. These two fatalities and one near fatality seemed to show that additional investigation of the gases and methods of control might be warranted. Accordingly, field and laboratory studies were begun by the authors of this report after a visit to the district by M. van Siclen, then engineer in charge, mining research division, Bureau of Mines, and after conferences with the Mine Owners' Association of Cripple Creek and with J. T. Joyce, metal-mine commissioner of the State of Colorado. The mine operators of the Cripple Creek district and the State mine commissioner's office gave whole-hearted cooperation in this work.

Jan 1, 1930

By C. F. Chung, F. P. Agterberg

"Prediction of a variable sulphur content in Cape Breton seams is important for planning the production of a highgrade metallurgical coal. Two extrapolation methods (Kriging and a version of Universal Kriging) to predict sulphur content in blocks of coal before mining are presented and applied to the New Lingan Mine reserves in the Harbour seam. The uncertainty of the predicted values is expressed by using standard deviations. Some statistical results for the Phalen seam, which occurs about 400 ft below the Harbour seam, are presented for comparison. The two mathematical models consist of two sets of equations which have been used in computer algorithms. Some limitations of the present approach and possibilities for further statistical work are indicated."

Jan 1, 1973

By G. C. RIDDELL

THE metallurgist, chemist, and physicist are blazing trails that lead far afield. Pushing on into an "Alloy Age" they see a non-ferrous era over- taking iron and steel. Delving into the nature of the physical world, they break down a supposedly indivisible element, hydrogen. Not content with terrestrial problems, they peer back along the cosmic ray into iaterstellar space, glimpsing forces that are, apparently, still busy with the task of atom-making. Mastering and organizing the material and physical, they advance steadily toward that borderland of science where the concept of matter itself seems abandoned, and force is the substance left.

Jan 1, 1930

By The Staff

FOR forty years cyanide men have been intensively engaged on the treatment of sulpho-telluride ores. So far as we know, the processes used today were-with the important exception of the concentration plus high-lime process at the Victor mill (1915)-in use, or had been tried, in the earl y years of the century. Roasting, bromocyanide, ordinary cyanide, table and vanner concentration, floating and treating the concentrate, roasting con-centrates prior to treatment, etc., all were used at Kalgoorlie in 1904 or earlier. Flotation, followed by shipment of the concentrate to the Golden Cycle mill, was the practice at the Vindicator mine, Cripple Creek, for some years prior to 1917. Similar practice was employed in the Portland Independence mill at Victor, Colorado, and was lacer superseded by the table concentration, high-lime cyanide treatment of rails of the older Portland Victor mill. During all this time, an immense amount of research was being clone on these ores by the staffs of numberless companies. Conclusions were drawn and mills built. But if the results of one per cent of this research were ever published in sufficient detail for intelligent use by others, the Lake Shore staff has been unable to discover them, or does not recall having clone so. Government laboratories-as for instance chose of the Mines Branch, Ottawa, in or about 1927-have touched upon certain methods in their publications, but they simply have not had the time to finish the job. The paper by W. E. Johnston, Tellurides-Problem or Alibi? (E. & M.]., Aug., 1933), aroused wide interest and comment. It published conclusions, some right and some wrong, and gave the evidence adduced by the author i:n support thereof. Conclusions published without supporting evidence are to most of us worse than no conclusions at all. We suggest chat, if even one-tenth of the operators had published full, detailed results of their laboratory work, ad vance in the treatment of sulpho-telluride ores would have been very much accelerated. Therefore, we venture to inflict upon the Institute a compendium of the results of laboratory work performed during the past few years at the Lake Shore mill. It is really a summary of the more interesting results to date, prepared by the mill staff for their own use and benefit. But we hope chat the discussion under any heading is so detailed chat it will be intelligible to anyone interested in that phase of the subject.

Jan 1, 1936

By François Robichaud

"The Laronde mill has been in operation since 1988. Actual milling rate ranges from 7,000 to 8,500 mtpd. Laronde uses SAG/ball mill grinding followed by copper and zinc flotation circuits. A cyanidation/Merrill-Crowe process recovers the remaining gold and silver in the flotation tails.In 1999, the carbon in pulp circuit was replaced by a Merrill-Crowe circuit in order to cope with a much higher ratio of silver/gold associated with the discovery of the Penna shaft. Marine type diatomaceous earth was used as filter aid in both clarifier pressure leaf filters and recessed pressure filter presses from 1999 to 2005. In 2005, this filter aid was gradually replaced by alpha-cellulose after several laboratory and plant filtration trials. The selected cellulose is considered to be much less sensitive to parameters such as pH and reagent concentration and have increased clarifier and filter press filtration performance. Also, since cellulose is exothermic, replacing diatomaceous earth with cellulose as filter aid in the filter presses has increased calcining and oxidation rates in the calcining ovens since cellulose is exothermic. Finally, better calcining conditions have resulted in energy and reagent savings at the arc furnaces.This paper describes how the filter aid replacement has contributed to increasing productivity and Net Smelter Return of the refinery while reducing worker’s hazards and operating cost.INTRODUCTIONAll Merrill-Crowe circuits in the world are operated with filter aids. For years, the market for precoat filter aid has been dominated by mineral filter aids such as diatomite and perlite. Flowsheet and equipment selection at the Laronde refinery were performed in the late nineties. At that time, some key parameters of the design criteria had clearly identified marine type diatomaceous earth (DE) as the most successful filter aid. Parameters such as reagent cost and availability, clarity of the filtrate solution and good historical filtration performance in other concentrators had designated DE as the best suited filter aid. Pregnant solution processed in the refinery from its start-up through 2001 was fairly stable in flow rate and reasonable in terms of impurity content (cationic and anionic compounds)."

Jan 1, 2007

By E. J. Gleim

To make a thorough survey of a coal mine in order to eliminate hazards, the competent safety engineer must be familiar with mere than one branch of engineering. It is essential that he know the properties of mine gases and the methods of detecting them, as well as hew to prevent dangerous as accumulations. It is also essential that he understand the action of overlying strata when the coal is removed, and the proper methods of protection by timbering or other suitable means of support. He must know the value of protective clothing in reducing injuries and mast be informed as to the correct handling and use of explosives to avoid premature blasts, misfires, and ether failures in blasting practice. He must understand hew to operate locomotives and cutting, loading, and various other types of machines to be able to recommend effective safeguards for protecting the men who use them in addition to being informed as 'to these and many ether activities connected with the mining of coal, he must net overlook electrical engineering if he wishes to combat the fire, shook, and ignition hazards attendant upon the use of electrical machinery and circuits in and around the mine intelligently. There are many points relating to safely in the selection, maintenance, and use of electrical circuits and equipment that are perfectly obvious to the electrical engineer but perhaps are not se evident to those not trained in this particular branch of engineering. Engineers of the U.S. Bureau of Mines who have made a special laboratory study of electricity as related to safety in minus haw e also made inspections of electrical installations at a large number of bituminous mines. These inspections have revealed practices and conditions that not only do not contribute to safety but that add nothing to efficiency and economy in the operation of the mine.

Jan 1, 1936

By D. W. Bridges, R. O. Dannenberg, Laird Crocker

Preliminary solvent extraction studies , reported by the Bureau of Mines (5) , have been continued and expanded to improve on the previous estimate of process requirements . The solvent extraction portion of the process was examined at a scale large enough to enable meaningful extrapolation of the results to geometrically similar equipment of plant size . About 82 pct of the beryllium was recovered from approximately 0.5 pct beryllium oxide (Be0) Spor Mountain , Utah , ore by a process involving ( 1 ) sulfuric acid leaching , ( 2 ) counter current decantation (CCD ) washing , (3 ) iron ( III) reduction by sodium hydrosulfide ( NaHS ) , ( 4 ) beryllium solvent extraction by di - 2- ethylhexyl phosphoric acid ( EHPA) , ( 5 ) caustic stripping of beryllium- bearing EHPA, (6 ) hydrolysis of sodium beryllate - caustic strip liquor , and (7 ) calcination of beryllium hydroxide (Be ( OH ) 2 ) formed in step (6 ) . The resulting beryllia assayed 98 to 99 pct Be0 and was suitable for most nonnuclear uses . Best overall results were obtained by using pH 2 , 1.6 grams of BeO per liter of leach liquor as feed and 0.25 N EHPA in kerosine containing 2 wt vol pct (grams per 100 ml of solution ) isodecanol ( IDA ) as solvent . Analysis of the data indicated that a commercial plant would achieve 95- pct overall extraction operating at 45 ° C with 20 hp per 1,000 gal of dispersion in each of seven mixer- settlers , having 290 gal per ton of ore hourly mixer capacity and 90 gal per ton of ore hourly settler capacity . At least 79 lb H2SO4 , 13 lb sodium hydroxide (NaOH ) , 3 lb NaHS , 0.25 lb kerosine , 0.07 lb polyacrylic flocculant , 0.03 lb EHPA , and 0.007 lb IDA would be required in H2SO4 leaching and subsequent processing to recover 1 lb BeO .

Jan 1, 1964

By Reichmuth, Donald R.

Most brittle solids are relatively weak in tension and this weakness can be very significant in determining their performance in structures and excavations. Consequently, accurate knowledge of the tensile strength of brittle materials has long been recognized as important. In the past, measurements of the tensile strength of materials such as concrete, ceramics, and particularly rock have been hindered by problems encountered in fabricating test specimens and in accurately loading them. These difficulties have resulted in a scarcity of published tensile strength data. This can be readily seen in tabulations such as Wuerker's "Annotated Tables of Strength and Elastic Properties of Rocks.

Jan 1, 1968