Search Documents

By J. Snowberger III

Rhenium is a valuable and extremely rare chemical element with unique chemical properties. It is extracted commercially as a byproduct from the processing of molybdenite associated with porphyry copper ores. There is a present interest in recovering rhenium from copper pregnant leach solutions (PLS) produced by copper heap and stockpile leaching. These solutions contain rhenium at very dilute concentrations, typically in the 1 mg/L concentration range. This paper describes laboratory column ion exchange experiments to extract rhenium from these solutions using weakly basic anion exchange resins and actual plant PLS from two operating mines. The dynamic loading and elution behavior of Re on Purolite® A170 and A172 is discussed.

Feb 23, 2014

By Patrick J. Hannigan, Seth Robertson, Rozbeh B. Moghaddam

The Top-Loaded Bi-Directional Test (―TLBT‖) and the conventional Bi-Directional Load Test (―BDLT‖) are full-scale static load test methods. In both methods, the test loads are applied bi-directionally to the deep foundation. The advantages of the conventional BDLT have been well established for cost efficient static load testing of deep foundations, particularly for large diameter, high-capacity drilled foundations. A conventional BDLT applies the bi-directional test loads using an embedded jack and bearing plates. The TLBT method also applies the bi-directional test load to embedded bearing plates but does so using reusable high-strength threaded bars attached to an above-grade hydraulic jack and load transfer assembly. The new TLBT method is well suited for load testing shafts of a moderate diameter, length, and nominal resistance or ultimate load. TLBT advantages include economic considerations resulting from the method’s reusable load application components and constructability considerations as it readily accommodates a center concrete tremie pipe or pump line location. This paper presents comparison results from full-scale load tests performed using both bi-directional load testing methods. Adjacent 3-foot diameter by 30-foot long BDLT and TLBT shafts were tested. Details regarding subsurface conditions and test shaft construction are included for the comparison of the TLBT and BDLT results. Corresponding test data and analyses for both test shafts are presented and discussed in detail. The BDLT shaft had a maximum uni-directional load of 240 kips at upper and lower bearing plate displacements of 0.5 and -3.8 inches, respectively. The TLBT had a maximum uni-directional load of 300 kips at upper and lower bearing plate displacements of 1.0 and -5.9 inches, respectively. These results as well as the load-transfer behavior and equivalent top loading curve results from the adjacent BDLT and TLBT drilled shafts are discussed. The paper also discusses the strain gage instrumentation on the TLBT load application bars and on the embedded bearing plates.

Oct 1, 2022

By Leonardo Sales Araujo

Ligas de zircônio encontram grande aplicação em componentes estruturais do núcleo de reatores nucleares, dadas suas vantagens como resistência mecânica e a corrosão e baixa seção de choque de nêutrons térmicos. Contudo, por se tratar de uma liga reativa e necessitar de homogeneidade química e microestrutural, requer processos de fusão especiais como refusão a arco em vácuo. No presente trabalho, foi produzido um lingote de liga de zircônio a partir de briquetes de zircônio esponja compactados e unidos por soldagem para a composição do eletrodo. Foram realizadas duas refusões para aumento do tamanho do lingote e aumento da sua limpeza. As duas fusões foram analisadas por meio de observação das variáveis de processo. Foi possivel corroborar a viabilidade do processo de fabricação do lingote de zircônio em duas etapas de refusão. A análise das variáveis de processo mostrou que a primeira etapa de refusão apresentou maior instabilidade durante a fusão, o que poderia afetar a estrutura de solidificação. Com isso, uma etapa de refusão foi realizada, com maior estabilidade, além de potencialmente propiciar maior grau de limpeza e homogeneidade da liga.

Aug 16, 2017

By N. Myung, G. Hwang, H. Kim, Y. Han, S. Choi

"According to research presently being conducted on selective lithium recovery in seawater, inorganic adsorbents with high selectivity and capacity for capturing lithium ions from liquid lithium resources are called lithium ion-sieves (LISs). Their low toxicity, low cost and high chemical stability make LISs suitable for lithium recovery from seawater. In the present study, the ultrathin LMO nanofibers with controlled diameter were successfully fabricated by an electrospinning technique with a hypothesis that greater aspect ratio (i.e., smaller diameter) would lead to the enhanced recovery of lithium ion from seawater. Design of Experiment (DOE) and dimensionless analysis were performed to systematically optimize the diameter and morphology of nanofibers. Several complementary techniques including FE-SEM and XRD were used to evaluate the physical/physicochemical properties of the nanofibers. Lastly, the lithium ion recovery was tested for the nanofibers with different physical properties using lithium ion solution. INTRODUCTION Demand for lithium resources is increasing in many industries across the world.1-2 However, the conventional resources for lithium is very limited, and it even gets worse to secure the resources due to low grade and/or complexity of feed materials. Much effort has been, therefore, devoted to obtaining lithium from aqueous lithium resources. Several methods such as solar evaporation3-4, co-precipitation5, and solvent extraction6 have been proposed for recovering lithium from an aqueous lithium source, but there are limitations on its use; It takes a very long time or conditions such as temperature, pH and Mg/Li ratio are severe. Lithium ion-sieve (LIS) materials are considered as a good lithium adsorbent because of their unique chemical structure that can selectively separate lithium ion from brine and seawater.7- 10 Furthermore, their low toxicity, low cost, and high chemical stability make LIS suitable for lithium recovery from aqueous lithium resources. Spinel hydrous manganese oxide (HMn2O4) derived from spinel lithium manganese oxide (LiMn2O4) after topotactically extracting lithium from the spinel structure by acid treatment is most widely investigated LIS.10, LIS materials have been actively studied in various forms for easy handling and high efficiency (i.e. membrane11,12, foam13-14, granular15,16). Among them, the 1-D nanostructure LIS with high specific surface area is excellent in efficiency.9 In this study, we present the part of our recently submitted work17. Specifically, we fabricated systemically lithium manganese oxide nanofibers with different diameter as a lithium ion adsorbent using electrospinning technique through design of experiment (DOE). Enhanced lithium ion adsorption properties of the HMn2O4 nanofibers with different diameter were investigated in lithium liquid resources."

Jan 1, 2018

By Alei Leite Alcantara Domingues

A microscopia óptica é uma ferramenta importante para o entendimento dos processos envolvidos na produção do minério de ferro e seus aglomerados. Nos laboratórios em que esse tipo de análise é feita, tem-se geralmente um microscópio de luz refletida e um operador treinado que leva diversas horas para concluir uma única amostra. Nesse trabalho serão mostrados exemplos de resultados de minérios de ferro, sínter e pelotas obtidos em um sistema de microscopia óptica automática com análise de imagens. No estudo do minério de ferro foram determinados a composição mineralógica quantitativa, morfologia das partículas e tamanho dos cristais. Na microscopia de sínter foram determinados a quantificação de fases, porosidade, textura, recristalização de hematita e morfologia das ferritas. Nas pelotas produzidas com minério de ferro foram feitas análises de quantificação de fases, distribuição e quantificação dos poros e evolução microestrutural dos grãos. A implantação de um sistema de microscopia óptica automática com análise de imagens permite que análises sejam feitas em menor tempo, com maior reprodutibilidade possibilitando que a técnica seja implantada em áreas de produção que exijam respostas mais rápidas.

Oct 30, 2017

By S. Hamm

Elevated total dissolved solids (TDS) content in waters downstream from surface coal mines in Central Appalachia is an increasing concern, as unnaturally high TDS and/or associated specific conductivity (SC) may contribute to deteriorated stream ecosystem health. The aim of this preliminary study was to explore the efficacy of accelerated leaching as a means of minimizing long-term TDS/SC generation by problematic overburden materials. Five spoil samples were collected and leached using simulated rainwater solutions under ambient and acidified pH conditions. SC and pH were monitored during each leach cycle, and ICP-MS was used to determine how leaching conditions affected release of specific ions. This paper highlights the results of both jar and column leaching tests. Among the most significant findings was that, for certain spoil materials, SC in leach column effluent was effectively reduced when spoil was leached first with acidic rainwater followed by ambient rainwater (vs. ambient rainwater leaching alone). This suggests that accelerated leaching might aid in long-term stabilization of some materials.

Feb 23, 2014

By Jacob L. Brinkman, Catherine E. Johnson

Unmanned aerial vehicles (UAVs) are being explored by researchers to measure concentrations of gas emissions in situations where such measurements are otherwise extremely difficult to obtain, such as NO and NO2 (NOx) emissions from surface mine blasting. Recently, countries have imposed or are planning to impose surface blasting gas pollution regulations, which creates a need for an improved understanding of UAV-based gas measuring systems. The experiments detailed in this paper were performed to determine if airflow generated by the rotors, also known as downwash, unnaturally alters concentration measurements. Downwash turbulence could create locations of varying pressure, which could affect concentration. A UAV fitted with gas sensors was attached to a stand in a controlled environment containing a mixture of NOx. The gas sensor measuring points were placed at various distances on and from the UAV body to evaluate downwash effects on gas concentration. Results show that the presence of downwash turbulence causes no statistically significant changes to concentration measurements at any distance or direction from the UAV. Based on these results, it is possible to use a UAV-mounted gas monitor to measure concentrations without concern for downwash interference, provided the UAV and measuring point are entirely contained within the gas cloud.

May 20, 2021

By Paul D. Tomlingson

There are huge benefits for mining operations that have a well-defined maintenance program that is understood and followed across the total operation. But for operations lacking a quality maintenance program, there is equal assurance that nearly every major maintenance problem can be traced to this omission. Few problems will be permanently corrected until such a program is implemented. Definition The maintenance program re-quires the interaction of all mine departments. Initially, the production department will request work and the maintenance department will identify work, principally through preventive maintenance inspection and testing efforts. Maintenance will then classify the new work to determine the best way to respond. Maintenance will plan selected major jobs to enable its crews to carry them out more effectively. Maintenance will schedule the planned work with operations. Supervisors will assign all types of work to their crews then, control the work through effective supervision. As work is completed, maintenance will measure the work using an accurate information system. Next, it will assess overall accomplishments against goals such as performance standards or budgets. In addition, the pro-gram would prescribe a means to evaluate every aspect of the operation as it affects maintenance so that necessary improvements or changes can be identified, prioritized and acted on. Such evaluations should be part of a mine-wide continuous improvement effort. A well-defined maintenance program is one of the best investments a mining operation can make to assure its profitability. Educating the total operation on the pro-gram assures long-term dividends from the investment.

Jan 1, 2008

By Fernanda Santos da Luz

Desde o período Neolítico, a argila é usada na produção de materiais para construção. Posteriormente, verificou-se que queima da argila em fornos aumentava a resistência do material, permitindo seu uso na maioria das formas abrasivas. Com a melhoria das propriedades, a cerâmica vermelha encontrou várias aplicações tais como, telhas, tijolos, louças e revestimentos. Na região estudada, a noroeste do Rio de Janeiro e a área leste da zona da mata mineira, as telhas produzidas e comercializadas exibem características correspondentes à argila local e ao método de queima. Neste trabalho foi avaliada a qualidade das telhas na região, referente às características geométricas, físicas e mecânicas, padronizadas pela norma NBR 15310:2009. De acordo com a análise dos resultados, concluiu-se que a tendência da qualidade das telhas existentes no mercado não atende aos parâmetros atuais da norma brasileira. O teste geométrico apresentou o maior número de não conformidades. A planicidade da superfície e os testes de rendimento também apresentaram desvios maiores em relação ao padrão aceitável. As não conformidades encontradas nas amostras indicaram que ocorreram falhas nos controles de fabricação do produto e na aprovação do lote que liberou o material para a produção de fábrica, resultando em produtos sem padronização.

Oct 30, 2017

By Tiago Evangelista Gomes

O presente trabalho teve por objetivo verificar a influência do Nióbio na trabalhabilidade a quente de um aço inoxidável duplex do tipo UNS S32304 em condições similares às do processamento industrial, utilizando ensaios de torção a quente. Foram fundidas, em forno de indução a vácuo, 4 corridas experimentais: uma com a composição química padrão e as outras objetivando-se teores de Nióbio de 0,2%, 0,4% e 0,8%. Ensaios de torção a quente foram realizados em resfriamento contínuo a partir de 1.200ºC, e ensaios isotérmicos no intervalo de temperaturas de 1.200 a 900ºC. O aumento da fração volumétrica de ferrita em função do aumento da concentração de Nióbio melhorou a trabalhabilidade a quente destas ligas.

Jul 30, 2018

By Leandro Brunholi Ramos

O aço API 5 CT P110 é amplamente utilizado no setor de petróleo e gás no Brasil devido sua elevada resistência mecânica, contudo ele não possui uma boa resistência a corrosão. Com a descoberta do pré-sal, novos desafios surgem neste setor, tornando necessário o desenvolvimento de novas tecnologias resistentes aos ambientes agressivos que os materiais serão expostos. A aspersão térmica por HVOF se destaca pela obtenção de revestimentos contra corrosão e resistentes ao desgaste com baixa porosidade e com um relativo baixo custo em comparação a outros processos. Dentre os materiais que podem ser aplicados como revestimentos por aspersão térmica, o níquel se destaca pela ótima resistência à corrosão por formar um óxido protetor na superfície. Sendo assim, o presente trabalho tem por objetivo obter e caracterizar revestimentos de níquel obtidos por aspersão térmica HVOF, no aço API 5CT P110. Os revestimentos foram caracterizados morfologicamente por microscopia eletrônica de varredura (MEV). Foram obtidas curvas de polarização para avaliar o comportamento frente à corrosão e foram realizados ensaios para determinação do coeficiente de atrito. A camada aspergida de níquel apresentou resultados satisfatórios quanto às análises estudadas.

Aug 8, 2018

By John P. Capp

In recent years limited markets have been developed for fly ash, the dust removed from coal-burning powerplant stacks, but most of it is still dumped in spoils areas at a cost ranging from 20 cents to $1.75 per ton. Aside from this cost, the creation of huge spoils areas can present a considerable aesthetic problem. Since the present annual fly ash output of about 20 million tons will probably reach 30 million by 1970, and because satisfactory disposal areas are becoming more limited, markets for much larger quantities of the waste are needed to keep disposal costs from becoming a significant economic factor in coal-burning powerplant operation. Current stress on air-pollution control and beautification, plus the vital need for good powerplant economy, makes it imperative, therefore, that coal producers and consumers expand markets and develop new applications for fly ash. Markets for established uses can be increased by making a greater effort to sell fly ash. New large tonnage markets for fly ash should be sought via more intensive, coordinated research. The economics of fly ash utilization underscores the vital role that must be played by research. To be competitive with other products, processes for the conversion of fly ash into marketable materials face difficulty in regard to two important economic factors--transportation cost and product utility--the other economic factors are favorable. Raw material costs of fly ash, for example, are quite attractive, and supply is no problem because there are many coal-burning powerplants in operation and many more are planned. Demand for products made from fly ash will grow if their utility is established and a good sales program is initiated. The major problems then are transporta¬tion costs and development of useful products.

Jan 1, 1966

By Géssica Seara Faria

A corrida pela alta produtividade, a demanda pela otimização de processos, que proporciona maior economia de combustível, impulsiona o desenvolvimento de estruturas veiculares de menor peso. O aço Bake Hardening (BH) é um aço de ultra baixo carbono estabilizado ao titânio, que apresenta átomos de carbono em solução sólida ocupando posições intersticiais. Este passa por um tratamento realizado durante o trabalho de pintura do veículo, permitindo que as chapas sejam endurecidas pelo efeito BH, conferindo resistência à endentação. Neste estudo um aço BH foi analisado em quatro condições de processo: laminação a quente, laminação a frio, recozimento e encruamento, com o objetivo de estudar os efeitos da variação destes parâmetros nas propriedades mecânicas do material, através dos ensaios de tração, obtendo resultados como valor de alongamento adquirido e dureza.

Aug 16, 2017

By Richard D. Smith

The Bureau of Mines evaluated the emission control methods, including the capital investments and operating cost, necessary for further reducing lead levels in ambient air at the Glover, Herculaneum, and Buick smelter-refineries in Missouri and the East Helena, MT, smelter. The U.S. Environmental Protection Agency (EPA) has proposed more stringent lead in ambient air standards than those currently in effect. This report presents theoretically achievable lead emission reductions and estimated capital and operating costs. Lead emission inventories theoretically can be reduced from 1985 levels by 2,421 lb/d at the three Missouri operations by containing and filtering fugitive emissions within structural enclosures and baghouses. The aggregated capital and operating costs in 1986 dollars using conventional environmental and workplace technologies are estimated to be $250,014,100 and $18,507,800, respectively. Estimated total incremental cost is $0.063/lb as refined lead. Additional regulatory costs attributable to Occupational Safety and Health Administration (OSKA), U.S. Department of Labor, workplace standards are included since proposed environmental controls may otherwise degrade workplace conditions. Continuous drossing is evaluated as an alternative to conventional OSHA controls. Substituting continuous drossing for conventional work- place technology results in an estimated aggregated capital and operating costs of $258,344,800 and $15,719,600, respectively. Estimated total incremental cost is $0.062/1b as refined lead. For comparison, the average open market price of refined lead during the first quarter of 1986 was $0.184/lb.

Jan 1, 1987

By Larissa Fernandes Nunes, Luiz Paulo Mendonça Brandão, Mônica Aline Magalhães Gurgel, Eustáquio de Souza Baêta Júnior, Andersan dos Santos Paula

Aços assistido pelo efeito TRIP (Transformation Induced Plasticity) com alto teor de Al estão sendo desenvolvidos com grande potencial de se tornarem aços de terceira geração para aplicações no setor automotivo. Assim, por ainda estarem na fase de desenvolvimento, estudos sobre esses materiais são de extrema relevância. Este trabalho buscou correlacionar a influência da laminação a frio e recozimento intercrítico, em uma liga de aço TRIP com elevado teor de Al, com o comportamento da liga face as análises de transformações de fase via Calorimetria Diferencial de Varredura (DSC), identificação de fases e textura da matriz ferrítica via Difração de Raios X (DRX) e aspecto microestrutural via Microscopia Óptica (MO). O processamento termomecânico adotado, com distintas temperaturas de encharque no recozimento intercrítico, não influenciaram a textura cristalográfica da liga, entretanto, distintos percentuais de austenita retida foram verificados para cada condição, sendo o maior valor observado para a temperatura de 820 ºC.

Oct 27, 2019

By Breno Totti Maia

O presente trabalho teve por objetivo uma análise de parâmetros geométricos de bicos de lança em operação e uma extrapolação para situações futuras. Foram determinadas as principais relações trigonométricas e, a partir disso, verificada a possibilidade de “coalescência”. Os principais resultados mostram que círculo primitivo dos bocais (PCD) não tem qualquer influência nas relações trigonométricas do bocal, limitado pelo ângulo de saída divergente. Bicos com até 04 furos e pequeno ângulo com a vertical podem promover a coalescência e bicos com mais furos afastam essa possibilidade assim como a relação entre número de furos e ângulo entre dois bocais adjacentes. O presente trabalho mostrou uma importante ferramenta para determinação de condições para desenvolvimento de novos bicos de lança.

Aug 17, 2017

Jan 1, 1985

Separation of Nickel and Cobalt from Manganese, Magnesium and Calcium by Synergistic Solvent Extraction - From Batch Tests to Pilot Plant Operation The synergistic solvent extraction system consisting of Versatic 10/LIX63/TBP was used for the separation and purification of nickel and cobalt from synthetic laterite leach solution after iron removal. Very encouraging results were obtained for separating nickel and cobalt from manganese, magnesium and calcium. In batch tests, the organic composition of the synergistic system was optimised and very large synergistic shifts for nickel and cobalt were observed. The ?pH50(Mn-Co) and ?pH50(Mn-Ni) values were as large as 1.65 and 2.40, respectively. The extraction and stripping kinetics of nickel and cobalt was fast. Semi continuous extraction tests were conducted with a pH profile of 5.5/6.1/6.5 in three stages at 40¦C. The nickel and cobalt extractions reached 99.9 per cent with only 5 mg/L Ni and <1 mg/L Co left in the raffinate. With two stages of scrubbing, only 2 mg/L Mn and less than 1 mg/L Mg and Ca were left in the scrubbed organic solution. With two stripping stages, the stripping efficiencies of Ni and Co reached over 95 per cent. A fully continuous pilot plant operation was conducted successfully for 280 hours. With an O/A ratio of about 2 and a pH profile of 5.5/5.8/6.0/6.3 for the four stages EX1/EX2/Ex3/EX4, both nickel and cobalt were almost completely extracted. Using a pH profile of 5.4/5.0 for SC1/SC2, the manganese scrubbing efficiency was over 96 per cent. Using three strip stages, over 98 per cent Ni and 99 per cent Co were stripped with only 64 mg/L Ni in the stripped organic solution. The nickel concentration in the loaded strip liquor reached 83 g/L, resulting in a ?Ni of over 28 g/L. The chemical stability of the system was also assessed over 12 weeks under proposed industrial operating conditions. Operation exclusively under strip conditions at 50¦C and 40¦C resulted in LIX63 oxime half lives of 1.1 and 2.1 years, respectively. Operation exclusively under extract conditions at 50¦C and 40¦C resulted in oxime half lives of 0.26 and 0.82 years, respectively. Losses of Versatic 10 were less than four per cent.

Sep 13, 2010

State ownership of minerals results in domestic legislation regulating mining operations. The mining industry today is dominated by a number of transnational companies, each subject to internal and external pressures for a more responsible approach to resource management. Thirty to 40 major companies are responsible for the bulk of the worldÆs mineral production with the balance coming from state-owned, second tier and junior companies and from artisanal miners.Mining companies operating within competitive commercial environments formerly focussed on mineral production. Companies worked to standards and expectations then current which largely failed to recognise the impact of mining activities on community interests. The mining industry acquired a reputation for arrogance, and for placing profitability ahead of issues considered equally or more important by local communities. Current perceptions continue to reflect disquiet about industry attitudes towards traditional land-owners and access to their lands, to environmental contamination, handling and storage of waste materials, utilisation of water and electricity, and to rehabilitation of worked out areas. Major international mining companies concerned at continuing criticism sponsored a series of initiatives with the objective of providing guidance on working harmoniously within the community. Industry commissioned studies, performed through the agency of disinterested parties, resulted in May 2002, in a Declaration being issued at an International Conference in Toronto. The Declaration was based on, but did not reflect all of the recommendations of the MMSD Report, æBreaking New GroundÆ.This paper considers whether benefits would result from the negotiation of a legally binding and enforceable international protocol encompassing the objectives of the MMSD report or the Toronto Declaration. It attempts to identify the problems associated with implementing and enforcing international mining law, should it be introduced. Aspects of mining operations having cover under customary international law are reviewed, as are rights, obligations and remedies for breaches of national mining law. Conclusions are drawn based on established procedures relating to implementing international agreements. The continuing ability of mining companies to operate within communities will result from each satisfying the communityÆs expectations rather than by complying with largely unenforceable legislation.

Jan 1, 2004

By C. Hilton

Arch Coal Inc. has implemented and sustained Best Practices at its four western mines through utilizing foremen in ongoing time studies. A prime benefit is the unique opportunity provided to front line supervisors. To date, 48 supervisors have participated in this program. Each quarter a new team is assembled with members from each operation. During three month blocks the supervisors conduct studies at each mine and identify best practices to implement at their own mine. Ongoing Best Practice and Action Item lists are reviewed each study. Mine management edits, prioritizes and monitors the completion of the proposed action items.

Jan 1, 2010