Search Documents

By Jos. Van Ackeren

Although the Siemens regenerator principle was introduced into byproduct coke-oven design about 40 years ago, many problems of construction, and particularly of heat distribution and pressure conditions, have not been fully solved. Heat should be applied to the walls of a coke oven in such a way that the coking of the charge of coal will be completed everywhere at the same time, and at approximately the same temperature. This means that the application of heat should be uniform from the top to the bottom of the coal mass (except for the thin layer at the top that is purposely kept at a somewhat lower temperature to reduce cracking of the byproducts); also that a little more heat must be applied to the coke end than to the pusher end, because the coal mass is a little thicker at that end. As a modern coke oven is about 40 ft. long and 12 ft. high, a real problem is involved in the proper application of heat to the oven walls so as to secure quick coking time (without endangering the walls through local overheating) and produce coke made at a uniform temperature. Design of Ovens In all regenerative ovens, the points of combustion are arranged in duplicate sets, one set operating in one-half the area of the heating wall and the other set alternately operating in the other half. Because of the reversal of the flow of gases, the points of maximum and minimum temperatures are alternately located at the same places, thus preventing dangerous local overheating. The practicability of the principle of reversal of flow seems to have been recognized at an early date, and has been applied with every conceivable flue arrangement, combustion chamber, and means of air and gas supply. To summarize the various principles that have proved useful for the control of oven-wall temperature, the best practice seems to have resulted from the acceptance of the use of vertical flues; the separate supply of air and gas to the base of these flues, with the resulting flame

Jan 1, 1923

By Jos. Van Ackeren

Although the Siemens regenerator principle was introduced into byproduct coke-oven design about 40 years ago, many problems of construction, and particularly of heat distribution and pressure conditions, have not been fully solved. Heat should be applied to the walls of a coke oven in such a way that the coking of the charge of coal will be completed everywhere at the same time, and at approximately the same temperature. This means that the application of heat should be uniform from the top to the bottom of the coal mass (except for the thin layer at the top that is purposely kept at a somewhat lower temperature to reduce cracking of the byproducts); also that a little more heat must be applied to the coke end than to the pusher end, because the coal mass is a little thicker at that end. As a modern coke oven is about 40 ft. long and 12 ft. high, a real problem is involved in the proper application of heat to the oven walls so as to secure quick coking time (without endangering the walls through local overheating) and produce coke made at a uniform temperature. Design of Ovens In all regenerative ovens, the points of combustion are arranged in duplicate sets, one set operating in one-half the area of the heating wall and the other set alternately operating in the other half. Because of the reversal of the flow of gases, the points of maximum and minimum temperatures are alternately located at the same places, thus preventing dangerous local overheating. The practicability of the principle of reversal of flow seems to have been recognized at an early date, and has been applied with every conceivable flue arrangement, combustion chamber, and means of air and gas supply. To summarize the various principles that have proved useful for the control of oven-wall temperature, the best practice seems to have resulted from the acceptance of the use of vertical flues; the separate supply of air and gas to the base of these flues, with the resulting flame

Jan 1, 1923

By Leslie E. Apodaca

INTRODTUCTION The use of spiral concentrators for processing fine coal particles is an old idea that has recently gained acceptance in the 11.S. coal industry. It was not onti1 the Australian Minerals Industry developed a spiral concentrator specifically for separating coal from ash in the latter 1970's and early 1980's that spiral concentrators were seriously considered as viable equipment for processing fine coal. The Wright Coal Spiral was introduced in 1980, the Mineral Deposits Limited Mark 10 Coal Spiral was introduced in 1982, and the Vickers Wyong Coal Spiral was introduced in the latter part of 1984. Each spiral design was different and utilized constant profile troughs, constant pitch troughs, compound profile troughs, and various splitter arrangements. Mineral Deposits Limited has combined the best features of the compound profile trough and constant pitch trough with critically-placed splitters to develop the MDL LD4 spiral concentrator which is a truly efficient coal washing spiral. This spiral concentrator was introduced into the U.S. Coal Industry in 1987. Recently, Mineral Engineering Technology of the United Kingdom and Multotec of South Africa have introduced their own coal spiral designs. Spiral concentrators were first installed in fine coal processing circuits in the Australian, South African, and Canadian Coal Industries in the early 1980's and in the U.S. Coal Industry in 1985. SPIRAL CONCENTRATOR SEPARATION PROCESS The separation process that occurs within the spiral concentrator trough is very complex, as it is a combination of three gravity separation processes. When the coal slurry first enters the spiral trough, each coal and ash particle and the water is subjected to centrifugal forces. These forces cause the water, light coal particles, fine heavy ash particles, and medium middlings particles to the outer vertical portion of the spiral trough. The coarse ash particles and the coarse middling particles remain on the inside of the spiral trough. The center or transitional area of the trough contains a mixture of middlings particles and near-gravity material that is present in the slurry, as shown in Figure 1. At the same time the coal and ash particles are suhjected to centrifugal forces, the trough design (both profile and pitch) causes the particles to be subjected to flowing film and stratified bed separations. The combination of these three separations, whose efficiency is dictated by the spiral troogh design, will effect the separation of the lighter coal particles from the heavier ash and middlings particles. As the slurry flows down the spiral, the profile and pitch design of the trough will counteract the centrifugal forces on the fine, heavy ash particles and fine middlings particles and cause them to migrate from the vertical portion of the trough to the center or inner portion of the trough. At the same time, any heavy particles trapped in the transitional area of the trough will be forced to migrate to the inner edge of the trough and any coal particles will be forced to migrate to the outer edge of the trough. SPIRAL SPLI'TTEP ARRANGEMENT The critical placement of splitters along the inner edge of the trough for removal of the heavy ash particles as the slurry flows down the trough further enhances the separation of the coal particles. At the bottom of the spiral trough are product splitters arranged to make a final separation of the slurry stream into clean coal, middlings, and refuse products.

Jan 1, 1988

By P. K. Koh

Chi phase (body-centered cubic, a = 8.89A) was found in as-cast 23 pct Cr-10 pct Mo-Fe alloy as well as in heat-treated 316, 316L, 317, and modified 446 stainless steels. Chi phase resembles sigma phase in its metastability, chemical composition, and brittleness. Microstructure and some of physical properties of chi phase were developed. MOLYBDENUM has been established as a desirable alloying element for the enhancement of corrosion resistance in Cr-Ni steels and creep and rupture strength in high temperature alloys. On the debit side, however, the molybdenum addition has been known to stimulate u formation. When the molybdenum-bearing steels were subjected to prolonged heating at elevated temperatures, losses of corrosion resistance and/or ductility have been observed. Andrews1,2 first found the existence of a new phase among the anodic FeC13 extracts from type 316 stainless steel solution treated and then reheated from 800" to 1100°C. This phase was designated x and was identified by diffraction patterns as of body-centered cubic structure with a value equal to 8.89? and similar to that of a manganese. He found that the x phase in this steel always coexisted with s phase, but failed to distinguish one from the other by metallographic technique. No definite conclusion was drawn regarding the equilibrium temperature ranges of these two phases. The appearance of Andrew's work recalled an un- explained structure observed several years ago at the Allegheny Ludlum Research Laboratories during the investigation of an experimental alloy containing 25 pct Cr, 10 pct Mo, and balance Fe. X-ray diffraction patterns on the as-cast material revealed the presence of a body-centered cubic phase having a lattice parameter of 8.89?. The structure was sufficiently similar to that of y chromium that for a time it was thought that the structure might be caused by the presence of some undissolved electrolytic chromium particles. The alloy as-cast was so brittle that it shattered after the slightest hot reduction by hammer cogging. This paper gives the results of some metallographic and X-ray diffraction studies on x phase as found in several experimental alloys as well as a few molybdenum-bearing commercial stainless steels. The analyses of materials studied were as shown in Table I. Experimental Procedure Metallography: Solid specimens were polished mechanically and etched in boiling 50 pct HC1 solution in order to best delineate x and s phases in the alloys studied. X-Ray Diffraction: The difficulty of satisfactorily developing diffraction lines for s phase in solid specimens has been previously reported by Bindari, Koh, and Zmeskal.V or this reason all specimens used in this investigation were subjected to anodic

Jan 1, 1954

By G B. Ebsworth, J Krokowski de Vickerod

Several drilling programs at Maldon have produced 7790 core samples, which were assayed for gold, with 2825 of the samples assayed for nine other metallic elements. There is a lack of correlation between gold and all other elements. The situation, however, changes dramatically when sorted according to the abundance of arsenic. In the populations where As >200 ppm, there are strong, positive correlations between gold and several elements. There is also a strong positive correlation of Au with the weighted sums and products of all elements with the elemental averages as a weighting factor, and Bi*Sb and Bi*As elemental products. In these populations, there is also a strong positive correlation between the logarithms of Au and logarithms of each element, as well as the elemental sums and products described above. The correlation coefficients increase with higher As cut-off values.All elemental distributions but especially gold show a high-nugget effect and display high skewness and dispersion, low kurtosis, and common outliers. The distributions of their logarithms are several magnitudes less scattered and without outliers. Thus, the logarithmical distribution correlations are best for practical use.Correlation coefficients were T-tested and are statistically significant. The elemental correlations, particularly those of logarithmic values of weighted sums and Bi, could be used as a gold path finding tool at Maldon. After a preliminary assay for gold and arsenic, only samples with As > 200 ppm should be assayed for other elements. Higher values of gold-correlated elements or elemental ratios, in samples with low gold grades, may increase confidence that gold is under reporting due to its highly nuggetty nature.CITATION:Krokowski de Vickerod, J and Ebsworth, G B, 2012. Correlation as a gold path finding tool at Maldon, Victoria, in Proceedings Narrow Vein Mining 2012 , pp 131-144 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 26, 2012

By H. W. Hitzrot

The new 4800-ton fine-grinding plant at the Hollinger Consolidated Gold Mines property at Timmins, in the Porcupine district of northern Ontario, went into operation in November 1937, and represents the culmination of an experimental program. The plant is a moderately low rectangular building of hollow tile on a steel frame, large enough to house four 7 by 15-ft. ball mills, with a 12 by 27-ft. classifier beside each mill. At one end is space for the addition of another mill and classifier or a mill and classifier for the regrinding of table concentrates. This regrinding is now done in the old grinding department of the main mill building. Also within the new building are the four 6-in. sand pumps for lifting the product from the low-dis-charge ball mills up to the classifier feed launders and the containers and appurtenances of a complete dust-collecting system. Together with the usual overhead crane, these constitute the major units of equipment within the new plant. The location is at the lower end of the main mill buildings toward the old tailings pond, now so neatly leveled off and sodded to rival the very best of our own W.P.A. projects. Close by the new grinding plant is a large dome-shaped structure—the new fine-ore bin designed and built by Mr. Longmore and the Hollinger milling and engineering staffs. There are four separate automatically loaded inclined belt conveyors leading up from the bottom of the bin to the grinding plant. Each belt is equipped with a recording weightometer, in the grinding building. The whole structure and the machinery within it give the impression of permanence and a carefully integrated design with close attention to details, giving the operators every advantage for consistently good work. The many ideas and opinions behind this achievement were all ably organized and executed by the Hollinger milling and engineering staffs, and not a few were directly initiated by them. Excellent cooperation was afforded by the Hollinger staff to the engineers helping to conduct

Jan 1, 1939

By H. W. Hitzrot

The new 4800-ton fine-grinding plant at the Hollinger Consolidated Gold Mines property at Timmins, in the Porcupine district of northern Ontario, went into operation in November 1937, and represents the culmination of an experimental program. The plant is a moderately low rectangular building of hollow tile on a steel frame, large enough to house four 7 by 15-ft. ball mills, with a 12 by 27-ft. classifier beside each mill. At one end is space for the addition of another mill and classifier or a mill and classifier for the regrinding of table concentrates. This regrinding is now done in the old grinding department of the main mill building. Also within the new building are the four 6-in. sand pumps for lifting the product from the low-dis-charge ball mills up to the classifier feed launders and the containers and appurtenances of a complete dust-collecting system. Together with the usual overhead crane, these constitute the major units of equipment within the new plant. The location is at the lower end of the main mill buildings toward the old tailings pond, now so neatly leveled off and sodded to rival the very best of our own W.P.A. projects. Close by the new grinding plant is a large dome-shaped structure—the new fine-ore bin designed and built by Mr. Longmore and the Hollinger milling and engineering staffs. There are four separate automatically loaded inclined belt conveyors leading up from the bottom of the bin to the grinding plant. Each belt is equipped with a recording weightometer, in the grinding building. The whole structure and the machinery within it give the impression of permanence and a carefully integrated design with close attention to details, giving the operators every advantage for consistently good work. The many ideas and opinions behind this achievement were all ably organized and executed by the Hollinger milling and engineering staffs, and not a few were directly initiated by them. Excellent cooperation was afforded by the Hollinger staff to the engineers helping to conduct

Jan 1, 1939

By M. R. Geer, H. F. Yancey

0. R. LYONS*—I know that we are all interested in hearing about problems that other people have. To most of the people from the eastern part of the United States, this kind of coal preparation is completely different. It represents washing difficulties that most operators have never experienced, or, if they have, they have refused to consider them because there are coals that are much easier to wash and, therefore. they leave the more difficult ones alone for the time being. E. R. McMILLAN†—I think the au-thors have summarized the material very well. Dr. Yancey has spent a great many years in the study of washing coals, as has Mr. Geer. I might comment briefly on some of the plants that were mentioned, plants with which I have had some con-nection, particularly those of our own company, the Northwestern Improve-ment Co. I would like to point out this: that ill each case, a great deal of work was done in the way of preliminary studies of washability of the coal before plants were built. The first plant of any size built in Roslyn field was mentioned in the paper. This central cleaning plant was designed and built to handle coal from three different mines. I might say that prior to 1935, the year in which the plant was built, the coal was used largely as railway fuel, close to a million tons annually. But as mining increased in depth, it became increasingly difficult to separate and gob much of the impurities underground, with the result that the run-of-mine coal became so high in ash that the railroad eventually was forced to consider installing some kind of preparation plant at the mine. We spent about a year in preliminary studies in cooperation with the Bureau of Mines to find out the best type of plant that would clean the coal. The result, as Mr. Geer has explained to you, is a rather complicated plant, but it is doing a very satisfactory job. We have, however, made a number of changes and improve-n~euts since it was first built. The last addition was the, installation of a cen- trifugal drier to dewater the minus ¼ in. size. We are now contemplating installing heat driers for further drying of minus ¼ in. We use Vissac heat driers for drying the stoker coal, the ¾ to in. The demand for drier coal, for both railway and industrial use, is forcing us to further drying of the coal. The plant that was mentioned as having been built in Pierce County, during the war, was a government sponsored plant. I happen to have had some connection with its design, construction and initial operation. We did what we thought then, and still think, was a very thorough job of preliminary studies in cooperation with the Burea of Mines of the coal from that field. The plant was as good a plant as could be built with the equipment available at that time, 1943. The plant that was mentioned as having been built at Ravensdale for treating the McKay coal was rebuilt about two years ago, and in addition to the modified Elmore jig washer that was mentioned. we added a coucentrating table for re-cleaning the minus 3/32 in. Our object there was to produce a commercial

Jan 1, 1950

By G. S. Hume

During the war years the drilling activity in Canada has been steadily increasing and still further increase is expected in 1945. The production of oil, which in the past has come largely from the Turner Valley field in Alberta, shows a decline since 1942, the peak year. New discoveries made in 1944, however, give promise of replacing the decrease from Turner Valley where the crude-oil production in 1944 was nearly 1,800,000 bbl. less than in 1942, but with an increase of 145,000 bbl. in natural gasoline, a product of great value to the war effort. A very considerable part of the decline in Alberta has been offset by new production of more than a million barrels in 1944 from the Norman Wells field, in the Mackenzie River area of the Northwest Territories. It should not be forgotten, however, that this is largely due to the Canol development, a war project, the future of which is dependent on many factors not connected with an ordinary commercial operation. The year 1944 has been the best in new discoveries in Alberta for all time. The discovery of a new deep field at Jumping-pound, 20 miles west of Calgary, with the hopc of a type of product similar to that of Turner Valley is the culmination of many years of effort to interpret the subsurface structures in relation to the complicated surface foothills faulting and folding. In this case the subsurface structure on the Paleozoic limestone was inferred from geological investigations but precisely defined by seismograph. In addition to Jumpingpound the discovery of oil of 34.5 gravity at a depth of less than 5000 ft, in the Devonian of the Plains at Princess, 125 miles east of Calgary, is of great significance since this is the first substantial production from the Devonian in Alberta, although previously some oil had been obtained at two places from the Devonian in the foothills. The effect of this discovery is already apparent in the number of wells now drilling to the Devonian in the southern Plains. In southern Alberta a new producing area has been found in a Lower Cretaceous sand at Barnwell, a few miles west of Taber. Also, at Conrad, 20 miles southeast of Taber, an important new discovery has been made at a depth of about 3000 ft. in a sand in Jurassic shales, in a strali-graphic trap on the northeast flank of the Sweetgrass arch. In northeast Central Alberta an important extension has been found in the Lloydminster area, where only a few wells have so far been drilled. A new well 3 1/2 miles south of the previous producers found a coarser sand at the productive horizon and as a result will have an increased daily yield. At Blackfoot, 9 miles west of Lloydrninster, a new producing area in the Lower Cretaceous may have been discovered at a depth of 2004 ft. At the end of 1944 the well was being tested. Forty-four unsuccessful wildcat wells were drilled in Alberta in 1944. The decline of Turner Valley, the major producing field, was anticipated at the beginning of the war and in an effort to offset this and encourage new development the Dominion Government put into force tax concessions and other measures that,

Jan 1, 1945

By Albert L. Toenges

This report is the second of a series describing methods and systems of mechanical mining; where operations are conducted on more than one shift. The first report, Information Circular 7014,4/ describes mining operations at 14 mines and the present paper describes operations at 11 additional mines. The purpose of this study is to analyze the advantages and disadvantages of the various types of equipment and mining systems now used where more than one shift is worked per day. Physical conditions vary in different and in the same mining districts and determine, together with economical considerations, the systems of mining and the types of mechanical loading equipment to be used. The information presented in this paper may be helpful to operators or others who may contemplate installing a mechanical mining system. The equipment used in the mines described comprises conveyors, scrapers, mobile loaders, mobile conveyors, and combination of these types. The description of the mining systems and practices at the mines investigated is detailed only as they relate to and affect mechanization. In computing the operating data in mines that are not totally mechanized, employees not working directly on production have been charged to output from mechanized sections in proportion to the percentage of mechanization. The operating data for comparing various systems are for an average working dry, as the number of men working on idle days varies greatly in different mines.

Jan 1, 1939

By Theron Wasson

The oil and gas fields of Michigan that have been under development since 1925 are in an area that extends across the middle of the lower peninsula from northeast to southwest, a distance of about 200 miles, and with a width of about 80 miles. In 19 years 70 fields have been discovered. Most of these are relatively small when compared with other oil-producing areas. This is borne out by the fact that since the first wells were drilled these fields have produced a total of only 204,000,000 bbl. However, Michigan is still maintaining its production, for during the past five years the annual production has remained fairly constant at approximately 20,000,000 bbl. Production for 1943, as reported by the Bureau of Mines, was 20,682,000 barrels. Roughly, one third oi Michigan's production in 1943 came from the Reed City field, which was discovered in 1941. During the year, 237 oil wells were completed in Michigan in 1943. The decrease of 56 from the 1942 total is probably due to the continuance of Government regulations requiring a 40-acre spacing pattern over most of the state. Fig. I shows the principal oil and gas fields of Michigan, and the columnar section, Fig. 2, shows the principal producing horizons in relation to the section drilled. The data of Table I and Table 2 have been carefully checked with previous reports to eliminate errors. Six new producing areas were discovered during 1943 and five areas discovered in 1942 were developed during the year. Both the new discoveries and the 1942 discoveries that were developed appear to be small and relatively unimportant. Goodwell Field.—The best discovery of the year is the Goodwell field, T. 14 N., R. 11 W., Goodwell township, Newaygo County. This small structure was located by core testing done by The Pure Oil Co. in 1942 and early 1943. The first producing well, C. R. Harris No. I, was completed on July 5, 1943, ill the Traverse limestone at a total depth of 2742 ft., with ail estimated potential of 1100 bbl. per day. By the end of the year, 18 wells had been completed in this field and approximately 281,000 bbl. of oil produced. The field operated under proration of 262 bbl. per day per well from Oct. I to Dec. I; 150 bbl. per day per well after that date. Woodville Field.—The small Woodville pool, T. 15 N., R. 11 W., 3 miles north of the Goodwell field, was discovered by core testing by the Ohio Oil Co. The discovery well was completed on May 5, 1943, flowing 650 bbl. of fluid, including 18 per cent salt water the first 18 hr., from the Traverse limestone at a depth of 2810 to 2815 ft. Seven wells had been completed by the end of the year and 67,000 bbl. of oil had been produced. Development is now practically at a standstill because further drilling does not aDDear economically iustified.

Jan 1, 1944

By Theron Wasson

The oil and gas fields of Michigan that have been under development since 1925 are in an area that extends across the middle of the lower peninsula from northeast to southwest, a distance of about 200 miles, and with a width of about 80 miles. In 19 years 70 fields have been discovered. Most of these are relatively small when compared with other oil-producing areas. This is borne out by the fact that since the first wells were drilled these fields have produced a total of only 204,000,000 bbl. However, Michigan is still maintaining its production, for during the past five years the annual production has remained fairly constant at approximately 20,000,000 bbl. Production for 1943, as reported by the Bureau of Mines, was 20,682,000 barrels. Roughly, one third oi Michigan's production in 1943 came from the Reed City field, which was discovered in 1941. During the year, 237 oil wells were completed in Michigan in 1943. The decrease of 56 from the 1942 total is probably due to the continuance of Government regulations requiring a 40-acre spacing pattern over most of the state. Fig. I shows the principal oil and gas fields of Michigan, and the columnar section, Fig. 2, shows the principal producing horizons in relation to the section drilled. The data of Table I and Table 2 have been carefully checked with previous reports to eliminate errors. Six new producing areas were discovered during 1943 and five areas discovered in 1942 were developed during the year. Both the new discoveries and the 1942 discoveries that were developed appear to be small and relatively unimportant. Goodwell Field.—The best discovery of the year is the Goodwell field, T. 14 N., R. 11 W., Goodwell township, Newaygo County. This small structure was located by core testing done by The Pure Oil Co. in 1942 and early 1943. The first producing well, C. R. Harris No. I, was completed on July 5, 1943, ill the Traverse limestone at a total depth of 2742 ft., with ail estimated potential of 1100 bbl. per day. By the end of the year, 18 wells had been completed in this field and approximately 281,000 bbl. of oil produced. The field operated under proration of 262 bbl. per day per well from Oct. I to Dec. I; 150 bbl. per day per well after that date. Woodville Field.—The small Woodville pool, T. 15 N., R. 11 W., 3 miles north of the Goodwell field, was discovered by core testing by the Ohio Oil Co. The discovery well was completed on May 5, 1943, flowing 650 bbl. of fluid, including 18 per cent salt water the first 18 hr., from the Traverse limestone at a depth of 2810 to 2815 ft. Seven wells had been completed by the end of the year and 67,000 bbl. of oil had been produced. Development is now practically at a standstill because further drilling does not aDDear economically iustified.

Jan 1, 1944

By Alfred H. Bell, George V. Cohee

Illinois produced 146,788,000 bbl. of oil in 1940, or nearly 11.0 per cent of the total for the United States, and ranked fourth among the oil-producing states. Its production was only slightly less than that of Oklahoma, which produced 11.5 per cent of the national total. Illinois' production in 1940 represents an increase of 55 per cent over the previous year, when it amounted to 94,912,000 barrels. The development of the Devonian limestone in the Salem and Centralia fields is largely responsible for the increase in production during 1940 Production from the Devonian limestone in these two fields was estimated to be 36,698,000 bbl., or 25 per cent of the state's total production (Table I). The increase in production during June, when the state's daily average production attained a peak of 518,200 bbl. for the week ending June 29, was due to the Devonian production at Centralia (Fig. I). The initial production of the best Devonian wells in the Centralia field was as high as 12,000 bbl. in 24 hr. Daily average production in IIIinois for 1940 was 400,000 bbl. of oil, but actually daily production fluctuated widely during the year. At the beginning of 1940 daily production was approximately 330,000 bbl. During the first hali of the year it in-creased irregularly to the peak in June mentioned above and as the prolific Devonian producing areas were drilled up, the state's daily production declined rapidly during July and continued to decline, although more slowly, until the end of the year, when the daily production was approximately 325,000 bbl. The daily average production per well in the new fields at the end of the year was approximately 40 bbl. (Fig. I). Oil from the Devonian was also produced in the Bartelso field, Clinton County, the Sandoval field, Marion County, and the Irvington field, Washington County, bringing the estimated total production from the Devonian limestone to about 26 per cent of the state's total production, The remainder was obtained largely from the Mississippian system. About 2 per cent of the total was from Pennsylvanian and Ordovician strata. The decline in the Devonian limestone production has been so rapid that the 1941 output from this system will probably be only a small fraction of that of 1940 unless large new reserves are discovered. The "Trenton" (Ordovician) limestone has been tested in two wells in the Centralia field and both were small oil producers at a depth of about 4000 it. The "Trenton" also was found productive in the Salem field at a depth of 4500 ft. (Table 5). The initial production of the discovery well, which was completed shortly after the end of the year, was 130 bbl. on pump. Other wells drilled early in 1941 had initial productions averaging 172 barrels. The outlook for 1941 is for a continuation of drilling activity in Illinois, but at a declining rate (Fig. I, upper curve). The most active area at the end of 1940 was in the deep basin area in Wabash, Edwards, White, and Hamilton Counties.

Jan 1, 1941

By Alfred H. Bell, George V. Cohee

Illinois produced 146,788,000 bbl. of oil in 1940, or nearly 11.0 per cent of the total for the United States, and ranked fourth among the oil-producing states. Its production was only slightly less than that of Oklahoma, which produced 11.5 per cent of the national total. Illinois' production in 1940 represents an increase of 55 per cent over the previous year, when it amounted to 94,912,000 barrels. The development of the Devonian limestone in the Salem and Centralia fields is largely responsible for the increase in production during 1940 Production from the Devonian limestone in these two fields was estimated to be 36,698,000 bbl., or 25 per cent of the state's total production (Table I). The increase in production during June, when the state's daily average production attained a peak of 518,200 bbl. for the week ending June 29, was due to the Devonian production at Centralia (Fig. I). The initial production of the best Devonian wells in the Centralia field was as high as 12,000 bbl. in 24 hr. Daily average production in IIIinois for 1940 was 400,000 bbl. of oil, but actually daily production fluctuated widely during the year. At the beginning of 1940 daily production was approximately 330,000 bbl. During the first hali of the year it in-creased irregularly to the peak in June mentioned above and as the prolific Devonian producing areas were drilled up, the state's daily production declined rapidly during July and continued to decline, although more slowly, until the end of the year, when the daily production was approximately 325,000 bbl. The daily average production per well in the new fields at the end of the year was approximately 40 bbl. (Fig. I). Oil from the Devonian was also produced in the Bartelso field, Clinton County, the Sandoval field, Marion County, and the Irvington field, Washington County, bringing the estimated total production from the Devonian limestone to about 26 per cent of the state's total production, The remainder was obtained largely from the Mississippian system. About 2 per cent of the total was from Pennsylvanian and Ordovician strata. The decline in the Devonian limestone production has been so rapid that the 1941 output from this system will probably be only a small fraction of that of 1940 unless large new reserves are discovered. The "Trenton" (Ordovician) limestone has been tested in two wells in the Centralia field and both were small oil producers at a depth of about 4000 it. The "Trenton" also was found productive in the Salem field at a depth of 4500 ft. (Table 5). The initial production of the discovery well, which was completed shortly after the end of the year, was 130 bbl. on pump. Other wells drilled early in 1941 had initial productions averaging 172 barrels. The outlook for 1941 is for a continuation of drilling activity in Illinois, but at a declining rate (Fig. I, upper curve). The most active area at the end of 1940 was in the deep basin area in Wabash, Edwards, White, and Hamilton Counties.

Jan 1, 1941

By H. W. Hitzrot

THE new 4800-ton fine-grinding plant at the Hollinger Consolidated Gold Mines property at Timmins, in the Porcupine district of northern Ontario, went into operation in November 1937, and represents the culmination of an experimental program. The plant is a moderately low rectangular building of hollow tile on a steel frame, large enough to house four 7 by 15-ft. ball mills, with a 12 by 27-ft. classifier beside each mill. At one end is space for the addition of another mill and classifier or a mill and classifier for the regrinding of table concentrates. This regrinding is now done in the old grinding department of the main mill building. Also within the new building are the four 6-in. sand pumps for lifting the product from the low-dis- charge ball mills up to the classifier feed launders and the containers and appurtenances of a complete dust-collecting system. Together with the usual overhead crane, these constitute the major units of equipment within the new plant. The location is at the lower end of the main mill buildings toward the old tailings pond, now so neatly leveled off and sodded to rival the very best of our own W.P.A. projects. Close by the new grinding plant is a large dome-shaped structure-the new fine-ore bin designed arid built by Mr. Longmore and the Hollinger milling and engineering staffs. There are four separate automatically loaded inclined belt conveyors leading up from the bottom of the bin to the grinding plant. Each belt is equipped with a recording weightometer, in the grinding building. The whole structure and the machinery within it give the impression of permanence and a carefully integrated design with close attention to details, giving the operators every advantage for consistently good work. The many ideas and opinions behind this achievement were all ably organized and executed by the Hollinger milling and engineering staffs, anti not a few were directly initiated by them. Excellent cooperation was afforded by the Hollinger staff to the engineers helping to conduct the grinding and classification test program. It was the author's privilege

Jan 1, 1939

By R. K. McGeary, B. Lustman

Orientation relationships and rates of annealing of 97 pct cold rolled zirconium have been studied by X-ray techniques, metallography, and by hardness measurements. The process of annealing occurring by the formation of domains, and their subsequent growth without recrystallization, is demonstrated. NUMEROUS investigators1-' have revealed sub-grain formation after annealing cold worked metal single crystals and have generally described the results in terms of a dislocation mechanism of polygonization.5,6 in heavily cold rolled polycrystal-line aluminum the first stages of heating cause an apparently spontaneous subdivision of regions of the deformed matrix into a great number of slightly disoriented domains followed or accompanied by rapid growth of certain domains to form a recrystallization texture.7,8 In the present investigation the isothermal rate of annealing of cold worked polycrystalline zirconium has been studied by X-ray techniques, metallography, and by hardness measurement. It will be shown that, rather than by the usual nucleation and growth mechanism,"12 the process of annealing can best be explained by the formation of domains early in the annealing treatment and the subsequent growth of these domains without recrystallization. Experimental Procedure All the experimental work was performed on an arc-melted ingot of high purity zirconium crystal bar made by Westinghouse in a production scale deBoer unit. The weight percentage of impurities in the zirconium were as follows: C, 0.04; Fe, 0.05; Hf, 0.014; W, 0.01; Ti, Ni, and Al, 0.003; Si and N, 0.002; Cr and Cu, 0.001. Metallographically the zirconium showed only a single phase. The 4 in. diarn ingot was forged at 760°C to a 1 1/2x3 in. plate and was then rolled at 760°C to 0.150 in. thickness and annealed at this temperature for 20 min to produce an equiaxed grain structure of about 0.1 mm average grain diameter. The hot rolled plate was roller-leveled, surface ground to 0.135 in., cold rolled 83 pct reduction in thickness on a two-high mill, and then to a total reduction of 97 pct on a Sendzimir mill. The 0.004 in. strip material so produced received no subsequent mechanical treatment. Specimens % in. square were sheared from the rolled strip and isothermally annealed at 104 mm Hg in an all glass vacuum system equipped with a Vycor furnace tube. The temperature data presented are the average temperatures during the runs and did not vary more than about k3"C. X-ray Diffraction Methods: When zirconium is drastically cold rolled, a high degree of preferred orientation results in which prism poles, {1010}, are perpendicular to the rolling direction. After fully annealing this material an entirely new texture develops which corresponds to a 20" or 40" rotation of the deformation texture about hexagonal axes of

Jan 1, 1954

The paper will review the marked upsurge in the installation of new continuous metal coating lines, both hot dip and electrodeposition. Although some of this new capacity has been replacement for obsolete facilities or directed at traditional markets, eg building products, consumer durables etc, by far the major portion is targeted at the automotive industry. The reasons for the rapid growth of coated automobile panels are discussed. A comparison of the installed capacity with projections for this market indicate that a severe over-supply situation has arisen. Many coatings are now available for the automotive industry, each with their own strengths and weaknesses, but none as yet wholly satisfactory. Coating development has mainly been cost driven. This favours hot dipped coatings, providing surface quality and pressing problems can be overcome. The high cost per unit thickness of electrodeposited coatings has also seen pure zinc coatings being replaced by thinner, more corrosion resistant alloy coatings such as zinc-nickel and zinc-iron. Recently resin overlays have been introduced to improve the performance of electrodeposited coatings. Developments in coatings for the more traditional markets will be described. The fastest growing market in the last decade has been prepainted product for the building industry. This has led to the installation of extra painting capacity and again it appears an excess capacity situation has occurred. Over the same period the traditional zinc coatings have continued to lose market share to the zinc/aluminium alloy coatings, Galvalume and Galfan. These have been joined recently by '1'aiyo Crack-Free which has been taken up by some metal coaters. Galvalume is now widely accepted as being the best available coating for unpainted applications. It is also suggested that 'spin-off' coatings from automotive developments might find a niche in the consumer durable market. The end users of coated products, particularly the automotive industry, have demanded improvements in quality, such as surface smoothness, formability, etc. At the same time the new coating lines have to process wider strip and run at faster speeds. To reconcile these somewhat incompatible needs has required numerous process improvements, many of which need in-line instrumentation and computer control. The more important of these changes are discussed briefly. Finally the paper will describe the recent developments which have occurred in continuous galvanising in Australia and put them into context with the rest of the world.

Jan 1, 1993

By K. R. Van Horn, L. W. Kempf

Plastic deformation of most commercia1 metals within a sufficiently low temperature range results in profound changes in structure and properties, of which the causes and effects are not completely understood. One of these effects is the presence of internal residual stresses and strains, which ordinarily do not appear to require specific consideration in most structural applications but which may be quite undesirable in particular instances. For example, in heavy sections that require considerable machining before assembly, residual stresses may be undesirable because of the distortion they cause when their balance is disturbed by machining or otherwise. In addition, the distribution of stresses may be such that it acts in the same direction as the applied load, thus bringing about premature failure or reducing the load-carrying capacity of the member. One source of residual stress in metal structures is the plastic deformation that may occur during rapid cooling from relatively elevated temperatures, as in the cooling of a casting in the mold or the quenching of a heavy section from elevated temperatures during heat-treatment. These residual stresses are usually undesirable because their direction of operation and magnitude cannot be controlled well enough to permit utilization of the changes in properties of the metal that they may bring about. The most convenient manner of controlling such residual stress is by proper selection of the cooling rate or by reheating to a temperature at which plastic flow can take place, resulting in relief of the residual stresses and strains. Both of these methods of control, however, may cause a reduction in the optimum properties obtainable from the previous operation. A compromise must be struck, and if it is to result in the best possible combinations of properties, specific information must be available regarding the magnitude of the stresses and the rate at which they are affected by variations in cooling rate or in reheating temperature. The complete quantitative estimation of residual stress in complicated metal shapes is exceedingly difficult, if not impossible. In simple sections, however, relatively quantitative analysis may be applied and useful cstimations of stress distribution may be made. This paper is concerned largely with the rate of relief, upon reheating, of internal residual stress in simple aluminum-alloy structures. Since even with simple structures quantitative estimation of residual stresses is laborious and costly, an attempt was made to find other means of collecting data upon which commercial heat-treatments might be based. Incidentally, a few data were collected bearing on the problem of relaxation of aluminum alloys. Determination of Residual Stresses The magnitude and distribution of residual stresses in simple aluminum-alloy shapes rapidly cooled from elevated temperatures has been discussed in a previous paper.' Fig. I reproduces some of the data

Jan 1, 1942

By L. W. Kempf, K. R. Van Horn

Plastic deformation of most commercia1 metals within a sufficiently low temperature range results in profound changes in structure and properties, of which the causes and effects are not completely understood. One of these effects is the presence of internal residual stresses and strains, which ordinarily do not appear to require specific consideration in most structural applications but which may be quite undesirable in particular instances. For example, in heavy sections that require considerable machining before assembly, residual stresses may be undesirable because of the distortion they cause when their balance is disturbed by machining or otherwise. In addition, the distribution of stresses may be such that it acts in the same direction as the applied load, thus bringing about premature failure or reducing the load-carrying capacity of the member. One source of residual stress in metal structures is the plastic deformation that may occur during rapid cooling from relatively elevated temperatures, as in the cooling of a casting in the mold or the quenching of a heavy section from elevated temperatures during heat-treatment. These residual stresses are usually undesirable because their direction of operation and magnitude cannot be controlled well enough to permit utilization of the changes in properties of the metal that they may bring about. The most convenient manner of controlling such residual stress is by proper selection of the cooling rate or by reheating to a temperature at which plastic flow can take place, resulting in relief of the residual stresses and strains. Both of these methods of control, however, may cause a reduction in the optimum properties obtainable from the previous operation. A compromise must be struck, and if it is to result in the best possible combinations of properties, specific information must be available regarding the magnitude of the stresses and the rate at which they are affected by variations in cooling rate or in reheating temperature. The complete quantitative estimation of residual stress in complicated metal shapes is exceedingly difficult, if not impossible. In simple sections, however, relatively quantitative analysis may be applied and useful cstimations of stress distribution may be made. This paper is concerned largely with the rate of relief, upon reheating, of internal residual stress in simple aluminum-alloy structures. Since even with simple structures quantitative estimation of residual stresses is laborious and costly, an attempt was made to find other means of collecting data upon which commercial heat-treatments might be based. Incidentally, a few data were collected bearing on the problem of relaxation of aluminum alloys. Determination of Residual Stresses The magnitude and distribution of residual stresses in simple aluminum-alloy shapes rapidly cooled from elevated temperatures has been discussed in a previous paper.' Fig. I reproduces some of the data

Jan 1, 1942

By L. M. Barker, E. G. Lewis

THE literature of milling is replete with papers devoted to the subject of ball milling, all of which no doubt have contributed in one way or another to progress in that art. In this paper reference will be made to only a few of the many authors, but the value of the contributions of all who have written on that subject is hereby acknowledged. With a few exceptions the efforts of most students of the subject have been devoted to laboratory investigations of principles. Davis1 was one of the first to report on plant-scale investigations and to present to mill men certain criteria for the guidance of ball-milling practices. His conclusions with respect to the significance of sizing analyses of classifier sands in their relation to the factors of mill speed and ball sizing are particularly referred to. Those conclusions were: I. If the balls are large or the speed of the mill is high, crowding will appear at the finer sizes in the classifier sands. 2. If the balls are small or the speed is low, crowding will appear at the coarser sizes in the classifier sands. 3. The indications are that best efficiency is obtained when the screen analysis of the sands show a minimum crowding at any size. The last conclusion was qualified by the statement that it had not been proved conclusively. It is surprising, however, that the literature of later years reveals little evidence that millmen have made any serious attempt to apply those criteria. This may, perhaps, be explained by the fact that the average plant-scale ball-milling problem presents so many variables that an investigation of any one of them encounters the problem of control of the others-a problem that often is unsurmountable in a small plant. In a large plant, in which there is a duplication of grinding units in parallel operation, opportunity may be afforded for determining the value of such criteria. Nevertheless, a study of published data from grinding circuits of both large and small plants suggests that either Davis' criteria have been tried and found inapplicable or have never been given consideration. For the purpose of testing Davis' conclusions and with improvement of ball-milling efficiency as the final objective, a test program was initiated in the concentrator of the New Cornelia branch of the Phelps Dodge Corporation early in 1938. The practices of that plant have already been described .2 The fine-grinding units are arranged so that any one of eight units may be operated as a test unite and its results compared with those of the remaining units. All units receive similar feed from a common storage bin, in which the product of the fine-crushing plant is bedded by traveling tripper. The ball mills are all similar in size and operated at the same speeds, and are individually metered. The feeder conveyors of each unit are equipped with Merrick weightometers. The test program as initially outlined proposed investigation of the following:

Jan 1, 1941