Search Documents

By J. Simmons, P. Ziemkiewicz

Acid-Base Accounting (ABA) is an analytical procedure that provides values to help assess the acid-producing and acid-neutralizing potential of overburden rocks prior to coal mining and other large-scale excavations. This procedure was developed by West Virginia University scientists during the 1960s. After the passage of laws requiring an assessment of surface mining on water quality, ABA became a preferred method to predict post-mining water quality,and permitting decisions for surface mines are largely based on thevalues determined by ABA. In order to predict the post-mining water quality, the amount of acid-producing rock is compared to the amount of acid-neutralizing rock, and a prediction of the water quality at the site (whether acid or alkaline) is obtained. We gathered geologic and geographic data for 56 mined sites in West Virginia, which allowed us to estimate total overburden amounts, and values for maximum potential acidity (MPA), neutralization potential (NP), net neutralization potential (NNP), and NP/MPA ratios for each site based on ABA. These values were correlated to post-mining water quality from springs or seeps on the mined property. Overburden mass was determined by three methods, with the method used by Pennsylvania researchers showing the most accurate results to actual overburden mass. A poor relationship existed between MPA and post-mining water quality, NP was intermediate, and NNP and the NP/MPA ratio showed the best prediction accuracy. In this study, NNP and the NP/MPA ratio gave identical water quality prediction results. Therefore using NP/MPA ratios, values were separated into categories: <1 should produce acid drainage, between 1 and 2 can produce either acid or alkaline water conditions, and >2 should produce alkaline water. On our 56 surface mined sites, NP/MPA ratios varied from 0.1 to 31, and six sites (11%) did not fit the expected pattern using this category approach. Two of eight sites with ratios <1 did not produce acid drainage as predicted (the drainage was neutral), and four of 40 sites with a ratio >2 produced acid drainage when they should not have. These latter four sites were either mined very slowly, had non-representative ABA data, received water from an adjacent underground mine, or had a surface mining practice that degraded the water. In general, an NP/MPA ratio of <1 produced acid or neutral drainage sites, between 1 and 2 produced mostly alkaline drainage sites, while NP/MPA ratios of >2 produced alkaline drainage with a few exceptions. ABA is a good tool to assess overburden quality before surface mining and to predict post-mining drainage quality after mining. The interpretation from ABA values was correct in 50 out of 52 cases (96%), excluding the four anomalous sites, which had acid water for reasons other than overburden quality.

Jan 1, 2003

By Stanley I. M, Brett D, Dickson R

The Mt Lyell Mine, situated in Queenstown on the west coast of Tasmania, has a production history of more than 100 years. Previous mining activities have resulted in substantial modifications to environmental conditions at Mt Lyell and disposal of sulphidic waste rock across the lease has left a legacy of on-going environmental impacts including acid drainage (AD). In 1995 Copper Mines of Tasmania (CMT) was granted a mining lease Irons the Tasmanian State Government for redevelopment of Mt Lyell and indemnity from actions concerning pollution from previous occupation and use of leased land. The Environmental Management Plan (EMP) for the Mt Lyell redevelopment committed CMT to be responsible for waste rock dumps generated from their activities and to ensure that management is in-line with best practice environmental management principles. CMT commenced commercial production in December 1995 with sulphidic material from development of the underground Prince Lyell mine reporting to a single waste rock dump constructed according to a management plan developed in July 1995 and superseded by a management plan for extension in May 1997. The CMT waste rock dump currently has a total capacity of 220 000 m- and approximately 120 000 m3 of rock have been placed to-date. Material reporting to the dump is placed in a densely compacted state to a controlled surface profile. The dump is clay capped and a final revegetated soil layer placed on top. A rock pitched drain extends down to a wetland area in order to remove stormwater and minimise possible soil erosion on the revegetated sections. An integral part of the management plan for the waste rock dump involves characterisation of waste rock to identify geochemical rock types according to acid forming potential with provision for selective placement within the dump. High-risk materials are selectively placed and covered within the core of the waste rock dump, where possible, to control sulphide oxidation. Monitoring equipment has been installed in the waste rock dump by the Australian Nuclear Science and Technology Organisation (ANSTO) and an on-going monitoring program has been established to demonstrate the integrity of the dump cover as a barrier to the influx of atmospheric oxygen into the dump. The overall objectives of this program of work are to control the oxidation of sulphidic waste rock in the waste rock dump, minimise the risk of AD, prevent pollution of the aquatic environment and thereby demonstrate the integrity of the CMT waste rock dump management Strategy.

Jan 1, 1997

By F. W. C. Boswell, R. L. Cunningham, H. M. Weld

Chemical analysis shows the partition of the magnesium addition between the metal and the graphite is independent of whether the graphite is in the form of nodules or flakes. The bright central spot observed in nodular graphite polished sections is shown to be due to the structure of the nodules. DURING the past few years numerous papers have been published on the production1-7 and heat treatment" of nodular cast irons. However, very little information is available on the structure of the nodules and the reason for their formation. It would appear that an explanation of the phenomenon of nodulation must await a detailed knowledge of the nature of the nodule. Disagreement exists among various workers on such a fundamental point as to whether or not a nodule actually contains a microscopically visible, nongraphitic nucleus.9-11 Work was initiated with a view to obtaining definite information on this and other aspects of the problem. Chemical Separation and Analysis Microscopic appearance had indicated9-11 that a nongraphitic core might exist in nodules (Fig. 1). It appeared that a chemical comparison of separated nodules and flake graphite would be profitable, for if the core is nongraphitic a relatively large amount of certain elements would be found in the nodules as compared to the flake. This comparison could best be made by obtaining nodules and flake from the same melt of cast iron, part of which had been in-noculated with a suitable addition reagent for the formation of nodules. A 300 lb melt was produced. About half of this was innoculated in the ladle with an Fe-Si-Mg alloy to produce nodules and cast into keel blocks; the remaining half of the melt had silicon added in an effort to compensate for the silicon in the innoculant used in the other half of the melt and this was cast into similar keel blocks. The analyses of the resultant irons are given in Table I. Nodules and flake were chemically extracted from 2 kg samples of metal as described in the appendix. While this method dissolved the iron and chromium carbides, it did not dissolve the titanium, vanadium, and molybdenum carbides. These latter carbides could have been removed by nitric acid, but in other experiments it was found that it attacked pools of metallic iron entrapped in the nodules which had, until the nitric acid treatment, been protected from the attack of the sulphuric, hydrochloric, and hydrofluoric acids. It will be shown in the next section that entrapped iron exists in nodules but not in flake. On microscopic examination many tiny irregular particles were observed to accompany both the nodules and the flake. These were identified by tabling a sample of nodules from which a sufficient fraction was obtained for X-ray analysis. A good pattern of titanium carbide was obtained indicating that this was the predominant compound present. Since it was not possible to determine how completely the carbides could be removed mechanically and since their removal from flake is much more difficult, it was decided not to resort to any separation as this would render further comparisons more difficult. The samples were ashed in a combustion

Jan 1, 1953

By K. Barron

The glass insert stressmeter, or photoelastic stressmeter, is an instrument designed to determine stress changes occurring in rocks. It has several potential advantages over other such devices in that it is a biaxial device, it is simple and it is cheap to make. The object of this study was to assess the behaviour of the meter under biaxial loads and to examine some of the problems associated with measurement and interpretation of the fringe pattern. This assessment has been carried out by comparing theoretical and laboratory behaviour of the meter. It has been shown that: a) There are certain optimum measuring points in the meter at which measurements should be made for best accuracy. The position of the points depends on the ratio, n, of the biaxial stresses. b) The meter&apos;s sensitivity can be assumed to be independent of the rock modulus E provided that the rock modulus is < 2.5 x 106 psi and not, as previous workers have assumed, if E < 5 x 106 psi. c) There are several methods of separating the principal stresses; some of these are unsatisfactory. A new method is proposed and discussed. d) The meter sensitivity decreases as the ratio of the biaxial stresses approaches unity; the accuracy thus also decreases. e) The axes of symmetry of the fringe pattern give an excellent indication of applied stress direction. f) Laboratory calibrations are in good agreement with theory. The glass insert or photoelastic stressmeter is an instrument designed to determine stress changes occurring in rocks. It has several potential advantages over other such devices in that it is a biaxial device, it is simple and it is cheap to make. This stressmeter has been described in detail.l,2 Basically it is a hollow glass cylinder that has at one end a light source and filters producing circularly polarized light. The glass cylinder and source are grouted into a borehole in rock and the face of the cylinder is viewed through a quarter wave plate and an analyser. If, after installation, a stress change occurs in the rock, then a distinct colored isochro-matic fringe pattern is seen in the meter. The fringe order at any point in the meter can be determined by counting the fringes and measuring the fractional fringe orders by the Tardy compensation method. The relation between the fringe order at any point and the applied stress change can be determined either by calculation or by calibration. The object of this study was to assess the behavior of this stressmeter under biaxial loading conditions and to examine some of the problems of interpretation of the fringe pattern. THEORY Hiramatsu et a14 have determined the stress distribution in a hollow cylindrical inclusion in an elastic host material when subject to uniaxial stress. Using this solution, the biaxial case of stress p in the x direction and stress q in the y direction (Fig. 1) can be solved by superposition. This has been done in Appendix 1. It is shown that the principal stress difference (s1 -s2) at any point (r,?) in the cylinder is given by:

Jan 1, 1965

By Jr. Flynn

"The Bureau of Mines receives and answers many requests for information on the qualities and properties of American coals, and also publishes many papers that deal with coal characteristics. Compilations of chemical analyses of coal from specific locations are contained in a series of technical papers,2/ by States, whereas typical analyses of coal seams, by States and counties, are given in data books, volumes 1 to 7,2/ by producing districts, as defined in the Bituminous Coal Act of 1937. Bulletin 446, ""Typical Analyses of Coals of the United States,"" condenses and supplements these data books, which do not apply to the Western States. Other coal properties are described in numerous publications listed in the Bureau of Mines Bibliography of Publications. However, no recent publication lists average B.t.u. values by rank on a Statewide and national scale. Averages have been estimated in the past, and some of them are included in this paper for comparison.The average and the ranges of as-received B.t.u. values of American coals on a Nation-wide basis, as found by the statistical method described in this paper, are given in table 2 and on a State-wide basis in table 3. The following is abstracted from table 2:In deriving average B.t.u. values for coals, the results depend on the type of data available and the methods of calculation. The data, or analyses, may represent any of three types of samples - mine, tipple, or delivered. In mine sampling, a channel cut is made of a vertical face of the coal bed, carefully excluding most of the impurities, and the material retained is the sample. It is readily seen that mine samples are selected samples and do not strictly represent the unmined coal bed, unless the coal contains no major impurities. Mine samples generally represent the best-quality coal that could be produced. In contrast to mine samples, tipple and delivered samples represent coal that actually has been mined, and their analyses may show either lower or higher values than mine samples of the same coal, depending on treatment and preparation after mining.Of the thousands of analyses accumulated by the Bureau of Mines, most are of either tipple or delivered samples and represent the coal after it has been mined. Any average calculated from this aggregate of data will, consequently, reflect coal that has been produced, and not unmined coal in situ.The method of calculating an average from the basic data also will have considerable influence. If there are three seams of coal in a county, the average analysis for the county is not necessarily the arithmetic mean of analyses of the three individual seams. For a probable average of unmined coal, the B.t.u. values of each seam should be weighted in proportion to the unmined reserves of each seam. In similar manner, an average for past pro¬duction should be weighed according to the past production for each seam. Figures for coal reserves are only estimates based upon geologic evidence and its interpretation. Production records are much more accurate than estimated reserves, although detailed production records for individual seams by counties are very few."

Dec 1, 1949

By John T. Norton, R. E. Hiller

The tremendous increase in the use of metals that have been prcpared by the various cold-working processes during recent years has greatly stimulated the investigation of problems concerned with the fundamental nature of these processes. It has been observed in practice that different methods of bringing about the same dimension changes in a sample result in a rather wide range of properties. Cold working reduces the ductility of a metal, or what is perhaps more nearly correct, its "working capacity," and naturally the manufacturer wishes to produce an article that has as large a working capacity as possible, and to produce it with the smallest number of operations. It has also been known for some time that cold deformation produces a parallel alignment of the crystal grains of a metal, and that the type of this preferred orientation depends to some extent at least upon particular processes employed in the deformation. The present investigation has for its purpose the study of the relations between the various factors of a cold-working process and the preferred orientation of the metjal crystals resulting from this deformation. The work is chiefly confined to a study of cold-drawn seamless tubing. Preparation of Samples The tubing samples used in this investigation were made of steel having a carbon content of 0.10 to 0.20 per cent, and were drawn on a standard type of draw bench. In order to obtain the large reductions, the annealed stock was coated with lead, for purposes of lubrication. The reductions of area stated refer to reduction from the annealed condition without intermediate heat treatment. The cold work was done as nearly as possible at room temperature. The samples of wire and strip used for purposes of comparison were of steel of approximately the same carbon content and were prepared in the manner indicated. X-ray Method of Investigation The condition of preferred orientation in cold-worked samples is best investigated by the X-ray method that employs a small circular beam of * Assoriate Professor of Physics of Metals, Massachusetts Institute of Technology. t Graduate Student, Department of Metallurgy, Massarhusetts Institute of Technology.

Jan 1, 1932

By Max Mason

IN 1923 a Western mining company was experimenting with the device of an inventor designed to locate buried ores by radio. Because the progress was slow and the results were confusing, the company began to doubt the usefulness of the method and invited me to review the whole question of the application of physics to ore detection. I was fortunate in securing the cooperation of several physicists who had worked with me during the war on the problem of submarine detection. This group has been increased and has been studying the problem of physical exploration for ores since that time. It was evident that the problem is a big one, with many angles of approach. Its general features may be set down, in rough outline, as follows: The soils, rocks and ores hidden beneath the surface differ, one from another in many respects. These differences may be made to furnish a clew for the physicists working from the surface. To bring these differences into action the physicist creates some kind of an effect, which penetrates into the ground and is distorted and, reflected when it meets boundaries between different sorts of underground structure. In other words, he sends a message down, and the rocks and ore send back signals in, reply. In picturing this process, we should not regard the ground as dense and impenetrable. The kind of messages used pass through the earth about as readily as a sound wave travels the air. If, then, the fundamental procedure is to shout down questions in the hope that an orebody will hear and answer back to us, it is clear that a large part of the expert&apos;s study must relate to the kind of questions best suited to the temperament and intelligence of orebodies. It will be easier for the ore to, reply to some of our questions than to others, and it is for us to find the right questions. In certain cases, we are-spared the necessity of using a messenger, because nature has already provided one. For example, we already have a terrestrial magnetic field which auto-matically and continually conveys messages from underneath. We also have available the earth&apos;s gravitational field which furnishes us

Jan 1, 1927

By Max Mason

IN 1923 a Western mining company was experimenting with the device of an inventor designed to locate buried ores by radio. Because the progress was slow and the results were confusing, the company began to doubt the usefulness of the method and invited me to review the whole question of the application of physics to ore detection. I was fortunate in securing the cooperation of several physicists who had worked with me during the war on the problem of submarine detection. This group has been increased and has been studying the problem of physical exploration for ores since that time. It was evident that the problem is a big one, with many angles of approach. Its general features may be set down, in rough outline, as follows: The soils, rocks and ores hidden beneath the surface differ one from another in many respects. These differences may be made to furnish a clew for the physicists working from the surface. To bring these differences into action the physicist creates some kind of an effect which penetrates into the ground and is distorted and reflected when it meets boundaries between different sorts of underground structure. In other words, he sends a message down, and the rocks and ore send back signals in reply. In picturing this process, we should not regard the ground as dense and impenetrable. The kind of messages used pass through the earth about as readily as a sound wave travels the air. If, then, the fundamental procedure is to shout down questions in the hope that an orebody will hear and answer back to us, it is clear that a large part of the expert&apos;s study must relate to the kind of questions best suited to the temperament and intelligence of orebodies. It will be easier for the ore to reply to some of our questions than to others, and it is for us to find the right questions. In certain cases, we are spared the necessity of using a messenger; because nature has already provided one. For example, we already have a terrestrial magnetic field which auto-matically and continually conveys messages from underneath. We also have available the earth&apos;s gravitational field. which furnishes us

Jan 1, 1927

Meeting, Aug. 20, 1913, B te, Montana, at 12.45 p.m.-On, the written request of 27 members of oft Institute residing in Montana, the Montana Local Section was established, and the following Committee was appointed by the President of the Institute to complete the organization : E. P. Mathewson, Chair pan; Frank M. Smith, Vice-Chairman; D. C. Bard, Secre-tary, Montana State School of Mines, Butte, Mont., Oscar Rohn, James L. Bruce. The President reported the appointment of a Committee on Mining Law, the names of whose officers and members are given on page xxxv of this Bulletin, and these appointments were approved. It was voted: That the Committee on dining Law be requested to establish a Sub-Committee on Censorship, a majority of whom shall be lawyers; and, further, that no paper on mining law be recommended for publication to the Committee on Papers and Publications, unless it is previously approved by the Sub-Committee on Censorship of the Committee on Mining Law. The President reported progress in the matter of co-operation between the Institute and the United States Bureau of Mines, through Committees of the Institute. The President reviewed the history of plans for a union or affiliation with the Mining and Metallurgical Society of America, and the following minute was then adopted : " The Board of Directors of the American Institute of Mining Engineers has carefully considered for several months the question of union or affiliation with the Mining and Metallurgical Society of America ; and, while at an earlier time and under other circumstances, such. a union might have been accomplished, yet under present circumstances the Directors of the Institute deem such union inexpedient. "While thanking the Mining and Metallurgical Society of America for its consideration of the matter, we believe that further discussion of the subject will serve no useful end, and we conclude it best that the Society and the Institute continue their useful functions and friendly relations side by side, as heretofore."

Jan 10, 1913

By F. M. Stewart

A paper by Hurst and van Ever-dingen in 1949 led to the practical solution of many nonsteady-state flow problems.&apos; Subsequently, applications of this material have been discussed by several authors. The purpose of this note is to outline a simplified direct procedure for water-influx pressure predictions for pressures above the bubble point. The prcposed procedure is unique in that after the "time-conversion factor" and the "influx constant" are obtained, predictions are made without trial and error. The elimination of trial and error is made possible by expressing certain PVT characteristics as explicit functions of pressure. The procedure is applicable to fields producing at pressures above the bubble point and under radial water drive from an infinite aquifer. In the usual applications it is required to predict (1) withdrawals given future pressure history or (2) reservoir pressure, given future withdrawals or production. The theory, assumptions and conditions under which the nonsteady-state solutions hold are covered in the references and are not repeated. The simplified direct procedure outlined here has been developed from published solutions for the so-called "pressure case". A similar direct procedure for the same special conditions has been developed for the "rate case"; however, in this instance the procedure is lengthy and offers no advantage over the trial-and-error solution. Consequently, this paper covers only the procedure based on the pressure case. DISCUSSION Under the pressure case prediction of withdrawals from a water-drive field, given the future pressure history, involves the use of a nonsteady-state water-influx term together with the material balance equation. The solution of a particular problem requires the following steps: (1) division of past pressure and production data into equal time intervals; (2) computation of cumulative water influx vs pressure drop for each time interval of past history using the material balance equation; (3) determination of the best values for the "time-conversion factor" and the "influx constant" by equating the nonsteady-state influx term with the influx computed in Step 2 (this requires a trial-and-error procedure); (4) prediction of influx for a given pressure drop using the influx term and the computed factors from Step 3; and (5) calculation of fluids produced using the predicted influx in the material balance equation. A forecast of the water-oil ratio or water production rate is required to complete the calculation. It is assumed that a reliable estimate of original oil in place is available, as well as the production and pressure history, and data on reservoir fluid characteristics. If the original oil in place is unknown, it may be computed simultaneously with the tinie-conversion influx factors2,3. However, the oil in place so computed may be considerably in error3; consequently, it is usually preferable to use oil in place estimated from pore-volume data unless there is considerable doubt as to its accuracy. The Material Balance Equation Above the Bubble Point Above the bubble point the simpli-

By J Morton

The Resource Management Act 1991 represented an innovative and unique piece of planning and environmental legislation when it was introduced. Since the Act was passed into law in 1991 it has been subject to nine amendments, many of which were of the ætinkerÆ variety. These amendments recognise that the Act has not been as successful in providing the æone-stop shopÆ for resource users that the Act was hoped to be. The latest and most significant attempt at changing the Act was the Resource Management Amendment Act 2003. The amendments made by the Amendment Act have proved to be largely unsuccessful in achieving any significant changes to the way resources are managed in New Zealand, and have failed to address many of the concerns which drove the original Resource Management Amendment Bill in 1999. The recent decision to discontinue further investment in Project Aqua has once again placed the Act in the spotlight as a significant hand-brake on major projects. This particular event has led to yet another review to be undertaken this year. The review will focus on five key areas: &nbsp; 1.&nbsp;&nbsp; achieving the right balance of national and local interests; 2. &nbsp; improving the design and process for local policy formulation; 3. &nbsp; improving the consent decision making process; 4. &nbsp; allocation of natural resources (water, air and geothermal); and 5. &nbsp; supporting measures for building capacity and promoting best practice and implementation at the local authority level. &nbsp;It is important for the business community and the mining industry in particular to seize the opportunity that this review provides to make sure that any amendments undertaken as a result of the review achieve the aims listed above. The review needs to be considered in light of the current regime for the management of natural resources in New Zealand. In addition to the Resource Management Act 1991, the Crown Minerals Act 1991 and the Building Act 1991, which form the core resource statutes in New Zealand, there have been other developments affecting the regime. Special legislation over and above the Resource Management Act 1991 has been enacted to protect the Hauraki Gulf and special legislation is currently being considered to protect the Waitakere Ranges in Auckland. In the Hauraki District mining is prohibited in some areas and a plan change mechanism is specified as the appropriate tool to use in the event a mineral resource is to be developed in those areas. The current review is a further opportunity to remedy the inadequacies of the Act.

Jan 1, 2004

THIS paper presents briefly some of the principal results of 3 ½ months field work during the summer of 1938 in the Chichagof mining district, southeastern Alaska. The report is preliminary and presumably will be followed later by a more complete report to be published by the Geological Survey. The paper is concerned principally with the structural geology of a block of steeply dipping graywacke as revealed underground in the Hirst Chichagof and the Chichagoff mines, the two principal mines of the district. The two mines have produced about $16,000,000 worth of gold and silver. The attitude of the graywacke, which is locally cut by dikes and sills of aplite, is remarkably uniform and trends about N. 62º W. The average dip is about 67º SW. The graywacke is cut by large faults, the best known of which are the Hirst and the Chichagof, whose average trends are about N. 30ºW. and average dips about 75º SW. The faults at some places split into the bedding of the graywacke and at others are deflected from their normal trends for considerable distances along the bedding. The relative movements along the faults was northwest and up at about 30º for the south- west or hanging-wall sides. The ore bodies are elongate quartz lenses in the faults. Most of the quartz is mineralized but locally large quartz masses are too low grade to be mined. The emplacement of the ore bodies appears to have been structurally controlled in large part by the intersections of the faults with the bedding surfaces. Places where the faults split or are deflected appear to have been particularly favorable places for ore deposition. There has been some post-quartz movements along the faults but it is thought that such movements have not been extensive enough to greatly modify the original positions and shapes of the ore bodies.

Jan 1, 1939

By F. M. Lewis, J. F. Myers

The selection of the proper type of flotation machine involves the consideration of a wide variety of factors. Under any condition, all types of machines will promote some kind of separation. Obviously, the correct way of deciding which type of machine is best suited for a particular problem would be to set up all types of machines and test them out in a competitive manner, but the vast number of small concentrating plants are unable to make such complete and exhaustive tests. The experience of the authors of this paper indicates that if all the factors involved in any particular problem can be determined, and if all the flotation-machine characteristics are understood, some basis for selection could be arrived at other than actual comparison. This paper is presented to show how the process factors and machine characteristics have been combined at the mills of the Tennessee Copper Co. from studies of several types of flotation machines. At the two mills of the Tennessee Copper Co. in the Ducktown Basin of Tennessee, four distinct flotation separations are made on the complex sulphide ore. Three different concentrates are produced from the ore—in the order of their importance: iron concentrate, copper concentrate, and zinc concentrate. Four different types of flotation machines are used. The selection of these four machines, for the plant operation, was based upon the study and operating experience of the machine units shown in the following list: Fagergren machine; square cell, size 56 inches Fagergren machine; level type, size 56 inches Denver machine; conical disk impeller, size 24 inches Denver machine; receded disk impeller, size 24 inches Minerals Separation Sub-A, size 24 inches Munro-Pearse deep cell, pneumatic Southwestern air machine, Hunt principle To date the study of flotation machines has been confined almost entirely to the rougher circuits. The various cleaning operations, being relatively a much simpler matter, have not been investigated so thoroughly. Table I shows a typical analysis of the two ores as well as of the mineral content.

Jan 1, 1947

By J. F. Myers, F. M. Lewis

The selection of the proper type of flotation machine involves the consideration of a wide variety of factors. Under any condition, all types of machines will promote some kind of separation. Obviously, the correct way of deciding which type of machine is best suited for a particular problem would be to set up all types of machines and test them out in a competitive manner, but the vast number of small concentrating plants are unable to make such complete and exhaustive tests. The experience of the authors of this paper indicates that if all the factors involved in any particular problem can be determined, and if all the flotation-machine characteristics are understood, some basis for selection could be arrived at other than actual comparison. This paper is presented to show how the process factors and machine characteristics have been combined at the mills of the Tennessee Copper Co. from studies of several types of flotation machines. At the two mills of the Tennessee Copper Co. in the Ducktown Basin of Tennessee, four distinct flotation separations are made on the complex sulphide ore. Three different concentrates are produced from the ore—in the order of their importance: iron concentrate, copper concentrate, and zinc concentrate. Four different types of flotation machines are used. The selection of these four machines, for the plant operation, was based upon the study and operating experience of the machine units shown in the following list: Fagergren machine; square cell, size 56 inches Fagergren machine; level type, size 56 inches Denver machine; conical disk impeller, size 24 inches Denver machine; receded disk impeller, size 24 inches Minerals Separation Sub-A, size 24 inches Munro-Pearse deep cell, pneumatic Southwestern air machine, Hunt principle To date the study of flotation machines has been confined almost entirely to the rougher circuits. The various cleaning operations, being relatively a much simpler matter, have not been investigated so thoroughly. Table I shows a typical analysis of the two ores as well as of the mineral content.

Jan 1, 1947

By R. B. Gordon, D. A. Koss

Ultrasonic-atlenuation changes due to the formation of free dislocations have been observed during tensile tests of magnesium and LiF single crystals and samples of polycrystalline Results on the LiF and samples are similar: A preyield attenzration increase is observed which, however, be-corlzes smaller as the magnitude of the drop in load al yielding increases. This indicates that the yield point observed in these materials is due to dislovation rather than dislocation unpinning and that the initial density &apos; free dislocations must be low if the yield point is to be sharp,. Tests on the magnesium ere conducted at both 27" and 200C. Magnesium has the unusual property that the yield drop is larger at the higher test temperature and is accomplished by a decrease in attenuation. The latter is due principally to the temprovary pinning of detained dislocations by highly solute atoms. After strain aging., a stress as low as 0.3 bur suffices to unpin dislocations; microstrain measuements of sufficient sensitivity should. reveal plastic flow at stress levels this low IN another paper,&apos; we describe the technique of simultaneously observing ultrasonic-attenuation changes and plastic microstrain during deformation of spher-oidized carbon steels. Changes of ultrasonic attenuation indicate damping effects caused by the oscillation of long, freely moving dislocation segments. Simultaneous microstrain measurements are used to indicate total dislocation motion. The dislocation-damping observations are most useful in the study of the early stages of deformation where the dislocation density is low and the plastic strain is small and relatively difficult to measure. Particularly interesting results are found in materials which display sharp yield points. Observations of these phenomena are reported here for three materials: single-crystal LiF and magnesium, and poly crystalline molybdenum. EXPERIMENTS Dislocation-damping effects were observed by measuring changes in acoustic attenuation with the ultrasonic-pulse method. The end faces of each of the specimens were ground flat and parallel and a quartz 10 Mc per sec, x-cut transducer was attached to one face. The bonding agents used were: a) "Nonaq" stopcock grease with magnesium, b) beeswax with LiF, and c) salol with molybdenum. With the LiF, the best acoustic signals were obtained at 45 and 50 Mc per sec; all other measurements reported are at 10 MC per sec. The Sperry Ultrasonic Attenuation Comparator2 was used to measure attenuation changes. In the

Jan 1, 1967

By R. T. DeHoff

Saltykov&apos;s meihod for the determination of the size distribution of spherical particles from measurements made on random plane sections is extended to particle shapes which are not equiaxed. The analysis permits the deterrrzination of the size distribution of aggregates of ellipsoidol particles provided all particles have tlze same shape. V ARIOUS solutions to the problem of the determination of the size distribution of spherical particles from measurements made on random plane sections have appeared in the literature since the original solution was first published by Scheill in 1934. Solutions have been offered utilizing measurements of the diameter1y2 or area3&apos;4 of circular sections that result when a test plane is passed through an aggregate of spherical particles, and the length of intercept5y6 that results when a test line is passed through the aggregate. To the best of the knowledge of the author, no method has been proposed which permits the determination of the size distribution of particles that are not equiaxed. The purpose of this paper is to develop a method which permits the determination of the size distribution for a specific class of particle shapes which cover awide range of axial ratios; namely, ellipsoids of revolution. In the interests of simplicity, it is necessary to limit consideration to aggregates of particles which are all similar in shape; that is, the ellipses which, by rotation about one of their axes, generate the particles, all have the same axial ratio. The size distribution, which is to be determined by the analysis, is arbitrary. It is also assumed that the section, or sections, upon which the measurements are made represent the average of all possible sections through the structure. This ideal condition can be approached as nearly as may be desired by observing a sufficient area of sections taken at random positions in a randomly oriented aggregate, and in random positions and orientations in an aggregate that has one or more axes of orientation. SIZE DISTRIBUTION FOR PROLATE ELLIPSOIDS Consider an aggregate of cigar shaped, geometrically similar particles (prolate ellipsoids), dispersed in an opaque matrix. Let the size of each particle be specified by the length of its minor axis, By Fig. 1, and the shape, q, be defined by the ratio of its minor to its major axis, B/A. Let the index, j, refer to dimensions of ellipsoids in a particular size class, and the index, i, to dimensions of an ellipse resulting from the intersection of a test plane and a particle. The size of such a section is specified by the length of its minor axis, b. Let the particles be arbitrarily divided into k size classes, and let the increment of size between each class be A, where A = &,$, B,,,being the minor axis of the ellipsoids in the largest size class. Since all sections are represented on the test plane, the minor axis of the largest of the sections observed, results from the intersection of the test plane with an ellipsoid in the largest size class at its center, and is therefore equal to Bmax Thus the increment, A = The final result will consist of the k numbers which represent the number of particles in each size class per unit volume of aggregate:

Jan 1, 1962

By Peter J. Szabo

INTRODUCTION The time period from the detailed feasibility study to the post investment audity usually ranges from three to eight years depending upon the nature of the mining project considered. It is the only after the post investment audit that we know the adequacy of the assumptions made concerning operational risk assessment in the detailed feasibility or acquisition economics. The post investment audit results from numerous mining projects can best be described by a verse by John Greenleaf Whittier&apos;s Maaud Muller. It reads "For all sad words of tongue or pen the saddest are these &apos;It might have been!"&apos; Dissecting the negative results of numerous mining projects we find faulty assumptions concerning markets, geology, capital investment and operational risk assessment. Although in hindsight many of these assumptions could have been considered impossible or impracticle to have forecast with any degree of certainty, we find that refined assumptions concerning operational risk assessment could have been made with only a modicum of additional "Due Diligence". Anyone who invests in a mining property should employ a much higher discount rate of future cash flow, (usually in the minimum range of 25%-30%), than he would expect from such safe investments as Treasury Bills or high grade Utility Bonds. The nature of this steep discount translates to a large uncertainty concerning the timing and actualization of assumptions contained in the detailed feasibility study. We must remember that when a project gets beyond 20 years, any contribution to the value of the project of cash flow is minimal due to the nature of the discounting process. Thus for each full or partial day lost in the development or early operation stage of a project, the financial impact will be greater than similar lost days later on in the project. Adequate operational risk assissment is particularly critical when bidding on competitive tenders for coal deposists in remote locations such as the Bowen Basin in Queensland, Australia. Because of the market attractiveness of these coal deposits for supplying end users in the Far East, Middle East and Europe, state governments require competitive tender biddings via the Authority to Prospect process. Front end bonuses and super royalty payments must be commited before the actual mining conditions are known. Time to submit firm offers from the actual request for proposal vary from 90 to 120 days. Thus any operational risk assessment must be detailed, realistic and reflective of the actual project. When one searches the literature, one finds limited qualitative data on operational risk assessment in valuation papers. Usually this facet of valuation takes a secondary role to such areas as reserves, markets, and environmental considerations. When one comes to the question of operational risk assessment more often than not one finds the use of "rules-of-thumb", such as tons per man shift, average production, average seam height, etc., are used to forecast results on which banks and other financial institutions are required to make investment decisions. Because of the extremely competitive environment of the 1970&apos;s and 1980&apos;s numerous financial institutions approved loans without adequate "Due Diligence", and are currently paying a steep price in terms of non performing loans and charge offs. One must always remember that each operation is unique with its own characteristic

Jan 1, 1985

By Henry Drinker

The Institute has lost a valued member by the death of Eckley B. Coxe, Jr. He bore the name of one who was largely instrumental in founding the Institute, and to whose support and guidance as active member, Vice-President, and President, the Institute owes. much. Eckley B. Coxe, Jr., was the nephew of the late Eckley B. Coxe. He held a large interest in the coal estates owned and developed by his family, and he was thus naturally led to take a continuing interest in mining matters, and for years and up to the time of his death was a full member of the Institute. He died at his residence, Drifton, Pa., on Sept. 20 last, aged 44. He was a member of the class of &apos;93 of the University of Pennsylvania,. of which great institution he was a devoted alumnus. His educational and charitable activities were numerous, but his chief life-work and interest was in archeological investigation and research in Egypt, carried on through the Museum of the University of Pennsylvania of which Museum he was President. The discoveries made by the various expeditions financed and directed by him, and the notable publications issued by his direction and at his expense, chronicling the results, are among the most important researches ever made of buried Egypt. Mr. Coxe was a member of the International Historical Society and of many educational and charitable organizations. By his will, among other bequests, he left $500,000 to the Museum of the University of Pennsylvania and $100,000 to the University, the income of the latter fund to be applied to increasing the salaries of the professors of the Institution. He also left $100,000 to the Children&apos;s Hospital of Philadelphia, of which he was a manager, and in addition thereto $10,000 of which the income is to be applied in providing Christmas presents for .the child patients, and in providing an annual dinner for the patients and attendants of the hospital. He bequeathed $50,000 to Leonard Hall, an associate mission of the Episcopal Church, at South Bethlehem, Pa., $25,000 to the Epileptic Hospital and Colony Farm (Philadelphia) ; $50,000 to the Philadelphia Orthopaedic Hospital and Infirmary for Nervous Diseases; $15,000 to the United Charities of Hazleton, Pa., the income to be applied to the salaries of nurses; and $25,000 to the Mining and Mechanical Institute of the Anthracite Coal Region of Pennsylvania, founded by his uncle, Eckley B. Coxe, and of which Eckley B. Coxe, Jr., was an active trustee up to the time of his death. This Institute is known as one of the best preparatory schools for technical education in Pennsylvania, and is mainly devoted to extending an opportunity for education by day and night schools to the boys and young men of the Anthracite Region. Its principal is an alumnus of Lehigh University; it has an able local Board of Trustees, and an Advisory Board consisting of the Provost of the University of Pennsylvania, the President of Lafayette College, and the President of Lehigh University, all three of which institutions have established prize scholarships in the institute. Mr. Coxe carne of a distinguished ancestry, the record of which is fully given in the biographical notice of his uncle, Eckley B. Coxe, by Dr. R. W. Raymond, in Vol. XXV of the Transactions.`

Jan 12, 1916

By O. Cuscoleca

The Austrian plants at Donawitz and Linz were the first to blow steel with high purity oxygen. The paper shows how the process was developed and gives a survey of the results achieved to date. Compared with open hearth steel of equal quality, the obvious advantages of oxygen steel are the low investment and conversion costs. The nitrogen content of oxygen steel is not higher than that of good open hearth steel. Rimmed and killed steel products made by the oxygen process are superior to rimmed and killed steel products made by the best open hearth process. TWO new steel plants using the principle of making steel with high purity oxygen went into operation in Austria, one at Linz (Vereinigte oster-reichische Stahlwerke) in November 1952 and the other at Donawitz (dsterreichisch-Alpine Montan-gesellschaft) in May 1953. An estimated 330,000 metric tons were produced by the two plants in 1953, the first year of operation. In 1954 production by Austrian plants- using the high purity oxygen approach will be raised to 450,000 metric tons. This will be in addition to facilities in Huckingen (Man-nesmann A. G., Düsseldorf, Germany), those planned and under construction at Hamilton, Ontario, Canada (Dominion Foundries and Steel, Ltd.), and elsewhere. It is expected that by 1955 a total capacity of one million tons of high purity oxygen steel will be available. At the close of the last century, because of increasing availability of scrap, open hearth steel production forged ahead at an ever increasing pace. This caused world steel production to rise faster than pig iron production and finally to overtake it. In 1911 65 million tons of steel were produced against 64 million tons of pig iron. World steel production was 209 million tons in 1951, while pig iron output was only 147 million tons. The 1951 breakdown for steel shows 118 million tons made from pig iron, while the balance, 91 million tons or 44 pct of the total tonnage of steel produced, was made from scrap. This increase in crude steel production on a basis of high scrap consumption led to the world market scrap shortage and soaring scrap prices. In the United States and other nations, production of converter steel has fallen far behind that of open hearth steel. The surplus of processing scrap, un-absorbable by converting mills and thus a welcome source for open hearth and electric melting shops in the past, together with regular scrap purchases, no longer can meet requirements of both open hearth and electric steel production in Europe. In addition, recent modification of the basic bessemer process, blowing with oxygenated blast, substantially raised the scrap capacity of these plants. Any further expansion of world steel production will necessitate utilization of self-containing processes in regard to scrap because of the shortage.

Jan 1, 1955

By E. Heaton Hemingway

DURING the past year, the Watertown Arsenal has been interested in the occluded gas and oxide content of certain ordnance steels in order to determine, if possible, whether some of the peculiar failures in their physical properties might not be traced to these causes. For the purpose of best accomplishing a study of this nature, it was decided to heat the various samples of steel in a vacuum for definite periods of time at high temperatures and carefully examine the quantity and composition of the gases evolved. By the use of a fused quartz tube fitted with a water-cooled, ground-glass stopper, it was possible to maintain a vacuum at a temperature of 1000° C. for 10 hr. without perceptible leakage being evidenced as measured by a McLeod gage. The silica tube was connected with an evacuating system so constructed that the volatilized gases could be removed from time to time and a low vacuum of 0.002 to 0.0010 mm. of mercury continuously maintained. At no time during the period of heating or in the removal of the gases did the evacuated system come in contact with rubber stoppers or any rubber connections, making contamination from such a source impossible. In other words, the only volatile products that could be obtained must necessarily have come from the steel itself or from the glass and fused quartz system or from the mercury used as a sealing agent. In the earlier experiments, the steel treated was in the form of turnings, but this practice was discarded because the weights of the turnings before and after being heated were widely inconsistent, even when taken from the same piece of steel. This discrepancy developed largely through variation in the amount of metal volatilized with the gases; this metal could always be seen in the form of a ring where it condensed in the cooler portion of the tube either in the amorphous or crystalline condition. Because of the frequency in occurrence and the variation in the manner of deposition, this material was roughly analyzed and found to consist for the most part of iron. At the same time two samples of steel that had been

Jan 8, 1920