Search Documents

By C. L. Magee, H. W. Paxton

PREVIOUS workersl'% ave found that as-quenched ferrous martensites can be plastically deformed at low stresses. They have also found that the stress to obtain small strains can be significantly increased by aging at temperatures up to 150°C. This behavior has been interpreted in two ways: 1) that the deformation at low applied stress is due to internal stresses and thus the aging phenomenon is due to relaxation of the internal stresses;' 2) that the microdeformation arises through the motion of unpinned dislocations and the aging process is the diffusion of carbon to the dislocations to pin them.293 In a recent paper,4 we have shown that under certain conditions the dominant microdeformation mechanism of as-quenched Fe-31Ni marten-site-austenite aggregates is the transformation of retained austenite. Our results on resistance changes during deformation and temperature dependence of the deformation also established that, at temperatures above 300° K, the microdeformation was not due to this transformation. The purpose of this note is to report results of experiments which indicate that explanation 1 is appropriate for this deformation. All results presented here are from conditions where transformation does not make a measurable contribution to the microplastic deformation, in Fe-31Ni-0.002C, or in Fe-29Ni-0.02C-0.25Ti. The experimental techniques that were used for measurement of the plastic deformation are described4 and analyzed5 elsewhere. Fig. 1 shows the microplastic response of 100 pct austenite at 300" and 350° K. The microplastic response of an austenite-martensite aggregate is also given in Fig. 1 and it is seen that, after formation of martensite, the initial plastic deformation occurs at lower stresses. Thus, the softness is not entirely due to retained austenite—the quenched structure can be deformed at lower stresses despite the fact that the macroscopic strength is significantly higher. A result which allows a distinction to be drawn between the alternative explanations for this behavior is derived from aging experiments on the low-carbon alloy containing titanium. We have previously shown4 that the presence of titanium in this alloy reduced the free carbon to a sufficiently low level that thermal stabilization of the austenite-martensite transformation was not detected. Despite this, Fig. 2 shows that the microplastic response is decreased by aging treatments. A similar aging effect in Fe-ZONi, with some titanium, has previously been reported by . Thus, carbon is not necessary for the aging process and explanation 2 is at best incomplete. Since internal stress relief can occur independently of carbon (any temperature dependence of the flow stress can result in decreased internal

Jan 1, 1969

By L. R. Weisberg, E. A. Miller

Single-crystalline films of silicon of good quality were vacuum-deposited on sapphire. The improved crystallinity was achieved by the strict exclusion of oxygen from the evaporation system, including the use of a "oxygen-free" silicon source. To minimize possible contamination of the source, the silicon was sublimed from the solid at about 1390° C. using a simple electron bombardment system to heat the silicon. This resulted in deposition rates of about 5 to 7 µ per hr and film thicknesses of 4 to 20 µ. The vacuum during deposition was ordinarily about 5x 10-8 Torr, DESPITE the success achieved in the chemical vapor deposition of silicon on sapphire using Silane,1-4 vacuum deposition has not provided comparable properties. For example, Chu et a1.5 vacuum-deposited silicon on single-crystalline substrates of A12O3, Sic, ThO2, and other compounds, and, although some epi- but the use of ultrahigh vacuum (about 1 to 3 x10-9 Torr) during deposition did not significantly improve the results in the oxygen-free system. The crystalline quality of films deposited on (0001) sapphire was found to be considerably superior to (1102) sapphire surfaces. Using (0001) sapphire, single-crystalline films were deposited at temperatures as low as 780° C and as high as 1075°C, with the best crystalline quality obtained at about 1000°C. At this temperature, hole mobilities over 250 sq cm per v-sec were achieved. taxy was indicated, single-crystalline films were not produced. More recently, Salama, Tucker, and young6 evaporated silicon on single-crystalline sapphire, but only poor crystallinity was observed, and low carrier mobilities were measured. In the present experiments, good-quality single-crystalline films of silicon on sapphire have been achieved by specifically excluding oxygen from the evaporation. This included not only the use of a "clean" vacuum system but, of special importance, the use of an oxygen-free silicon source. This has also been shown to provide a dramatic improvement in silicon homoepi-taxy.7 As a result, silicon-on-sapphire films with hole mobilities over 250 sq cm per v-set were achieved, and single-crystal films were grown as low as 780°C and as

Jan 1, 1969

By Edward Schuster

As THE time allotted is short, we can present only a general idea of the oil laws in the Latin-American republics, as a supplement to Bulletin 206 of the Department of the Interior compiled under the direction of J. W, Thompson of the Bureau of Mines and entitled "Petroleum Laws of All America." We shall not discuss the European colonies in Latin-America nor the island republics. As to the countries discussed, we shall attempt to give the main features of such special petroleum legislation as has been adopted prior to the early part of this year; where no special petroleum" laws exist, we must look to the mining codes for light on the petroleum policy. As the laws and regulations for the extraction of the metals are often difficult of application to, and are lacking in many essentials for, the petroleum industry, it is best for persons or companies desiring to enter, on . a large scale, into the petroleum exploration and development of countries not having special petroleum legislation, to obtain a concession contract from the executive of the country under consideration, and to have the concession approved by the congress. If this concession, which would then be a special law, contains nothing contrary to the constitution of that country and does not infringe on vested rights of third parties, it should be reasonably safe. If in such country there is some doubt as to whether the petroleum subsoil is owned by the nation or the private surface owner, only public lands should be covered with the concession. Guatemala is the only republic in the group that discriminates directly against foreigners. Bolivia, Ecuador, Mexico and Venezuela require waivers of diplomatic protection.1 Colombia requires foreigners to agree to be bound by its alien law. , In addition,Mexico makes it unlawful for foreigners to acquire direct ownership of real estate, including mines, within a zone of 50 km. along the coasts and one of 100 km. along its land

Jan 7, 1922

By J. B. Clemmer, F. D. DeVaney, H. A. Doerner

PRODUCTION of magnesium metal in the United States during the past decade has increased from less than 6oo,ooo lb. in 1928 to more than 4,800,000 lb. in 1938.1 The growing industry has stimulated interest in methods of production and in sources of raw material. All of the present domestic production is from brines. However, the availability of large tonnages of magnesite in the state of Washington, together with the possibility of cheap power, have created interest in the utilization of magnesite for the production of magnesium metal as well as for other purposes. Magnesite, the carbonate of magnesium (MgCO3), usually is associated with limestone (CaCO3) and dolomite (MgCO3CaCO3). It occurs in crystalline and microcrystalline (sometimes termed amorphous) forms.2 The more common crystalline mineral is found in various shades of white, gray, yellow and brown, the colors being due to impurities, chiefly iron. Magnesite has a hardness of 3.5 to 4.5 and a specific gravity of 3.0 to 3.1. It forms rhombohedral crystals in the hexagonal system, having a vitreous, pearly luster. The quarries and mines of the Northwest Magnesite Co. near Chewelah, Wash., are large producers of magnesite for refractories. The deposits are extensive, some veins being hundreds of feet wide. The boundaries of the veins are indefinite, and the magnesite is interfingered with dolomite. Calcite, talc, serpentine, quartz and shale are disseminated through the deposits. The quality of the ore cannot be determined by appearance or by simple tests; chemical analysis is required. These features make it difficult to determine the boundaries or total quantity of workable ore.3 Only the higher-grade ores are mined, and a considerable proportion of the magnesite content is discarded by hand-sorting and log-washing methods. After calcining, the sorted product meets the specifications for usual refractory material, as it contains approximately 81 per cent MgO, 7 per cent Si02, 6 per cent CaO and 6 per cent Fe203 + A1203. A sample of the reject material had the following analysis after calcining: 65.4 per cent MgO, 6.3 CaO, 21.1 Si02 and 6.5 R203. The percentage reported as R203 includes compounds whose chlorides are acid-soluble but give precipitates in ammoniacal solution that are ignited and weighed. The more common constituents are Fe203, A1203 and Ti02. The sorted magnesite product is not the best grade, even for refractory purposes, and leaves much to be desired for a reduction process. The rejected material contains a large proportion of magnesite. It is apparent that an effective concentration method would yield a higher recovery and a better product. In general, the refractory grade is not suitably pure for other uses. Recent developments in the production of

Jan 1, 1940

By R. F. Dickerson, D. A. Vaughan, A. F. Gerds

ALTHOUGH the metallurgy of uranium has been under intensive study since the early 1940's, no systematic effort has been made to identify the non-metallic inclusions in uranium. Uranium carbide (UC), which is probably the most common inclusion found in graphite-melted metal, has been tentatively identified by previous investigators, but the other nonmetallic inclusions have received little attention. Since metallography is a valuable tool in metallurgical studies, the metallographic identification of the nonmetallic inclusions in uranium is important. Such an investigation has been completed and the identification of slag-type inclusions and of uranium monocarbide, uranium hydride, uranium dioxide, uranium monoxide, and uranium mononitride is described. Metallographic Preporation It is often possible to prepare specimens for metal-lographic examination equally well by several methods. The specimens which were examined in this work were prepared by one of two acceptable methods. For the convenience of the reader, both methods will be discussed in detail and will be referred to simply as Method I or Method II in the subsequent sections. For both Methods I and 11, specimens for microscopic examination usually were mounted either in bakelite or in Paraplex room temperature mounting plastic. Method I—Specimens were ground in a spray of water on a revolving disk covered successively with 120-, 240-, and 600-grit silicon carbide papers. It was necessary to perform the final grinding operation carefully on worn 600-grit paper to keep the scratches as fine as possible. After washing and drying, the specimens were polished for 3 to 4 min on a slow speed wheel (250 rpm) covered with a medium nap cloth. Diamet Hyprez Blue diamond polishing paste, Grade 00, 0 to 2 µ, was used as abrasive with kerosene as lubricant on the wheel. Specimens were washed thoroughly in alcohol and final polished electrolytically in an electrolyte composed of 1 part stock solution (118 g CrO, dissolved in 100 cm3 H2O) with 4 parts of glacial acetic acid. A stainless steel cathode was used. At an open circuit potential of 40 v dc, a polishing time of 2 sec retained inclusions well with the bath at room temperature. If additional etching was required to sharpen the interface between the metal and the inclusions, an electrolyte composed of 1 part stock solution (100 g CrO3 and 100 cm8 H20) and 18 parts glacial acetic acid was used at room temperature. Best results were obtained by etching for from 10 to 15 sec at 20 v dc in the open circuit. Surfaces obtained by this method are suitable for microscopic examination. However, if desired, they may be etched further with other chemicals. Method 11—Rough grinding was done on a wet 180- or 240-grit continuous grinding belt. The specimen was then ground by hand successively on 240-, 400-, and 600-grit silicon carbide papers in a stream of water. Final polishing was accomplished on a 4 in. high speed wheel (3400 rpm) covered with Forstmann's cloth. Linde B levigated alumina, suspended in a 1 volume pet chromic acid solution, was the abrasive. Specimens usually were polished in 5 min or less by this technique. Often the inclusions present in the metal were identified in the mechanically polished condition. When etching was required to outline inclusions more sharply, one of the two following methods was used. In the first method, the specimen is etched lightly while electropolishing in the chromic-acetic acid solution described above (1 part of stock solution to 4 parts of acetic acid). The electrolyte was refrigerated in a dry ice-ethyl alcohol bath and specimens were etched at 60 v dc on the open circuit for 2 or 3 cycles of 3 to 4 sec each. The second technique utilizes electrolytical etching at about 10 v dc (open circuit) in a 10 pet citric acid solution at room temperature. X-Ray Diffraction Technique The major problem in the identification of inclusions in metals by X-ray diffraction techniques is the extraction of a sufficient amount of each type of inclusion to obtain an X-ray diffraction pattern. In the present study, X-ray diffraction patterns were obtained from individual inclusions of the order of 10 µ diam. The polished and etched samples shown in the micrographs were examined at a magnification of X54 or XI00 with a binocular microscope. This allowed sufficient working distance to extract the inclusions with a needle probe for powder X-ray diffraction analysis. Friable inclusions such as MgF2, CaF2, UO2, and UH3 could be freed from the metal by probing the as-polished and etched surface. The fine particles then were picked up on the end of a Vistanex-coated glass rod (0.002 in. diam) which was held in a brass adapter made to fit the powder X-ray diffraction camera. The end of the glass rod was centered in the path of the X-ray beam. In the case of the UC, UO, and UN inclusions which are smaller in size, more metallic in appearance, and less friable than the other inclusions, it was necessary to etch the inclusion in relief before extraction. UN inclusions etched sufficiently in relief in the electrolytic polishing solution described in Methods I and II by increasing the polishing time. UN inclusions were relief etched by extending the

Jan 1, 1957

By R. Bruce Thorndycraft

This paper will describe several modifications to design of con­ventional oxide gold heap leaching. They are targeted at reduc­ing costs and simplifying heap operations. These modifications were conceptualized during consulting work on over 90 differ­ent heap leaches. In 1995, a unique opportunity arose to imme­diately apply all of these design concepts to the permitting and construction of a new facility at the American Girl Mine in southeastern California. American Girl Mine has operated since 1987. In April 1995, the mine faced a situation with grave consequences for cash flow. Approval for mining of a new ore zone, Oro Cruz, had just been granted, after lengthy delays by California regula­tors. All existing pad space would be filled by October. Only 6 months were available, and new pad siting and design were still undecided. Permitting of a new pad had not begun. Options were quickly reviewed. A strong criteria for pad site selection and design was ease of permitting. There was also a strong desire to install a system that would achieve better met­allurgical recovery and reduced operating costs, compared to previous heaps at this mine. One site offered the best chance for rapid permitting. It was the site of the original 1987-90 heap leach. This already dis­turbed ground contained 1.6 million tons of heaped ore. The old heap had just completed detoxification and was about to be signed off as a Group C waste, ready for reclamation. Instead of recontouring and revegetating the old heap, which the reclamation plan anticipated, we offered BLM and the County something even better. We proposed to off-load much of the detoxed old heap, and reuse the space. The off-loaded material would be back-filled into the original open pit, imme­diately adjacent. While the footprint of the proposed new pad was much larger, the reuse of disturbed ground, and backfilling of the open pit, had very strong appeal to the regulators. Our permitting strategy included the technical design of the proposed new facility. Many of the new design details also appealed to the regulators, particularly the "zero active ponds" concept.

Jan 1, 1996

By Louis A. Carapella, William E. Shaw

MAGNESIUM and its alloys have long been characterized as possessing limited capacity for mechanical forming at atmospheric temperatures prior to rupturing despite their outstanding performances in this respect at elevated temperatures. Responsible for this behavior are the fundamental facts that these hexagonal-type metals have comparatively few slip elements at low temperatures for any extensive deformation and that, at high temperatures, additional slip elements become operative, thus enhancing greater plasticity under strain. The transitional point has been set at 225°C by Schmid1 for single crystals, and at 250°°C by Morell and Hanawalt2 for extruded magnesium metal. In a recent X-ray investigation on polycrystalline magnesium-alloy sheets, Barrett and Haller3 have revealed that, below the transitional temperature, the initial plastic deformation proceeds mostly by a twinning action; that, above such a temperature, the action is mostly by slip. The deep-drawing performance of the magnesium + 1.5 pct alloy sheett over a wide range of temperatures has been investigated by Weber and Vanden Berg,' and their results are presented in Fig r. It should be noted from this work that a maximum drawability of about 25 pct at room temperature has been obtained on this alloy under the conventional deep-drawing operations. For the same alloy, it is now possible to augment the cold drawability to about 40 pct by a process to be disclosed. Hitherto, this value has been obtained only by deep-drawing the alloy at around 230°C. That greater plastic flow is attainable at atmospheric temperatures on magnesium under certain deformational techniques was discovered by the authors6 in their analyses of plastic-deformational behaviors of pure magnesium. This fact is best illustrated in Fig 2 from the Hargreaves analysis6 performed by the authors under two different modes of loading. For direct test, a separate unstrained specimen was used for each load duration, whereas for the integrated test the same specimen was employed for all the five intermittent loadings so that the load duration was made additive throughout the investigation. The higher plastic flow-rate at room temperature, as designated by the Hargreaves constant S, was obtained by the integrated or intermittent loading procedure. The authors5 in further tests showed that, under such a procedure greater plastic flow was also realized with a progressive increase in deformational loads. These findings have been applied

Jan 1, 1947

By Harold B. Janzen, M. A. Nobles

Campbell and Martin1 described a new exploratory logging tool which was developed as the result of a new concept of the phenomenon that takes place when a porous formation containing mobile hydrocarbons and irreducible interstitial water is invaded by mud filtrate. They postulate that invasion will create a bank of interstitial water between the flushed zone and the undisturbed formation. This postulate was confirmed by Wyllie.' Thus, if R,, is greater than R, and mobile hydrocarbons are present, the resistivity profile with increasing radii from the borehole is high:low:high, as shown in Fig. 1. If mobile hydrocarbons are absent, the bank of interstitial water is indistinguishable from the undisturbed formation and the resistivity profile, when R is greater than R,, is high:low, as shown in Fig. 2. The zone containing the bank of interstitial water and residual oil was named the "low zone". Campbell and Martin conducted extensive electrolytic wedge and resistivity analog model studies to select a logging system that would reflect the presence or absence of the low zone. The system they selected was that of a family of lateral curves. The model studies indicated that the presence of a low zone could be detected in approximately 60 to 70 per cent of the producing sand reservoirs with a family of lateral curves provided that the sonde effectively occupies 90 per cent of the diameter of the hole. These studies were conducted with D, = 5d. The presence or absence of the low zone is best determined by a plot of the apparent resistivity vs spacing as shown in Figs. 3 and 4. A dip or inflection in the profile that repeats at successive depth intervals is considered diagnostic. To reduce the shunting effect of the hole and mud, a sonde of insulating material that is surrounded by a series of flexible rubber bumpers was designed. The bumper efficiency is considered to be the ratio of the bumper diameter to the hole diameter. Field tests conducted by Campbell and Martin on 10 wells with a tool that provided for station readings indicated that dips or inflections could be detected in 19 out of 25 known producing zones. INSTRUMENT DEVELOPMENT Halliburton developed a logging system to simultaneously and continuously record eight lateral curves. The instrumentation is described in the literature.' The original logs made

By Frank B. Fulkerson

A study was made of scrap iron and steel in the South Central States in order to determine trends in processing, shipment, and consumption if this important commodity. These data were derived in part from statistical sources and in part by visits to scrap yards and steel mills. Trends in the industry were reviewed. Dealers in 1963 supplied 1.8 million tons of iron and steel scrap to steel mills and foundries in the south-central area, compared with 2.1 mill ion tons in 1955. Most of the scrap was processed and shipped within 200 to 300 miles of consuming centers. Exports provide a principal outlet for dealers along the gulf coast. Most of the scrap that fills these orders is loaded onto freight cars at yards in Texas and Louisiana and is shipped to ports for direct transfer from railroad car to ship. The tonnage exported varies greatly from year to year. The largest scrap operations are in or near large cities which are heavy scrap generating areas, steel mill sites, or port cities for export of scrap. A tentative analysis indicates that the short-run supply of prepared scrap is inelastic to price changes; therefore, buyers probably are in a strong bargaining position at times of declining demand. One technological development in the iron and steel scrap industry is the use of large presses which can take complete automobiles with frames, wheels, springs, and other heavy parts still intact and reduce them to bundles. At Houston, Tex., and Kansas City, Mo., shredding plants are in operation that reduce car bodies and other light scrap into flat pieces 4 to 6 inches in size.

Jan 1, 1966

By D. S. Eppelsheimer, D. N. Williams

The compression texture of iodide titanium is determined and found to consist of a [0001] texture rotated 15° to 30° from the axis of compression. As the amount of reduction increases, the angle of rotation decreases. The 0001 rotation showed a slight preference for a <1010> rotation axis. RECENT investigation of the cold rolled texture of titanium&apos; has shown this metal to exhibit a new type of rolling texture. This texture can best be described as a (0001) [10i0] with the 0001 planes rotated approximately 30" to the transverse direction around a <10i0> rotation axis. Rather good results in explaining the cold rolled texture have been obtained by other workers&apos; by examination of the tension and compression textures. No information was found giving the tension texture of titanium. Generally the tension texture of a hexagonal close-packed metal is identical with its wire texture. The drawn texture of titanium has been investigatedh nd has been found to be predominately [10?0]. Since this is the common tension texture of hexagonal metals of low c/a ratio, the explanation of the difference between the rolling texture of titanium and the rolling texture of other hexagonal metals is not indicated by examination of the tension texture. Therefore, the compression texture of titanium should be particularly important in the explanation of the unusual transverse rotation of the 0001 planes found in the cold rolled texture. The compression texture of titanium was examined by Yen.",&apos; His results showed titanium to exhibit the usual [0001] texture up to 85 pct reduction. At higher reduction a double texture appeared in which the 0001 planes were rotated from 10" to 30" from the plane of compression. This change in the compression texture seemed unusual since the tendency for hexagonal close-packed metals is to approach the [0001] texture as the idea compression texture. Mechanical twinning generally occurs over a considerable range of reductions beginning at a rather low reduction. The samples used by Yen in his investigations were prepared by two methods. Compression in a testing machine was used up to a reduction of 85 pct. Compression by compression rolling was used at higher reductions. Since the change in texture occurred at the same reduction as the change in the method of compression, a connection between the two seemed likely. To check this possibility and to locate the position of the change in texture definitely, if it was found to exist, the compression texture of titanium was re-examined. An iodide titanium crystal bar (99.9 pct Ti) produced by the New Jersey Zinc Co. and donated by the Titanium Alloy Manufacturing Div. of the National Lead Co. was used in this investigation. Procedure The investigation of the compression texture was carried out in three steps; compression, specimen

Jan 1, 1953

By H. L. Talbot, A. J. Hall, R. S. Young

A METHOD for the chemical differentiation of oxidized cobalt from sulphide cobalt in complex mine and concentrator products is of considerable interest to a number of mining companies throughout the world. At Rhokana Corporation, in Northern Rhodesia, for instance, cobalt is found chiefly in the sulphide form, as carrollite, but a cobalt oxide mineral also occurs irregularly underground, and relatively small quantities in the mill feed from time to time are difficult to detect it visually at the concentrator. The oxide cobalt is not amenable to the sulphide flotation process used at Rhokana and nearly all of it passes into the tailing. The occasional. period when high tailing losses occur with no appreciable change in the cobalt content of the mill feed has naturally been disturbing to the concentrator staff, who had no means of determining whether an influx of cobalt oxide ore or laxity on the part of the mill flotation operators were responsible for these results. A procedure for determining oxidized copper minerals, based on their solubility in dilute sulphuric acid saturated with SO2, has been used for many years in the copper industry. In the presence of cuprite the procedure fails, but otherwise it gives results quite satisfactory for control purposes. Empirical methods for determining oxidized forms of zinc and lead have been proposed, but they are generally unsatisfactory except in isolated cases of a very simple ore. No published procedure for determining oxidized forms of cobalt or similar elements has come to the authors&apos; notice. EXPERIMENTAL PROCEDURE There are obviously two alternatives in attacking a problem of this nature. One is to employ a solvent for oxide cobalt that will not dissolve cobalt sulphide. The other is, to find a substance capable of oxidizing the cobalt sulphide to sulphate, which of course is water-soluble and can then be leached from the water-insoluble oxide cobalt. A representative sample of Rhokana cobalt oxide ore was secured, ground to minus 200-mesh, and carefully rolled to furnish a standard sample for this work. The analysis of this material gave the following percentages: Co, 0.55; Cu, 1.64; Fe, 2.98; S, 0.08; SiO2, 41.42; A1203, 11.20; CaO, 13.82; MgO, 3.80. As a source of cobalt sulphide a similar large sample of carrollite was prepared, analyzing Co, 23.36 per cent; Cu, 27.32; and S, 31.13. This sample of course was not pure carrollite, but was the best obtainable in quantities sufficient for a standard intended for considerable work. It was a pure sulphide sample, microscopic examination showing only carrollite, a little bornite, and gangue, with no visible sign of oxidized ore present. A wide variety of reagents were used in an effort to selectively dissolve oxide cobalt or to oxidize sulphide cobalt to

Jan 1, 1946

By William A. Johnson

The fundamental role of diffusion in many reactions occurring in solid metals has long been recognized, and there have been careful measurements of rates of diffusion in numerous alloy systems; but our understanding of the atomic mechanism by which diffusion occurs is scarcely in an advanced state.l-3 It is doubtful that this mechanism can ever be directly ascertained; rather, all imaginable mechanisms must be examined and the one that is in best accord with such data as can be obtained from suitably chosen experiments should be selected. Because of its relative simplicity, diffusion in a system containing only one kind of atomic species—commody called self-diffusion—is of considerable theoretical interest. It may be expected that diffusion theory will not be advanced appreciably until a wide variety of diffusion experiments—of which diffusion in a chemical concentration gradient and self-diffusion are two important types—are carefully performed and inter-compared. Aside from the purely theoretical interest in self-diffusion measurements, such studies will be of considerable engineering importance. The rate of any process in a pure metal requiring the movement of atoms, of which recrystallization and creep are two familiar examples, will be understood more readily with the aid of self-diffusion data.† Self-diffusion implies the diffusion of something into its exact counterpart; the detection of such a process is patently impossible, and it is necessary to substitute for it the diffusion of one isotope (in this case radioactive) into another isotope (in this case stable) of the same chemical element. There is, however, no reason to suppose that a radioactive atom will not diffuse at the same rate as its stable isotope, for all of the isotopes of the same element have exactly the same chemical properties; neither the difference in nuclear energy nor the difference in mass would be expected to exercise an important influence in this phenomenon. In this sense, self-diffusion may be thought of as the diffusion of radioactive atoms down a radioactivity concentration gradient, just as usual diffusion is the diffusion of one kind of atom down its chemical concentration gradient. The first measurements of self-difiusion were made by von Hevesy4-6 using the radioactive lead isotope thorium B in ordinary lead. The recent development of means for producing artificial radioactive elements has made possible similar measurements on gold,7, 8 copper,2, 9 and zinc.10, 11 Many of the data that have been obtained are rather poor, and no adequate reason has been given for their poorness; it appears, however, that the unsatisfactory results are characteristic of the particular experimental procedure employed, and not of self-diffusion measurements in themselves. The experimental technique that has yielded the poorer results is the deposition of a thin layer of radioactive atoms on the surface of a specimen and the determination of the rate of inward diffusion

Jan 1, 1941

By William A. Johnson

The fundamental role of diffusion in many reactions occurring in solid metals has long been recognized, and there have been careful measurements of rates of diffusion in numerous alloy systems; but our understanding of the atomic mechanism by which diffusion occurs is scarcely in an advanced state.l-3 It is doubtful that this mechanism can ever be directly ascertained; rather, all imaginable mechanisms must be examined and the one that is in best accord with such data as can be obtained from suitably chosen experiments should be selected. Because of its relative simplicity, diffusion in a system containing only one kind of atomic species—commody called self-diffusion—is of considerable theoretical interest. It may be expected that diffusion theory will not be advanced appreciably until a wide variety of diffusion experiments—of which diffusion in a chemical concentration gradient and self-diffusion are two important types—are carefully performed and inter-compared. Aside from the purely theoretical interest in self-diffusion measurements, such studies will be of considerable engineering importance. The rate of any process in a pure metal requiring the movement of atoms, of which recrystallization and creep are two familiar examples, will be understood more readily with the aid of self-diffusion data.† Self-diffusion implies the diffusion of something into its exact counterpart; the detection of such a process is patently impossible, and it is necessary to substitute for it the diffusion of one isotope (in this case radioactive) into another isotope (in this case stable) of the same chemical element. There is, however, no reason to suppose that a radioactive atom will not diffuse at the same rate as its stable isotope, for all of the isotopes of the same element have exactly the same chemical properties; neither the difference in nuclear energy nor the difference in mass would be expected to exercise an important influence in this phenomenon. In this sense, self-diffusion may be thought of as the diffusion of radioactive atoms down a radioactivity concentration gradient, just as usual diffusion is the diffusion of one kind of atom down its chemical concentration gradient. The first measurements of self-difiusion were made by von Hevesy4-6 using the radioactive lead isotope thorium B in ordinary lead. The recent development of means for producing artificial radioactive elements has made possible similar measurements on gold,7, 8 copper,2, 9 and zinc.10, 11 Many of the data that have been obtained are rather poor, and no adequate reason has been given for their poorness; it appears, however, that the unsatisfactory results are characteristic of the particular experimental procedure employed, and not of self-diffusion measurements in themselves. The experimental technique that has yielded the poorer results is the deposition of a thin layer of radioactive atoms on the surface of a specimen and the determination of the rate of inward diffusion

Jan 1, 1941

By James Terry Duce

In order to facilitate interpretation of the data in this chapter, we print the following excerpts from circulars to authors, compiled by Mr. Frank A. Herald when he was Vice-chairman for Production of the Petroleum Division, and revised in 1939. Generally in Table 1 the unit for prescntation of data is a field. For our purposes a field is defined as the whole of a surface area wherein productive locations are continuous. Such unit commonly includes and surrounds nonproductive areas. Such unit commonly includes a great variety of geologic conditions—several units of continuous productive reservoirs of distinctly different structure and of distinctly different stratigraphy. Therefore it is hoped that our authors will subdivide "field" so as to enable students to make analyses that may have scientific and /or commercial value. As to each spacc in the tabulation, it is citller (1) not applicable, (2) the proper entry is not determinable, (3) the proper entry is determinable, but not determinable from data available to the author, (4) the proper entry is determinable by the author. In spaces not applicable, the author will please draw horizontal lines; in spaces where the proper entries are not determinable, the author will please insert x; in spaces where the proper entries are detcrminable but not detcrminable from data available to the author, the author will please insert y; in spaces where the proper entries are determinable by the author he will, of course, make such entries. Generally, y implies a hope that in some future year a definite figure will be available. Inability to determine precisely the correct entry for a particular space should not lead the author to insert merely y. Contributions of great value may be made by the author in many cases where entries arc not subject to precise determination. In such rases the author should use his good judgment and make the best entry possible under the circumstances. For many spaces, the correct entries represent the opinion of the author (for example, "Area Proved") and in such cases the entries need not be hedged to such extent as in cases where the quantities are definite yet can be ascertained only approximately by the author. In cases under definite headings but where figures are only approximate, the author may use x. For example, if the total production of a field is known to be between 1,800,000 and 1,850,000, the author may report 1,8xx,xxx; or if the production is between 1,850,000 and 1,900,000, the author may report 1,9xx,xxx. Where a numeral is immediately to the left of x or y, such numeral represents the nearest known number in that position. As to quantity of gas produced from many fields the question will arise as to whether the figures should include merely the gas marketed or should include also estimates of gas used in operations and gas wasted. Although rough approximations

Jan 1, 1939

By William A. Johnson

THE fundamental role of diffusion in many reactions occurring in solid metals has long been recognized, and there have been careful measurements of rates of diffusion in numerous alloy systems, but our understanding of the atomic mechanism by which diffusion occurs is scarcely in an advanced state 1-3 It is doubtful that this mechanism can ever he directly ascertained, rather, all imaginable mechanisms must be examined and the one that is in best accord with such data as can be obtained from suitably chosen experiments should be selected Because of its relative simplicity, diffusion in a system containing only one kind of atomic species-commonly called self-diffusion-is of considerable theoretical interest It may be expected that diffusion theory will not be advanced appreciably until a wide variety of diffusion experiments-of which diffusion in a chemical concentration gradient and self-diffusion are two important types-are carefully performed and inter-compared Aside from the purely theoretical interest in self-diffusion measurements, such studies will be of considerable engineering importance The rate of any process in a pure metal requiring the movement of atoms, of which recrystallization and creep are two familiar examples, will be understood more readily with the aid of self-diffusion data † Self-diffusion implies the diffusion of something into its exact counterpart, the detection of such a process is patently impossible, and it is-necessary to substitute for it the diffusion of one isotope (in this case radioactive) into another isotope (in this case stable) of the same chemical element There is, however, no reason to suppose that a radioactive atom will not diffuse at the same rate as its stable isotope, for all of the isotopes of the same element have exactly the same chemical properties, neither the difference in nuclear energy nor the difference in mass would be expected to exercise an important influence in this phenomenon In this sense, self-diffusion may be thought of as the diffusion of radioactive atoms down a radioactivity concentration gradient, just as usual diffusion is the diffusion of one kind of atone down its chemical concentration gradient The first measurements of self-diffusion ii ere made by von Hevesy4-6 using the radioactive lead isotope thorium B in ordinary lead The recent development of means for producing artificial radioactive elements has made possible similar measurements on gold,7,8 copper,2,9 and zinc 10 11 Many of the data that have been obtained are rather poor, and no adequate reason has been given for their poorness, it appears, however, that the unsatisfactory results are characteristic of the particular experimental procedure employed, and not of self-diffusion measurements in themselves The experimental technique that has yielded the poorer results is the deposition of a thin layer of radioactive atoms on the surface of a specimen and the determination of the rate of inward diffusion

Jan 1, 1941

By W. C. Coffin

Fire-brick stoves have become a necessary part of the modern coke blast-furnace equipment, and are also superseding the cast-iron pipe stoves in anthracite- and charcoal-furnaces. The brick stoves in general use are of either the Cowper or Whitwell type, or modifications of these bearing the names of those who invented the alterations from the original types rather than any real departure from then]. All these stoves have approximately the same valve-equipment and follow the same line of operation. The waste gas from the furnace enters at one port and burns in a single combustion-chamber, and the heated products are drawn through the various passe; in the brickwork to a stack of proper height to create the necessary draught. The last passes of these stoves receive a very small percentage of the heat from the gas, owing to their extreme distance from the combustion-chamber; and this chamber also suffers great deterioration in the attempt to force the heat into the farthest passes. At best, about 70 per cent. of the heat taken up is held in the combustion-chamher and the first down-pass of the Whitwell stoves. Mr. Hugh Kennedy, Manager of the Isabella Furnaces, Pittsburgh, Pa., who has had a large experience with the fire-brick hotblast stoves, was so strongly impressed with the fact that but about thirty per cent of the brick of the average stove were doing proper duty as heat-agents, that, after careful study and experiment, he had three 20- by 60-feet stoves constructed with a view of more uniformly heating all the brick. In these the general lines of the Whitwell stove are followed, with the blast-connections unaltered, but gas is introduced at the bottom of each pass, and outlets are provided at the top, so that the gases have a direct natural draught in each pass and the highest heats are obtained at the bottom instead of the top. The natural tendency being toward the reverse condition, the brickwork soon acquires an almost uniform temperature.

Jan 1, 1893

By J. T. Berling, J. B. Conway

MANY studies have been devoted to the correlation of low-cycle fatigue behavior. Several of these have also been concerned with the identification of an effective approach to the prediction of low-cycle fatigue behavior from short-term tensile data. Perhaps the first such approach was that reported by coffin1 in the form: where is the plastic strain range, Nf is the number of cycles to failure, and c is a constant characteristic of a material. In this analysis by Coffin it was reasoned that in a short-term tensile test the value of Nf could be considered as equal to a , in which case the value of c is interpreted as the tensile ductility, f, measured in such a test. If, therefore, the Coffin equation is assumed to be applicable to a given material, it is a simple matter to predict the low-cycle fatigue behavior. Once the tensile ductility is known, this point is located at Nf = 1/4 on a log-log plot of vs Nf and a line is drawn through this point with a slope of to yield a prediction for the fatigue life. Actually, while this equation is quite useful it is not generally applicable, for experiment has shown that the value of —$ does not reflect the relationship between and Nf for all materials or even for a given material over all temperature ranges. An equation similar to the Coffin equation was prepared almost simultaneously by Manson.2 This expression had the form: In this case the exponent on Nf was not assigned any particular numerical value in accord with the various values of this exponent which had been observed for different materials and at different test conditions. Because of this characteristic it will be recognized that little use can be made of this expression in predicting low-cycle fatigue results. A fairly effective expression for use in predicting fatigue behavior was proposed by Manson3 based on a study of numerous sets of experimental results. This relation (Method of Universal Slopes) makes use of modulus of elasticity, ultimate strength, and tensile ductility, and assumes an exponent on Nf equal to 0.6 in representing the plastic strain range contribution to total strain range. While this equation of Man-Son does not yield completely accurate results it must be recognized as being the best means available at

Jan 1, 1970

By A. B. Kinzel

THE demands of the petroleum and chemical industries for steels to be used in pressure vessels and similar structures at artificially low tempera-tures are continually increasing, and the writing of proper specifications with suitable tests becomes increasingly important. Likewise, the selec-tion of suitable steels for such applications is of increasing concern to the metallurgist. It is generally recognized that highly alloyed steels of the austenitic stainless type retain their properties even at very low tempera-tures and represent the best technological solution of the low-temperature steel problem. However, in many instances less expensive carbon or low-alloy steels suitable for service within limited temperature ranges are available. The problem thus becomes one of defining the various factors involved in the production and fabrication of these less expensive steels and determining the temperature ranges in which their properties justify engineering application. Most of the applications involve welded structures, and the heat effect of welding as well as the nature of the weld metal are matters of prime concern. The first problem that the metallurgist faces is the determination of the type of test to be used as a criterion of the performance of the steel in low-temperature service. It has been generally recognized that the static properties of steel as determined in the ordinary tensile test undergo a gradual and relatively slight change as the temperature of test is lowered in the range of current interest; i.e., from room temperature to minus 120° C. It is further generally recognized that the behavior of steel under impact involving notch sensitivity is definitely affected at the lower temperatures. While the major subject of this paper is the effect of grain-refining deoxidizers, of low-alloy additions and of welding on the low-temperature notched-bar impact properties, an inquiry into the general behavior of steel under low-temperature impact testing is included. This is a pertinent portion of the investigation and the results thereof are

Jan 1, 1937

By D. G. F. Hedley, D. F. Coates, K. Barron

INTRODUCTION Preceding papers presented in this symposium have considered the influence of various parameters, such as geologic structure, groundwater, etc., on the stability of rock slopes and have given some analyses and guide lines for slope design. To carry out such analyses it is necessary to put numbers to these parameters; where possible, this is best done on the basis of in- situ observation and measurement. Since none of the design analyses can be considered exact and since conditions vary during excavation, it is also desirable to monitor the behaviour of the slopes as the excavation proceeds. In this manner a feedback of information on the actual excavation conditions can allow a continuous reassessment of the design parameters to be made and can give early warning of incipient failures. The purpose of instrumenting rock slopes is thus to provide information which fits into one of two categories: (a) To give basic data to assist on-site assessment and design of the rock excavation. (b) To provide data for the control and assessment of safety during excavation. The purpose of this paper is to review briefly some of the instruments and measuring techniques available for gathering this data and to indicate where such data may prove useful. This is not a comprehensive review of all available instrumentation but, rather, is a survey of some of the instruments and techniques with which the authors have had some experience and which have proven useful. STRUCTURAL ASSESSMENT Whilst most structural assessment of a site is done on the basis of geologic mapping and core examination, there exists some instrumentation which can, in particular circumstances, assist in this assessment. Seismic instruments can be used to determine the geometry of formations and to give an indication of the relative competency of rocks. These instruments operate using seismic reflection or refraction techniques and, although mainly confined to shallow sub-surface exploration, can be useful in distinguishing between soil/ bedrock contacts and, in some cases, the extent of weathered surface rock.

Jan 1, 1971

By A. J. Mortlock

Cobalt and nickel have been diffused at tracer concentrations in gold at several temperatures in the range from approximately 700° to 950°C. The diffusion penetration profiles were determined by a serial sectioning technique in which the gold is first anodized and then the anodic layer is dissolved in acid. In this ulay sections as thin as 250A could be removed reproduci-bly. In all cases, the region close to the specimen surface was characterized by irregular behavior in the sense that the logarithm of concentration was not linear in the square of the penetration distance. In sotne cases, there zuas an indication of the operation of very slow dijfusion in this region, while in others the apparent diffusion coejj&apos;icient was negative. Possible reasons for this anomalous behavior are briefly discussed. In recent years it has been found that the region close to the surface of a metal can sometimes exhibit anomalously slow diffusion characteristics relative to the interior of the metal. One of the best examples of this fact is the work of Styris and omizuka,&apos; who showed that the apparent diffusion coefficient for zinc in the region withi: about 1 p of the free surface of copper was about ,,,, that at deeper penetrations. This result is particularly interesting, because it is free from the possibly complicating effects of low solubility of the diffusing tracer in the solvent metal. In the case of diffusion under conditions of low solubilitjr, interpretaticn of the results in terms of lattice diffusion is difficult because of the enhanced short-circuiting produced by segregation to dislocations.2&apos;3 Measurements by Duhl et 1. suggest that cobalt diffusing in gold may also show a near-surface effect of this type. Once again the solubility is high, so that this result could be of great interest. However, the technique used for analyzing the diffusion penetration zones by Duhl, viz. the counting of residual gamma activity in the specimen following sectioning, appears to have indicated a near-surface effect in a parallel experiment on the self-diffusion of gold reported at the same time. The latter result is known to be spurious, since Kidson5 has demonstrated that self-diffusion in gold does not show this effect. Duhl et 01. also reported some measurements on the diffusion of nickel in gold, but failed to give any data for the near-surface region. As the solubility of nickel in gold is high, such data would also be of special interest. We, therefore, decided to conduct another set of experiments on the diffusion of nickel and cobalt in gold, using a sectioning technique that allows the individual sections to be assayed for solute content and thus gives direct determinations of penetration profiles. Also, by sectioning with an anodizing/stripping tech- nique, very thin layers can be removed and the region close to the surface studied in detail. MATERIALS The gold specimens were supplied as single crystal disks $ in. in diam by a in. high by Monocrystals Co. of Cleveland, Ohio. The gold itself was of spectro-scopic purity, i.e., better than 99.99 pct pure. METHOD Specimen Preparation. One flat end face of each gold crystal was spark planed with a Servomet spark erosion machine set for minimum spark energy. Following this treatment the crystals were preannealed for 2 to 4 days at temperatures of either 400" or 700°C. The three crystals preannealed at 700°C showed signs of recrystallization. The spark-planed end face of each crystal was then coated with the appropriate amount of 63i or 60 radioactive tracer. This deposit was laid down in a simple plating bath containing the as-supplied solution of the radioactive isotope as well as sufficient ammonium oxalate to saturate the solution. Some ammonium oxalate remained undissolved on the floor of the bath for this purpose. During plating further additions of ammonium oxalate were sometimes required to allow the plating to continue satisfactorily, perhaps due to passivation of the undissolved oxalate already present. The thickness of the deposited layer was determined by comparison of the apparent surface activity of the plated specimen with that of a similar specimen having a weighable deposit of the isotope on its end face. Correction for self-absorption of the radiation was made in this calculation. Annealing. The deposited crystals were annealed in a hydrogen atmosphere in sealed silica tubes. During this heat treatment they were supported, active face down, on optically flat silica plates. The temperature was measured with calibrated Pt vs Pt-10 pct Rh thermocouples, and the tabulated values can be taken to be correct to Z°C. All the crystals showed evidence of recrystallization following these heat treatments, suggesting that initially they may not have been good single crystals or had suffered strain during delivery. Concentration Profile Analysis. After annealing, the crystals were sectioned by the anodizing-stripping technique.6 The anodizing involved suspension of the specimen with its cylindrical axis horiz6ntal by a gold wire in a 200-ml beaker containing 1 M Hg304. A cathode in the form of a strip of gold sheet, 2 in. wide and positioned to be in contact with the curved side of the beaker, completely encircled the specimen. An anodizing current of 30 ma, corresponding to a current density of 5 ma per sq cm on the surface of the specimen, was passed for times ranging from 5 to 150 min depending on the thickness of gold to be removed; the solution was stirred continuously during this process. Following this treatment, the specimen

Jan 1, 1969