Search Documents

By Narasimha Mangadoddy

The complex nature of multi-phase flow in dense medium cyclones has restricted plant operators and designers to rely on empirical equations for predicting the performance. A number of empirical cyclone models have been developed in the past (Wood, 1990; Dunglison, 2002). In recent years, this subject has been broached with computational fluid dynamics (CFD). Most of the CFD models have not considered the correct rheological behavior of magnetite medium while simulating the medium segregation inside the cyclone. These models mostly predict excessive underflow volumetric flow rates. In this paper simulations of magnetite medium in a dense medium cyclone, were conducted in FLUENT where the particle phases were simulated using the modified Mixture model. The turbulence was resolved using Large Eddy Simulation (LES) model. The rheological behavior of medium was considered in the form of Granular viscosity, Newtonian and Non-Newtonian models corrected with particle loadings and fraction of ultrafines. Multi-phase simulations using granular viscosity option although predict the overall split product medium densities reasonably close to experiments, the mixture viscosity values are restricted to substantially lower values, similar to water viscosity. Simulations using Newtonian viscosity model corrected with particle loading, and fine fraction below 53µm size is predicting overall mixture viscosity levels well over water viscosity levels, but under predicting the under flow the underflow medium density. Multi-phase simulations using Non-Newtonian Herschel-Buckley model, calibrated for superfine magnetite medium measured viscosities, is closely predicting the medium segregation with gamma ray tomography data. Overall predicted product medium densities, underflow volume split are close to the experimental data. This model is can be further used to simulate coal portioning and hence in developing new designs.

Sep 1, 2012

By AIME AIME

HOLDING the annual dinner-dance of the Institute at the Waldorf-Astoria had become such a tradition that there was widespread regret when it became known that the demolition of the building to make way for a huge office structure would perforce bring to an end the long and enjoyable series of gatherings our Institute had held there. This year the . Commodore was the place at which it was held and the commuters on the New York Central and the New Haven railroad systems, at least, found it a more convenient place for them. Except for the famous "Hoover" dinner, which will probably set a mark for all time, it was the largest dinner the Institute held, 1000 being present, and it taxed the facilities of the hotel to the utmost.

Jan 1, 1930

By Mikula Adolf

Lead-tin solders are commonly used in electronic packaging due to their unique combination of electrical, chemical, physical, thermal and mechanical properties. Since it is known that lead and lead containing alloys cause great environmental concern and health hazards it is necessary to replace lead in solder materials. Besides the environmental concerns new technologies in electronic packaging require new and improved solders. In most cases the new solders will consist of temary or quarternary alloy systems, the main component will be tin or indium and the second element could be bismuth. silver, copper and gold and to improve certain properties a third element will be added. For a third element zinc, nickel, antimony and aluminum can be considered. This report will concentrate on solders containing zinc as an environmental safe. element.

Jan 1, 2003

By M. A. Oskouei

Draglines are dominant machines and the most electricity consumers in surface coal mines. With the growing price of energy, environmental concerns, and the high sensitivity of mine profitability to dragline productivity, any improvement in efficiency of draglines can be beneficial for mines. Research has shown that operator skills have a significant impact on energy efficiency of loading machines. This study suggests a method to identify the key parameters that lead to differences in operator energy efficiency (responsible parameters). First, correlation analysis is used to identify parameters that are correlated to energy efficiency. Second, linear regression of a difference matrix is used to determine responsible parameters. Since this method is based on pair-wise comparison of operators, equal number of cycle is required for pairs of operators. Complete case analysis (CCA) is used to handle missing data problems. The final conclusion is made after removing the effect of random sampling and by considering all pairs of operators. Identifying responsible parameters can improve operator training programs. The suggested method is illustrated with a case study using field data.

Feb 23, 2014

By Ofra Damm, v du Preez, D. van Vuuren, L. Simpson, H. Chikwanda

"South Africa is the world?s second largest producer of titanium bearing minerals, but apart from producing titanium mineral concentrate to form TiO2 slag, little further value is added in South Africa to mined minerals. Various studies were undertaken by both government and the private sector in an un-coordinated manner until 2007 when the South African Department of Science and Technology (DST) planned and adopted a national strategy to establish a local titanium metal industry through the research and development of key technologies that would provide a competitive advantage to such a local industry. The strategy entailed a two-pronged approach in the development of this capability, viz. simultaneous investments in the development of high-level human capital and technology in the fields of titanium metal powder production and downstream titanium metal powder processing technologies. To date significant progress has been made to establish research and/or pilot scale facilities in the following technical areas: TiCl4 production technology, titanium powder production technology, high energy milling of titanium powder, metal injection moulding facilities, rapid production of large components using laser additive manufacturing technology, investment casting of titanium, resource efficient machining of titanium and friction stir welding of titanium. Supporting technologies are also at an advanced stage through investments in titanium powder spheroidization and direct rolling of titanium powder. The intent with investment in some of these areas is not to develop new technology per se, but rather to establish local capability that will position South Africa to collaborate with other organisations in the world so that technologies can be acquired and transferred when needed in the future."

Jan 1, 2014

By Norman Orr, J. W. Gregg, Jack Wahl

The Pembina Cardium pool is a low permeability, stratified, solution-gas drive reservoir. Water-flooding has proven to be an effective means of pressure maintenance for all areas of the pool in which an economic rate of water injection can be maintained. The majority of water injection wells in the pool are converted oil well~ with capacities greater than 100 millidarcy-feet. If the average injection rate per unit of capacity can be in-creased the lower capacity areas of the pool can be economically flooded. Theory, laboratory work, and two . early miscible-flooding projects with-in the pool suggested that average water injection rates for converted wells could be increased two to three-fold by the initial injection of natural gas liquids and natural gas. How-ever, these two early projects received volumes of natural gas liquid!:' and high-pressure natural gas which would be economically prohibitive for routine stimulation. Area D, one of the Five-

Jan 1, 1962

By P Vaikkattil, K Li, J Bullock

Unlocking maximum value is essential when designing a stope and the associated drill and blast packets. This is becoming increasingly important at Olympic Dam as the operation continues to expand south into the new mining areas away from existing infrastructure, increasing operating costs and required capital investment; into areas with less competent ground conditions, requiring smaller stopes and increased interactions. The introduction of Orica’s WebGenTM system is one way in which Olympic Dam can continue to unlock value into the future by decoupling traditional drill and blast limitations. The Lime 390 stope was the first stope at Olympic Dam to trial the new technology on the last blast packet. This paper reviews the drill and blast design of the Lime 390 stope, including the technical and operational challenges associated with the stope and the trial of the Orica’s WebGenTM system for the firing of the last blast packet.

Mar 15, 2021

By R. R. Klimpel

This paper demonstrates, using the results of an unusually complete industrial test sequence, what the various interactions are between grind size, collector dosage, and frother type. While particle size is universally acknowledged to be important in optimizing industrial copper sulfide rougher flotation circuits, many of the various interactions that do occur at the industrial level with particle size are still being identified and/or quantified. This study also presents, in a consistent manner, the changes in flotation kinetics that occur as a function of particle size, in a typical industrial circuit along with some insights as to how flotation operators can optimize rougher circuit performance.

Jan 1, 1993

By A. G. Loomis

Although secondary-recovery methods have not been applied widely in California, it is apparent that increasing attention and effort must be given to this phase of recovery if the State is to maintain its high rank as a petroleum producer. Steadily increasing demands for petroleum products and decreasing rates of discovery of new oil fields and rapid depletion of existing reserves emphasize the prospect of an adverse situation of supply and demand in the not-far-distant future. If the trend of discoveries becomes more favorable or if more complete economic recovery of the oil in place can be obtained by secondary recovery, this situation can be averted. Not only are these reserves of economic importance to the petroleum industry to meet increasing market demands, but economic reclamation of such reserves is an important conservation measure, which will prolong the productive life of many fields" Accordingly, progressive operators in California are alert to the possibilities of secondary recovery and have done much to implement such operations wherever feasible. Most of the operations are of the pressure-maintenance type} in which the reservoir pressure is maintained or partly maintained by injecting natural gas to increase oil recovery. The possibilities of recovering additional oil from stripper fields by gas drive and water flooding (including water disposal) also are being tested in experimental field projects. Table 1 summarizes gas and water-injection projects in California.

Jan 1, 1952

By Frame Ritzert, Dennis Keller, Vijay Vasudevan, David Arenas

"An investigation was conducted to describe topologically close packed (TCP) phase instability as' a function of composition in the advanced ·Ni-base superalloy Rene N6. TCP phases are detrimental to overfill high-temperature performance of Ni-base superalloys because of their brittle nature and because they deplete the Ni-rich matrix of potent solid solution strengthening elements. Thirty-four variations of polycrystalline .Rene N6 determined from a design-of-experiments approach were cast and homogenized at 13 l5°C for 80 hours followed by exposure at 1093°C for 400 hours to promote TCP formation. The alloys had the following composition ranges in atomic percent: cobalt 10.61 to 16.73, Mo 0.32 to 1.34%, W 1.85 to 2.52%, Re 1.80 to 2.11%, Ta 2.36 to 3.02%, Al 11.90 to 14.75%, and Cr 3.57 to 6.23%. Physical and chemical characteristics of all microstructures obtained were described using various analytical techniques. From these observations, a mathematical description of TCP occurrence (s and P phase) was generated for polycrystalline Rene N6.IntroductionNi-base superalloy single crystals represent the state-of-the-art for turbine engine airfoil application as they offer the best balance of properties to allow for the high operating temperatures required: for efficient engine operation.1 Current trends in alloy design take advantage of improved creep rupture strength with the addition .of higher levels of refractory elements. 2 In .particular, the addition of significantly higher levels of Re in third generation superalloys is key for both microstructural stability and creep rupture strength. 3 While the presence of the refractories is thought to provide strength benefits from solid solution hardening, a tendency for alloy instability in the form of topologically-close-packed (TCP) phases or secondary reaction· zone (SRZ) ·phenomena accompanies the high refractory content. 3 The formation of these phases in sufficient amount is detrimental to the overall high temperature performance of Ni-base superalloys because of their brittle nature and because they deplete the Ni-rich matrix of potent solid solution strengthening elements.4 The tendency for a particular composition to form TCP may not be immediately known since the precipitation of TCP phases in Ni-base superalloys is nucleation controlled, thereby requiring long times at elevated temperatures to precipitate. 5 They preferentially nucleate along the octahedral planes of the Ni-base superalloys, usually in areas of refractory metal enrichment at grain boundaries or inside dendrites.5-6 In Rene N6, two closely related TCP phases, a and P, have been observed.2"

Jan 1, 1998

By G J. Halstead, R C. Steinhaus

The True Pipe® in-line sampler was developed in an attempt to address the need for a mechanically reliable and correctly designed sampler to suit one-dimensional pressurised slurry pipelines, often found in metallurgical process plants but for which no reliable and representative sampling solution as yet exists.The design, whose operation is based on the principle of symmetry, is described by Dominique François-Bongarçon (2005) with the synchronous opening and closing of relevant valves. It representatively isolates portions of the particulate material stream at predetermined intervals for effective extraction of primary increments for subsequent sample compositing.Theory of Sampling applicable solutions have proven elusive in flowing pressurised particulate material streams, with various attempts to date not having formulated a viable, mechanically reliable and acceptable design.Compliance to sampling theory is critical, and a number of tests were conducted where certain operating parameters were altered to determine their influence and sensitivity on sampling representativeness.The results of the initial series of tests performed on a carefully designed rig are presented, with additional work discussed for necessary investigation in the near future.Getting closer to a robust, economic and correct design for this challenging application in the minerals industry may now not be that far away. Plant management staff will see improved metallurgical mineral balances around their process plants and significantly reduced sampling discrepancies, particularly in tailings applications. Improved quality control is now possible where, due to plant head room constraints, classical cross stream sampling methods cannot be employed.CITATION:Steinhaus, R C and Halstead, G J, 2014. True pipe sampler – a correct design utilising the principle of symmetry in pressurised slurry particulate streams, in Proceedings Sampling 2014 , pp 127–134 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 29, 2014

By I. Sedat Buyuksagis, Jamal Rostami, Ali Naeimipour

"Improving the safety of underground openings and optimizing ground support systems requires reliable ground characterization. This includes understanding the joints, discontinuities, and rock strength. Joint information can be obtained from borehole cameras, but measuring in-situ rock strength is very difficult. Use of borehole probes can be an ideal and efficient way to meet this requirement. This paper discusses the development of the Rock Strength Borehole Probe (RSBP) and presents the preliminary laboratory/field test. This device can be an accurate, flexible, quick, non-disruptive, and cost-effective alternative to estimate the rock strength inside boreholes in underground mines and tunnels. In addition, the scratch testing procedure in the laboratory by means of a newly developed miniature linear cutting machine is explained. Based on the results of these tests, two equations are developed to estimate the uniaxial compressive strength (UCS) and Brazilian tensile strength (BTS) of the sedimentary/metamorphic rocks. These equations, are based on testing 27 different sedimentary, igneous, and metamorphic rocks by full-scale scratch tests, including the cutting tests by a miniature disc. The results show a good correlation between the normal force and the compressive strength of sedimentary rock if the depth of the scratch is known. No significant correlation was observed for igneous rocks, due to the impacts of grain size.INTRODUCTIONEstimated rock mass properties are essential input for geomechanical studies and stability analysis for any structure constructed in or with rock. The availability of geological information is the crucial component of rock mass classification. One of the important parameters in evaluating rock mass properties is the intact rock strength. This parameter is usually measured by testing the core samples, obtained from exploration boreholes. These samples are subsequently tested in geomechanics laboratories. The test results offer limited information about the rock at the few boring locations despite all the efforts and costs. In addition, these results may not necessarily be representative of the behavior of the rock in the field as the test cannot provide the insitu condition of the ground."

Jan 1, 2016

By H. E. McKinstry

LIKE nearly everything else, mining geology has been reconverting. Many geologists had been in military and other government service. Many more, with mining companies, had been working primarily toward increasing production from known reserves. All of these are turning now toward their normal peacetime endeavor-the search for new ore; for most mining companies, finding themselves with accumulated deficits in development work, are more than ready to go ahead with their postwar plans made a year or more ago but still stalled at the close of 1945 for lack of man power. These plans include not merely development in the old home camp but also wide exploration for new prospects both domestic and foreign. Most of the large concerns have geologists and engineers in the field in the United States, despite the outlook for higher mining costs here, and at least half a dozen strong American companies are already investigating opportunities abroad, notwithstanding past unhappy experiences in certain Latin-American nations which have welcomed capital but later found means of preventing investors from reaping the reward of their enterprise. A few of these new foreign expeditions are following well-planned programs, but too many, in their haste to get any sort of footing, are proceeding without well-considered policy. with the result that their geologists can do little more than desultory scouting.

Jan 1, 1946

By Phillip J. Mackey, Susumu Okabe

Copper mining and smelting has been carried out in Japan for over 13 centuries and in fact stretching back into antiquity. In 1889, the first electrolytic copper refinery in Japan based on Elkington’s principles was started by Furukawa Mining at Honjyo in downtown Tokyo based on the multiple or parallel system. Within two decades, a number of other copper refineries had begun operation. Interestingly, but perhaps not surprising given Japan’s long history of copper production, this first refinery in Japan commenced just ten years after the first refinery in the USA (1879), and not long after the first plants in Europe. By 1935, as a result of growth in copper demand, there were six domestic copper electro-refineries in Japan with an installed capacity of 97,800 tonnes/a, while actual production was 71,200 tonnes/a. Since about 1932, the majority of these plants were based on the more common parallel or multiple system. In 1946, just after World War II, domestic production capacity had dropped considerably to 29,000 tonnes/a, however with reconstruction, capacity and production expanded rapidly, with production reaching 81,000 tonnes/a in 1955, 187,000 tonnes/a in 1960 and 307,000 tonnes/a in 1965. The introduction of the first refinery and the early ones that followed and subsequent developments are discussed in this paper. The major technical achievements during the high growth period from 1945 to 1963 included: the use of fire- refined anodes; the introduction of newly-developed rectifiers; the introduction of lead-lined or vinyl-lined concrete cells; improvements in the electrolyte heating system; application of improved anti-corrosion materials and the introduction of heat-insulating surface coverings. In 2018, Japan’s refined copper production totaled 1,595,000 tonnes of copper, with Japan ranking third in the world after China and Chile. INTRODUCTION In 2018, Japan’s refined copper production totalled 1,595,000 tonnes of copper and Japan ranked third in the world for refined copper after China and Chile (Wood Mackenzie, 2019). There are now eight copper refineries in Japan which provide Japan’s production of refined copper. These plants are listed in Table 1 (Wood Mackenzie, 2019), also showing the production trend since 2013; in general, production over this period has been relatively steady. The Toyo plant is now the 7th largest copper refinery in the world after several large plants as rated by capacity in China, Russia and India (ICSG, 2019).

Jan 1, 2019

By Ana Carolina Fernandes Reis

O objetivo do trabalho foi investigar a recuperação metalúrgica da flotação de sulfeto de ouro utilizando diferentes tamanhos de partículas, a partir de ensaios de moagem e flotação em bancada, visando analisar o melhor desempenho e seletividade do processo. O minério em estudo apresenta um teor médio de ouro de 5,28 ppm e 0,59% de S. Nos testes verificou-se uma correlação diretamente proporcional entre a recuperação mássica e metalúrgica, ambas mostraram-se inversamente proporcional a seletividade no concentrado. A granulometria com 90% passante na malha de 0,053mm obteve o melhor resultado de recuperação tanto do ouro como de sulfetos, em contra partida, apresentou o menor grau de seletividade.

Aug 16, 2017

By D. F. Malan, J. C. Esterhuyse

"Mining in the Carletonville area of the Witwatersrand Basin predates 1934. Owing to the depletion of higher grade ore, the current activities focus increasingly on the extraction of lower grade secondary reefs as well as remnant extraction. Of particular interest is multi-reef remnant extraction. Numerical modelling was conducted to investigate some rock engineering aspects of remnants being understoped on a secondary reef horizon. An analysis of the stress evolution in the middling between two reef horizons indicated that a zone of high major and low minor principal stress develops between the two reefs. This indicates a high risk of violent shear failure. Some pillars were nevertheless successfully understoped in the past and a study was conducted to better understand this phenomenon. An ’extended’ energy release rate concept introduced by Napier and Malan (2014) proved to be useful for investigating this problem. It was found that bedding planes and lithology appears to play a role in the stable dissipation of energy in multi-reef remnant geometries. The study indicated that the stope convergence and the various energy components are affected by the presence, position, and properties of a bedding plane. The energy solutions are complex and sometimes counterintuitive. Care should be exercised when modelling specific cases. The modelling was nevertheless valuable as it indicated that energy dissipated on weak layers may reduce the risk of violent failure in a multi-reef mining scenario. Additional work is required to investigate if crushing on the reef plane plays a prominent role when mining these remnants. IntroductionTo extend the lives of the Witwatersrand gold mines, work is being conducted to include a larger number of remnants and pillars in the reserve base of the mines. According to Jager and Ryder (1999), a remnant is an unmined block of ground surrounded by extensive mining. Remnants are typically left because of adverse or difficult mining conditions caused by geological structures, poor ground conditions, low grade, or rockburst damage (Durrheim, 1997). In contrast, pillars are typically the result of rock engineering designs to control energy release rates (ERR) and seismicity. During the early 1900s, remnants formed by the practice of scattered mining layouts had a significant effect on seismicity. Numerous task teams were appointed during this period. As the industry expanded, the severity of rockbursting increased and the research was formalized after the 1960s. Various recommendations were made and many of these are still used as best practice today (e.g. Jager and Ryder, 1999)."

Dec 1, 2018

By Edward D. Thimons

Inflatable stoppings are currently marketed for production use, and numerous mining companies have become interested in using such stoppings in rescue and recovery operations. The Bureau of Mines therefore evaluated the concept of using inflatable stoppings in emergency situations. The stoppings tested by the Bureau were 12-foot-diameter spheres inflated with a blower operated by a small battery pack. Experiments were conducted with the stoppings in a full-scale wooden mine model to evaluate their ability to withstand sliding or slipping at various internal and differential pressures, puncture resistance, various inflation techniques; and internal leakage from the stoppings. The stoppings were then installed and tested in the Bureau's Safety Research Coal Mine at Bruceton, Pa., to determine their effectiveness as mine air barriers. Despite some encouraging results obtained with the model and in-mine studies, the stoppings did not perform well in two operating metal mines where they proved difficult to erect and inadequate as air barriers.

Jan 1, 1976

By C. Musingwini, A. S. Nhleko, M. J. Mahase

"In an environment like the mining industry, which is characterized by different stakeholders with multiple objectives, multi-criteria decision analysis (MCDA) is a useful approach for optimal decision-making. The application of MCDA techniques in the mining industry has predominantly been in mine planning and related problems, although no comprehensive survey has previously been undertaken to establish the application trends. A survey of the use of MCDA techniques was therefore conducted using case studies from the literature. It was noted that often two or more methods are applied to the same problem in order to increase confidence in the solution derived. As the number of criteria and alternatives increases, some methods become inefficient. A combination of the analytic hierarchy process (AHP) method with other MCDA techniques was the most frequently used approach, indicating the efficiency of the AHP method, especially when evaluating problems with more criteria and fewer alternatives. A combination of fuzzy theory with AHP or other methods incorporates uncertainty. The findings from the survey will benefit users applying MCDA techniques to solve mine planning and related problems.IntroductionA country’s natural resources serve the needs of different groups of people within the country. These different groups are collectively known as stakeholders (Herath and Prato, 2006). Stakeholders have different needs, preferences, and expectations, which describe and define the criteria to be considered in decision-making. The options available as solutions describe the alternatives in decisionmaking theory. The criteria and alternatives have to be evaluated simultaneously when making decisions, and this is when multicriteria decision analysis (MCDA) techniques become invaluable (Herath and Prato, 2006) because the human mind is considered to be limited when solving complex and intangible problems with several criteria and alternatives (Saaty, 2007). MCDA techniques belong to a broad group of techniques called multi-criteria decision-making (MCDM) techniques. The other group of techniques within MCDM comprises the multi-objective decision-making (MODM) techniques. MODM techniques are generally used to solve problems with an infinite number of alternatives, while MCDA techniques are generally used to solve problems with a finite number of alternatives (Musingwini, 2010)."

Jan 1, 2016

By M. Ericsson

?Rare earths ?will not be bargaining instruments?? was stated in a headline in China Daily of 29 October 2010. The Chinese government is trying to fend off the persistent accusations from Japan, the USA, and Europe that it is manipulating the supply of these so called ?critical? metals to gain political and economic advantages. The critics maintain that China has taken the rest of the world hostage by controlling 97% of the resources of rare earths. These elements are crucial in a number of high-tech applications. They are not impossible to substitute, but difficult to do so effectively. The name ?rare earth? is a misnomer, as even the least abundant is 200 times more common in the Earth?s crust than gold. They are, however, difficult to find in economic concentrations. The Chinese near-monopoly over the rare earths, together with China?s scramble for other resources in Australia, Africa, and elsewhere around the world, is seen as an example of a Chinese strategy to take control of vital metal resources. The Chinese are also accused of using unfair and sometimes illegal business practices in this fight for resources. Practices which, critics claim, put the Chinese interests above the interests of the host countries, in particular in Africa.

Jan 1, 2011

By John Barber

The Deep Ore Zone (DOZ) Mine is PT Freeport Indonesia's (PTFI) newest operation. Production at the mine began in September 2000. The DOZ Mine produces 25 kt/d (27,500 stpd) using mechanized block cave mining methods. The DOZ Mine has several major improvements when compared with previous block cave mines in the district. It has an independent and improved ventilation system, a flexible and efficient truck haulage system, and a more reliable crushing and conveying system. PTFI's copper and gold mining complex is located in the Ertsberg mining district in Irian Jaya, Indonesia (Fig. 1). The Ertsberg district is located in the Sudirman Mountains at elevations from 3,000 to 4,500 m (9,800 to 14,700 ft) above sea level. The topography is extremely rugged and rainfall in the mine area averages 3,000 mm/a (118 in./year). Freeport began production in the district in 1972 when the mill began processing ore from the Ertsberg openpit. Underground mining began in 1980 when the Gunung Bijih Timur-Ertsberg East (GBT) Mine was brought online using block caving methods. In 1991, the GBT Mine reached a maximum production rate of 28 kt/d (31,000 stpd). Ore from the mine was exhausted in 1994. The Intermediate Ore Zone (IOZ) was brought into production in 1994. It, too, used block caving methods and had a design rate of 10 kt/d (11,000 stpd). The IOZ is currently producing at a rate of 21 kt/ d (23,000 stpd). The DOZ was discovered in the mid-1980s by deep drilling from the GBT. The GBT, IOZ and DOZ deposits are all situated in the Ertsberg East Skarn System (EESS). In 1993, the first of several studies was completed that indicated that portions of the DOZ Mine could be economically mined using block caving methods. Limited development was started in 1995. Full-scale development and construction began in late 1997. The crusher and conveying system began operating during the first quarter 2000. The first of two main exhaust shafts has been com¬missioned, along with three of the four new main fans. The second exhaust shaft and fourth main fan will be in service by the end of 2001. Undercutting and production began in September 2000. The DOZ Mine will reach its design production rate of 25 kt/d (27,500 stpd) in 2003. A study is under way to determine if an ultimate production rate of 35 kt/d (38,500 stpd) is feasible.

Jan 1, 2001