Search Documents

Curiously enough, considering the relative accessibility of the two places, coal was reported at an earlier date in Saskatchewan than in British Columbia. Henry and Thompson were on the Saskatchewan River in February 1811, and on the 4th of that month recorded, while on Jack's Branch of North Brook, "I observed in one of the bends on the north side a bank of yellow clay, on which there appeared several horizontal veins of pure coal, of the best quality I have seen along this river." Later at Rocky Mountain House it was said: "a quantity of coal is tumbling into the water, as the current washes away the earth underneath. This coal abounds along the Saskatchewan, in some places forming solid beds several feet thick for several acres, which are washed by the river. In its pure state our smiths use it for the forge with equal proportions of charcoal made of birch or aspen, which answers every purpose for making and repairing our axles and other tools."1 It is needless to say that it was many years before this coal was used for any commercial purposes. Coal was first found on the northern end of Vancouver Island in British Columbia in 1835 at Beaver Harbor, where later Fort Rupert was established, where Indians had advised some of the Hudson Bay Company officials it would be found.2 The coal was used by smiths, and later on by the steamer plying along the coast.3 A report to the government in 1845 called attention to the coal reported in the neighborhood of Puget Sound and on the Cowlitz River, and that probably the samples used by the Hudson's Bay Company were obtained from the surface and. were not good. On September 7, 1846 a report on the coal situation was submitted by Ogden and Douglas, and a naval vessel was sent to investigate the report and was loaded with 62 tons dug out by the Indians, the seam outcropping along the shore.2 In 1847 some samples were sent to England by a returning war vessel. In 1849 the Hudson's Bay Company established a

Jan 1, 1942

By J. W. R. Rayner

THE conventional method of making water gas involves individual plants for the separate carbonization of coal to coke and the subsequent gasification of coke with steam. The process demands lump coke, preferably made from the best quality of coking coals. The ash in the coke should have a high melting point and the gasification process suffers a loss of efficiency when cokes with law ash-melting points are used. In Britain, these coals are generally the most expensive and they are readily available only in certain localities. The coals not suitable for making lump coke, or yielding only poor quality coke, are much more widely available and are generally cheaper. DEVELOPMENT OF ALTERNATIVE PROCESSES In Germany, processes have been developed and operated commercially for the production of water gas from very low-rank coals such as brown coal and lignites, but much less effort has been spent on processes to use coals of intermediate rank, which are widely available in Britain. The brown-coal processes use coal in the form of either dust or briquettes. The most successful of the dust-gasification methods is the Winkler process, which made a substantial contribution to German oil production during the war. It uses coal in the site range 0 to 8 mm and the fuel bed is blown with a mixture of oxygen and steam at a rate high enough to give it a characteristic boiling motion or, in present-day phraseology, at a rate more than sufficient to fluidize it (Fig. 1). Air cannot be used to provide the heat required for gasification, for various reasons. In the first place, to make the process continuous by mixing air and steam would involve the production of a lean gas-containing much nitrogen. If a separate blow were used, a large amount of potential heat would be lost because the blow gas in such a process would contain a very high percentage of carbon monoxide. Oxygen is necessary therefore and oxygen remains relatively expensive for use in gasification. In the Winkler generator, formation of clinker caused by local overheating does not occur, because of the mobility and high heat transfer of a fluidized bed. These properties of fluidized dusts have been used most successfully

Jan 1, 1953

By E. E. Carpenter

Believing that the results accomplished in the mill of the Churchill Milling Co., Wonder, Nev., during the fiscal year ended Sept. 30, 1914, will be of interest, I am presenting the more prominent facts and figures showing the progress made in treating this ore with especial reference to tonnage, supplies, costs, and extractions. The mill is situated at Wonder, Nev., in the Wonder mining district, 55 miles east from Fallon, Nev., the nearest railroad point. All supplies are hauled this distance by freight teams, this method of transportation having been found more reliable for continuous service than truclis, the price paid for hauling being slightly under one cent per pound. In this mill are treated the ores of the Nevada Wonder Mining Co. Ore is Unusually Hard The company which tested this ore before the mill was built reported "This ore is an unusually hard, tough, oxidized quartz, carrying a small percentage of high-grade sulphides, containing good values in both gold and silver. None of the rebellious silver minerals appear to occur in appreciable quantities." ... "In regard to the mill tonnage this ore is unusually hard and tough, and a high stamp duty cannot be expected. Using a 20-mesh screen and 1,050-lb. stamps, our best work was three tons per stamp per 24 hours." It is very probable that the ore delivered to the testing plant was harder than the regular mill run has proved to be. However, at present the mine is developed to a depth of 1,000 ft., and still shows hard ore in places at this depth in about the same proportion as on the upper levels from which the test ore came; during this year's work, ore was treated from nearly all levels. Together with this hard ore in the mill feed a considerable proportion appears to be broken down and tending to crumble, thus making an ideal mixture for stamp milling. A small proportion of talc is also noticeable, which sometimes increases in amount to the point where it is very troublesome in the thickeners.

Jan 1, 1916

INSTITUTE MEDALS AND PRIZES ASIDE from the John Fritz Medal, in which the Institute participates through its representation on the John Fritz Medal Board, the Institute itself has five major awards to make annually for excellence in technical papers, as follows The Robert W Hunt Medal, The Hadfield Prize, The J E Johnson Jr , Award, The Lewisohn Platinum Prize to senior members, and the President's Prize to junior members ROBERT W HUNT MEDAL The partners of Robert W Hunt established a fund which was presented to the Institute at a fitting ceremony on May 27, 1920, to establish an annual medal and a sum of money to be awarded under the following rules, 1 The award shall consist of two prizes, first of a gold medal, second of a sum of money, a certificate to accompany each prize The money prize shall not be awarded to a member over 40 years of age, but under unusual circumstances, both prizes may be allotted to one person provided that he is not over 40 years of age In general it will be understood that the Committee shall award the money prize to, the younger men, rather than the medal 2 The awards shall be made not oftener than once a year to that person or persons contributing to the Institute the best original paper or papers on iron and steel The scope of the term "iron and steel" shall be determined by the sub-committee consider¬ing the awards In general, papers dealing with the practical side of the subject have preference over those dealing with the theoretical side in recognition of the fact that Captain Hunt's main contributions to the industry have been in the improve¬ment of production and quality of material 3 A sub-committee of three to five, including the Chairman of the Iron and Steel Committee, shall be appointed by the Iron and Steel Committee annually to adjudge the award subject to approval 4 The awarding committee shall submit its report to the Iron and Steel Committee at its October Meeting, and the award be certified to the Secretary of the Institute in time to permit the presentation to be made at the Annual Meeting of the Institute 5 The recipient of the award shall be designated "The Hunt Medallist "

Jan 1, 1923

Discussion of the paper of E. L. deGolyer, to be presented at the Colorado meeting, September, 1918, and printed in Bulletin No. 137, May, 1918, pp. 987 to1000. J. A. UDDEN,* Austin, Tex. (written discussiont).-I have read Mr. E. L. deGolyer's paper on The Theory of Volcanic Origin of Salt. Domes, with a great deal of interest. It seems to me a very able summary and discussion of the various theories set forth to account for the origin of our salt domes on the coast. It has always appeared to me that what we need is more observations on the facts involved and I regret very much that so far we have not been able to devote much time to the study of our salt-dome fields on the coast in this State. One feature that I do not find mentioned in Mr. deGolyer's paper is the so-called "cap. rock" overlying the salt. The nature of this rock seems to vary from a coarsely crystalline limestone to a fine-grained limestone containing sand and in which the limestone seems to be intersticially introduced material. We should be prepared to accept, if necessary, "more than one theory. To my mind, the igneous theory and the artesian theory, if I may so call it, may very well both be true. The "squeeze" theory and the artesian .theory may,, it seems tome also, jointly explain the phenomena. Neither the volcanic nor the salt "squeeze" theory explains the presence of the cap rock. The latter certainly does not explain the extensive sulphur deposits which occur in association with the cap rock. Whichever additional theory will be found best to explain the salt-dome structures, when we shall know them better, it seems to me that the theory first advanced by R. T. Hill and later elaborated by G. D. Harris, is not likely to be entirely replaced. Whatever cause has first set into action an upward circulation of gases and liquids in our salt domes, it seems to me that to a gentle circulation of the kind postulated by their theory is to be ascribed the uppermost and the later phenomena in our salt domes on the coast, with which we are most familiar; such as the cap rock, the sulphur, and the gypsum and anhydrite deposits.

Jan 7, 1918

By Lynne Bowen

"On the da y shift in Number One Mine at Nanaimo on Vancouver Island, on May 3, 1887, William Griffiths, a coal miner with many years experience, fired a shot to advance the face of the crosscut. A flame ran out for a distance of fifteen feet along the roof and then extended up the slope for ten to twelve feet, and although many would have called this a blowing out shot, Griffiths said it was just a feeder. ""A blower"", he said, ""would have caused an explosion."" 1There was no explosion. Griffiths reported gas and the area was cleared for three hours and then work resumed. When the shift changed at 3:00 p.m., the fireman reported all places clear of gas and the ventilation good.2The ventilation in Number One Mine was the best anyone had ever seen. The air in the mine was almost too cold. The current was so strong that it sometimes blew out the flame on the miners' fish oil lamps. It delivered five to six hundred cubic feet of air for every man and animal working in the mine. The law required only one hundred cubic feet 3The miners considered Number One to be relatively safe. The manager was proud of the mine and its up-to-date equipment"". Recently, there had been reports from France and America about the explosiveness of coal dust, but the manager did not think his mine was sufficiently dusty to be dangerous.5 The dust lay thick on the floor of the mine. Sometimes when a shot was fired the dust rose in great clouds. When a miner was shovelling it, the dust would billow up and be carried off by the current of air. The dust was also in the roof and in the stopings, put there intentionally to fill up the spaces and prevent the accumulation of methane gas."

Jan 1, 1992

ENERGY 73 The First International Energy Exhibition will be held in Brussels from 13th to 18th May, 1973. Vllth INTERNATIONAL CONGRESS ON CYBERNETICS This congress will be held in Namur, Belgium, from 10th to 15th September, 1973. GRADUATE SCHOOL OF BUSINESS ADMINISTRATION University of the Witwatersrand The Sixth Executive Development Programme is scheduled to take place from 2nd July to 24th August, 1973. IFAC SYMPOSIUM 1973 Second announcement ofthe International Symposium on AUTOMATIC CONTROL IN MINING MINERALS AND METAL PROCESSING to be held at the University of New South Wales, Sydney, Australia, from 13th to 17th August, 1973. MINERALS AND ENVIRONMENT The effect ofthe mineral industry on the environment and mineral resources The Institution of Mining and Metallurgy, with the co-operation of the Institute of Quarrying and the Institution of Mining Engineers, will hold a Symposium "Minerals and the environment" at the Institution of Electrical Engineers, Savoy Place, from 4th to 7th June, 1974. COLLOQUIUM ON SLlMES DAMS The South African Institute of Mining and Metallurgy have great pleasure in advising members that a two-day colloquium on slimes dams is bei ng arranged for the 14th and 15th November, 1973. INTERNATIONAL SOLVENT EXTRACTION CONFERENCE This conference will be held at Lyon from 8th to 14th September, 1974. Particulars may be obtained from the Secretary: Dr A. Naylor, British Nuclear Fuels Ltd., Windscale and Carder Works, Seascale, Cumberland CA20 IPG, United Kingdom. Competition for Student Members of the South African Institute of Mining and Metallurgy Each year the Institute offers a prize (or prizes should the entries warrant it) of up to RIOO for the best paper or dissertation on a topic appropriate to the interests of the Institute. Proceedings of the Tenth International Symposium on Application of Computer Methods in the Mineral Industry (APCOM) The Proceedings of the APCOM Symposium held in Johannesburg from April 9th to 14th, 1972, have now been published. Members of the Institute may buy the Proceedings at a special price of R12,50 as against the list price of R25,00 to non-members. Verrigtinge van die Tenth International Symposium on Application of Computer Methods in the Mineral Industry (APCOM) Die Verrigtinge van die APCOM Simposium, wat op April 9 tot 14, 1972, in Johannesburg gehou is, is gepubliseer. Lede van die Instituut kan die Verrigtinge teen 'n spesiale prys van R12,50 koop, in teenstelling met die prys van R25,00 vir nie-Iede.

By Robert H. Richards

This truly remarkable machine was built on a preliminary scale in May, 1895. The first full-sized table was built by Mr. A. R. Wilfley, and was used in his own mill in Kokomo Colo., in May, 1896. The first table sold for installation was placed in the Puzzle mill, Breckinridge, Summit county, Colo., in August, 1896. The mill enthusiasts at first hailed it as the cure for all the ills that flesh is heir to in the milling line. A little later it was found to make losses which were serious, and on this account the table succeeded only to a limited extent in displacing the vanners of the gold-mills. Still later, mill-men in a number of districts throughout the country made special studies of the faults of the machine, and devised a number of ways of grouping supplementary machines to overcome as far as possible the losses, and at the same time retain the benefit of the extraordinarily large capacity accompanied by the production of clean concentrates for which the machine has become so justly famous. I hope to make an exhibit of some of these methods in an appendix to my book on ore-dressing which is now in preparation. These experimenters have not written up the subject, and if they possess all the facts they have not given them out for the benefit of the mining profession at large. The object of this paper is to obtain the facts and to present them so clearly that their bearing can be seen by all. To this end two complete series of tests have been planned. One (the present paper), to study concentration of galena in presence of quartz; the other (to follow shortly), to study concentration of chalcopyrite in presence of quartz. Some authorities claim that the table does its best work when treating natural products; by this phrase I mean products which have been crushed to pass through a limiting

Jan 1, 1908

By B. Silliman

The experiments detailed by Dr. Hunt,* having demonstrated the fact that the copper contained in the "clay ore" of Jones's Mine, was rendered completely soluble in the bath of ferrous chloride, used in the Hunt and Douglas process, after heating in contact with carbonaceous matter in a close vessel, I set myself to devise a form of muffle furnace adapted to the treatment of large quantities of these and similar ores by a continuous process. The result is shown in the diagrams on Plate X, reduced from the working drawings, after which this furnace was built early in 1876, at Phœnixville, by the Chemical Copper Company on their works at this place. The peculiar character of this ore determined the form, dimensions, and position, with reference to charging and discharging of these muffles. The ore arrived from the mine with from 20 to 25 per cent. of moisture, and when dried at 21o F., or more slowly at lower temperature, it falls to a light incoherent powder, with occasional lumps of undecomposed rock. In this condition it is readily mingled with coal-dust or any like reducing agent, and requires no other preparation for the muffle than the use of the shovel, to mix it well with the reducing agent. As it is a remarkably good non-conductor of heat, it was obvious that the mass, to be heated through in a reasonable time, must not be too thick, while the weight of the mass must be sustained in a way to avoid undue strain upon the walls of the muffle. These walls must be as thin as practicable, to favor the more rapid transmission of heat, and must, therefore, be so constructed as to admit of being stayed on the sides at frequent intervals to resist the lateral thrust of the very mobile mass of pulverulent ore, which, for obvious reasons, must be charged at the top and drawn from the bottom of each chamber. These considerations led to the form adopted, viz., two vertical muffles, standing upon very strong bridge tiles, seen in longitudinal section, on the line E, F, and in plan in Fig. 3, on the same plane. (Plate X.) The vertical section of the muffle is seen in Fig. 4, drawn in the plane G, H, of the longitudinal section, Fig. 6, which is the key to all sections. The walls of the muffles are built of the best firebrick, very care-

By Frank B. Fulkerson

A study was made of scrap iron and steel in the South Central States in order to determine trends in processing, shipment, and consumption of this important commodity. These data were derived in part from statistical sources and in part by visits to scrap yards and steel mills. Trends in the industry were reviewed. Dealers in 1963 supplied 1.8 million tons of iron and steel scrap to steel mills and foundries in the south-central area, compared with 2.1 million tons in 1955. Most of the scrap was processed and shipped within 200 to 300 miles of consuming centers. Exports provide a principal outlet for dealers along the gulf coast. Most of the scrap that fills these orders is loaded onto freight cars at yards in Texas and Louisiana and -is shipped to ports for direct transfer from railroad car to ship. The tonnage exported varies greatly from year to year. The largest scrap operations are in or near large cities which are heavy scrap generating areas, steel mill sites, or port cities for export of scrap. A tentative analysis indicates that the short-run supply of prepared scrap is inelastic to price changes; therefore, buyers probably arc in a strong bargaining position at times of declining demand. One technological development in the iron and steel scrap industry is the use of large presses which can take complete automobiles with frames, wheels, springs, and other heavy parts still intact and reduce them to bundles. At Houston, Tex., and Kansas City, Mo., shredding plants are in operation that reduce car bodies and other light scrap into flat pieces 4 to 6 inches in size.

Jan 1, 1966

By O. C. Baptist

The Umiat oil field is in Naval Petroleum Reserve No. 4 between the Brooks Range and Arctic Ocean in far-northern Alaska. The Umiat anticline has been tested by 11 wells, six of which produced oil ; however, [lie productive capacity and recoverable reserves of the field are subject to considerable speculation because of unusual reservoir conditions and because several wells appear to have been .seriously damaged during drilling and completion. Oil is produced at depths of 275 to 1,100 ft; the depth to the bottom of the permanently frozen zone varies from about 800 to 1,100 ft, .so that most of the oil reserves are in the permafrost Reservoir pressures are estimated to range from 50 to 350 psi, increasing with depth, and the small amount of gas dissolved in the oil is the major source of energy for production. Laboratory tests were made on cores under simulated permafrost conditions to estimate oil recoverable by solution-gas expansion from low saturation pressures. The cores were also tested for clay content and susceptibility to productivity impaiment by swelling clays and increased water. content if exposed to fresh water. The results indicate that oil can be produced fronz reservoir rocks in the permafrost and that substantial amounts of oil can be produced from depletion-drive reservoirs by a pre.s.r~lrr drop of as little as 100 psi below the saturation pressure. Freezing of formation water reduces oil productivity much more than that due to increased oil viscosity: Failure of we1ls drilled with rtuter-base mud to produce is attributed to freezing of water in the urea immediately surrounding the wellbore. Swelling clays apparently contributed very little to the plugging of the wells. INTRODUCTION Naval Petroleum Reserve No. 4 lies between the Brooks Range and the Arctic Ocean in northern Alaska. The Umiat oil field is located in the southeastern part of the Reserve and is about 180 miles southeast of Point Barrow (the only permanent settlement in the Reserve and the primary supply point for drilling of the wells at Umiat). Eleven wells were drilled for the U. S. Department of the Navy, Office of Naval Petroleum and Oil Shale Reserves, between 1944 and 1953 to test the oil and gas possibilities of the Umiat anticline. Six of these wells produced oil in varying quantities and the best one pumped about 400 B/D.' Estimates of recoverable oil range from 30 to 100 million bbl. The main oil-producing zones are two marine sandstone beds in the Grandstand formation of Cretaceous age: these are referred to as the upper and lower sands. Good oil shows were found throughout the sand settions in the first three wells drilled on the structure, but the highest rate of oil production obtained on any 01 the many tests was about 24 BOPD. These first wells were drilled with conventional rotary methods using water-base mud; later wells were drilled either with cablc tools using brine or rotary tools using oil or oil-base mud. These experiments were successful as is shown by comparing the oil production from Well No. 2 with that from No. 5. These two wells are only 200 ft apart and are located at about the same elevation on the structure. Well No. 2. drilled with a rotary rig using water-base mud, was abandoned as a dry hole after all formation tests were negative. Well No. 5. drilled with cable tools and reamed with a rotary using oil, pumped 400 BOPD which was the maximum capacity of the pump and less than the capacity of the well. These field results indicated that the producing sands were extremely "water sensitive" and it was assumed that the cause of this sensitivity was the presence of swelling clays in the sands. Because of the very unusual reservoir conditions and the difficulties encountered in completing oil wells in the permafrost. the Navy asked the U. S. Bureau of Mines to make laboratory studies under simulated permafrost conditions to assist them in estimating the production potential of the field and the recoverable reserves. These tests were designed to determine the cause of the plugging of wells in the permafrost and to test oil recovery from frozen sand by solution-gas expansion with the oil gas-saturated at very low pressures. EXPERIMENTAL METHODS AND PROCEDURES Samples Analyzed Core samples were analyzed that represent the lower sand in Umiat Well No. 7, the upper sand in No. 3. and both the upper and lower sands in No. 9. These sands should be productive in all of the wells because of their location on the structure. Core samples from

By Linn Bradley

F. H. WILLCOX, Pittsburgh, Pa. (communication to the Secretary*). -We must keep in mind, in balancing the savings-to be anticipated by the most efficient combustion of gas, the best heat absorption by stoves or boilers, and by heat conservation of the thermal equivalent carried in. blast-furnace gas-against the cost in operation, maintenance, depreciation and interest charges of the equipment required to realize the savings, that in boilers and hot-blast stoves we are basing our economies upon two different, combustion phenomena. In a boiler, evaporating water at a heat efficiency of 70 per cent., approximately 47,550 B.t.u. is consumed per boiler horsepower. Taking the blast, furnace gas cited in the above paper, we are using about 38 ¾ lb. of cold-washed gas per boiler horsepower. Using the hot-cleaned gas, the same equivalent heat is furnished by 34 1b. of the gas , This leaves of the 38 ¾ lb. required in the case of cold-washed gas, 4 ¾ lb. or 6,650 B.t.u. available for raising more steam when dry-hot gas is used, which means that an equivalent amount of coal firing can be dispensed with. Per ton of iron, this figure 2/3 X 12,000/38.75 X 4.75 = 980 lb. gas or 1,372,000 B.t.u. or 100 lb. coal. At $1.50 per ton of coal, the net saving per ton of pig iron produced by the use of dry-hot over wet-cold cleaning will, therefore, be about $0.06 2/3. At a stove heating 8,500 lb. of air per toil iron from 150° F., one-quarter of the dry-hot cleaned gas, or 3,000 lb., would heat the air to 1,450° F. 3,000 X 1,400 X 0.70 = (8,500 X 0.255) = 1,300. The cold-wet gas would heat the same amount of air to 1,280° F. 3,000 X 1,225 X 0.70 = (8,500 X.0.255) = 1,130.

Jan 4, 1917

By G. S. Scott, H. G. Turner, W. L. Kleene

It is well known that different forms of carbon show differences in chemical behavior under apparently identical conditions. It is fairly well known that these differences persist, although to a lesser degree, in a single group of carbons, such as the anthracites of Pennsylvania. It is the purpose of this paper to show the extent of these variations for Pennsylvania anthracites from actual quantitative measurements of the amount of carbon dioxide reduced under the standardized test conditions employed. As the amount of carbon dioxide reduced to the monoxide (under comparative conditions termed, for convenience, the "reactivity") is important in combustion, gas production and metallurgy, it is hoped that this paper will be a useful contribution to the store of knowledge on these subjects. In carrying out the investigation, considerable time and thought were spent in obtaining what seemed to be the best possible design of apparatus. The next step consisted in making a number of trial runs on the same sample, varying temperature, particle diameter, etc. and then outlining a standardized procedure to be followed in testing all samples. Fifty anthracites were tested. As a matter of interest, some 10 miscellaneous samples were also tested. The data show initial reaction temperatures (abbreviated I.R.T.), reaction velocity constants at 900" and 950" C., some effects of added substances, and a few additional tests designed to throw some light on the causes of differences in reactivity. The sample of charcoal, as was anticipated, proved to be easily the most reactive of any sample tested. The anthracites as a group came second. The five samples of gas and by-product cokes, obtained from five different coke manufacturers, came third, and a single sample of Rhode Island anthracite ranked fourth, with respect to reactivity as above defined. Although the five coke samples do not necessarily represent the average market coke, and five samples constitute a rather small number of samples to serve as a basis for comparisons, the fact that none

Jan 1, 1934

By L. C. Armstrong

A. E. ROSS*—Mr. Armstrong in his paper stated that they had experienced considerable difficulty in drilling the quartz-feldspar intergrowths. The dia-mor~d loss was excessive and the diamond bits polished quite rapidly. Mr. Davidson, who presented the paper, stated that bortx stones in the range of 20 to 30 per carat had been used in the bits on this job. I would like to suggest the use of bits employing stones in the range of 60 to 100 per carat, an average of possibly 80 per carat. If these stones had been used the bits might have lasted longer and not polished so quickly. As a basis for this suggestion I would like to point out that in northern New York State we had at least two examples where bits employing stones in the range of 80 per carat had solved a difficult problem. Bits set with stones in the range of 20 to 30 per carat had been used previously and had failed. With the finer stones, the cost per foot of drilling decreased material1y. It should also be noted from a technical standpoint that the smaller stones require higher drilling speeds than the larger stones. Greater pressures are not normally necessary, and it is the higher speed which seems to be the major factor of importance. It should also be noted that the finer stones afford a greater number or cutting surfaces for the same carat weight in a bit. Then too, the smaller stones, by virtue of their size, serve as sharper cutting edges than larger stones. There is no doubt that the diamond bit employing smaller stones costs more to set than the bit using larger stones. However, with the technique developed at the shops of Sprague and Henwood, Inc., we feel that the relatively slight additional cost required to set these bits is more than paid for by the resultant lower drilling cost. We feel that the highest quality stone available is the most economical to use when hard fine grained rock is encountered. In summary, I would suggest that it might be possible to solve the problem presented in this paper by using a diamond bit employing stones at least as small as 80 per carat of the highest grade possible and by using the diamond bit at the highest speed available with modern drilling equipment. L. C. ARMSTRONG (author's reply) —It is generally agreed that the use of smaller, high-grade diamonds and of higher drilling speeds, as suggested by Mr. Ross, may be the best approach to the solution of the problem.

Jan 1, 1950

By Robin O. Williams

The increase in internal energy as the result of deformation has been measured for lead, aluminum, silver, nickel, iron, and zirconium by using rapid, adiabatic compression. The stored energy increase is roughly Proportional to the strain; the propor-tionality constant increases rapidly with increasing melting point. The fraction of the mechanical energy which is stored increases more slowly, since the strength of the metals also increases with melting point. The values of the stored energy are considered accurate to about 10 pet. The present values appear about 50 pet larger than the more reliable published results where comparisons are possible. It is possible that this difference is due to the high strain rate used in this investigation. Immediately after deformation all these metals release energy at a rate roughly proportional to (time)-'. This release is considered to be associated with dislocation motion but in aluminum (and copper) some additional process seems to be present. This release can represent 20 pet or more of the stored energy. WHEN pure metals are plastically deformed, most of the mechanical energy is converted into heat. The energy remaining within the metal is significant in that it is the energy of the disorder produced and thus detailed knowledge of this energy is a powerful tool in understanding the nature of deformational disorder. While much effort has been expended on this problem, the amount of information available is limited. The situation as of 1958 has been carefully reviewed by Titchener and ever.' The present results have been obtained by a new experimental approach to this problem. The method necessitates high-strain rates which make comparisons with published results less certain, but a high-strain rate is an advantage in that the energy release immediately after deformation can be followed. EXPERIMENTAL PROCEDURE In the experimental method used, the internal (stored) energy is given as the difference between the mechanical work used in deforming the sample and the heat which is released (the first law of thermodynamics). The work is supplied by two identical hammers swinging freely from a fixed height, the available energy being the product of the mass, the gravitational constant, and the distance through which the center of gravity moves. The initial temperature rise of the sample represents the heat produced by the deformation. The sample temperature is determined by a small thermocouple embedded in and supporting the sample. This process can be repeated over and over to produce increased strains. Most samples are run through about five cycles to a total strain of around 0.7. Further details are covered elsewhere. The determination of the heat is dependent upon the sample weight, its specific heat, the rise in temperature, and any gains or losses to the surroundings. One is dependent on published results for specific heals (the values were taken from a collection).3 The values must be accurate to about 0.1 pet in order that they not affect the results. The best values thus do not contribute to the uncertainty, but this is probably not always the case. The accuracy of the temperature rise is limited primarily by knowledge of the thermocouple characteristics over short temperature intervals, but careful calibration eliminates this as an important factor. One can calculate readily the heat flow between the sample and hammers if the time of contact and the sample temperature are known and if there were no oil at the interface. Assuming the maximum temperature difference, upper values for this interchange have been calculated (the time of contact is determined from the decrease in sample length) and it may or may not be significant. However, no correction is colnsidered necessary because of the presence of a thin oil film which has a thermal conductivity much less than the metals. Except for the possible uncertainty in specific heat, the heat is considered to be adequately known. The mechitnical losses which are recognized as important are: 1) friction between the sample and the hammer:;, 2) the kinetic energy in the hammer suspension system which may not be entirely usable, 3) the rebound energy of the hammers, and 4) the vibration of the hammer heads. All these have been covered in detail elsewhere2 and only the more significant points are made here. The friction turns out to be small except for soft materials (lead)

Jan 1, 1962

While coal was undoubtedly seen by the Spanish explorers in Texas, no mention can be found of it in any of their available published records; it was likely noticed by the first Americans, and coal along the Rio Grande River was reported in 1834.1 The next record is that of brown coal in Bastrop County in 1837 by James Nicholson and Judge Pinckney Hill? Dr. Riddell saw brown coal along the Trinity River in 1839 and described it as follows: "In the banks of the Trinity, associated with the iron ore, and overlying the brown coal, whole trees and fragments of trees, piled sometimes one upon another, present themselves completely transformed into stone. In some logs a diversified metamorphosis is observable; one portion of the vegetable structure having been replaced with silex, another with brown oxide of iron, and a third is bitumenized or converted into coal. "In concern with Dr. F. B. Page, I took considerable pains in the exploration of the Trinity brown coal formation., As no excavations for working have yet been made, the best places for inspecting the formation are where the Trinity cuts its way through the highlands, or where its banks present themselves in bold high bluffs, as at New Cincinnati, and near the site of the projected town of Osceola. The coal lies in horizontal strata, dipping one foot in thirty to the northwest. The main stratum at the latter place, just above Bedias creek; is represented by the concurrent statement of W. C. Brookfield, surveyor, Mr. James S. Hunter, of Huntsville, Texas, Dr. Page, and some other persons whom I consulted, as between six and seven feet in thickness, the lower portion being between three and four feet above low water mark. Unfortunately, during my sojourn there, the river was unusually high and turbid for the season of year; I could not consequently verify the same by personal observation and measurements. The most considerable coal beds which I had opportunity fully to inspect, were in the Trinity bluffs, southwest side, at New Cincinnati, six miles lower down, and just below the mouth of Salt creek, near six miles above. The workable stratum of brown coal in each of these localities is about five feet thick, and situated some fifteen feet or so above low water mark. In quality it is said to be precisely similar to the coal in the seven feet bed."2 . Moore in 1840 mentioned coal in the vicinity of Great Salt Lake, through which the Brazos flows; lignite in Bastrop County; lignite in the banks of the Colorado River a few miles above Lagrange in Fayette County; a deposit of excellent coal in the bed of the Sabine River, 30 miles above the

Jan 1, 1942

By Wayne E. Glenn

A centennial meeting should be a time to take stock, to evaluate performance, to plan ahead. It is like a line in a televised commercial that goes, "You've come a long way to get where you've got to today." And no less should be said of the mining and energy industries. We have come a long way. A hundred years ago when AIME was founded, this country produced 23 million tons of bituminous coal and 5.2 million bbl of oil. The figures in 1970 were about 580 million tons of coal and 4.1 billion bbl of oil. In spite of such accomplishments, serious and compelling voices are heard in the land - doubting sincerity, questioning corporate structures, and challenging ethics. Those doubts are raised in one part of Washington at the same time that other sections of the Capitol are asking us to produce more energy in order to keep up with population growth, emerging nations, and new technologies. Those of us in the fuel or energy business frequently talk about the race for energy. The question is, can we develop enough energy fast enough to outdistance our present and increasing demands? Recently I heard of an incident that - in an odd way - caused me to think of the energy race. The incident involved a sky-diver who jumped from an airplane without a parachute. He was handed a chute in mid-air by a sky-diving companion. He put it on, opened it, and landed safely. In a way, it seems to me that our society is hurtling through space and that it needs some help from the energy industries to land safely. We're doing our best, but under some rather difficult conditions. Because of illegal strikes and work stoppages the coal parachute is snarled a bit. The cut in percentage depletion and other tax changes have put some holes in the oil parachute. And the gas ´'chute has been in trouble for some time because of unrealistic controls on producer prices. The irony of the situation is that some of the very people who have been taking potshots at the energy parachutes for a long time are the ones who are complaining loudest now because the 'chutes are not functioning the way they could. The safety of the entire nation can depend on the energy industries.

Jan 1, 1971

By B. F. Buie

Included in the general category of clays is a large and varied assemblage of nonmetallic silicate minerals which characteristically occur as fine-grained particles having flaky, sheetlike, or rod-shaped form. Most, though not all, are hydrous aluminum silicates. Amount and kind of impurities vary greatly, and these strongly influence the uses of the various clay types. Clays occur in a wide range of geological situations: as bedded sedimentary deposits composed of the weathering products of feldspar and other minerals; as alteration products of igneous, sedimentary, and metamorphic rocks weathered or hydrothermally altered in place; and, to a more limited extent, as hydrothermally introduced materials. TYPES AND MARKETS On the basis of chemical composition and crystal structure, two major groups of clay minerals recognized are the "kandites" or kaolin group, and the "smectites" or montmorillonite group. Another major type is illite, particularly important as a constituent of shales. Two additional mineral species having economic importance are attapulgite (palygorskite) and sepiolite. For present purposes, however, a classification based on utilization is more appropriate. The U.S. Bureau of Mines recognizes six types of clay: kaolin, ball clay, fire clay, bentonite, fuller's earth, and miscellaneous clay. Kaolin The kaolin group of minerals consists of the mineral species kaolinite, halloysite (metahalloysite), dickite, and nacrite, although the latter two are not being produced commercially. Kaolin, also called china clay, is a high-purity white material. Perhaps it is best known as a principal ingredient in the manufacture of chinaware, porcelain, and other high-quality ceramic products. However, by the mid-1970s very close to 50% of the kaolin produced in the United States was going to the paper industry for use as a filler and coating material. Manufacture of refractories uses about 12% of U.S. production. Kaolin is also used in plastics, in the rubber industry as a filler in footwear, electrical cable, and similar products, and as a conditioner of rubber for automobile tires to add strength and abrasion resistance. Smaller amounts are used in printing ink, paint, and adhesives; as insecticide carriers; in the production of catalysts for the petroleum refining industry; and in many other industrial and commercial applications. Production and use of kaolin in the United States doubled in the ten years from 1946 to 1956, and doubled again by 1966. Growth continues at a rate of about 7 % per annum.

Jan 1, 1976

The Ranger Project Area covers 78.6sq km and is approximately six km east-west by 14km north-south (Fig. 1). The area is known to con- tain two uranium orebodies, Ranger No. 1 and No. 3, two uranium occurrences, Anomalies 4 and 5 and three significant radon anomalies, Ranger 18, 19 and 48. The Ranger No. 1 and No. 3 Orebodies con- tain approximately 120 000 tonnes of U308 in highly chloritised metasediments of the Lower Proterozoic Cahill Formation. The orebodies occur as suboutcrop and exhibit significant radiometric anomalies. These occur within approximately 400m vertically of the projected unconformity with the sandstone of the Middle Proterozoic Kombolgie Formation. Oxidised and reduced uranium minerals occur in quartz-rich schists containing variable muscovite, chlorite and sericite and in the chloritic matrix of chert breccia. Secondary uranium minerals namely saleeite, metatorbernite and gummite associated with earthy iron oxides occur from the surface to 50m depth in No. 1 Orebody and up to 80m depth in No. 3 Orebody. Below the oxidised zone, uranium occurs as pitchblende finely disseminated throughout sequences of quartz muscovite chlorite schist up to 150m thick and as open space fillings in zones of structural deformation. The uranium-bearing schists directly overlie up to 300m of dolomite and magnesite containing minor interbedded schist units and are themselves overlain by approximately 2 000m of more micaceous schists of the upper part of the Cahill Formation. Regional metamorphism has occurred to at least amphibolite facies and has been followed by retrograde metamorphism to a greenschist facies equivalent. The metasediments are intruded by granitic pegmatites and dolerites. Uranium is associated strongly with chlorite of which there are at least five textural varieties. Not all of the various generations of chlorite have associated uranium. Graphitic schist horizons occur which are often less than one metre thick and discontinuous. These are best developed at the base of the quartz chlorite schist sequence where uranium grades up to 1 000ppm U may extend for several hundred metres beyond the main ore zone. Uran- ium is not common in the carbonate sequences and only occurs in chlorite segregations in disrupted zones. The unoxidised ore contains sulphides, mostly pyrite, which are low in abundance (

Jan 1, 1984

By Stanley C. Herold

A few hates on the occurrence and significance of mud volcanoes in Colombia may be of interest at the present time, owing to the renewed activity in geological exploration of the coastal regions bordering the Caribbean Sea. The best-known volcanoes are found a few miles from the seacoast. One is situated to the south of Puerto Colombia; the second, to the east of Cartagena near the village of Turbaco; and the third, near the village of Puerto Escondido south of the Sinu River. Others are reported in more inaccessible localities. Usually they stand 2 1/2 or 3 ft. (0.762 or 0.914 m.) above the surrounding ground at the crater, though several craters from 10 to 20 ft. -(3.04 to 6.09 m.) "apart will often build up an extensive mound at low gradient. The shallow mound may cover 1/2 or 3/4 acre (0.2 to 0.3 ha.) with an elevation of 12 or 15 ft. (3.65 or 4.57 m.) at the, center. The craters are formed of hardened blue clay; the inside diameters vary from 14 to 24 in. (35.56 to 60.96 cm.). The rim is continuous, except on one side where there is usually a cut 3 or 4 in. deep, thus allowing an overflow. The craters are filled to the' rim-cut with a thick mixture of blue clay mud and water, which is kept in agitation by escaping gas. Fig. 1 shows the bubble in the act of bursting and Fig. 2 the appearance of the surface of the viscous fluid a second or so later. The frequency of the explosions is determined by the weight of the column of fluid in the neck of the volcano, consequently, such explosions are not synchronous in a group of craters. Ordinarily, there arc two or three explosions in about 3 minutes. The supply of gas is small but steady and sufficient pressure must accumulate before the bubble can enter the column of fluid. The water is derived from the surface and enters the scdirnentary strata not far distant from the volcano. During long dry seasons, as the supply of water fails the volcano dries and geyser action ceases. The temperature of the muddy fluid is normal; the gas is dry and inflammable. - No petroleum products come with the gas. On the surface of the fluid, there is sometimes a dark brown streaky scum, which

Jan 1, 1920