Search Documents

By S. Spigarelli

The creep response of the AE44 magnesium alloy was studied by means of constant load creep tests carried out at 125 and 150°C, obtaining that at the latter temperature the minimum creep rate observed under an applied stress of 100 MPa was two orders of magnitude lower in the investigated alloy than in AM50. The minimum creep rate dependence on applied stress was described by a conventional power-law, e = Aon , where A was a temperature dependent parameter and n was the stress exponent, resulting in a n value close to 30, i.e. by far larger than those observed in commercial alloys with similar Al content. This large difference in creep response was attributed to the precipitation of rare earths (RE) intermetallic phases distributed in the grain boundary zone in form of an almost continuous network of dispersoids that were observed by means of scanning electron microscopy.

Jan 1, 2006

By A. M. Bell

"The property of Gaspe Copper Mines, Limited, is in the Gaspe Peninsula some 60 miles west of the town of Gaspe and 20 miles in from the north coast. The Copper Mountain deposit was first discovered in 1921 and first optioned and drilled by Noranda in 1938. The Upper Needle Mountain showings a mile south were found in 1938, but it was not until after a delay of 10 years that the more important deep ore at Needle Mountain was located by drilling. Production started in 1955, and the smelter commenced operation in December. Mining is by open stope methods with first production coming from the Lower Needle Mountain orebody, of which only a small portion has been exposed in underground openings.Stratigraphy and AlterationThe country rock is composed of limy siltstones of Devonian age. Away from alteration these are dark and generally carbonaceous. Throughout the drilled area numerous narrow layers of tuffaceous fragmental material occur, and such beds are found to provide excellent horizon markers by virtue of their uniform thickness and wide lateral distribution. These markers are valuable for stope control in mining the bedded replacement deposits.Intruding the sediments at Copper Mountain are porphyry dykes, and one drill hole encountered granite 1,400 feet below the valley. Solutions responsible for the rock alteration and ore deposits seem to have emanated from this intrusive centre.On the mine claims strong hydrothermal alteration has completely obscured the original character of the sediments. The unaltered formations are all very similar in appearance, but following alteration rocks that are very dissimilar in physical characteristics are produced, and such differences have an important influence on ore deposition. The alteration effects are known to extend over a vertical range in excess of 3,000 feet and have a surface area of two square miles. All known ore bodies are within the zone of alteration. In this, rocks are strikingly bleached to a white colour in contrast to the normal dark-coloured sediments, and are much harder and more abrasive, with bedding often obscured. The first effect of alteration is driving off of carbonaceous matter, followed progressively by silicification in the acid rocks and by the formation of lime silicates in the lime rocks, with an accompanying gain in silica and a corresponding loss in lime. Extensive analysis has shown that there is an actual addition of silica involved in the alteration."

Jan 1, 1949

By AIME AIME

BEFORE proceeding with the papers scheduled for the ore and foundry session*, the teller's report on the election of officers for the ensuing year was presented, a; follows: Chairman. G.C. F. MacKenzie; vice-chairmen, C.S. Robinson, J. T. MacKenzzie, C. E. Meissner; executive committee, A. L. Field, R. F. Harrington, E. F. Kenney lit. Waterhouse announced that the fall meeting will be devoted to alloy steel. This meeting will be held in Chicago the week of Sept. 22 in connection with the National Metal Congress. He also announced that oxygen in steel will be the central idea of the meeting which will be held in New York next February. The first paper, entitled "Sintering Limonitic Iron Ore at Ironton, Minn.," was presented by Perry G. Harrison (T. P. 284), the author. Sintering was first un¬dertaken in 1024 to treat Cuyuna range iron and manganiferous ores low in silica and high in moisture and containing objectionable qualities of fine... A Dwight-Lloyd machine was first installed. This machine was replaced by a larger one having a width of 72 in. The power cost was decreased from about $11.22 per ton of sinter on a 42-in. machine to about X0.14 for the 72-in. machine. The tons of sinter per man-shift was increased from 11.86 to 16.77. Improvements embodied in the larger plant reduced the cost of sintering to $0.41. The analyses of iron ore and manganiferous ore and the sinter produced from these materials was used to show the increase in value at the mine resulting from sintering. Crude iron ore actually unsalable was increased in value f.o.b. mine from a theoretical figure

Jan 1, 1930

By Mine F. J, Woods P. H

Waste waters from mine sites may be screened for all constituents of significance as a first step in establishing water quality criteria for protection of aquatic ecosystems. Inductively-coupled plasma mass spectrometry (ICP-MS) offers the capability to screen water samples and digest solutions for virtually all elements in the periodic table. This technique is therefore able to identify elements whose concentrations are elevated in waste waters and may be rarely present in background surface or ground waters. Such elements may be present in waters at only a few ¦g/L. ICP-MS has sufficient sensitivity to detect sub-¦g/L or even ng/L levels of many elements. Waste waters from most mining activities in the Northern Territory have been examined by ICP-MS. The concentration data provide the basis of a contaminant data base. The data can show specific tracers in the ore or mineral itself, subsequently found in waste water. An example is the presence of rhenium in uranium ore. Such trace elements may be present in soluble or insoluble chemical forms and are more useful as indicators when soluble and exemplifying conservative chemical behaviour. The approach described, based on ICP-MS screening of mine site waste waters, together with general physico-chemical variables, provides the most comprehensive means yet available of selecting variables for monitoring programs and ensures that key elements and/or their chemical species are not excluded from monitoring programs.

Jan 1, 1994

By Oliver Bowles

The United States Bureau of Mines has within its ranks a group of engi- neers who are engaged in working out quarry problems, the solution of which will be of general benefit to the industries involved. The problems undertaken are approached in a systematic and thorough manner, all the evidence for and against any proposed change or new development being collected as carefully as an attor- ney would prepare his data on an important case. Unlike the attorney, however, the Bureau engineer does not take sides; his judgment is based entirely and in- partially on the array of facts presented. In order to gain the desired infor- mation he visits many plants, consults with the leaders in the industry, works out experiments in his laboratory, and supplements this information with a stu- dy of all available literature already published on the subject in any part of the world. As an engineer who has for eight years conducted such inquiries in the stone industry, I propose to discuss the Bureau of Mines viewpoint; and it may be of interest to consider with me in a brief and general way the engineer's method of looking at quarry problems, and some of the results attained through past and present labors. While the Bureau has conducted no investigation directly for the crushed- st one industries, two years of investigative work at cement-plant quarries, and work now being conducted at lire-plant quarries, has a very direct bearing on the problems of the crushed-stone industry, since stripping, drilling, blasting, loading, and transportation are similar in many respects in all stone quarries. The results of cement-plant quarry investigations are to be found in Bureau of Mines Bulletin #160. (b) Two short papers on lime-plant quarry problems have been issued in mimeographed form as Serial #01 (c) and Serial 3 (d).

Jan 1, 1923

By Richard V. Ageton

Compressed- air blowers are frequently used both in large and small metal ines , not only as an aid to ventilation , but in some mines as a substitute for an dequate ventilation system . As a temporary fixture , blowers have their uses , but hey should never be used in lieu of a permanent ventilation system. A number Probably the most common error made in placing dependence on compressed- air lowers as an aid to underground ventilation is the tendency to over- rate their cooling efficiency . It is a very common but natural error to assume that compressed air which issues freely from a blower is of the same temperature as the compressed air which issues freely from the exhaust port of a rock-drilling machine . of readings were taken in different mines of the temperature of the rock- drill exhaust , of the compressed air flowing from the blowers , and of the surrounding air In both cases . In general , the temperature of the rock- drill exhaust was from 10 to 30 degrees below that of the surrounding air , in many instances being slightly below freezing , 32° F . The average temperature for a number of compressed-air lowers and for the mine air surrounding them is shown in Table I.

Jan 1, 1922

By Anil Saigal, Jr. Fuller, Said Jahanmir

"All-ceramic crowns, including glass-infiltrated spinel composites, are coming into widespread use because of their superior aesthetics and chemical inertness. This study investigates the residual stresses that are developed in these composites as a result of cool down from the glass-infiltration temperature to room temperature due to slight mismatch in the coefficients of thermal expansion and its effect on the mechanical behavior of these composites. Two-dimensional finite element simulations were performed using an object oriented finite element program OOF. The OOF program is a combination of two programs. The first program, PPM200F, is designed to read an image file such as a micrograph. The individual pixels that constitute the micrograph may be collected into groups and their material properties assigned. PPM200F is then used to create the finite element model/mesh that OOF then reads. The average residual stresses are found to be tensile in the spinel matrix and compressive in the infiltrated-glass. There is large variation in residual stresses and strains from location to location with presence of locations at which the glass is under tensile stress. The crack initiation and initial propagation in glass-spinel composites is at the glass-spinel interface in both the glass and the spinel. The presence of residual stresses can lead to lower crack initiation stresses and degrade the mechanical properties of the composites.IntroductionGlass-infiltrated spinel ceramics are in clinical use as core materials in all-ceramic crowns and as inlays and onlays (1-3). Advantages of ceramic composites include near net-shape forming with high strength in the infiltrated state. Besides, spinel is quite translucent and may potentially be used without a veneer. However, these ceramic composites are subject to damage accumulation from repeat oral contact loading and often fail after a few years of use (4). This paper examines the residual stresses that are developed in these composites, after cooldown from the glass infiltration temperature to room temperature, due to the slight mismatch in the coefficients of the thermal expansion of the two phases."

Jan 1, 2001

By Luiz Guilherme Isfer Maciel, Marilena Cardu, Fernando Golin, Jacopo Seccatore

"This study applies the concept of the difficulty of tunnelling by drilling an blasting (D&B) to selectedcases from the Brazilian tunnelling industry. The difficulty of tunnelling has been defined in previouswork as the difference of specific drilling (SD) from industrial average trend: easier when SD is lowerthan average, more difficult when SD is higher than average. Results show how tunnels in Brazil tend tobe unrealistically more difficult to excavate when compared to similar excavations in similar geologies elsewhere in the world. It is thoroughly discussed the reason for such anomaly (up to +90% SD compared to industrial average). One reason could be the lack of options amongst explosive products on the brazilian market. Only ANFO and explosive emulsions are available in Brazil. Lacking high VOD(Velocity of Detonation) products might result in reducing the maximum allowable burden amongstproduction holes, therefore increasing SD. Another reason could be found in the tunnel designers’tendency of choosing D&B as excavation method for weak rock masses that would benefit from mechanical excavation. The reason to this tendency can be partly found in the lack of availability of mechanical excavation machines in the brazilian market. Blasting in weak rock masses requires more careful smooth blasting, hence a closer spacing amongst contour holes to avoid costly overbreak: this increases SD. A third reason could be found in the lack of skill amongst the local workforce. When dealing with unskilled workers the blast designers naturally tend to avoid highly optimized blasts thatrequire very skilled workforce to be realized on field. The designer in this case tends to leave the blastdesign simpler but more robust, at the cost of higher specific drilling and specific charge. The conclusions suggest that this unrealistic difficulty when compared to world average could be a simptom of the so-called “Brazilian cost” within the tunnelling industry."

Jan 1, 2017

In most States of Australia it is a legislative requirement for underground mines to have a separate means of egress from the normal means of ingress to permit the safe evacuation of workers to the surface in event of an emergency. Such egress may be in the form of a ladderway equipped shaft/underlie or trafficable incline/decline. Additionally, there is a general requirement to have one or more airways, separate to the main shaft or other principal entrance of an underground mine, extending to the lowest level to permit ventilation to all parts of the mine. Fulfilling these requirement is difficult in the development phase of a mine when access underground is achievable by only a shaft or decline in the process by being sunk. What is frequently practiced in Australia is for production to then commence, sometimes in association with continuing development, in the same configuration without the establishment of this separate method of egress to the surface nor additional airway/s with reliance on refuge chambers to cater for back up in any emergency. Not only, could this jeopardise the health and safety of workers in case of an underground emergency it could be construed as a statutory breach of legislation. While recognising that refuge chambers are often used throughout underground operations nowadays their equipping and the criteria for their location needs to be bought into focus. This presentation discusses how such legislative requirement can be met alongside the use and appropriateness of refuge chambers.

Jan 1, 1998

By S. D. Rosenthal

"This paper will share my ‘shift in career direction’ journey from corporate mine engineer, with 31 years of mining various commodities with a wide range of responsibilities in a variety of countries, to the world of academia. There are times in one’s career that a change is required, albeit perhaps not as drastic of a change as moving to teaching. This paper will share how the transition arose, the decision to make the change, the challenges of the first year in academia, and the journey within academia going into the second year. INTRODUCTION As a graduate of the Montana College of Mineral Science and Technology (Montana Tech) with a B.S. Mining Engineering degree in May of 1982, my first job with Utah International in the Farmington area took me back to my home state of New Mexico. Some of you will remember that the early 1980’s was not a period of prolific opportunities for mining engineers; given low commodity prices, especially for copper (for example, Anaconda Company had been taken over by Arco and was in the midst of closing down its Butte operations). Coal was good and the learning opportunities abounded with Utah (which became BHP and then BHP Billiton). Gold was taking off in the mid to late 1980’s thanks to use of cyanide and heap leaching technology improvements, coupled with deregulation of the gold price, so I ventured off to work in the gold industry with a (then) junior Canadian company called Barrick at a new acquisition of theirs known as Goldstrike. That same gold surge was causing a shortage of iron ore mining engineers in Australia so after a few years in Nevada, I uprooted the family and left for a little town in the Pilbara of West Australia, known as Newman, to work in the iron ore industry with BHP Iron Ore. An initial short overseas posting turned into six plus years before transferring to BHP’s Indonesian steam coal mines in Kalimantan on the island of Borneo. BHP was going through a rough period following some ill-fated projects (Magma copper purchase, Beanup and HBI) and was reviewing assets and staffing so internal opportunities became scarce. Employees were encouraged to ‘leave the company and find work elsewhere.’ So, off I go to Argentina to try copper mining in the Andes with Minera Alumbrera. This short stint in South America was followed by a move to another mining town, Morenci, Arizona, and a posting with Phelps Dodge (now Freeport McMoran). After 12+ years without living close to snow we moved to the Denver area in a new position with Newmont Mining Corporation. Along the way I became a Professional Engineer (Nevada) and completed a Masters in Project Engineering and Management. After 11 years with Newmont, I moved to Butte, Montana where I accepted a position as Assistant Professor of Mining Engineering."

Jan 1, 2015

By S. D. Rosenthal

"This article will share my ‘shift in career direction’ journey from corporate mine engineer, with 31 years of mining various commodities with a wide range of responsibilities in a variety of countries, to the world of academia. There are times in one’s career that a change is required, albeit perhaps not as drastic of a change as moving to teaching. This paper will share how the transition arose, the decision to make the change, the challenges of the first year in academia and the journey within academia going into the second year.As a graduate of the Montana College of Mineral Science and Technology (Montana Tech) with a B.S. mining engineering degree in May of 1982, my first job with Utah International in the Farmington, NM area took me back to my home state of New Mexico. Some of you will remember that the early 1980s was not a period of prolific opportunities for mining engineers, given low commodity prices, especially for copper (for example, Anaconda Co. had been taken over by Arco and was in the midst of closing down its Butte operations). Coal was good and the learning opportunities abounded with Utah (which became BHP and then BHP Billiton).Gold was taking off in the mid to late 1980s thanks to use of cyanide and heap leaching technology improvements, coupled with deregulation of the gold price, so I ventured off to work in the gold industry with a (then) junior Canadian company called Barrick at a new acquisition of theirs known as Goldstrike. That same gold surge was causing a shortage of iron ore mining engineers in Australia. So after a few years in Nevada, I uprooted the family and left for a little town in the Pilbara of West Australia, known as Newman, to work in the iron ore industry with BHP Iron Ore. An initial short overseas posting turned into six plus years before transferring to BHP’s Indonesian steam coal mines in Kalimantan on the island of Borneo. BHP was going through a rough period following some ill-fated projects (Magma Copper purchase, Beanup and HBI) and was reviewing assets and staffing, so internal opportunities became scarce. Employees were encouraged to “leave the company and find work elsewhere.” So, off I went to Argentina to try copper mining in the Andes with Minera Alumbrera. This short stint in South America was followed by a move to another mining town, Morenci, AZ, and a posting with Phelps Dodge (now Freeport- McMoRan). After 12-plus years without living close to snow, we moved to the Denver, CO area in a new position with Newmont Mining Corp. Along the way I became a professional engineer (Nevada) and completed a masters in project engineering and management. After 11 years with Newmont, I moved to Butte, MT where I accepted a position as assistant professor of mining engineering."

Jan 1, 2015

By L. Narhi, K. Haavanlammi

"Approximately two thirds of annual nickel production is used as a raw material in the making of stainless steel, and about 60% of these nickel products are in the form of metallic nickel such as nickel cathode or briquettes. In the stainless-steel production process nickel is blended with iron and chrome-based raw materials, and metallic nickel is typically only required for final steel fine-tuning. Outotec offers a new FeCrNi technology to enhance the nickel value chain for stainless steel producers. This involves the use of an HPAL-based intermediate nickel product (e.g., mixed hydroxides or NiO) as raw material in the Outotec FeCrNi process, for the production of a FeCrNi Master Alloy. The new process, designated as the FeCrNi process, offers multiple benefits compared to existing technologies such as: higher tolerance for impurities in the HPAL intermediate product, avoiding the need for further nickel refining, and the improved recovery of all metals in the FeCr process. The complete new FeCrNi value chain is based on proven technologies such as HPAL and the Outotec FeCr-process. This new innovative and promising value chain offers improved efficiencies for the HPAL based nickel production process combined with excellent sustainability aspects.INTRODUCTION In today’s global economy there is a constant need to improve the efficiency and sustainability of the metals production. The requirements for modern metal refining are tightening and cost efficient, safe and sustainable operation is the precondition for all investment. Outotec is offering now a novel way to combine FeCr and Nickel production to create a completely new value chain to source nickel to stainless steel. BACKGROUND Nickel The current nickel mine production is in the level of 2,000 tons annually and it is split 44% from sulphide based deposits and 56% from laterite deposits (Figure 1). Most (40%) of the nickel is refined to pure nickel metal whereas other products are FeNi (19%) and Nickel Pig Iron NPI (20%) (Roskill). The remaining part, roughly 21%, is nickel chemicals and intermediates. Most of the new investments in nickel are in the direct shipping of laterite to produce nickel pig iron. HPAL process is considered in few projects but no major HPAL projects have been started since the Ambatovy plant in Madagascar. Ambatovy reached the commercial production in 2014. The main primary nickel used is stainless steel manufacturing. In the year 2016 about 68% (~1,360 kt) of primary nickel production was used in stainless steel."

Jan 1, 2017

By Theodore B. Counselman

Of all natural resources, iron ore made into steel is the most important both in tonnage and value. The primary reason for the prosperity of the United States in the last century has been its pre-eminence in domestic supplies of iron ore and steel. The depletion of these reserves by two world wars and by the demand for richer blast furnace charges, as well as the constantly growing world- wide demand for steel, has fostered the recent quest for new iron ore mines around the globe. These developments have made a dramatic change in the iron ore picture of the world. It is the purpose here, however, to look briefly at the development of the United States iron ore industry, which has played such an important role in the events leading to the modern day boom in iron ore exploration.

Jan 7, 1965

By Sandy Worden

Coal mining companies in Australia are managing the high-consequence risks across their operations more effectively by using an interactive online risk management system known as Riskgate Developed by the Minerals Industry Safety and Health Centre (MISHC) at the University of Queensland, Australia, Riskgate contains detailed information about 11 high-consequence risk areas (called topics in the system) for opencut and underground coal mines (Table 1). The existing topics are: fires; strata control for underground mining; ground control for opencut mining; tires; isolation; collisions; explosions and explosives; manual tasks; and trips, slips and falls. Every Riskgate topic is focused on coal industry activities (mining, processing, transport and storage). The scope includes mine sites, lease areas and mine infrastructure (mobile, fixed plant, field equipment, buildings, road and rail transport), and all aspects of the mine life cycle from design through to decommissioning. The topics uniformly recognize that a loss of control can result in injury or fatality, equipment damage, production loss, reputation loss and environmental damage. However, the priority focus for Riskgate is the safety of mine personnel.

Jul 1, 2013

By H. Rosenthal, A. L. Jamieson

The action of mercury on stressed brass to produce cracks was known before Moore, Beckinsale and Mallinson1 showed that actual season cracking did not occur spontaneously but could be induced by ammonia. These investigators studied other substances, including diphenylamine, without finding that anything other than ammonia could cause season cracking Grimston2 reported season cracking in cartridge cases stored in wooden boxes wetted with dilute sulphuric acid pickling solution. Season cracking associated with sulphur dioxide, water vapor and air has been reported by Johnston,3 although he reported that trimethylamine and pyridine did not cause cracking. Jevons4 has ascribed season cracking of brass in certain instances to trimethylamine, "aldehyde amine," "ketone amine" and pyridine, but no experimental work was done evidently to prove this definitely. Pyridine was investigated by Morris,5 who found it to have considerable cracking power. In the present investigation, the object was a qualitative evaluation of a number of representative amines with respect to their ability to cause season cracking. Thus it was desired only that an appreciable vapor pressure of each amine be obtained in order to make the test as severe as possible, without attempting to test equivalent concentrations for comparative purposes. MEthods Specimens TWO types of specimen were used: 1. Unannealed 70-30 brass CUPs formed from 0.040-in. thick sheet. Height of cup Was 13/8 in. and diameter was 17/8 inches. 2. First draw pieces of caliber .50 cartridge cases in the unannealed condition (70-30 brass)- The cups were representative of a thin wall and thin base specimen, whereas the draw pieces have a thick base (1/4 in.) and a thick wall (approximately 3/32 in.). Both types of specimens contained high residual stress and cracked in less than one minute in a solution of I per cent mercurous nitrate and I per cent nitric acid provided that this was receded by a 30-sec. pickle in 40 per cent nitric acid. Specimens were prepared as follows: (1) degreased in trichlorethylene, (2) rinsed in H2O, (3) pickled 5 min. in 10 per cent by volume H2SO4 (1.84 SP. gr.), (4) rinsed in H2O, and (5) dried. Amirtes Tested In selecting the amines, representatives of the three series of amines, and one series of substituted amines were chosen. The aliphatic series was represented by the methyl and ethyl primary, secondary and tertiary amines. These are the simplest aliphatic amines. For the aromatic series, the phenyl primary, secondary and tertiary amines were selected as being the simplest. The heterocyclic series was represented by pyridine, which is a simple heterocyclic base (tertiary amine).

Jan 1, 1944

By D. Brunner

System simulation is an increasingly popular technique for analyzing and improving existing as well as newly designed underground mining operations. An engineering firm that specializes in simulation helped a major metals producer build a long-range planning model of an existing underground mine. Subsequently the team adapted this model to assess technology alternatives in the design of a new mine. The two models differ in the level of detail used for modeling the development process. This paper discusses the differences in approach between the models along with the experiences gained and challenges faced during the construction and use of the models.

Jan 1, 1999

By George A. Roche

Since our firm was established by Mr. Price in 1937, we have followed an investment philosophy which is based on the belief that investment in growth stocks is the most assured way of achieving superior, long term investment accomplishment. There are many criteria that we use to select growth companies but the most important is a combination of superior management operating in an industry with above average growth potential. This growth stock approach is the cornerstone of our investment strategy for two of the three mutual funds sponsored by the Price organization and for our private clients. However, during the past 5 years we have seen inflation accelerate due to a variety of factors including the inability of our government to meet seemingly unlimited needs with limited revenue sources. While there might be temporary periods of price stability, we believe that inflation will still continue to be the investor's greatest problem in future years. Our conviction that inflation would increase combined with the acceleration of inflation in the late 1960s stimulated an intensive investment research effort, on our part, to identify those companies with strong natural resource bases -- who own or control large, secure, and low cost tangible assets. Over the longer term and in an environment of a depreciating dollar some of these firms should be able to develop and sell these assets at higher prices. While we still believe that investing in growth companies is a sound investment strategy to offset inflation, we also believe that certain natural resource companies will show well above average investment performance. In the newest Price mutual fund, The Rowe Price New Era Fund, we have, as a matter of policy, placed a large portion of the portfolio in natural resource companies.

Jan 1, 1972

By B. Waterman, R. Collins, V. R. K. Paruchuri, P. Gonzalez, H. Dijkman

"INTRODUCTION Mining and processing of sulfide ore bodies has the potential to solubilize sulfate. Gypsum in the host rock, as well as oxidation of sulfides during milling and processing can solubilize sulfate. Acid rock drainage (ARD) also has the potential to generate waters high in sulfate. Even after treatment of the ARD with lime, the treated water can have sulfate present in gypsum saturation levels. Most mine-sites reuse sulfate impacted water but as a mine nears closure, reuse options may be limited and water treatment becomes an option. Furthermore, sulfate discharge requirements, particularly for anti-degredation narrative standards, can be very strict. Freeport has investigated many new technologies to economically remove sulfate from these types of water. A Dutch company, Paques B.V. developed one of these technologies and it utilized biological reactors to convert sulfate into elemental sulfur in a 2-step process. In 1992 the first industrial reference of the SULFATEQTM technology was commissioned at the Nystar Budel zinc refinery in the Netherlands. PILOT PLANT TECHNOLOGY AND DESCRIPTION As shown in Figure 1, the plant contains several process steps, which can mainly be divided into the following sections: 1. Anaerobic biological system in which sulfate is reduced to hydrogen sulfide by sulfate reducing bacteria. 2. Aerobic biological system in which hydrogen sulfide is oxidized to elemental sulfur by sulfide oxidizing bacteria. 3. Solid/liquid separation in which sulfur, calcium carbonate and biomass solids are separated and dewatered. Sulfate impacted ground water is pumped to the feed water tank through a plate and frame heat exchanger to maintain the solution temperature around 95°F. A custom mix of micronutrients is dosed to the feed tank. This nutrient mixture provides essential elements for the growth of anaerobic and aerobic biomass. Urea is added to the feed tank and provides the required nitrogen source to the biomasses. The pretreated feed water is pumped into the anaerobic reactor. The reactor works on the gas lift principle. Sulfate reducing bacteria utilize hydrogen gas as electron donors and reduce sulfate to hydrogen sulfide. This reaction increases the alkalinity of the solution. Carbon dioxide gas is added in order to control the pH within working range of the reactor. Due to the low solubility of the hydrogen gas, the anaerobic gas mixture is recycled through the system. The gas mixture recycle also provides the gas lift for mixing within the anaerobic reactor."

Jan 1, 2016

By LEWIS F. THOMAS

MINING geologists and mining engineer, rarely give due thought to the geography of mining deposits. They realize, it is true that what may be ore in one place would be only worthless rock in another because f the in accessibility of a smelter r a market; and they may consider the lack of a supply of labor, or water, or power to carry on operations. But they do not think (of these things in terms of geography. Geography may be defined as the science of relationships between earth and man, so geographers are vitally interested in the how and why of mining as it is carried on at different place, having entirely different environment-. Such environments are geographic complexes or composites of natural and cultural elements, which are listed and briefly discussed in the following paragraphs.

Jan 1, 1941

By Sandra L. Mesa-Espitia, Gretchen T. Lapidus

Gold present in arsenopyrite matrices is refractory and requires highly oxidative pretreatments in order to obtain acceptable degrees of extraction. However, these release many byproducts that are harmful to the environment. In the present work, a high-grade arsenopyritic ore was pretreated with different solutions, containing hydroxide ion, EDTA, oxalic, tartaric, or citric acids, to improve gold extractions in a posterior leaching step. The pretreatments were carried out at room temperature for 24 hours with a respective ligand concentration of 0.25 M. Once completed, the residue was leached in a thiosulfate solution to quantify the effect of the pretreatment on gold extraction. Only 29% of the gold content was leached, with very slow kinetics, in the untreated mineral. However, after pretreatment with tartaric or citric acid, the kinetics improved, although the percentage of gold extraction only reached 42-45%. The highest gold recovery, with very rapid kinetics, was found with the oxalic acid or the hydroxyl ion pretreatment (70 and 62%), respectively, but also corresponded to the most arsenic co-dissolution.

Jan 1, 2014