Search Documents

Jan 1, 1924

By AIME AIME

TWO weeks ago the writer was lunching in the Engineers` Club in New York with a man who has perhaps the widest acquaintance among engineers of anyone in the country a member of another of the Founder engineering societies. "By the way," lie asked. "who have they nominated for your next president."' "Doctor Becket," I told him- "Oh. that's line," he replied, in a heartfelt tone that rang with sincerity. "I have come in contact with him occasionally and he is just the right type.' And that is the way Dr. Frederick M. Becket impresses everybody. The right type. Most Institute members of the western group of hard-rock minors do not know him, but then they meet him in his swing around the circle next year they will not require a long acquaintance to sense his kindly and outstanding personality, to realize that he is a gentleman in the bet meaning o1 that word, a man of wide sympathies and interests.

Jan 1, 1932

By David K. Hylbert

This study was designed to investigate roof falls in room-and-pillar drift coal mines and to determine geologic methods for predicting unstable roof conditions. The study area was located in Harlan County, Kentucky and the Bailey Creek (Harlan coal bed) and Highsplint (Darby coal bed) mines were selected for study. Correlations were made laterally between surface outcrops and within the mines using lithologic and trend analysis criteria. Lithologic criteria compared cyclic changes in roof strata. Results indicated that roof falls are associated with zones of weakness within or between five vertical cycles recognized. Abrupt lateral facies changes occur. In the Highsplint mine the roof was classified in four categories or conditions using 98 rib sections for control. Structure contour and isopach maps were used to project axial trends of the sandstone roof. A roof-fall zone was examined using ten NX cores taken from the roof and included lithologic, petrographic and clay mineral studies. At the Bailey Creek mine roof failure was caused by the heading direction being driven subparallel to paleochannel directions. Computer programs were used in trend analysis studies. Cross-bedding, paleo-channel trough axis and sole mark studies indicated a 350 discrepancy between surface and in-mine trough axes at Highsplint. A direct relationship between joint and "slip" frequency and direction with sandstone roll trends was found. Surface joints compared well with drainage Segments, hilt did not correlate with roof falls in areas of mines under overburden in excess of 600 feet.

Jan 1, 1977

By J. G. Peacey

"Canada has a special place in non-ferrous pyrometallurgy because it is the only country in the western world that is a significant producer of all the major non-ferrous metals; aluminum, copper, lead, magnesium, nickel and zinc. This large non-ferrous pyrometallurgy industry has developed because of Canada's abundant mineral wealth and energy resources. Table I summarizes the number of primary non-ferrous production facilities in Canada and their share of western world production.Production of non-ferrous metals is a mature, capital intensive business and its basic processes have been in use for many years. Nevertheless, these processes have continued to evolve in response to changing needs and external pressures; such as the energy crisis of the early seventies; historically low metal prices in the early eighties and the continuing pressure to reduce plant emissions and improve in-plant working conditions. Canada's major metallurgical companies: Alcan, Cominco, Falconbridge, Inco and Noranda have played a leading role in pioneering new process technology and continue to meet the difficult challenge of keeping their operations competitive in the global metals market. This paper will try to give an overview of the major developments in non-ferrous pyrometallurgy, largely from the Noranda and Canadian perspectives, highlighting the current status of process technology and possible future directions.AluminumCanada has the world's second largest aluminum smelting industry and its capacity has expanded rapidly in recent years with the completion of several large projects in Quebec. The location and capacity of the Canadian aluminum smelters are given in Table 2. All these plants use the Hall-Heroult process, that was invented over a century ago but over the last twenty years considerable improvements have been made to increase productivity, reduce power requirements and emissions.The developments in aluminum cell technology can be illustrated by the experience at Noranda Aluminum. In 1971, Noranda Aluminum started its first pot line using Kaiser's P69 prebake cell, which was considered, at that time, the best available technology. The P69 cell was designed primarily for high productivity, operating at 150 000 amps and high current density to produce just over tonne Al per cell-day. The P69 cell is a simple design, typically operating at about 88070 current efficiency and 15 800 kWh/tonne Al. When Noranda Aluminum decided to expand in 1980, the Alcoa 697 cell was selected as it then represented the most proven, stateof- the-art technology. This cell is similar to that installed at Alcan's new Grande Baie and Laterriere smelters and is designed to operate at 180000 amps and 93070 current efficiency, producing about 25070 more aluminum per pot-day than the P69 cell using about 15070 less power. The 697 cell has a much more sophisticated cell design, with very good balancing of the magnetic field giving a flat metal pad and allowing efficient operation at the higher amperage. Alumina is fed via point feeders that provide an almost continuous feed allowing close control of the alumina level in the bath and the use of low-ratio bath composition, giving much higher current efficiencies."

Jan 1, 1991

By Allan F. Smith

The influence of hydraulic fluids on spontaneous heating in bituminous coals is determined by measurement of the temperature increases produced in coal-fluid mixtures heated to a temperature sufficient for the initiation of self-heating. Similar tests on as-received coal samples and water-coal mixtures are compared with the results obtained for the various hydraulic fluids. Three of the four coals were sampled from coalbeds known to have a history of spontaneous heating. The data provide a basis for predicting the possible effects in gob or carbonaceous refuse of coal mines.

Jan 1, 1963

By W. L. Barry

A review of the practices of analyzing for precious metals at the Reno Research Center, U.S. Bureau of mines, is presented. A general description of fire assaying, the physical layout of a fire assay laboratory, and the use of fire assaying in combination with atomic absorption, induction coupled plasma, and emission spectroscopy is reviewed. The combination of techniques significantly decreases the detection limits for precious metal analyses and simplifies the analysis of the platinum-group metals. Methods of protecting personnel from ingestion of lead are also discussed.

Jan 1, 1982

By D. R. Barker

The economic performance and competitiveness of a concentrator are dependent on the production of accurate real-time assay information and the manner in which it is utilized. Our paper describes the relative merits of on-and in-stream analysis techniques and the economic significance of Assay-Based control and Target Oriented Display Systems. At Outokumpu's pyhasalmi Concentrator, a Flotation Expert Display System aids the process operator to make better decisions and provides guidance on the most efficient method of achieving the desired control objectives.

Jan 1, 1989

By Victor F. Hollister

Although none of the deposits discovered to date are of commercial interest, significant Frasch or sedimentary sulphur deposits occur in Nova Scotia in Upper Mississippian Windsor Group evaporites. The evaporite sequence contains anyhdrite and is overlain by impervious shales. It also is •mderlain by locally petrolijerous formations that are potential hydrocarbon sources for reaction with anhydrite to produce sulphur. As well, stratigraphic and structural traps are known to exist in the Mississippian beds. Thus, all requisites for sedimentary sulphur genesis are present. Available hydrocarbon sources are numerous but small; resultant sulphur deposits therefore are probably also small. Evidence suggests, however, that sulphur deposition is not yet complete.

Jan 1, 1984

By M. S. NORTH

IT may be a far cry from the days of the old horse whim, and it is relatively a long way back to hand production in factories. Modern machinery has made possible deep shaft-sinking, newer methods have increased the recovery of mineral. Technically, excavating and ore dressing have advanced as has mass production and its many ramifications in the manufacture of commercial product. To those of the mining industry who would have us believe that mining and manufacturing are totally different enterprises, it can be said that certain differences do exist. These differences rather than being fundamental are the result of adhering to past practices which were possibly sound years ago but do not measure up today. Differences in managerial control, sales, and distribution, cost finding, etc., are often so pronounced that efforts to compare or contrast are almost futile.

Jan 1, 1930

By H. A. Kendall, W. C. Goins

Several investigations in recent years have shown that drilling rates are increased significantly with increased hydraulic horsepower. But, there has been no over-all method of designing jet-bit programs that efficiently uses the surface power. A study of present practices indicates that frequently as little as 50 per cent of the possible effects at the bit are used. Some observers have indicated that the best utilization of hydraulic horsepower (maximum effect on drilling rate) occurs when the bit hydraulic horsepower is maximum; others have stated that jet impact force is more important, and others have believed that maximum jet velocity is required. Limited efforts to date have shown some optimum conditions for bit hydraulic horsepower and impact, but these conditions cannot exist during drilling of a large part of the hole and do not provide a basis for designing a complete jet-bit program. This paper shows the maximum obtainable bit horsepower, impact force and jet velocity at all depths, taking into account the limitations of the pump, piping, hole and minimum circulating rate for adequate cuttings removal. Ranges of operation are developed; and flow rates, surface pressure and bit pressures are specified for each range to provide a maximum of any one of the desired effects. It also is shown that, by proper selection of nozzle sizes and by following the rules presented, the maximum obtainable quantities can be effectively utilized from surface to total depth. Finally, a simple graphical method of selecting nozzle sizes and flow rates is presented which can be used with familiar bit-company hydraulic tables and calculators to design jet-bit programs for maximum bit hydraulic horsepower, impact or jet velocity, as desired. These programs make most effective use of the pumps. Heretofore, there was no method available for designing field tests which adequately separated the effects of bit horsepower, impact and jet velocity. The programs and procedures developed in the paper are dissimilar and, when used in future field testing, should demonstrate which program is the most important in obtaining the fastest drilling rate. INTRODUCTION During the past decade, rig hydraulics has come into increasing prominence. There has been a definite trend toward providing higher horsepower pumps, jet-type bits have had increased use, numerous investigators"" have reported increased drilling rates as a result of increased hydraulics, and bit manufacturers have provided tablesa-" and calculators that are now commonly used 10 design jet-bit programs. Opinion has varied as to the hydraulic quantity which has the great- est effect on drilling rate. Papers and data have been presented that show pump horsepower,'9 it hydraulic horsepower and jet impact force,' each to be the most significant factor affecting drilling rate. Examinatibn of jet-bit programs of the bit companies indicates emphasis on jet velocity. Only pump horsepower can be eliminated because it can be used to produce any one of the bit effects which, a priori, must be more relevant factors. This contradictory state of opinion and practice regarding the bit effects is unfortunate, but several published references have been concerned with making one or another of the factors maximum; and, because these in each case have given results applicable to only intervals of the hole drilled, there seems to be ample reason to complete the previous efforts. It also is believed that the differences in programs for each effect, where they exist, should be delineated so that future use may determine which hydraulic effect is the more relevant. It is the purpose of this paper to: (1) show the theoretical maximum bit hydraulic horsepower, jet impact force and jet velocity available at all depths, taking into consideration all necessary restrictions on operating conditions; (2) illustrate procedures by which the maximum available horsepower, impact force or veIocity may be obtained; and (3) present a graphical method for rapid selection of jet-nozzle sizes and flow rates to be used with conventional procedures to design jet-bit programs for maximum bit horsepower, impact force or velocity as desired.

By Oliver Bowles

"A New Mica Company in China A report has been received from the American Consulate at Chungking, China, to the affect that a new company has been organized to operate a mica mine north of Ta-chien-lu, in the province of Ssu-Chuan. The company, which is entirely under Chinese management and control, has a working capital of $10,000. While comparatively new, the mine has been worked before, and apparently with some success. The mica is said to be of good quality. It is claimed that the deposit will supply a limited amount of mica that will cut in pieces a foot square or over, and larger quantities of smaller sizes. The chief difficulty is transportation, for it is reported that a ten days' journey, part of it over mountain trails, will be necessary to transport the mica from the mine to Yachow, the nearest practical waterway. It is probable, therefore, that the output of the mine will be limited.Necessity for Careful Trimming and Grading of MicaA recent report to the Department of Trade and Commerce, Ottawa, Canada, by Acting Trade Commissioner C. G. Venus, London, England, contains information which is of vital interest to mica producers in the United States. It is pointed out that mica exports from Canada to England show a gradual decline dur¬ing recent years, the figures being as follows: 1913- 1,383 cwt: 1914 - 1,225 cwt: 1915 - 1,864 cwt: 1S16 - 879 cwt: 1917 444 cwt: 1918 - 480 cwt. Shipments from India to England, on the other hand, show a steady increase from 40,178 cwt. in 1913 to 66,401 cwt, in 1918."

Jan 1, 1920

By William J. Campbell

Three types of X-ray analytical instrumentation were compared for applications in the secondary brass and bronze industry. The instruments were a conventional X-ray spectrograph, a portable X-ray spectrograph, and a radioiso-topic X-ray analyzer using balanced filters. The following two general applications were considered: Rapid identification for sorting scrap metals and quantitative analyses to provide guidance in the melting and casting of alloys. Twenty-three analyzed copper-base alloys were used as standards. Although the alloys varied widely in composition, matrix correction procedures were not necessary except for copper. The conventional X-ray spectrograph provides positive identification of the alloys and quantitative values for the six elements investigated--aluminum, copper, iron, lead, tin, and zinc. Equivalent results were obtained with the portable X-ray spectrograph for those elements whose characteristic X-rays are in the wavelength range of the instrument. The radioisotopic X-ray analyzer distinguishes certain groups of alloys and provides quantitative determinations for copper, lead, tin, and zinc. The sensitivity of the analyzer was marginal for the determination of small concentrations of elements of atomic number 26 or lower.

Jan 1, 1972

By Greg Beckstrom

On Oct. 1-3, SME?s Twin Cities chapter (SME TC), in cooperation with the University of Minnesota ? Duluth?s Precambrian Research Center (UMD-PRC), cohosted a symposium on silica sand mining and processing. The conference was held at the Earle Brown Heritage Center near Minneapolis. The symposium was followed by a day-long field trip to operating mines, processing plants and loading facilities located in southwestern Wisconsin. Speakers and attendees at the symposium included university professors, industry experts, regulators, mining company representatives, equipment suppliers, consulting engineers and service companies. Approximately 320 people attended the conference. In addition, about 50 people who oppose mine development and the oil and gas industry showed up to voice their displeasure with the event and those companies that operate in this space.

Jan 1, 2012

By Jeffery L. Kohler

A method of monitoring production, information, i.e., raw tonnage and machine state, from each working section has been developed. The method is based on the sensing of electrical parameters in each section load center, and the reporting of this information through the existing mine-wide monitoring system. A decision-theoretic type of pattern classification technique has been used to define the machine states. The basis of the method is presented in this paper, along with a proposed hardware and software implementation scheme. Information issues central to the development and use of the proposed production monitoring system are also discussed.

Jan 1, 1988

By Charles G. Kemsley

IN view of the truly remarkable development of special steels for special purposes, the mining industry has for years looked forward to a time when steel makers would come forward with a product which would be an improvement over the straight carbon steel which has always held the field for drilling rock. In order to avoid making changes in conventional shop practice, the industry has perhaps been too insistent upon obtaining a water hardening steel which could be handled in the blacksmith shop by long established methods. As early as 1932 or 1933, an oil-hardening tool-steel of the one per cent carbon, plus chrome, plus molybdenum type was applied to hollow drill steel. It was known as a hard as well as a tough steel, and one that, theoretically, should give a good account of itself as a rock drill, if properly heat-treated; and so it has proved in actual trials. There were numerous deterrents which retarded adoption of this steel. For several years there has been a constant improvement in the drilling qualities of the straight carbon steel, and, considering the higher unit price ? of the alloy, there has been considerable doubt in the minds of some mining? men as to what advantage there might be in the use of alloy over straight carbon for hollow drill steel. The alloy being an oil-hardening steel, its adoption meant having two kinds of steel in the mine, for a time, and that spelled trouble, unless some positive means of identification was adopted. The hardening and forging ranges of alloy steel being narrow also made necessary much closer control over these operations if poor results were to be avoided. These thoughts undoubtedly prevented its use becoming wide-spread, for, as a matter of actual record, less than fifteen per cent of all the hollow drill steel used in Canada today is alloy.

Jan 1, 1942

By James R. Arnold

Over the past few years several commercial wetting agents and drying aids have been tested in the lab and in the plant at Gold Fields Mining's operations at Mesquite and Ortiz. The major goal was to increase recovery with these surfactants by improving the permeability of the pad and increasing the rate of penetration through the rock.

Jan 1, 1988

By K. L. Morton

This technical note reviews the status quo of mud rushes and flooding, which have claimed them lives of many people in underground mines in South Africa and globally. Given that the causes are well known and can be managed, the note calls for the development of a national and global standard on flood and mud rush prevention in order to save lives.

Mar 30, 2026

By Juan L. Yarmuch, Gonzalo Sepulveda

Medium- and short-term mine planning holds immense significance in optimizing production and resource utilization. It serves as a vital link between the long-term strategic plans and the day-to-day operational activities of a mine. In this context, a mathematical formulation is proposed to incorporate mining width constraints into the production scheduling process, aiming to maximize the net present value (NPV) of the schedule while ensuring enough room for the operation of mining equipment.

Jul 1, 2024

By T. M. Russell

"Face mapping is a simple but invaluable means of geological and geotechnical data acquisition whereby intact rock properties, rock mass properties, discontinuity properties, and structural orientation can be assessed. Although traditionally done via direct contact with the mapping face through techniques such as line mapping or window mapping, remote face mapping using various digital techniques has become increasingly popular in recent years. Sishen is a large open pit mining operation requiring a comprehensive geotechnical data-set to evaluate pit wall design and stability with the necessary level of confidence. Geotechnical borehole data, face mapping data, geotechnical laboratory testing data, and implicit structural models provide the main sources of this information. Although a large geotechnical borehole database has always been maintained at the mine, face mapping has in the past been restricted to sporadic and isolated stability assessments. In 2013 the mine acquired a terrestrial laser scanner with the resolution, photographic capabilities, and software required to carry out geotechnical face mapping. A face mapping procedure was set up based on accepted face mapping methods, the data requirements of the mine, and capabilities of the laser scanner system. Mapping data obtained from the scans was integrated into the Acquire geological data management system, a purpose-designed structured query language (SQL) database system used for storing the mine’s geotechnical data. Within the geotechnical design process, having face mapping data available has improved confidence in the properties of the rock mass and structural environment, allowing for better definition of geotechnical design sectors. Overall, the face mapping and geotechnical analysis features of the terrestrial laser scanner in use make it an invaluable geotechnical data capture tool, provided a system is in place to store mapping data in a manner that allows for meaningful rock mass and structural information to be produced. IntroductionFundamental to the geotechnical design process is the acquisition of a reliable and complete geotechnical data-set. Geotechnical data acquisition will typically commence during the early stages of a project and continue well into the operational life of the mine, with the data confidence progressively increasing as the amount of data captured increases. Sishen mine currently bases all open pit geotechnical designs and geotechnical risk assessment on geotechnical borehole data in conjunction with interpreted structural models. Boreholes are logged and the data is captured in an ongoing process. This process forms the initial step in the geotechnical design and risk assessment process whereby the raw data is used to classify the strength properties for each lithology, provide inputs for geotechnical block models, and ultimately provide the inputs for slope design analyses. To date, borehole data has provided the only largescale, organized data-set for input into geotechnical analyses at Sishen. Although borehole data is the best and most comprehensive form of geotechnical data, there are some shortfalls that can be addressed by other data collection methods. These shortfalls are as follows."

Jan 1, 2018

By Paul E. Loustaunau

This report describes a project in which three structured underground coal mine equipment operator training programs were developed. The project was carried out in two parts. In the first part, a research study was conducted to determine how on-the-job training is currently conducted in industry, and to determine the overall effectiveness of current on-the-job training. In addition, the possible application of the principles of social learning theory to on-the-job training was investigated. In the second part three prototypes on-the-job training programs were developed for shuttle car operation, roof bolter operation, and continuous miner operation. These programs were carefully structured to eliminate the shortcomings of current industrial on-the-job training identified in the research study and incorporated the application of relevant principles of social learning theory. The programs are prototypes which underground coal mine training personnel can use as models to develop their own customized equipment operator training programs.

Jan 1, 1983