Search Documents

By John F. Elliott, Robert D. Pehlke

The rate of reaction of nitrogen with liquid iron and with binary alloys of iron and Al, Cb, Cr, Ni, O, S, Si, and W were measured. The surface active elements, oxygen and sulfur, decrease the rate markedly. The other alloying elements have very little effect on the rate except when they function as deoxidizers, The rates of absorption and de-sorption were found to be equal. Several possible reaction mechanisms which may control the rate are considered. In order to describe completely the behavior of nitrogen in steelmaking processes, the mechanisms of mass transfer between the gaseous and liquid phases, nitrogen and iron, respectively, must be understood. A kinetic study to determine the nature of these mass transfer processes was undertaken, and the results of that investigation are presented in this paper. Specifically, the study was directed toward determining the influence of alloying elements on the rates at which pure nitrogen gas at constant pressure is absorbed and desorbed by liquid iron solutions: A previous paper1 reported measurements of the equilibrium solubility of nitrogen in liquid binary iron alloys. The experimental data are presented and discussed first and then several possible rate limiting mechanisms are considered. PREVIOUS RESEARCH The results of several investigations on the rate of absorption of nitrogen by liquid iron and iron alloys have been reported.2-14 There is little agreement on the rate coefficients among these studies because of the influence of geometry on the experimental system and of the purity of the liquid iron. The rate was found to be influenced by alloying content for the binary liquid iron systems: Fe-Al,2 Fe-C,4,6 Fe-Cr,4,5,8 Fe-Mn,5 Fe-Ni,5,8 Fe-O,9,10 Fe-O,9,10 and Fe-Si.2,6,7,11 Several investigators12"15 have reported that the rate of nitrogen absorption is increased in a reducing gas mixture and decreased in an oxidizing atmosphere. A mechanism for the retardation by oxygen of the absorption of nitrogen has been described by Naeser18 as the formation of an iron oxide film at the gas-metal interface. The film slows the absorption rate until it disolves in the metal, thus permitting nitrogen to enter the liquid iron. Karwat17 discussed the influence of oxygen in terms of the formation of gaseous molecules of nitrous oxide which represent a higher energy form than the nitrogen and oxygen or the oxidizing gas and consequently constitute an energy barrier for the process. Fischer and Hoffmann10 showed that the oxygen markedly reduces the rate of absorption of nitrogen, the rate constant being one order of magnitude smaller in liquid iron containing 0.15 to 0.24 pct 0 as compared to that in melts containing 0.001 to 0.02 pct 0. Although Chipman and Murphy2 reported that the rate of absorption of nitrogen in liquid iron was essentially independent of temperature, Eklund3 found that the rate increases strongly with increasing temperature as did Kootz4 and Saito.5,6 Karnaukhov and Morozov7 also reported a large temperature coefficient, but related it to increased stirring at higher power inputs in an inductively heated system. All of the authors above have treated their results assuming that the reaction is diffusion controlled, that the surface reaction is in equilibrium with nitrogen gas, and that a "first order" reaction takes place. Karnaukhov and Morozov7 and Humbert; who studied the rate of absorption in a closed system by observing pressure changes in the system as a function of time, concluded that their results best fit a diffusion-type analysis. This was further verified by von Bogdandy, Dick, and stranski18 and Fischer and Hoffmann10 who found the initial rate of

Jan 1, 1963

By Henry C. Meeves

The Bureau of Mines, between 1956 and 1963, examined 18 major pegmatite districts in Arizona, Colorado, New Mexico, South Dakota, Utah, and Wyoming to evaluate their content of beryllium, a material in short domestic supply that has become increasingly important to modern industry. This examination report includes the salient statistics on the production of pegmatite minerals other than quartz and feldspar; and brief descriptions of 170 specific pegmatite deposits.

Jan 1, 1966

By F. M. Lewis, J. F. Meyers

In the mining and handling of sulphide ores, some degree of oxidation takes place on the sulphide surfaces, which are exposed to the atmosphere. It is, moreover, well known that the oxidation compounds formed are a factor when such ores are subsequently treated by flotation. Modern operating technique and reagents are capable of contending with this condition to a major degree, provided that the proportions of the reagents used are varied correctly. This is particularly true at the Tennessee Copper Co., where the ore treated contains pyrrhotite in addition to other sulphides. A number of soluble salts, some of which are unstable, can be formed during the oxidation of the sulphide ores. Those unstable salts, whose oxygen requirements are unsatisfied, are constantly changing to more stable forms because oxygen reacts with them during the crushing, grinding and other operations of ore preparation. We add no chemicals of any kid to the ore pulp in its preparation for flotation feed. Consequently the only compounds that are present in the flotation feed are those produced by the natural oxidation of the ore in the presence of air and water. The Tennessee Copper Co. ore is composed of from 60 to 70 per cent sulphides and from 40 to 30 per cent non-sulphide material. It is not the purpose of this paper to discuss the nature of these various oxygen-sulphur compounds nor their effect on flotation, but to describe a method for correcting the effect. Suffice it to say that we have found that the reducing sulphur and oxygen salts have a depressing action on our bulk flotation process.' From long experience we find that the best means of correcting for this variation in our work is to increase or decrease the quantity of xanthate, the promoting agent, as the quantity of the reducing salts increases or decreases. It was, therefore, very desirable to provide the operators with some quick and

Jan 1, 1947

By Barbara Peszko, Tadeusz Tumidajski

"Various methods are used to identify the grain composition of fine-grained materials because so far the best notion of the grain size has not found and there is no single method to define grain size. In practice the most important are the following grain sizes: sieve diameter dt, effective diameter de, substitute diameter d2 and statistical diameter dst. The mentioned sizes are connected with the methods of analyses. Methods are correct but measure of different diameters of grain and their results are different.The most important methods of granulometric composition analyses are the following: the sieve analysis, the sedimentation method and the conductometric (Coulter-Counter) methods. In each of these methods various physical features connected with the grain size are measured.Sizes of grains defined by different formulas or measurement methods are associated mutually by dependencies, which are results of differences in their determination or calculation ways.In order to determine principles of results comparison the classification analysis results on linearly or non-linearly connected was made. Analyses which results demonstrate the same type of grain size distribution are treated as linearly connected. It is based on the general formulae which determines the probability density function of random variable which is the function of another random variable having the known density function.In order to show the difference in the grain composition of the same material qualified by different methods, three methods of investigations were distinguished. They are: the sieve analysis performed on precise sieves, the sedimentation analysis performed by means of a sedimentation balance “Sartorius” and the microscopic analysis performed after preparing a microscopic slide where the grain size was measured by the Martin’s method.The materials selected for the analysis were quartzite and glass, which are the material of high purity.The obtained results of mentioned above three types of analyses were approximated by distribution function of four distributions: Weibull, log-normal, cut Weibull and Gaudin-Schuhman."

Jan 1, 2003

By J. F. Myers, F. M. Lewis

IN the mining and handling of sulphide ores, some degree of oxidation takes place on the sulphide surfaces, which are exposed to the atmosphere. It is, moreover, well known that the oxidation compounds formed are a factor when such ores are subsequently treated by flotation. Modern operating technique and reagents are capable of contending with this condition to a major degree, provided that the proportions of the reagents used are varied correctly. This is particularly true at the Tennessee Copper Co., where the ore treated contains pyrrhotite in addition to other sulphides. A number of soluble salts, some of which are unstable, can be formed during the oxidation of the sulphide ores. Those unstable salts, whose oxygen requirements are unsatisfied, are constantly changing to more stable forms because oxygen reacts with them during the crushing, grinding and other operations of ore preparation. We add no chemicals of any kind to the ore pulp in its preparation for flotation feed. Consequently the only compounds that are present in the flotation feed are those produced by the natural oxidation of the ore in the presence of air and water. The Tennessee Copper Co. ore is composed of from 60 to 70 per cent sulphides and from 40 to 30 per cent nonsulphide material. It is not the purpose of this paper to discuss the nature of these various oxygensulphur compounds nor their effect on flotation, but to describe a method for [ ] correcting the effect. Suffice it to say that we have found that the reducing sulphur and oxygen salts have a depressing action on our bulk flotation process.1 From long experience we find that the best means of correcting for this variation in our work is to increase or decrease the quantity of xanthate, the promoting agent, as the quantity of the reducing salts increases or decreases. It was, therefore, very desirable to provide the operators with some quick and

Jan 1, 1946

By F. M. Lewis, J. F. Meyers

In the mining and handling of sulphide ores, some degree of oxidation takes place on the sulphide surfaces, which are exposed to the atmosphere. It is, moreover, well known that the oxidation compounds formed are a factor when such ores are subsequently treated by flotation. Modern operating technique and reagents are capable of contending with this condition to a major degree, provided that the proportions of the reagents used are varied correctly. This is particularly true at the Tennessee Copper Co., where the ore treated contains pyrrhotite in addition to other sulphides. A number of soluble salts, some of which are unstable, can be formed during the oxidation of the sulphide ores. Those unstable salts, whose oxygen requirements are unsatisfied, are constantly changing to more stable forms because oxygen reacts with them during the crushing, grinding and other operations of ore preparation. We add no chemicals of any kid to the ore pulp in its preparation for flotation feed. Consequently the only compounds that are present in the flotation feed are those produced by the natural oxidation of the ore in the presence of air and water. The Tennessee Copper Co. ore is composed of from 60 to 70 per cent sulphides and from 40 to 30 per cent non-sulphide material. It is not the purpose of this paper to discuss the nature of these various oxygen-sulphur compounds nor their effect on flotation, but to describe a method for correcting the effect. Suffice it to say that we have found that the reducing sulphur and oxygen salts have a depressing action on our bulk flotation process.' From long experience we find that the best means of correcting for this variation in our work is to increase or decrease the quantity of xanthate, the promoting agent, as the quantity of the reducing salts increases or decreases. It was, therefore, very desirable to provide the operators with some quick and

Jan 1, 1947

By Jacob T. Wainwright

This stove has been designed to meet the requirements of a fur nave that must be operated with either a reducing or a neutral flame ; and more particularly to make feasible the operating of re duction-furnaces with the cheaper grades of gas-fuel, which has heretofore been impracticable. In general, cheap gas-fuels result from incomplete combustion, and, being suited for further combustion, answer very well for heat ing purposes; and high temperatures may be attained with them, when they are used in conjunction with regenerative stoves. But, in operating a reduction-furnace, a high temperature is not the only requirement. It is also necessary that the fuel shall not be cansumed beyond a certain degree, in order to insure a re ducing flame for the reduction-process ; consequently, it becomes necessary to dispense with combustion as much as possible previous to the use of the fuel-gases in the reduction-furnace. Moreover, these gases must be preheated to a high degree, in order that a sufficient temperature may be maintained in the furnace; and, since this preheating cannot be accomplished by a previous, partial combustion of the gases themselves, it follows that the stoves for pre heating these gases should be heated to as high degree as it is pos sible to attain with an inferior fuel. This result can best be accom plished by complete combustion of the heating gases, and is further facilitated by preheating all of the air and gas used for this com plete combustion. It is more particularly desirable to preheat the air, since the combustible gases used may generally be obtained directly from the furnace, or gas-producer. The reducing gases, escaping from a gas-fuel reduction-furnace, are capable of considerable further dilution with air to secure com plete combustion, and consequently may be utilized for heating the stove to a high temperature, provided the air be sufficiently preheated.

Jan 1, 1889

By E. J. Bruderlin

A metallurgical process to be economically successful must be carried on under proper conditions of control and equipment. The question of equipment is always of primary importance. In the distillation process for the recovery of zinc by retorting, the retort is the all-important piece of equipment. Each retort in a working blóck must function as a separate unit. Over-all block efficiency is the result of the ability of the individual retort to withstand the severe conditions of operation for a maximum period of time. Therefore retort manufacture has been an ever present problem with the operator of a zinc-retorting plant. During recent years the zinc-plant operator has been faced with rapid changes in the character of the ores and concentrates. Operating costs have increased as a result of the introduction of the flotation process and the amount of flotation concentrates to be handled. To counteract increasing costs, the operator has found it necessary continually to attempt heavier loading of retorts, until a 45 to 50-lb. charge per cubic foot of retort space has become common practice. Heavy loading has brought about severe firing conditions, which, in turn, have emphasized the necessity for further improving the quality of the retort. Increasing percentages of detrimental impurities in the retort charges have also added to the operator's difficulties. Amarillo Silicon Carbide Retorts At the Amarillo plant of the American Smelting and Refining Co. a retort made of a suitable plastic clay grogged with silicon carbide has been found to best meet the present-day requirements. Retorts of this kind have been in use at Amarillo for 8 years and have shown an average furnace life of approximately 175 calendar days. The Amarillo retort is cylindrical in shape and after burning is approximately 83/4 in, inside diameter by 60 in. over-all length. The wall thickness is 136 in., except for the butt of the retort, which is approximately 2½ in. thick. The retort mud has a shrinkage of 3 per cent, or approximately % in. per foot. The silicon carbide retort after being properly dried weighs about 211 lb. When the retort is fired and ready to go into use the weight decreases to approximately 203 lb.

Jan 1, 1937

By Peter J. Szabo

The mining executive works in a cyclical industry. His employment is subject to the vagaries of the marketplace. Boom and bust has always been the industry's story. "Big oil" failed in its mining effort. This left emotional and financial scars on many mining families. One must remember that mining executives always play a high-stakes game. Given the cyclical nature of the mining industry, mining executives need to take care of their own financial security. The mining executive that does not plan for his financial security in this cyclical business is playing Russian Roulette with his future. Take a look at those people who have reached their later years with the mining industry. One usually finds three categories of people. Those few in the first group have been fortunate enough to have worked for one company. They have survived the winnowing process of cyclicality, political problems, and takeovers. They have reached normal retirement age. For them, the retirement years are usually comfortable. People in the second group have worked for those same mining companies. But these people have been forced out by early retirement. Or they have been laid off for cyclical, takeover, or political reasons. The third group includes those who have held many positions in the mining industry. Probably not until their later years are they fully vested, if at all, in a pension program. The first small group, then, is the exception. The others, unless they have taken care of their financial security, are doomed to later years of financial problems, stress, and unhappiness. Too late in life, many realize the harsh realities of failure to plan and implement a personal financial program. Mining executives go to some of the world's leading mining schools, to learn how to make money. The curriculum is technically strong. Most mining graduates are familiar with the intricacies of discounted cash flow, present value, and the Hoskold formula. But few of these same mining schools require courses on personal financial planning. Such courses could give mining students a realistic foundation and the mechanisms with which to cope with their cyclical profession. An executive has only three sources of money. He can make money at work. He can put his money to work. Or he can get money from charities, such as government programs. Of these three sources of money, money at work has the best chance of providing financial security in later years. The mining executive must think of the day when he will be too old to work and contribute to the market place. At this point, the quantity and quality of his investments will determine whether his later years will be secure. Along with the Mining Engineering Handbook, two key books should be included in the mining executive's library. These are Venita Van Caspel's The Power of Money Dynamics and Benjamin J. Stein's Financial Passages. These books contain the basic concepts of personal financial planning so critical to an individual's financial survival. Venita points out the simple formula that is the key to financial independence: Time + Money + American Free Enterprise (Rate of Return) = Opportunity to Become Financially Independent Chart 1 shows that this is not a trite formula. The chart shows the dramatic effects of compounding over time. The chart also shows at various yields what a $2000 a year Individual Retirement Account (IRA) contribution will accumulate. Chart 1 (from Money magazine) is based on the future value of an ordinary annuity. It shows that the key to amassing a small fortune by the time a person reaches his 50s is starting to save methodically in his 20s. This, coupled with the highest yields consistent with safety of principal will ensure financial security. There are significant effects from compounding money over time. Every year the decision is put off to save for later years will cost a person dearly by the time he reaches his 50s. For example, consider the decision to put off for one year a $2000 IRA investment at a 12% return. Starting it at age 31 instead of 30 will cost the executive almost $100,000 by age 65. What if the executive waits until age 35 to get started with his $2000 a year investment? He will then lose nearly $400,000 by age 65. Stated another way, the executive costs himself this $400,000 simply because he did not invest $167 a month for five years. $167 a month - that's less than an inexpensive second car payment. This $400,000 pool of money could provide the executive a $40,000 a year income at age 65, assuming a 10% return on invest-

Jan 11, 1985

By John C. McDonald

The amount of published literature in the field of mechanical properties of magnesium alloys is not great; particularly with respect to rolled alloys. Haughton and Prytherchl have summarized most of the articles to 1937, including their own work on sheet. Although many papers can be found dealing with the technology of magnesium and the alloys now in commercial use, there does not seem to be any work dealing exclusively with the variation in properties of rolled alloys as caused by changes in alloy composition. Comparison of published data reveals considerable discrepancies in properties of alloys of the same composition, probably due to differences in the details of working and heat-treating followed by different workers. The purpose of this paper is to study the properties of alloys in conditions where the effects of such differences have been eliminated. It is well known that the strength and ductility of metals are functions of the working and heat-treating they have received, as well as of their chemical composition. In comparing alloys with respect to these properties, therefore, all possible combinations of the variables of the fabrication procedure ought to be carried out on each alloy. One or more of these treatments mill produce the highest ductility, or strength, or both. These highest properties would then be selected as characteristic of each alloy, and alloys would be compared on the basis of those properties. Thus a separation of the effect of composition and that of workiiig and heat-treating would be achieved. In this paper, however, a compromise with completeness has been made by carrying out a restricted number of treatments. As a consequence, the properties obtained are not necessarily the best that the alloy is capable of exhibiting; but since all alloy3 have been treated by the same method, the results ought to be comparable. The elements selected for the study comprise a class that will alloy easily with magnesium, and that are reblatively cheap. Each was added in different amounts, up to a limit that varied with the element.

Jan 1, 1940

By John C. McDonald

The amount of published literature in the field of mechanical properties of magnesium alloys is not great; particularly with respect to rolled alloys. Haughton and Prytherchl have summarized most of the articles to 1937, including their own work on sheet. Although many papers can be found dealing with the technology of magnesium and the alloys now in commercial use, there does not seem to be any work dealing exclusively with the variation in properties of rolled alloys as caused by changes in alloy composition. Comparison of published data reveals considerable discrepancies in properties of alloys of the same composition, probably due to differences in the details of working and heat-treating followed by different workers. The purpose of this paper is to study the properties of alloys in conditions where the effects of such differences have been eliminated. It is well known that the strength and ductility of metals are functions of the working and heat-treating they have received, as well as of their chemical composition. In comparing alloys with respect to these properties, therefore, all possible combinations of the variables of the fabrication procedure ought to be carried out on each alloy. One or more of these treatments mill produce the highest ductility, or strength, or both. These highest properties would then be selected as characteristic of each alloy, and alloys would be compared on the basis of those properties. Thus a separation of the effect of composition and that of workiiig and heat-treating would be achieved. In this paper, however, a compromise with completeness has been made by carrying out a restricted number of treatments. As a consequence, the properties obtained are not necessarily the best that the alloy is capable of exhibiting; but since all alloy3 have been treated by the same method, the results ought to be comparable. The elements selected for the study comprise a class that will alloy easily with magnesium, and that are reblatively cheap. Each was added in different amounts, up to a limit that varied with the element.

Jan 1, 1940

The condition of the domestic mining industry is obviously affected by the cycles in general business conditions. This study, the results of which are presented in a series of 78 charts, attempts to examine the interrelationships between the general business indicators and the major statistical measures for the base-metals industries during the cycles in the United States economy following World War II. For these industries the cyclical problem is perhaps less acute than the secular-trend problem. However, short-run fluctuations in production and employment do have very important impacts upon the welfare of the regions which derive a significant portion of their income from base-metals mining and processing industries. Any information concerning the normal patterns of development as the industries enter into a cyclical recession will permit better forecasts and perhaps help promote measures to alleviate the distress that occurs. Also, a systematic study of the comparative movements among the statistical measures during a series of cycles can bring to the fore the economic causation involved, and perhaps, after intensive study, can lead to a better method of short-range forecasting for these industries. This study has not fully achieved these aims. However, observations which significantly aid the interpretation of the current monthly statistics on these commodities are made, and some very general conclusions are drawn. The charts are presented so the interested people can examine them and draw additional conclusions. The charts refer specifically to cyclical analysis. The technique of indexing each cycle to its turning point effectively subordinates the longer term trend movements of the data. Thus, certain general conclusions flowing from this study and from the continuing economic research of the Office of Chief Economist will aid the reader by clarifying the frame of reference within which the charts should be examined.

Jan 1, 1961

By Dean F. Winchester, C. D. Johnson

The so-called Rocky Mountain region is here made to include Colorado, Idaho, Montana, northern New Mexico, Utah and Wyoming, an area of great distances and relatively sparse population. Conditions of distance, transportation and markets have had their retarding influence on devolopment and production but the increase in facilities and markets in recent years has provided additional incentive for more thorough search for new productive areas and the more complete development of the known fields. The low prices of crude during the past year have offset, to a certain extent, the desire for increased production and much of the effort has been directed therefore to outlining new areas rather than to attempts to increase production from known fields and thereby add to the already sufficient supply above ground. During the year just closed the Rocky Mountain region has seen consistent efforts to outline new areas and these efforts have been reasonably successful. In this area a very large part of the land is government property, and by cooperation between the government, the private owner and the company it has been possible to carry on development in a scientific manner, providing for the maximum recovery of valuable products at least cost and at times when prices were best. Due to the fact that in the Rocky Mountain region costs of exploration and development are relatively high because of natural circumstances, it has been the policy of operators to drill test wells only on structures where they controlled a large proportion of the land. Even community lease programs have been effected in certain areas, thus obviating the necessity of offset drilling and the attendant uneconomical and even wasteful production. Oil production in the Rocky Mountain states has shown a slight increase during the year, the average daily production for November being 78,124 bbl. as against an average in January of 76,681 bbl. The total production during the first 11 months of the year, according to the U. S. Burcau of Mines, was as follows:

Jan 1, 1929

Discussion of the paper of FRANCIS S. PEABODY, presented at the St. Louis meeting, October, 1917, and printed in Bulletin No. 125, May, 1917, pp. 775 to 781. THE CHAIRMAN (CARL SCHOLZ, Chicago, I11.).-Coal wastage is undoubtedly one of the most prominent topics before the coal operators of the United States today. Even those who have been in the business only 25 years, like myself, know that the exhaustion of coal is something that should and must, be curbed. If it is not, before long we shall discover that the great coal resources of the country are not what we-thought they were; we have been so accustomed to work at the best and thickest coal alone, that it will be difficult for us to realize one of these clays-and that (lay is not far distant-that we are no longer the rich nation in coal that we thought we. were. In this connection I feel obliged to attach a little blame to the Geological Survey for misleading the people. There are several members ,here who assisted in that work, and I am going to ask them to defend themselves. The Geological Survey deals with coal seams of much less thickness than we could now expect to, mine, particularly with the present high wages, excepting at a prohibitive cost. The Geological Survey, in its estimates, does not discriminate between thick and thin seams, but simply estimates our resources at so many hundred thousand billion tons of coal. I believe they include seams from 15 to 18 in thick, but you all know that a vein below 3.5 or 4 ft. is not considered economical to mine at this time. R. V. NORRIS, Wilkes-Barre, Pa.-Mr. Peabody has evidently been thinking almost entirely of Illinois conditions, with which I regret to say I am absolutely unfamiliar. In some West Virginia mines the total recovery at present is considerably over 90 per cent. and extraction-, as high as 97 or 98 per cent. are claimed.

Jan 1, 1918

By John Johnston

When I was honored by being invited to give the Howe Memorial Lecture, I decided to read Howe's book, "The Metallography of Steel and Cast Iron," published in I9I6—that is, about 25 years ago—in search of a text. I found the book written in fine, clear, attractive, yet precise style, as I expected, knowing that his father— Dr. Samuel Gridley Howe, his mother— Julia Ward Howe, and all of his four brothers and sisters had lived in a New England literary atmosphere and had written books. This leads me to suggest that many authors of metallurgical papers and books could well study Howe's writings with a view to the improvement of their own. I failed to find a specific text, but did find a subject, for in reading his book I was struck by the few instances in which time is considered explicitly as a factor in the phenomena examined, and by the fact that many of the hottest arguments would have been settled had time been taken properly into account. Indeed, Howe hardly mentions time except in a rather incidental way, as in a few references to lag; for instance: The lowering of temperature at which the transformation occurs by rapid cooling . . . is a phenomenon of undercooling or lag. It is in part explained by the fact that the transformation itself is a time-consuming reaction which, setting in during a rapid fall of temperature, is naturally protracted till the temperature has sunk far below that at which it is due. He does discuss, quite fully, the iron-clrbon equilibrium diagram, as known at that time, introducing it by stating: As he is a reasonable man who is not deterred from using a hand truck for moving his trunk by the consideration that he has thus to move a trunk plus a truck, so am I reasonable in putting into your hands this useful, indeed indispensable. tool for mastering the ABC of iron metallurgy. Somewhat later, in introducing a discussion of the phase rule, which "it would be hardly proper to pass ... by without an attempt to outline its meaning," for "a clear exposition of its applicability or jurisdiction is needed to restrain the half-initiated from misusing it and the uninitiated from being misled by these misuses," he writes—and I quote his statement because we cannot properly discuss the influence of time on a process until we know the state of equilibrium which would ultimately be reached by the system under consideration: It is a most remarkable and valuable generalization, its conceptions help greatly toward getting a broad outlook on metallography, but its misconception has brought out a flood of obscuring writings. it tells us about the constitution towards which alloys tend, that which they reach when equilibrium is complete, when all tendencies have corrected themselves and have been complied with completely. Its application, in absence of true equilibrium, is like determining density with a telescope or even with a tuning fork; it is like the mad tea party at which the butter put into the works of the watch was the best butter. If the reader learns no more than to beware of attempts to dccipher the conditions of inequilibrium by a law which touches only the conditions of exact

Jan 1, 1942

By John Johnston

When I was honored by being invited to give the Howe Memorial Lecture, I decided to read Howe's book, "The Metallography of Steel and Cast Iron," published in I9I6—that is, about 25 years ago—in search of a text. I found the book written in fine, clear, attractive, yet precise style, as I expected, knowing that his father— Dr. Samuel Gridley Howe, his mother— Julia Ward Howe, and all of his four brothers and sisters had lived in a New England literary atmosphere and had written books. This leads me to suggest that many authors of metallurgical papers and books could well study Howe's writings with a view to the improvement of their own. I failed to find a specific text, but did find a subject, for in reading his book I was struck by the few instances in which time is considered explicitly as a factor in the phenomena examined, and by the fact that many of the hottest arguments would have been settled had time been taken properly into account. Indeed, Howe hardly mentions time except in a rather incidental way, as in a few references to lag; for instance: The lowering of temperature at which the transformation occurs by rapid cooling . . . is a phenomenon of undercooling or lag. It is in part explained by the fact that the transformation itself is a time-consuming reaction which, setting in during a rapid fall of temperature, is naturally protracted till the temperature has sunk far below that at which it is due. He does discuss, quite fully, the iron-clrbon equilibrium diagram, as known at that time, introducing it by stating: As he is a reasonable man who is not deterred from using a hand truck for moving his trunk by the consideration that he has thus to move a trunk plus a truck, so am I reasonable in putting into your hands this useful, indeed indispensable. tool for mastering the ABC of iron metallurgy. Somewhat later, in introducing a discussion of the phase rule, which "it would be hardly proper to pass ... by without an attempt to outline its meaning," for "a clear exposition of its applicability or jurisdiction is needed to restrain the half-initiated from misusing it and the uninitiated from being misled by these misuses," he writes—and I quote his statement because we cannot properly discuss the influence of time on a process until we know the state of equilibrium which would ultimately be reached by the system under consideration: It is a most remarkable and valuable generalization, its conceptions help greatly toward getting a broad outlook on metallography, but its misconception has brought out a flood of obscuring writings. it tells us about the constitution towards which alloys tend, that which they reach when equilibrium is complete, when all tendencies have corrected themselves and have been complied with completely. Its application, in absence of true equilibrium, is like determining density with a telescope or even with a tuning fork; it is like the mad tea party at which the butter put into the works of the watch was the best butter. If the reader learns no more than to beware of attempts to dccipher the conditions of inequilibrium by a law which touches only the conditions of exact

Jan 1, 1942

By William R. Webster

The unusual interest taken in the papers on steel at the New York (1922) meeting showed that the time is ripe for the renewal of the general discussion of the physics of steel, on the same lines that wete used formerly and produced such good and lasting results. The curves shown in Figs. 1 to 4 and the appendix were added to my paper1 after the February meeting, but, unfortunately, Figs. 1 and 3 were transposed; the curves on page 252 are for bessemer steel and belong on page 254; while those on page 254 are for open-hearth steel and belong on page 252. These errors are evident at once on referring to the data in Tables 1 and 2, pages 227 and 228. The curves for each 0.05 per cent. of carbon and manganese in basic open-hearth steel are given in Figs. 1 and 2; these lines for the lower carbons and manganese are comparatively uniform. Figs. 3 and 4 give similar lines for carbon and manganese in bessemer steel. The large break in the carbon lines from 0.55 per cent. to 0.60 per cent. is caused by much higher silicon in the steels of 0.60 per cent, carbon and over that are used for springs, etc. The estimated ultimate strength of pure iron, and the increase in strength by carbon, phosphorus, and manganese, with the different views regarding the same, were given and diseussed. All of this can be considered as an introduction to the practical use that is now being made of such data in selecting the heats of steel best suited to give the required physical tests called for in the finished rolled material. The chemical composition of the steel, of course, tells only a part of the story, as many other factors that have an influence on the physical properties of the steel must be considered, and controlled as far as is possible. Some of these have already been referred to, but there are other important ones to be considered and discussed.

Jan 1, 1923

By William R. Webster

The unusual interest taken in the papers on steel at the New York (1922) meeting showed that the time is ripe for the renewal of the general discussion of the physics of steel, on the same lines that wete used formerly and produced such good and lasting results. The curves shown in Figs. 1 to 4 and the appendix were added to my paper1 after the February meeting, but, unfortunately, Figs. 1 and 3 were transposed; the curves on page 252 are for bessemer steel and belong on page 254; while those on page 254 are for open-hearth steel and belong on page 252. These errors are evident at once on referring to the data in Tables 1 and 2, pages 227 and 228. The curves for each 0.05 per cent. of carbon and manganese in basic open-hearth steel are given in Figs. 1 and 2; these lines for the lower carbons and manganese are comparatively uniform. Figs. 3 and 4 give similar lines for carbon and manganese in bessemer steel. The large break in the carbon lines from 0.55 per cent. to 0.60 per cent. is caused by much higher silicon in the steels of 0.60 per cent, carbon and over that are used for springs, etc. The estimated ultimate strength of pure iron, and the increase in strength by carbon, phosphorus, and manganese, with the different views regarding the same, were given and diseussed. All of this can be considered as an introduction to the practical use that is now being made of such data in selecting the heats of steel best suited to give the required physical tests called for in the finished rolled material. The chemical composition of the steel, of course, tells only a part of the story, as many other factors that have an influence on the physical properties of the steel must be considered, and controlled as far as is possible. Some of these have already been referred to, but there are other important ones to be considered and discussed.

Jan 1, 1923

By E. M. Norris

In the summer of 1917 it was decided to fireproof the main Tramway hoisting shaft of the Anaconda Copper Mining Co. at Butte, Mont. The shaft has three hoisting compartments and one pump compartment; it is timbered with 12 by 12-in. (30.5 by 30.5-cm.) fir timber, and is 2475 ft. (754 m.) deep. Subsidence and displacement of the surrounding country rock had produced exceedingly heavy ground, and had carried the shaft out of line, in several places, by as much as 2 ft. (0.6 m.) displacement. Constant repairing and realigning of the timbers had been necessary in order to maintain clearance for the cages. The most feasible method of fireproofing, therefore, seemed to be to cover the timbers with a coat of concrete applied with the cement gun. The cement gun, which is operated by compressed air at ordinary mine pressures, feeds a mixture of sand and cement through a hose to a nozzle having a water connection. The mortar in fluid form is thus sprayed upon the prepared surface in thin layers, which can be built up to any desired thickness. The cement gun can be set up at any convenient point; satisfactory results have been obtained with the nozzle a distance of 500 ft. (152 m.) from the gun. The shaft was thoroughly overhauled and the timbers put in the best possible state of repair. Between the 1000 and the 1400 levels, much loose ground lay against the shaft timbers on the north side; this was breast-boarded back and a 30-in. (76-cm.) reinforced-concrete retaining wall was erected, leaving a space of 12 in. (30.5 cm.) outside the shaft timbers to allow for future movements of the ground. For convenience in handling men and materials, it was arranged to concrete the auxiliary hoisting-cage compartment and the pump compartment first, using the cages of the main hoist to serve the cementing crews. The auxiliary cage was then available while the remainder of the shaft was being concreted. A tight partition of 2-in. (5.08-cm.) plank was erected between the auxiliary and the adjoining hoisting compartments, for better protection of men riding on the cages. The application of concrete made this

Jan 1, 1920

By Pol Duwez

The effect of the rate of cooling on titanium, zirconium, and thallium has been measured. For titanium-molybdenum alloys, it has been shown that for molybdenum concentration up to 8 pct the rate of cooling has no effect on the transformation temperature, but this temperature decreases progressively with increasing molybdenum content. HIGH strength to weight ratio and remarkable corrosion resistance have often been advanced as the main reasons for the present widespread interest in titanium. For the physical metallurgist, the existence of an allotropic transformation in titanium is another important factor. As in the case of iron, an allotropic transformation may be the fundamental property upon which the response of Ti-base alloys to heat treatment will depend. It is therefore important to study the mechanism of the allotropic transformation in pure titanium and the effect of alloying elements on this transformation. The existence of an allotropic transformation in titanium was reported in 1931 by Schulze.' Later, De Boer et al.' determined the transformation temperature from a discontinuity in the electrical resistivity at 882"42O°C. According to recent work," the transformation temperature is 882.5"&1°C. The crystal structure of the room temperature a phase is hexagonal close-packed and the high temperature fi phase is body-centered cubic.' It is well known that the high temperature /3 phase of pure titanium cannot be retained by quenching to room temperature. Several investigators'-' have shown that in alloys of titanium with metals which are soluble in the @ phase (for example, nickel, molybdenum, chromium, or manganese), the /3 structure can be retained, providing the concentration of the alloying element is greater than a certain critical value. Below this critical value, the alloys transform during quenching, at least partially, into a supersaturated solid solution having the a. structure. This behavior is very similar to that found in some iron binary alloys (Fe-Ni and Fe-Mh, for example) and is an indication that the transformation might occur by means of a shear mechanism analogous to that observed in the austenite-martensite reaction. The present investigation is mostly concerned with the effect of the rate of cooling on the /3 to a transformation. In the first portion of this paper, the results obtained on pure titanium are described. Two other pure metals, zirconium and thallium, were also investigated, because they both have an allotropic transformation like titanium, from an hexagonal close-packed to a body-centered cubic structure. For purposes of comparison, the effect of rate of cooling of the y to a transformation of iron was included in the experimental program. The second part of this paper deals with Ti-Mo alloys. The equilibrium phase boundaries involving the solid state reactions on the Ti-rich side of the system were determined and a study was made of the effect of the rate of cooling on the transformation of the high temperature /3 solid solution. Experimental Procedure Since the main object of the present investigation was the determination of the effect of the rate of cooling on a transformation temperature, the best technique available was that used by Greninger" in his study of the martensite arrest in carbon steels. This method consists of heating a very small sample of metal to which fine thermocouple wires are .attached, cooling the sample rapidly by means of a blast of helium, and recording the temperature vs. time curve on an oscillograph. The apparatus used in the present experiments was very similar to that described by Greninger, except that the heating coil was made of molybdenum wire (0.040 in. in diam) and the assembly was placed in a bell jar under vacuum of 10" mm Hg or less. The specimen con-

Jan 1, 1952