Search Documents

By Hjalmar W. Johnson

IT has long been accepted that blast-furnace practice varies to some degree with the coke used. While the qualities desirable in iron have been known for some time, the qualities in coke that produce such iron have not been established. There are no objective standards for blast-furnace coke, which is usually described in general terms, as good or bad. Many experienced operators believe that coke cannot be measured objectively except by using it in the furnace, noting the result, and labeling the coke according to furnace operations. This is admittedly unscientific, and besides is useless for the two main purposes for which a measure of coke quality is needed: (I) to produce the best possible coke from the coals and equipment on hand; (2) to test new coals and determine their value for blast-furnace coke. In seeking such an objective measure, much work has been done on tumbler tests, shatter tests, sizes of coke, porosity, specific gravity, reactivity or combustibility and other tests, but as yet very little has been published in which conclusive correlations have been established between such objective measures and furnace operation. In our study of the problem during the past 8 years we have developed no new measures of coke quality, but we have collected data that are presented here in the hope that they may assist in further work, so that at some future time there may be developed such positive measures. The purpose of this paper is to show that there are variations in coke and that such variations do influence the operation of blast furnaces. At the same time we must remember that there are variations in blast-furnace operation and it may be the blast furnace that is at fault. This correlation of coke properties with blast-furnace operation will be worked out in the following steps: I. Discussion of a period when a change in the coke resulted in an increase in efficiency on one furnace and a decrease in efficiency on another. 2. Adaptation of the inefficient furnace to the available coke so that normal efficiency was restored. 3. The use of radial distribution: a discussion of the effect of size of ore layer in adapting blast-furnace operation to the coke. 4. An example of a change in size of coke and the detrimental influence on the production of one furnace. 5. An example of a change in size of coke, together with manufacturing data, to show why it changed, the conclusion being that coke is a product with an optimum value. 6. Illustration of the fact that coke has different optimum values on two furnaces, with discussion on adaptation of operation so the optimum values will be the same. 7. Limitations of the use of screen tests as an objective measure of coke quality. 8. Importance of uniformity in coke. FUNCTIONS OF COKE AND QUALITIES REQUIRED TO PERFORM THESE FUNCTIONS Coke has three important functions in a blast furnace: (I) to furnish most of the

Jan 1, 1941

By Oren C. Baptist, Eliot J. White

Samples of four reservoir sands having different degrees of water sensitivity were subjected to several laboratory tests to determine differences in capillary behavior attributable to clay-mineral effects. The degree of water sensitivity was estimated by the difference between gas and water permeability. Unsaturated pore volumes determined with mercury injection were comparable to irreducible water saturations determined with the semipermeable bar-rier method only for the non-sensitive sands that contained small amounts of non-swelling clay minerals. Irreducible saturations were independent of salinity of the water, which suggests that most residual water is adsorbed 0.7 a film over solid surfaces and that internal retention by clay minerals is relatively insignificant. The water-sensitive sands imbibed water to higher saturations than did non-sensitive sands, and this result is believed to be a combination of the effects of clay minerals and preferential wettability; however, the relative importance of each of these effects is riot determinable. Thus it is concluded that the semipermeable barrier method is the best of the laborafory methods used for estimating formntion water .saturations in the sands studied. INTRODUCTION This investigation is a continuation of studies of the role of clay minerals in petroleum production in the Rocky Mountain area. Previous work has shown large differences in gas and water permeability in numerous reservoir sands; these water-sensitivity effects observed in the laboratory have been correlated with well behavior in the field, and the degree of water sensitivity imparted to reservoirs by the various clay minerals has been determined.'.' The effect of interstitial clay minerals on formation water3 saturations is not so well known. It has been reported that formation water saturations probably are higher in clayey than clean sands,' but this effect has not been evaluated in the laboratory, and the relative effect of the various types of clay minerals on formation water saturation has not been determined. The clay-mineral groups of most importance to this study and to petroleum production in general are kaolinite, illite, and montmorillonite. The minute layers of montmorillonite are loosely bound to one another so that water enters between them, causing great expansion of the particles. Kaolinite and illite do not exhibit interlayer hydration, but they do immobilize considerable amounts of water owing to their large surface areas, which are of the order of 15 to 97 m2/gm of clay.5 The four Wyoming sands used in this study were selected to represent a wide range of water sensitivities. These sands, with the number of wells and fields from which the samples were obtained, are: Second Frontier, five wells in two fields; Newcastle, six wells in one field; Tensleep, two wells in two fields; and Lower Muddy, five wells in one field. EXPERIMENTAL METHODS AND PROCEDURES Water-displacement data were obtained by the semipermeable barrier method," using both fresh water and brines having either 16,500 ppm sodium chloride or calcium chloride. A displacement pressure of 35 psi was found to be sufficient to obtain the practical irreducible water or brine saturation (IWS, IBS) in most samples. Mercury-injection data were ob-tained with equipment and pro-cedures similar to those described by Purcell.7 Exceedingly high pressures are required to attain complete mercury saturation by this method; however, since saturations in most samples change very little with large pressure increases above 1,000 psia, the maximum pressure used was 1,400 psia. To facilitate comparison of mercury-injection and water-displacement results, it is convenient to express mercury-injection data in terms of unsaturated pore volume. The abbreviation, (100 - SHg)min, is used to denote the pore volume unsaturated by mercury at 1,400 psia injection pressure. Gas permeabilities, ki, were deter-mined by the method proposed by Klinkenberg.8 Methods of determining types and amounts of clay minerals by X-ray diffraction analyses, as well as methods of determining water permeability, have been described previously.' The imbibition characteristics of

Jan 1, 1958

By T. H. Alden, H. W. Schadler

The strain rate dependence of the flow stress of the eutectoid Zn-Al alloy has been determined as a function of mechanical processing, microstructure, and temperature. The best superplastic properties result from the ultrafine, equiaxed structure produced by solution treatment and isothermal transformation at 0°C. Lamellar structures produced by isothermal transformation and coarse equiaxed structures produced by annealing also exhibit strain rate sensitivity in excess of 0.5, but at higher stresses and lower strain rates than the finest structure. Solution treatment and isothermal transformation eliminate the effect of prior processing history. Small composition variations in the binary alloy do not influence the mechanical properties. Below the eutectoid transformation temperature (.275C) increasing temperature lowers the flow stress at all strain rates. The data do not favor any of the present proposals for the mechanism of superplastic flow. ALLOYS of zinc and aluminum, near the eutectoid composition, have been investigated for: 1) the flow stress-strain rate and elongation behavior,1, 2) the transformation kinetics,3 and 3) structure,3"5 but the structure sensitivity of the mechanical properties is poorly understood. Using a near eutectoid alloy water-quenched from 380°C, Backofen et aL2 estab- high and increases with increasing strain rate. They found a correlation between strain rate sensitivity and tensile elongation as expected from the increased resistance to necking that a high strain rate sensitivity provides.296 The large elongation at high strain rates is attractive for metal forming. Since most other superplastic alloys7-l3 do not show high strain rate sensitivity at such a high strain rate (for the exception see Ref. 12) there is the possibility of a unique deformation mechanism for this alloy. The sensitivity of the mechanical properties of the eutectoid alloy to thermal history1 suggests a structure sensitivity that has not been demonstrated. Gar-wood and Hopkins3 identified a lamellar product for material transformed between 200" and 260°C. The size of the lamellae decreased with decreasing temperature. They also demonstrated that an unresolved transformation product formed below 200°C. A granular two-phase material was resolved for specimens quenched to below 150°C by Mitbauer and sauerwald4 who observed coarsening of the structure after annealing. The role of grain boundaries in superplastic deformation is suggested by the strong effect of grain refinement in encouraging this phenomenon at high strain rateS7-11, 13 and is emphasized in several proposals about rnechanism7, 8, 12 and in a theory14 of high-temperature deformation. Alden8 showed metallographic evidence that grain boundary sliding is occurring extensively at strain rates where m is large but less at high strain rates where normal plasticity is observed. Holt and Backofen10 have shown that sliding also oc-

Jan 1, 1969

By D. S. Harries, R. I. L. Guthrie

"The use and development of scientific disciplines involved in heat transfer technology, related in general to steel masses and in particular to batch annealing, is demonstrated.The measurable benefits of cooperation are tabled; on industry's side, this includes a 10 to 20 per cent decrease in annealing time, and a corresponding higher productivity potential. The returned benefits to the academic engineer include the development and refinement of new computer algorithms related to heat transfer mechanisms.IntroductionThe object of this discussion is not really to describe an improvement in the batch annealing operation, but to use the project as an example of joint work between industry and the academic field. Both parties have derived a number of substantial benefits. These benefits will be listed, of course, but the batch anneal project will be used just as a typical example of cooperation. Why it happened will be explained, what actually happened will be described and finally some thoughts about areas in the field of heat transfer, where cooperation will continue in the future, will be highlighted. The paper will close with a message.Industry OverviewAt the outset, perhaps it should be understood that, in general, the Research Department at Dofasco believes that the universities and their staff are not destined for the problem-solving role in industry. Its opinion is that the university staff is best suited to the gathering and dissemination of knowledge. There are other more professional problem solvers for industry, including the steel industries' own individual investigation groups. Dofasco, therefore, looks to its academics for consultation. It benefits by bouncing ideas off them, and through rubbing shoulders with them in such a way that their knowledge can be tapped, and thus establish more effective scientific routes. In addition, the younger and brighter engineer s can broaden their scope through the intellectual contact with experts. The university professors can, it is believed, benefit through closer contacts with result-orientated research. They can also develop an appreciation of the fiscal control necessary for industrial investigations, without government subsidies, grants, etc., and with massive overheads."

Jan 1, 1982

By J. Châteauneuf, R. Dupéré, D. Mrabet

"In gold processing plants, it is common to start gold cyanidation in the grinding circuit by simple cyanide addition or as a result of recycling residual cyanide. In such cases, advantages such as a decrease in gold lockup and reduced leach time have been noticed. The prevailing conditions in grinding circuits such as intense mixing, particle breakage and friction or high temperature are quite different from those found in tanks and so is the resulting cyanidation behaviour. To gain a better understanding of the cyanidation behaviour in mills and of the pertinence of cyanide addition in grinding circuits, lab tests were conducted using an industrial ore from Canadian Malartic mine. In this study, the effects of different parameters on cyanidation in grinding circuits were examined; parameters such as such as temperature, dissolved oxygen, cyanide concentration and pH. The results showed that the kinetic benefits of high temperature in the mill can overcome the low dissolved oxygen concentration thus leading to an overall gold dissolution kinetics improvement for temperatures up to 50°C. However, gold leach in the studied grinding circuit at lab scale caused an increase in cyanide consumption with a higher generation of iron cyanide and SCN-. These results were confirmed by tests in the Canadian Malartic plant where the cyanide addition was moved from the SAG mill to the leaching tanks resulting in a 20% savings in cyanide consumption.IntroductionCyanidation in grinding circuits can benefit gold processing by decreasing gold lockup and by reducing leach time. However, other aspects regarding gold and cyanicide dissolution come into play in the conditions prevailing in grinding circuits. Indeed, high turbulence, high temperature, recycling load, friction and particle breakage make cyanidation behaviour in grinding circuits different from in-tank cyanidation (Marsden and House, 2006). In several cases, cyanide in grinding is limited to a very low level or completely avoided such as in circuits with gravimetric separation, for ores requiring oxidative pretreatment or for preg-robbing ores. In other cases, water management imposes a certain recycling of residual cyanide. This problem is generally addressed by a case-by-case approach. However, the chemistry of cyanidation in mill circuits is worth investigating in order to assess the advantages and disadvantages."

Jan 1, 2016

By Hisaaki Takata, Nobukazu Nanko, Ichiro Izawa

INTRODUCTION Tochibora Mine belonged to Kamioka Mines, which are located in Gifu Prefecture, the cen- tral part of the Japanese main island, has occupied the important position as a main source of silver, lead and zinc for the smelter of Mitsui Mining & Smelting Co., Ltd.. The annual production of crude ore goes up to about 1 mil- lion metric tons with average grades of 20g/t Ag. 0.31% Pb, and 4.18% Zn. For the last 20 years, the mine has struggled with the depressed zinc metal price in yen and the escalation of operating cost, especially la- bour cost. For instance, prices of commodities and labour cost have been raised 8 times and 14 times respectively during this period. On the other hand, total operating cost has been con- trolled to increase 4.5 times. The productivity of the mine has been increased 4 times by means of improvement of individual works and adoption of perfectly mechanized trackless mining system to reform the mining method. Some improvements are presented as follows; Today, drifting is carried out by the tunnelling crew which consists of 9 operators equipped with 5 Mobile-Jumbos, 2 LHD's and a jeep for carrying and loading ex- plosives. In order to get the high utilization of these machines, each crew manages systematically and continuously adjacent 15 faces under the direction of a forceman. As a result, we have accomplished high advance of drift. Furthermore, raising is carried out by a set of the raise-borer in case of long raises like ore- passes and also by the stage blasting method in case of short ones like slot-cuts. Generally speaking, the sublevel stoping method is considered to be one of the best methods for various respects; high productivity, low cost, easy grade control and safety. This method has been introduced in Tochibora Mine since 1950 and is now widely applied to lodes that could not be mined before by this method be- cause of the shapes of them and the conditions of their country rock. Now we are convinced to be nearly accomplished for our method. This report presents some examples of the standard sublevel stoping method and its variations which are practised at the mine. STANDARD SUBLEVEL STOPING Up to 1979 since 1950 when this method was first applied at the mine, 17 million tons of crude ore have been produced by this method, which amounted to 55% of the total production of the mine. During three decades, the productivity has been increased considerably by means of trackless mining system using large-sized machines and etc.. In other words, mining efficiency has been increased from 20 tons/man.shift to 100 tons/man.shift at large stopes. Formerly undercutting was carried out above the drawing drift by jack-legs and small scrapers and then several cone-shaped glory holes were made by stopers between the undercut level and the draw level. But now, a undercut drift is driven in parallel with the haulage drift at the same level of it. And at the undercut drift, drilling upward is carried out by a large-sized machines like the fan drill in order to extract the broken ore directly at the drawing drift connected with the haulage drift. Simplification of the work as well as utilization of large- sized machines enables to get higher productivity. But if the deposit is comparatively wider and the broken ore around the middle part of the deposit cannot be extracted, several drawing drifts are driven to the deposit and in order to minimize dead ore at the final stage of operation, the

Jan 1, 1981

By David S. Bolin, Bruce Kennedy, Leigh A. Readdy, Graham Mathieson

INTRODUCTION The estimation of ore reserves is a process that begins with the earliest exploration stages on a property and continues throughout any subsequent evaluation and exploitation of the deposit. During exploration and preliminary evaluation, the results of these reserve estimates constitute the basic data for prefeasibility studies and economic analysis. The decision to continue exploration and development or to abandon a prospect is often based upon these studies. During the active life of a mine, reserve computations are continuously revised to assist in development planning, cost and efficiency analyses, quality control, and improvement of extraction and processing methods. Accurate reserve estimates are also required when financing a project, purchasing or selling a property, and for accounting purposes such as depletion and tax calculation. It is important to remember that the reliability of ore reserve estimates varies progressively through time as more and more information becomes available. The lowest order of reliability of estimation of reserves exists at the time of discovery. The maximum level of certainty concerning the ore reserves within a deposit is reached when the deposit is completely mined out. Between these two extremes are variable levels of certainty as to the tonnage and grade of the resource. This is particularly true of that portion of the mineral resource that constitutes the "minable reserve," as this portion is dependent upon economic as well as geological and technological factors. In the following discussion, several of the factors affecting ore reserve computation and some of the commonly used methods of calculation are presented. The first part of the discussion is confined to classical methods of hand calculation utilizing level maps and sections. The second part of the discussion presents an overview of somewhat more sophisticated methods of geostatistics which have been developed within recent Years. Geostatistical methods frequently provide the best ore re- serve estimates for many deposits. However, a digital computer is required for such geostatistically derived estimates due to the number and complexity of the cornputations involved. For many properties the classical nongeostatistical methods are adequate, particularly in the early exploration stages. In fact, it is the author's contention that even at those properties where the geostatistical approach is employed for reserve estimation, the geological and engineering staffs should prepare an estimate by traditional means. This provides an internal audit for the reserves and at the same time requires a continuing close appraisal of geologic problems that influence the presently known geostatistically estimated reserves and production at the mine.

Jan 1, 1982

By R. W. Shoenberger, J. D. Clendenin, W. L. McMorris, N. Schapiro, B. R. Kuchta, A. A. Terchick, R. J. Gray, J. G. Price

INTRODUCTION * The United States is fortunate in having enormous reserves of metallurgical-grade coals. Although these coals are better in quality and more accessible than most coals found throughout the rest of the world, the best grades of these coals are being depleted. Consequently, more efficient exploration tools and techniques, such as advanced methods of core drilling and logging, correlation by palynology,** stratigraphy, paleontology and petrography are being used to help assess the extent and quality of the remaining coal reserves. Exploration and assessment of new and existing coal properties become of utmost importance in determining (1) the economic justification for mining the coal, (2) the optimum design of the preparation plant and (3) the most effective use of the coal. Fortunately, the cost of mining coal has remained stable because of better mine planning, more efficient operations and increased mechanization of mining operations. However, increased mechanization raises the amount of impurities in the coal mined, and this requires more and better coal beneficiation to meet the more stringent quality requirements set by the market. Besides, mechanical miners also produce relatively fine coal and, to ensure maximum liberation of impurities, much of the coal presently being used must be crushed to a finer size prior to preparation. The bulk of all coals presently used in this country is mechanically cleaned, much of it at a lower specific gravity than in the past. This necessitates the use of new and improved processes and equipment for coal washing and recovery, such as heavy-medium cyclones and vessels, and froth flotation cells. However, because wet-cleaning processes are pre- dominant in the United States and fine coal retains large amounts of moisture, the increased production of cleaned fine coal accentuates the need for new or improved methods and equipment for dewatering and drying this coal. The larger amounts of coal being beneficiated and the use of new and improved beneficiation processes will aid in controlling and ultimately eliminating sources of pollution. Modem coal markets demand coals that meet rigid specifications. Most coals are purchased under contracts that specify moisture, ash, and sulfur contents, or heating value, depending upon the end use. There has also been a growing trend toward specifying other properties, including particle size and coking capability. These specifications may include not only the * Editor's note: Because of the numerous and varied contributions of the associate authors of this chapter, the text does not differentiate between sections prepared by each individual as has been done in other chapters. ** Palynology is the study of plant microfossils, especially spores, pollen, and other types of fossils not usually studied by paleontologists.

Jan 1, 1968

By Jaana Romppanen, Satu Jyrkönen, Tiina Ranki, Peter Björklund, Markku Lahtinen, Kaj Eklund, Päivi Suikkanen

Outotec is continuously developing our existing process equipment and new equipment solutions to enhance the Flash Smelting process. Thanks to the long operating history of the Outotec Flash Smelting process feedback from the numerous operating references are available and is utilized. The general goals for development work are to improve equipment performance, thus realizing savings in Smelter plant operation costs by increasing the process efficiency and online availability. Digitalization also opens new possibilities for the feeding equipment and furnace operation monitoring. These solutions will improve the safety and performance of the smelter, and provide process and equipment related information which has not been available earlier. INTRODUCTION The year 2019 marks the 70th anniversary of Flash Smelting. The technology was operated on industrial scale for the first time at the Outokumpu Harjavalta copper smelter in Finland in 1949. The Flash Smelting technology, is now owned and developed by Outotec Oyj and the first plant, is now owned by Boliden Harjavalta Oy. The two companies have been evolving throughout history by optimizing the process for various feeds and raw-materials, as well as through developing the equipment and operating practices. Even though sustainability was not a hot theme/topic during the first days of Flash Smelting, it has nevertheless been the key principle in guiding the development. This is well proven by the wide adoption of Flash Smelting for the processing of copper and nickel concentrates, mostly due to its ability to fulfil the economic and resource efficiency criteria demanded by its operators. Along with the process technology development, also development of the equipment has taken place over time. Outotec is continuously working on developing our equipment to better suit the changing need of our customers in the continuously changing operational environment. Orebodies are getting more challenging with lower ore grades and more impurities. Achieving high recoveries for all valuable elements becomes more difficult with high slag quantities and with the need to tackle the high impurity concentrations. There is a need for higher capacities in greenfield and brownfield smelters. The role of the Loss-in-Weight Feeder, the Air Slide and Concentrate Burner is to ensure even feed into the reaction shaft of the Flash Smelting Furnace, and to enable controlling the process well, thereby enabling the best performance for the customers smelter. The design of the Flash Smelting Furnace aims for high availability, long campaign and safe operation.

Jan 1, 2019

By M. K. Yen, W. R. Hibbard

Previous studies of plastic deformation of metals have emphasized the important role of bending and constraints during strain under relatively pure stresses.1"5 Some new phenomena such as early conjugate slip6 and polygonization7 are intimately concerned with the relief of bending stresses, the former by slip and the latter by a process analogous to re-crystallization. However, few analyses of the bending deformation of single crystals were found in the literature, and those8,9 are sufficiently previous to the modern interpretations of slip to invite further investigation in this area. The transverse bending mode of testing, using the two-point loading method, was selected because the center portion of the specimen may be considered as under a theoretically pure bending stress with a uniform bending moment. Considerable attention was given to both the lattice distortion and flow characteristics of the crystals during deformation. Experimental Proeedare A specimen under the action of equal and opposite couples at both ends is said to undergo pure bending. The shear and moment diagrams of a specimen under the two-point loading method of transverse bending are shown in Fig 1. The moment over the middle-third of the span is equal to PL/6, and the vertical shear is zero. Fig 2 (A) illustrates the stress distribution in the elastic range on a plane across the middle of the specimen. It can be seen that the normal stress has a maximum value at the extreme surfaces on the tension and compression sides, and decreases proportionately to zero as it approaches the neutral plane. However, when the plastic range is reached, the stress distribution is no longer a straight line relation, but changes in a manner which can be best illustrated as shown in Fig 2(B). The following calculation and stress analysis are mainly in accordance with the works reported by Timoshenkol0 and Kochendörfer.9 From the simple beam formula, the maximum normal stress will occur at the surface of the specimen. For a round specimen with a radius r and for a rectangular specimen with a height 2h and width 2b, the maximum normal stress, Sp, will be given by the following formulas: For round specimen: 2PL Sp = 3pr3 [1] For rectangular specimen: Sn = 8bh2 [2] Since it is reasonable to consider that slip takes place under the same conditions as in uniaxial loading, the resolved shear stress S?, along the operative slip direction will be as follows: For round specimen: 2PL sin x cos ? Sp = 3pr3 sin x cos ? [3] For rectangular specimen: PL S8 = 8bh2 sin x cos ? [4] where X is the angle between the specimen axis and the slip direction and X, the angle between the specimen axis and the major axis of the glide ellipse. It was also reported by Kochenclorfer9 that the critical bending moment, that is, the bending moment exerted on the specimen to initiate slip, should be higher than the value given by the equations stated above. Based

Jan 1, 1950

By Smith F. A, Both R. A

The application of biogeochemical methods in mineral exploration in the semi-arid to and environment of Western Australia was investiga- ted in an area near Norseman. The reliability of these methods was evaluated by comparing trace element characteristics of rock, soil and plants in the vicinity of the Pioneer BB pros- pect. The prospect is located in the south- western part of the Pioneer Dome, where granite gneiss core is surrounded by a 'greenstone' sequence of ultrabasic, basic and sedimentary rocks. Nickel-iron sulphide mineralization occurs discontinuously along one of the basic- ultrabasic contacts. Analyses of unweathered and partly weath- ered rock from diamond drill cores show the ultrabasic rock to be highly variable with re- spect to nickel, copper, cobalt, zinc and manga- nese. Samples of weathered bedrock and over- lying soil were analysed both for total trace element contents and for the trace elements associated with secondary iron and manganese oxides. Approximately 30 per cent of the total nickel content of the weathered basic rock is associated with secondary iron and manganese oxides, compared to approximately 15 per cent in the weathered ultrabasic rock. The soil is partly transported but has a residual component sufficient to provide a reli- able indication of the underlying rock chemistry, although the trace element content of the soil is less variable than that of the rock. Total

Jan 1, 1973

By George S. Rice

"The emission of hydrocarbon gases from coal beds and contiguous strata causes many accidents in coal—mine workings, the number of fatalities so caused being second only to those due to falls of roof. Gases tend to increase in amount with depth of coal mining, hence the danger of explosion is increased with depth. The pressure of the gas in virgin—coal areas at a distance from mine workings likewise tends to increase with depth from the surface, probably due to corresponding increase in hydraulic head and possibly, when the gas is held in nonporous formations, to greater ground pressure. The rise in gas pressure with depth under usual conditions is shown in wells drilled from the surface and in some coal fields in drill holes into the face of workings; however, under normal conditions of coal formation gas does not issue into workings under high pressure because the coal and adjacent strata have many bedding and joint planes which allow the gas to escape freely at the face of the workings. The rare occurrence of instantaneous outbursts of gas, with violent effects referred to later, constitute the exception.Variations of volume and pressure of fire-damp or methane found in different coal beds by wells at a distance from mine workings, are analogous to variations in volume and pressure of natural gas found in different gas and oil sands, although in general the pressure tends to increase with the depth. Sometimes, however, in tight sands higher in the formation the pressure of gas therein is abnormally high, and on drilling the well deeper gas in the lower strata may be found at lower pressure."

Jun 1, 1934

By L. R. Duncan, O. M. Wicken

Magnesium, the eighth most abundant element in the earth's crust, is found widely distributed in a variety of minerals. Among the more commercially important ones are magnesite (MgCO,), brucite (Mg[OH],) , dolomite (CaMg[CO,],), and the salts magnesium sulfate and chloride often found in natural brines. Among other commercially important magnesium-containing minerals are olivine ([MgFe],- SiO,) , talc (H,Mg,[SiO,],) , and serpentine (H,Mg,Si,O,) . These are valuable because of desirable characteristics given them by the magnesium content and its placement in the particular crystal structure. These minerals are the raw materials for a host of products including magnesium metal and several grades of magnesia or magnesia- containing materials for refractories, fluxes, fillers, insulation, cements, decolorants, fertilizers, and chemicals. Considering only those minerals valued for their magnesia or magnesium content, over 85% of the material tonnages are processed to be used as refractories. Dolomite, which is used in enormous tonnages for its physical properties in construction, has an important use as a refractory raw material in its own right and, after calcination, as a precipitant for magnesium hydroxide, which is an intermediate for the production of magnesia or magnesium metal. Magnesia from the reaction of calcined dolomite (or limestone) with sea-water or magnesium-containing brines has supplanted much of the production of magnesia from mined magnesite, particularly in the United States. The best known of the minerals directly and widely exploited for magnesia content is magnesite, one of the calcite group of rhombo- hedral carbonates which includes calcite (Ca- CO,) , siderite (FeCO,) , and rhodocrosite (MnCO,) among others. The members of this group enter into a wide range of substitutional solid solutions when the positive ions have similar radii. The radii of magnesium and iron ions are within 6% of each other; hence, magnesite and siderite form a complete series of which breunnerite (ferroan magnesite) is a well-known end member. However, the radius of calcium ion is 36% larger than that of magnesium ion, and only limited substitution exists at each end of the MgC0,-Cam, series. Dolomite is not a member of the calcite group, but results when calcium and magnesium ions alternate in equal number in an ordered structure among carbonate ions. The result of these relationships is that calcite and dolomite, often found intermixed with magnesite, occur commonly as identifiable crystal entities which can often be separated to a varying degree from the magnesite by various beneficiation techniques. Magnesite, when pure, contains 47.8% MgO and 52.2% CO,. The pure mineral is sometimes, but rarely, found as transparent crystals resembling calcite, but, preponderantly, magnesite contains variable amounts of the carbonates, oxides, and silicates of iron, calcium, manganese, and aluminum. Magnesite may be either crystalline or "amorphous" (cryptocrystalline). The crystalline form has a hardness of 3.5 to 4.0. The color may range from white to black with shades of yellqw, blue, red, or gray. The color is not a fundamentally significant indicator of purity, but in a given deposit, an experienced person can often roughly grade magnesite by assessing color and crystallinity. The crystalline form of magnesite occurs in

Jan 1, 1975

By Robert Wamsley, W. E. Jones

One of the earliest problems in the life of any community is the provision of an adequate supply of water sufficiently free from all types of contamination to be suitable for domestic purposes. Generally speaking, the location of most communities is determined to a great extent by the availability of an adequate supply of satisfactory water. For a mining camp, that consideration cannot be foremost. Here, the ore takes first place, and the men who mine it must do the best they can under the existing conditions. If there is no local source of water, it must be brought from some distant source or must be found by sinking shafts or drilling wells. Fortunate indeed is the mining company that discovers a commercially valuable ore deposit beside a never failing creek full of pure water, with sufficient water rights available. because the acquisition of water in any other manner nearly always involves not only a considerable period of time but the expenditure of considerable money. The experience of Climax Molybdenum Co. demonstrates the measures that sometimes are necessary in order to provide a suitable supply of water. The Climax mine and mill are on the Continental Divide! about 13 miles northeast of Leadville. The elevation of the domestic part of the camp varies from a minimum of 11,320 ft. to a maximum of approximately 11,550 ft. above sea level, and, as is common at such altitudes, the near-by streams that might be suitable for a water supply are small and intermittent, usually flowing only during the summer months. The only streams of any size in the immediate vicinity of Climax are the Ten Mile and Arkansas Rivers The headwaters of Ten Mile River are on the Company's property, and its water has been used for the domestic supply. The headwaters of the Arkansas River are about 2 miles distant and have not been used as a source of supply by the company. During the past 11 years of the production of molybdenum at Climax, the number of families living there has increased from about 45 to 283, and the population has increased from about 200 to 1200 persons. Consequently, the capacity of the water-treatment facilities, and the amount of water available, had to be increased to meet the requirements of the camp. As early as 1932 it was recognized that the water in Ten Mile River would not continue to be adequate for domestic purposes and after considerable discussion it was decided to drive a drift through the major fault in an effort to find additional water. This drift was completed in 1935 and tapped sufficient water to make the supply adequate. This water was treated in a tank underground, where lime was added, and was then piped into the domestic supply lines. At about the time this line was completed, the presence of fluorine in harmful concentrations was discovered in the water. This problem was submitted to the International Filter Co. and in November 1937 a plant of its design was put in operation for treating the water to remove the fluorine. This plant proved entirely successful,

Jan 1, 1946

By Peter Keppler, Charles Jackson

WHY DO AN AUDIT? There is increased enforcement of environmental laws and regulations at State and Federal levels with attendant steep fines and even the possibility of jail sentences. We are all aware of environmental and public health and safety incidences (i.e., Love Canal, Bhopal) which have led to stringent laws and regulations (i.e., CERCLA, RCRA, SARA). In some cases, the courts have specified that a company institute an audit program as a condition of settlement of claims which related to lack of environmental control. The U.S.EPA issued an Environmental Auditing Policy Statement in the November 8, 1985 Federal Register (pp. 46504-46508) which encourages the use of environmental auditing by regulated entities. Elements of what EPA considers to be an effective environmental auditing program are outlined and briefly explained. These factors combine to indicate why there is a growing number of companies which have instituted an audit program. Briefly, the program can and should be used to monitor compliance with environmental regulations and corporate policy, to prevent violations, to improve policies and procedures, to raise the level of environmental awareness, to encourage communication among operations and all management levels about environmental problems, and to measure risks and control costs. AMAX Inc. has had an environmental audit program since the early 1970's. The AMAX Environmental Affairs Department, working with the Law Department, oversees and coordinates environmental audits and analyzes the findings which an audit reveals. Facilities are audited on a regular schedule; those having the greatest potential for environmental liabilities are audited at least annually; other facilities are audited less frequently. The question of who performs the AMAX audits was settled in favor of the audit team being independent of personnel from the facility being surveyed. Other methods of auditing could be the following: - Independent contractor (Appendix A) - Combination of independent contractor and in-house staff - Self-audit by site personnel The merits and demerits of who should conduct the audit can be analyzed to suit your particular needs. Next you need to decide on the procedure for the audit and the form for reporting and follow up. Environmental publications referenced in Appendix B can be helpful to you at this point. After deciding on the form of auditing, a schedule is prepared and followed to the closest extent possible. This schedule should be published and distributed to the sites so facilities know when they are being audited. This is not designed to be "a game of hide and seek." Various elements of the AMAX Audit Program are as follows: Team selection Pre-visit preparation Site visit Exit interview Report Using the audit Follow-up Team Selection The usual make-up of the team is the audit manager, the environmental specialist who normally provides assistance to the site or has knowledge about the operation, and a legal representative if his or her schedule allows. The legal representative will review the findings of the audit team if a personal visit is not timely or necessary. Size of the team can be expanded, but a minimum of the audit manager and the environmental specialist is best. Two sets of observations are better than one. The environmental specialist can also provide the rapport which is beneficial to creating the appropriate tone so that the site people will be as cooperative as possible. This is not to be an antagonistic exercise.

Jan 1, 1991

By Peter A. Allen

INTRODUCTION Lac Minerals Ltd., a significant North American producer of gold and other metals for over three decades, recently completed the financing for its third discovery in an eight year period. From 1975 to 1982, three important gold deposits in Quebec and Ontario: namely Bousquet, Doyon and Hemlo, were located and tested by company geologists. When current development plans are complete, Lac will have injected $400 million into these deposits. A discussion of these projects and their financing reveals some extraordinary challenges faced by top mining management. Responses to these challenges developed by Lac management may interest executives planning to proceed with new North American gold or base metal mines. MINE DE BOUSQUET In 1976, we explored a property containing a large low grade surface gold deposit. The geologial setting was exciting and we tested recent rethinking about the volcanigenic genesis of gold and base metal occurrences. These ideas helped pus to persist in drilling a nearby conductor and 600,000 ton, 0.22 ounce/ton orebody was outlined. With gold at $Cdn.150 per ounce the feasibility was approved and work started February 1978. Availability of a company custom mill 35 miles away reduced our immediate capital needs to $8.5 million. First of all, understanding the geological significance of results at Bousquet was critical. Mine and surface exploration geologists at Lac are continually and closely working together to better understand the nature of gold deposits in the Shield. This management emphasis on both pure and mine geology meant that a much larger ore reserve could confidently be predicted. (A proposal to quickly develop and ship the ore to a nearby company mine was discarded.) Instead of designing just for the initial plan of 500 tons per day we therefore included headframe, shaft and hoisting capacity for 1,700 tons and provided a compartment for future shaft deepening. These prebuilt additions were welcomed within two years. The type of collaboration whereby surface and mine geologists make study and field projects of each other's problems sets the foundation for this predictive ability. At Lac, the traditional responsibility for and supervision of the mine geologist by the mine manager is modified by this collaboration. This adds interest and scope to the geologist's work and lets him think beyond production requirements. Besides such management considerations, dedicated, professional geologists with integrity and lots of practical experience are needed to plan successful developments like Bousquet. Second, projecting future bullion revenue was critical and our experience selling production for future delivery gave us a way to ensure that loan repayment at term would not be jeopardized by falling metal prices. Output from a single mine is often reduced or curtailed for numerous reasons, so "selling forward" is done best and with least risk by companies like Lac with more than one or two producing locations for that metal. At first, a forward marketing program was considered unwise, speculative and unorthodox by analysts and other producers. Declining markets in the early 1980s prolonged gold project capital recoveries however, and critics were better able to appreciate the usefulness of such a tool. The notion that gold miners shouldn't sell forward is rooted in the belief that long-run gold prices will rise as modern social theory implementation in democracies inevitably erodes currency values. Selling against this trend goes against this industry belief or "ethic" and is at odds with the company shareholder who expects the gold price to rise not fall. Nonetheless, an efficient tool is available to the gold producer (not to most other metal producers) to quickly disengage from adverse price trends or to lock in spot prices instantaneously for two years or more of profits. Gold had recently retreated from U.S.$200 to $104 and now had reversed to $150. Lac had been forced to close several of its producers during the late 1960s because central bank-controlled

Jan 1, 1985

The Bureau of Mines studied blast-produced ground vibration from surface mining to assess its damage and annoyance potential, and to determine safe levels and appropriate measurement techniques. Direct measurements were made of ground-vibration-produced structure responses and damage in 76 homes for 219 production blasts. These results were combined with damage data from nine other blasting studies, including the three analyzed previously for Bureau of Mines Bulletin 656. Save levels of ground vibration from blasting range from 0.5 to 2.0 in/sec peak particle velocity for residential-type structures. The damage threshold values are functions of the frequencies of the vibration transmitted into the residences and the types of construction. Particularly serious are the low-frequency vibrations that exist in soft foundation materials and/or result from long blast-to-residence distances. These vibrations produce not only structure resonances (4 to 12 Hz for whole structures and 10 to 25 Hz for mid walls) but also excessive levels of displacement and strain. Threshold damage was defined as the occurrence of cosmetic damage; that is, the most superficial interior cracking of the type that develops in all homes independent of blasting. Homes with plastered interior walls are more susceptible to blast-produced cracking then modern gypsum wallboard; the latter are adequately protected by a minimum particle velocity of approximately 0.75 in/ sec for frequencies below 40 Hz. Structure response amplification factors were measured; typical values were 1.5 for structures as a whole (racking) and 4 for midwalls, at their respective resonance frequencies. For blast vibrations above 40 Hz, all amplification factors for frame residential structures were less than unity. The human response and annoyance problem from ground vibration is aggravated by wall rattling, secondary noises, and the presence of airblast. Approximately 5 to 10 pct of the neighbors will judge peak particle velocity levels of 0.5 to 0.75 in/sec as "less than acceptable" (i.e., unacceptable) based on direct reactions to the vibration. Even lower levels cause psychological response problems, and thus social, economic, and public relations factors become critical for continued blasting.

Jan 1, 1980

By Charles H. Shamel

I fear most of the Institute members are already weary of the perennial controversy about the apex law. I feel that way about it myself now, though I have been guilty of considerable contribution- to the discussion in the past. The discussion does not seem to perceptibly influence previously held views and I would not again break into print on the subject but for the urgent invitation of the Chairman of our Law Committee. This energetic and able member has firmly determined to secure a revision of the mining law and among other things to eliminate the so-called apex provision from the U. S. mining statutes. He is, however, fair about it and has invited me to make ((the strongest possible argument in its favor." I am suspicious that he is acting on the psychological principle that it is usually easier to convince an audience against a cause vigorously but unsuccessfully defended than against one wholly mute. Nevertheless, I realize that personally he wishes me no harm, much as he hates the apex law, and so am willing that the Institute have whatever benefit may accrue from my taking up again the unpopular side of the discussion. I say this because the attitude of a large part of our "articulate" membership seems irreconcilably hostile; their minds are made up; favorable consideration is foreclosed; and they become impatient and even sarcastic at any attempt to elucidate a favorable view of the apex law. The exact question for discussion at the present time is not whether on abstract, or any other considerations, the apex law is the best possible rule, but the very different proposition whether, after nearly 50 years of statutory life and much longer as a practically universal miners' custom, it is now just and expedient to repeal the apex law. At this point it seems to me that we may profitably devote a paragraph or two to the subject of the origin of law in general, as we are presumed to be considering the subject from the high viewpoint of the general welfare of the nation. The most comprehensive and accurate definition of law in the legal sense is, that it is the body of rules for the regulation of human conduct which is enforced by the State, that is, by the nation.l Legal

Jan 1, 1915

By L. R. Mabson, F. M. Russell

INRODUCTION Roan Consolidated Mines Limited (RCM) operates five underground mines - Mufulira, Luanshya, Baluba, Chambeshi and Chibuluma (figure 1) . Associated metallurgical plants provide for the operations of milling, smelting two refineries for copper and a cobalt plant. Primarily a producer of high quality copper (242,000 tonnes during 1980) the Company is also the world's second largest producer of cobalt metal. RCM's remaining ore reserves at 31st March 1980 were 275 million tonnes at 2.84% copper. Monthly ore production is in excess of 1.2 million tonnes. Sublevel open stoping was the choice of mining method for the first underground operations on the Copperbelt for ore with dips steeper than 30 degrees. This was for use at the Roan Antelope mine, subsequently to be called Luanshya mine. The sublevel open stoping system was planned based on the methods used in many of the iron mines of Michigan and New York and in the copper mines of Tennessee. Peterson (Ref. 1) gave the following reasons for employing sublevel stoping, reasons which are still valid today: (1) the working place could always be barred and made safe, and the sublevel exit was always at hand; (2) the working conditions were similar day by day and drilling operations were repetitive; (3) pillar spacing can be varied as conditions demand; and (4) stoping operations could be shut down completely or opened up to full capacity at short notice, without affecting grade or causing wastage of reserves. Such was the success of the method that it was adopted as the basic mining method at all the RCM mines in their initial stages. Although cut and fill, block caving, and sub- level caving methods have been used, sublevel open stoping in its many variants still accounts for nearly 90% of total ore production in the Company. The following descriptions outline some of the applications of sublevel open stoping within RCM. LUANSHYA Geology There are two main ore deposits at Luanshya: the Roan (Luanshya Mining Area), in which mining began in 1930, and Baluba, in which mining production started in 1973 (figure 2). Both orebodies occur in synclinal and variably folded basins. These basins are underlain and completely surrounded by much older schists and granites. The ore formation, an argillite, lies near the base of the sediments and is underlain by conglomerates, quartzites and arkoses. Copper mineralisation is mainly found in two well defined zones, separated by a varying thickness of pyrite mineralisation. In the eastern part of the Roan deposit only the upper orebody is present, but west of 18 shaft and at Baluba the lower orebody predominates. Locally the subjacent quartzites of the footwall formation are also mineralised with copper. The copper mineralisation is found princi- pally as disseminated sulphides, mainly chalcocite, bornite and chalcopyrite. Near the surface the sulphides have been changed to oxides. At Baluba the cobalt mineral carrollite is found with the sulphides. Mining methods Sublevel open stoping is the basic mining method. In its standard form this method is best suited to steeply inclined orebodies, with simple structures and with a strong foot- wall and hangingwall. In recent years, as more complex folding and flatter dipping orebodies have been encountered, considerable variations have been introduced. Stope drilling is effected with drifters and extension steel.

Jan 1, 1981

By Vasily P. Muravjev, Gennady I. Razgildeev

The theory of reliability is a powerful mathematical tool for determining optimum selection of components and application of electrical power to coal mines. In order to make this tool useful, statistical material on equipment life must be gathered and all failures carefully recorded. Statistical data can be applied to new apparatus design and can be used to determine optimum configuration of network and maintenance to reduce costs. Reference is made to underground power systems in the USSR. Technical progress in the last few years has occurred in the design and application of highly productive coal mining and transporting machinery. One of the most important problems facing mining engineers is to increase the availability of the machine to obtain higher productivity. However, machine failures and breakdowns of electrical power supply components cause serious delays in the coal-winning processes. In spite of the fact that electrical equipment and the power supply contribute only a small percentage of direct mine costs, electrical failures as well as power supply delays can result in severe indirect losses. It is necessary, therefore, to consider reliability and safety in the application of electrical equipment underground. To obtain the best results, it is necessary to investigate and evaluate the reliability of the electrical mining components (starters, breakers, motors, cables, etc.) and optimal methods for minimizing maintenance, the desired result being equipment which is efficient and safe. Electrical equipment reliability directly influences economics: the lower the reliability the more frequently failures occur, causing serious working delays and possibly huge economic losses. By the same token, while increasing the number of preventive maintenance calls per unit time might result in fewer failures, thus reducing delays, the cost of making more frequent maintenance inspections will increase; this is one aspect to be discussed in detail. Obviously, failures of identical types of electrical equipment (starters with the same current and voltage, etc.) are influenced variably by different working conditions, environments, quality of the apparatus, maintenance procedures (personnel, frequency, quality), load, and other factors. Hence, the lifetime of identical types of equipment will vary depending upon usage in terms of the foregoing factors. Thus for a given type of electrical component, these factors must be considered quantitatively; the interaction of all these factors are evaluated quantitatively by a statistical method using probability theory. Equipment reliability must be quantitatively determined from a study of equipment life, since no one laboratory test can reproduce all working conditions and environmental effects. Nevertheless, reliability theory applied to electrical mining equipment is a very powerful mathematical tool for selecting as well as evaluating certain parameters. It is necessary to select several reliability parameters so that one can obtain an expression for the total overall economic situation in terms of cost, taking into consideration damage caused by electrical equipment failure and cost of maintenance. To accomplish this result, such characteristics as apparatus lifetime, breakdown idle time, and losses (damages) can be determined quantitatively on a statistical basis. For identical electrical equipment working under similar conditions, the previously mentioned reliability factors are random variables and therefore can be characterized readily by a probability density function. Investigations carried out by the authors in the Kuznetsk Basin (Kuzbas) in West Siberia, USSR, show that the reliability factors of electrical mining equipment are well described by the exponential, normal, or Erlang's distribution in most cases. Mining electrical equipment life is well-described by the exponential law. The distribution of lifetime density is

Jan 1, 1971