Search Documents

By P Craig, I Canbulat, J Naylor, J Emery, A Sykes

Longwall mining is by far the most common method of underground coal extraction in Australia. Industry trends and expectations are placing increasing emphasis on the reliability and productivity of these operations. Longwalls are becoming wider and longer while retreat rates are continuously increasing due to significant improvements achieved in longwall equipment reliability and automation. This increased longwall productivity is placing significant emphasis on the reliability of longwall panel development.Although there have been significant improvements in the reliability of continuous miners and hydraulic drill rigs, the traditional resin-encapsulated bolt installation is still the principal method used in all major coal producing countries around the world. Anglo American realised that an opportunity existed to introduce an alternative roof bolt installation technique called ‘spin-to-stall’ (STS) into Australia. STS was first introduced by Anglo American Coal in South Africa, where it has been successfully used for over a decade, though implementation of South African STS resin in Australia has proven to be near impossible. Therefore, a new STS development project was initiated between Anglo American Coal and Jennmar Australia. This paper summarises the journey of this project, the results achieved and the successful implementation of STS at Grasstree mine.CITATION:Emery, J, Canbulat, I, Craig, P, Naylor, J and Sykes, A, 2014. Development and implementation of spin-to-stall resin at Anglo American’s Australian Underground Coal Operations, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 287–294 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By E. H. Denny

Colorado coal-mine fatalities, which have gradually decreased since 1914, have shown a marked decline since 1924. Data on coal-mine fatalities in Colorado published by the U. S. Bureau of Mines5 indicate that the deaths per thousand 300-day workers have decreased from 9.13 in 114 to 6.14 in 1926, and that the deaths per million tons produced have decreased from 9.18 in 1914 to 4.98 in 1926. Table 1 gives fatality rates in Colorado and in the United States from 1914 to 1926 inclusive. [ ]

Jan 1, 1929

By James P. Roe

I. INTRODUCTION. THOSE who deem the subject of this paper an old and super¬seded one may recall with advantage the words of the great proverb-maker, bidding us to seek the new in the ashes of the old. The manufacture of wrought-iron began with the small hearth built upon an eminence, and relying on the wind for blast. Next came, either the hearth about 12 in. in diameter by 2 ft. in height, blown by a man operating two goat-skins for bellows, or, a hearth of greatly varying diameter and about 10 ft. high, depending for its blast upon natural draft. The former appeared in India, the latter in Burmah; and both were in operation until quite recently, though their origin is lost in prehistoric times. The Catalan forge was the evolutionary descendant of the foregoing, and the parent of the Blase-ofen, which in turn led to the high bloomary or " Stückofen," the father of the blast-furnace, as a producer of cast-iron. The production of cast-iron checked the growth of the direct processes; and led to the introduction of various hearths, such as the Walloon, for low-silicon irons; and the South Wales process, combining the run-out fire with the finery, for higher-silicon irons. Some of these are still in operation in localities possessing the necessary raw materials; and their product is used for purposes requiring wrought-iron of exceptional quality, the supply of which is still smaller than the demand. We have to look back but a century and a quarter to see the introduction of the puddling process by Henry Cort; a process which, reinforced by the iron-oxide bottoms and fettling of Hall, was not less revolutionary in character, and more revo-

Jul 1, 1905

By R Durchholz, A-J Heiertz, R Schmitz

Mining of lignite is the largest bulk materials handling activity in Europe. In order to mine this lignite, with an average calorific value of only a third of bituminous coal in an economical way, highly efficient opencast mining technology is mandatory. The total continuous mining of overburden and lignite was introduced more than 60 years ago and was subsequently developed stepwise into the largest mass transport system of the world. In 2011, the Inden Mine, one of three RWE Power mines, stripped 90 Mbcm of overburden to produce 22 Mt of lignite. In total, nearly 100 Mt of Lignite was produced from the three mines of RWE Power in Germany. Beside bucket wheel excavators (BWE), several high-performance in-pit crushing and conveying (IPCC) systems, which allow the adoption of continuous mining systems, even for typical shovel and truck (S&T) operations, are available today. RWE Power assists operators considering a change from the S&T to IPCC technology, both in the planning process involving large-scale belt conveyor systems and later with operational know how transfer. In a number of cases, the challenges associated with this system change have been addressed and solved successfully. One key challenge is managing the development of skills for operating the belt conveyor systems efficiently. This paper compares the effectiveness of S&T to different configurations of continuous mining operation for an up to 170 m deep mine with a total annual output of 117 Mbcm. From the mine operatorÆs point-of-view, the quantity and skill level of staffing required for operation and maintenance are discussed in detail. The main conclusion of this paper is the larger the operation becomes and the longer the mine life is, the earlier fully continuous mining systems should be planned and implemented.CITATION:Schmitz, R, Durchholz, R and Heiertz, A-J, 2012. Change challenges for large open pit mines, in Proceedings Eighth Open Pit OperatorsÆ Conference , pp 103-110 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 18, 2012

By A. Mukhopadhyay

Gas stirring, simultaneous arcing, chemical additions are some basic steps in the secondary steel making. From tap to team however, there are enough uncertainties and several in-situ decision making required to match the fmal composition and temperature in the given amount of processing time. Currently available control algorithms rely on overall material and heat balance coupled with a self-learning regression based tuning of model constants. In this paper we demonstrate the capabilities of Computational Fluid Dynamics (CFD) in modeling and analyzing the thermo-chemical aspects of secondary Steelmaking. These models take advantage of scientific and engineering advances in computational tools and provide almost real time speed of analysis. This can be a very effective tool for operator training, process debugging and improvement as well as new innovations. Keywords: Argon purging, Secondary steelmaking, Arcing, Ladle Furnace, Process Control.

Jan 1, 2003

By J. Ouellet

The design of hydrostatic liner for a deep potash mine shaft in Saskatchewan poses tremendous technological challenges. Technology has evolved to a point where one could consider a new innovative approach to hydrostatic liner design. But there is still a place for conventional technologies such as cast iron tubbings. As will be discussed in this paper, improvement to manufacturing process, installation procedures and even new materials can bring this technology to an excellent level of performance. With the spur of new projects in the potash industry of Saskatchewan, the authors worked in various shaft liner designs from the conceptual stage through to the construction phase. They were either directly leading the design work on some of these projects or acting as an external reviewer on others. Most of these shaft liner designs involved cast iron tubbing technology and ground freezing. The major challenge in sinking potash shafts in Saskatchewan is to go through a water-bearing ground formation under high pressure, known as the Blairmore or Manville fm. The only proven stabilizing technology for these formations is ground freezing. For a potash shaft, dry shaft conditions are highly desired, so a fully waterproof hydrostatic liner is required. All the existing potash mine shafts in Saskatchewan, except for two with composite steelconcrete lining, used the cast iron tubbing technology. Two new shaft tubbing liners have been constructed recently, one in the Athabasca Basin and one for a potash mine in Saskatchewan. When the authors began working on these new projects, what became quickly evident is that the technological knowhow for designing and constructing tubbing liners was no longer available within Canada and that the past construction methods used to sink tubbing lined shafts was obsolete. The tubbing liner for the shafts sunk in the sixties were designed either by German or British companies. In both of these countries only few tubbing lined shafts were sunk in last 40 years and the technology used in the sixties was not improved. There are only few countries where tubbing is routinely produced and installed: China, Russia, Ukraine and Poland. Out of these countries Poland is the one where this technology is the most advanced. The authors, working in close collaboration with engineers from Poland, attempted to rebuild this knowledge for the mining industry in Canada. This process involved thorough analysis of old technical reports, literature review and study of current polish design and construction practices as well as site visits of existing shafts. Through actual construction experience, some lessons were learned as well as ideas for improvements. In this paper, the authors will present a succinct review of design and procurement process. But, the practical aspects of the construction and installation methodology will be treated with more emphasis, more specifically the practice leading to good liner performance. Some of the poorly understood technical aspects of tubbing installation will be discussed more thoroughly and some currently accepted myths dispelled.

Aug 1, 2013

By W. J. Kempson

In recent years, substantial progress has been made with respect to the definition and control of the primary energy requirements in underground mines. Little has, however been done to develop a more detailed understanding of how to limit the various pressure losses which are intrinsic to shaft systems. This is in spite of the fact that more than half of the pressures generated by the ventilation fans in deep level mines are dissipated as pressure losses within the shaft system. This paper presents research which has been completed to optimise the pressure losses which occur in shaft systems as a result of the ventilation air flowing through them. In this regard, the response of various shafts to the ventilation air flowing through them was measured. These results were evaluated against the current theory for the calculation of shaft pressure losses. Finally the results of the measurements and calculations were used to calibrate a Computational Fluid Dynamics model of the shaft systems. This model was then iterated to allow meaningful conclusions as to the specific make up of the shaft equipment which contributes the most to pressure losses in shaft The results of the above analysis demonstrated that the current theory used for the evaluation of these pressure losses is deficient. The paper discusses these conclusions and the specific ramifications of the analysis. Finally, the understandings gained with regards to the above research are applied to the design and layout of equipment in mine shafts. In this regard, the shape and orientation of the shaft steelwork is evaluated and it specific interaction with the piping and conveyance is evaluated. Coming out of this evaluation are specific recommendations for the design of future shaft systems. These recommendations are based on the above models and offer specific savings on the lifetime operating costs of shaft systems.

Aug 1, 2013

By L Mottola

Three decades ago mining companies, principally in North America, aided by machine and explosive manufacturers, started significant attempts to develop and implement automated mining systems, mainly underground. These tended to be motivated by decreasing cost, increasing productivity, reducing labour requirements, and improving safety. These are important business drivers, however, little attention was given to the underlying goal of mining automation, namely to bring upstream processes in control and reducing variation, as seen in downstream mineral processing plants.This paper first reviews the nature of Lean Thinking and its application in the context of the growing commitments by industry to develop future automated mine production systems. The paper then makes reference to prior and current experiences in open pit blasthole drill and shovel performance monitoring, to demonstrate the principle that machine performance data offers as a means, not only to characterise the dynamic geological and working environment, but also to provide a foundation for automation. In this case, drill and shovel monitoring was originally motivated as a means to optimise blast fragmentation through more effective drill and blast designs that are based on an accurate determination of the bench geological and geotechnical characteristics, hence managing variation in the drilling and blasting process. This paper considers how automating and integrating such components of the mine production system would bring processes into a controlled state, creating value at the face, within a framework of Lean mining.

Nov 22, 2011

By K. A. Natarajan

"Interaction with microorganisms results in significant surface chemical changes on minerals. For example, chemolithotrophs such as Thiobacillus ferrooxidans and Thiobacillus thiooxidans significantly alter the surface chemistry of several sulfide minerals such as pyrite, chalcopyrite, sphalerite and galena. Heterotrophic bacteria such as Bacillus sp. could alter the electrokinetic properties of oxide minerals such as hematite, alumina, silica, kaolinite and calcite. Microbe-mineral interactions could thus be beneficially utilised in mineral beneficiation as different from bioleaching. Microbially induced mineral beneficiation unlike bioleaching deals with interfacial phenomena at mineral-solution-bacteria interfaces and surface chemical changes are brought about at very rapid rates amounting to a few minutes resulting in mineral separations in an aqueous medium.In this paper, the role of acidophilic chemolithotrophs such as Thiobacillus thiooxidans and neutrophilic heterotrophs such as Bacillus polymyxa in the beneficiation of sulfide and oxide minerals is illustrated. Mechanisms of bacterial attachment on various sulfide and oxide minerals are outlined with respect to the influence of bacterial interaction in bringing about mineral surface hydrophobicity or hydrophilicity. The role of bacterial cells as well as metabolic products such as bioproteins and exopolysaccharides in significantly altering the surface chemistry of sulfide minerals such as sphalerite and galena and oxides such as hematite, alumina, silica and calcite is discussed with probable mechanisms. Possibilities of generating mineralspecific bioreagents are outlined with respect to bacterial adaptation to mineral substrates."

Jan 1, 2003

By L. M. Oshinowo

The incorporation of advanced analysis tools, such as CFD, into the process plant design process has become possible through advances in commercially available computational fluid dynamics software and faster computers. Multiphase modeling is now typically employed in the design phase of process plant design at Hatch. The multiphase models include Lagrange-Euler and Euler-Euler treatment of the multiple phases. Additionally, mixture models with interface-sharpening algorithms are applied to the prediction of free-surface flows in complex geometry. CFD is applied to applications where traditional design rules are not applicable. The additional rigor of CFD modeling in 2D and 3D allows process engineers to come closer to realizing true virtual plant design. The objective of this paper is to outline the benefits and pitfalls in the application of multiphase modeling for rigorous design. Several application examples in the hydrometallurgical field will be presented.

Jan 1, 2005

By Stephen C. Tadolini, John P. McDonnell

"High-strength cable bolts have been used for ground support in underground coal mines for many years. Cable bolts are routinely used as secondary ground support in numerous longwall gateroad support applications, areas that possibly experience the most severe conditions in current underground coal mining. Additionally, when mining ground conditions deteriorate, engineers oftentimes recommend cable supports as a principal solution because of the established credibility for successful ground control. Nevertheless, there is still a reluctance to utilize non-tensioned cable supports as an effective primary roof support alternative.This paper provides historical and recently documented examples of non-tensioned cable supports utilized as an effective primary ground support method in a western U.S. underground coal mine, and it will continue the technical discussion between the differences of various degrees of tension in cable supports with respect to ground behavior and reactions.INTRODUCTIONResin-grouted cable supports are widely used to support difficult ground conditions throughout the world. Through the use of innovative applications and configurations they have proven to be a major paradigm shift in roof support and ground control technology in the U.S. (Tadolini and Koch, 1993; McDonnell et al., 1995; Tadolini and Gallagher, 1994; Tadolini and Trackemas, 1994)Today, the basic cable bolt support consists of a high-strength steel cable installed in bore holes that range in diameter from 25 to 50 mm (1 to 2 in) depending on the strand size and drilling equipment. Cables are offered in both bright and galvanized, for corrosion protection, and range in capacity from about 30 to 60 tons. An example of a resin-grouted cable bolt and the key components is shown in Figure 1. The steel cables are flexible and the support length is not limited by the height of the opening. Lengths of up to 10 m (32 ft) have been supported with high pattern densities when standing supports were not operationally feasible. The most common lengths are 3 to 5 m (10 to 16 ft). An important physical characteristic is that PC-strand has an ASTM minimum elongation requirement of 4%. For comparison purposes, the ASTM 432-08 Standard Specifications for Roof and Rock Bolts and Accessories specifies elongation requirements for traditional roof bolts are a minimum of 12% for grade 40, 9% for grade 60, and 8% for grade 75 materials, respectively. Traditional roof bolts can stretch and elongate twice the length that cable bolts can, which makes design considerations challenging."

Jan 1, 2010

"Conveyed coal flows have been diverted on the basis of real time ash analysis since the 1980s. Many coarse particle separation methods are available through screens, jigs, heavy media separation, particle sorters, to name a few, however bulk diversion requires a representative, continuous analysis to ensure diversion decisions can be made with confidence. Sensors also need to be able to provide measurements at useful time increments so that small tonnages can be diverted for maximum selectivity. Particle separation typically requires high capital costs and there are limitations either in throughput tonnage or particle size or both. Few techniques are able to provide robust and representative analysis of conveyed flows in a useful time basis. Prompt Gamma Neutron Activation Analysis provides multi-elemental analysis of conveyed bulk materials and has been proven in the minerals industry since 2003. This paper outlines the success of this technology in minerals applications in iron ore, phosphate rock and most recently in copper-gold ores, including its use in bulk diversion.INTRODUCTION Naturally occurring quality variability, or heterogeneity, in mineral deposits enables separation and recovery of the valuable components through mining and processing operations. There are distinct advantages in processing the minimum quantity of material to achieve the highest possible yield. Unfortunately, declining ore grades has resulted in larger scale operations and a subsequent loss in selectivity for mining operations. As limits are approached on the practical size of equipment, there is more motivation to investigate alternative solutions. Mining companies are subject to increasing social resistance to growing waste disposal requirements in addition to higher energy and transport costs. Major savings are available by reducing the quantities of material processed where pre-concentration can be effectively applied at early stages in the process. One of the simplest ways to pre-concentrate is to measure the bulk material and reject waste soon after mining so that minimal expense is incurred and that only higher quality material is sent to processing operations. This bulk sorting can occur within the mining operations and has major benefits through energy and other consumables savings. This paper discusses the application of real time analysis technologies suitable for bulk sorting within the minerals industry. Technology that has proven representative for conveyed material bulk analysis and its successful applications to date is explained. Analysis using a sensing technique is only one component of a successful bulk sorting process; the importance of effective diversion systems and a bulk sorting strategy are also discussed. The bulk sorting stage may be one component of a system that could include additional downstream technologies such as particle based sorting systems on a diverted stream."

Jan 1, 2018

By S. N. Kalyakin, D. S. Flett, M. A. Mulagaleeva, N. V. Gudkova, S. S. Serdyuk, V. I. Kuzmin, Institute of Chemistry and Chemical Technology SB RAS, O. A. Logutenko, V. N. Kuzmina, V. G. Lomayev

"The Chuktukon niobium-rare earth elements ore deposit is located in Siberia (Russia). Weathered carbonatite crusts are the basis of the ore deposit. The deposit itself is 3.5 km in length, about 800 to 1400 m in width and up to 200–300 m in thickness. The ores are composed of iron-manganese oxides (hydrogoethite, hematite, psilomelane, pyrolusite) and contain 3–7% of rare-earth phosphates (florencite, monazite) and 0.5–1% of niobium oxide (pyrochlore). The ore is completely finely dispersed and consists of oxide particles formed of compact, dense aggregates which makes ore dressing as well as leaching of the rare and radioactive elements very difficult. Several options for processing of these ores have been considered: 1) reduction of the iron oxides to magnetite followed by beneficiation with magnetic separation to produce a rare metal concentrate; 2) processing of the rare earth elements (REE) containing minerals by direct alkaline-acid treatment; 3) processing of the ores using nitric acid leaching in an autoclave.INTRODUCTIONThe Chuktukon niobium-rare earth metal ore deposit is located in Siberia, in the Krasnoyarsk region, 110 km from the Boguchan hydroelectric power station which has recently been commissioned. This mineral raw materials is capable of providing impetus for the modernization of the Russian rare metal industry because of its qualitative and quantitative characteristics. The deposit is located in a region of promising industrial development and is a part of the territoriy where the Russian Federation’s Program “Complex Development of the Lower Angara Region” is currenly being realized. The main program directions are creation and development of industrial activities in sectors such as power, metallurgy, oil and gas, gold, rare-metals, and timber. The program will aid the development of the niobium and rare-metal resources of the Lower Angara and neighbouring regions as well as increase the national production of REE and therefore import substitution (Lapin, 1997; Lomaev & Kuzmin, 2003; Lomaev & Serdyuk, 2011; Serdyuk, Lomaev, & Kontorovich, 2000)."

Jan 1, 2016

By J Miedecke

A metalliferous mine has operated at Storys Creek from the 1890s to 1979. Storys Creek drains from a pristine catchment and National Park and remains as the most degraded stream from historic mining in north-eastern Tasmania. It has been the subject of public concern since the closure, particularly at times of high rainfall such as existed in 1985 and 1986. The mine is located on the banks of the creek, which flows into a major river, the South Esk River, which is one of TasmaniaÆs largest rivers and important for recreational fishing and water supplies. For much of the life of the of the operations tailings were directly discharged into the creek, and in latter years stockpiled or very close to it. Little rehabilitation was carried out at mine closure. The result was erosion and subsequent deposition on the banks of the creek downstream. Direct emissions of adit water and the consequential emission of contaminated ground water to the creek continue to affect water quality. Contaminant loads discharging from the mine and tailings comprise 70% of the metal load in the catchment and are by far the largest single source. Acidity data suggested that the introduction of systems to introduce alkalinity could be effective in ameliorating the residual acid drainage impacts in the Storys Creek catchment. After a period of investigations and trials which proved their effectiveness, treatments adopted have included the following: relocation of tailings to a constructed and clay capped disposal area and rehabilitation of tailings area; crushed limestone addition to stream flows; crushed limestone addition to creek banks and exposed tailings; sealing of a drainage Adit; and construction of an anoxic drain to generate alkalinity to surface waters draining to old mine workings. These innovative treatments have resulted in a marked improvement in water quality draining from the area. The anoxic drain is believed to be one of the few, if any, which has been constructed to have generated high levels of alkalinity from clean waters and offers a solution to the clogging problems experienced in such drains in the past. Similarly, the use of crushed limestone in an active stream has proved effective in buffering acid drainage and removing metals from solution.

Jan 1, 2003

The Mt Lyell Mine at Queenstown, Tasmania was re-opened in 1995 by Copper Mines of Tasmania Pty Ltd, a wholly owned subsidiary of Mt Lyell Mining Co Ltd. The re-opening followed over 100 years of copper and gold mining at Mt Lyell. Major changes in practice were implemented across the site. Preventing further damage to an already disturbed environment was a major priority. Sublevel caving, at a lower cut-off grade, replaced open stoping for the deep underground mining. Development and later stoping are handled by a contractor, National Mine Management Pty Ltd, in the largest underground contract awarded at the time. Large scale sublevel caving was new to Mt Lyell and not widely practised in Australia, requiring studies and systematic development of the method, particularly in drilling and blasting. Rehabilitation and upgrading of mine infrastructure have been and will continue to be a challenge. The mine has, since 1995, returned to being a stable producer with potential for growth.

Jan 1, 1998

By B McFadzean, N P. Lima, D A. Deglon

The reverse flotation of Itabirite iron ore is typically performed after a desliming step in which most of the sub-10 µm particles are removed. This is done to limit processing problems such as poor flotation recovery of SiO2 due to slime coatings and increased slurry viscosities, unmanageable froths and increased losses of hematite particles due to entrainment. However, the rejection of ultrafine particles contributes to large losses in iron recovery and may contribute to the instability of tailings dams. The aim of this study is to decouple the effects of ultrafine particles in the pulp and froth phases to better understand the processing capabilities of the fines fraction. The flotation test work was performed in a special-purpose continuously operated laboratory flotation cell that has a deep froth section to simulate plant-scale froth conditions. Five conditions of fines addition were investigated at three different froth heights and a solids concentration of 50 per cent. The behaviour of the pulp and the froth were decoupled using froth stability and froth recovery tests. This showed that, even though there is an exponential increase in froth stability at increasing fines quantities, the performance of the pulp has the overriding effect on the overall SiO2 recovery. Pulp zone, froth zone and overall SiO2 recoveries showed that overall recoveries increased by about 3.6 per cent for every 1 per cent decrease in fines content. This meant a large increase of 20 per cent in SiO2 recovery when going from undeslimed to deslimed feed. This was driven largely by increases in the pulp zone recoveries, which were about 4 per cent for every 1 per cent decrease in fines content. The froth recoveries, on the other hand, decreased by between 0.75 per cent and 2.5 per cent for every 1 per cent decrease in fines content, depending on froth height. This paper explores further insights into iron ore flotation processing at different slimes concentrations.

Aug 24, 2022

By Anatoly Usov

The detailed researches of a broad circle of problems connected to development of the electric pulse method destruction materials (EPD) of a various nature and area of use are executed. The electrical and power characteristics of process, physical fundamentals of selectivity of a breakdown and destruction are investigated, the device of electric pulse (EP) disaggregation and ?omminution of materials are developed, the technological efficiency of disintegration of industrial minerals estimated. Due to its technological advantages, the EPD could have a great potential in minerals mining and processing technologies. Low specific power and weight-and-size characteristics of EP installations based on the existing out-of-date electric equipment are at present the main reasons hindering the effective application of the method in mining and processing technologies. The main studies carried out in Russia in the field of electro technical equipment development for EP technology are presented. The pulse capacitors service life affects greatly the economic efficiency of the process because the capacitors cost accounts for a considerable, and in some cases, the most part of the operational costs. Determined and analyzed in the study are the ways which could significantly improve the specific characteristics of high voltage pulse generators (VPG), such as to use of high-frequency voltage transformation to develop a charger; to use pulse transformers (PT) with iron magnetic circuits made of materials characterized by high magnetic permeability, in pulse generating circuits; as well as to use special ways which could produce voltage pulses with a short front. The experiments have proved the possibility to adapt these technological solutions for EP devices, and a further strategy of the EP technologies development and application has been suggested on this base. Keywords: electric pulse disaggregation, electric pulse installation, charger battery, high voltage pulse generator

Sep 1, 2012

By Sathit Tandanand

This Bureau of Mines report describes the method of obtaining a strength index for rock drillability, particularly for percussion drills. The original Protodyakonov method has been slightly modified, essentially to eliminate uncertainties in the measurement of the volume of fines, and to avoid conjecture in selecting the representative value as the strength coefficient. A theoretical consideration of the relevant parameters in the method was extended from a comminution theory, and hence the meaningful value was obtained experimentally by plotting the ratio of the number of drops and the volume of fines against the number of drops. The minimum ratio of the number of drops to the volume of fines in the plot was selected as the coefficient of rock strength. The modified method of obtaining the strength coefficient preserves the original Protodyakonov test apparatus and the merit of simplicity of the test procedure. The modified coefficient of rock strength shows its usefulness in predicting penetration rates with greater reliability than other mechanical properties. Consequently, the drillability curves were drawn using the modified coefficient of rock strength as the parameter for penetration rate prediction in the field.

Jan 1, 1975

By X. Xu, J. K. -W. Wong, J. -Y. Delenne, K. Soga

Hydraulic fracturing (HF) is a mulit-scale and multi-physics process which makes numerical modelling challenging. Conventional numerical models focus on multi-physics nature of HF but the multiscale nature is compromised by idealization of reservoir to be continuous, homogeneous and isotropic. However, natural fractures take a significant role in the success of HF for exploration of unconventional resources like Shale gas. Advancement in microseismic monitoring provides useful data for simulation in a much greater details. There is an urgent need to develop a suitable numerical tool for multi-scale threedimensional simulation to better understand the roles of discontinuities and heterogeneity in reservoir and its interaction with HF, especially to address the environmental concerns such as induced seismicity. In this paper, a simple discontinuum numerical method – Lattice Element Method (LEM) is proposed to model HF in a large scale three-dimensional model. A reservoir is modelled as a lattice network composed of 1D Hookean’s spring. Fracturing is modelled simply by removing lattices that meet a specified threshold as determined by the critical energy release rate of the rock. By introducing disorder in the model, mesh dependency in modelling fracture growth is minimized. Fluid flow is simplified as flow in pipe network and the permeability of pipe is related to fracture aperture by cubic flow law. Therefore, fracture flow and rock deformation are fully coupled. In this paper, four simulations of the same configuration except with different degrees of reservoir heterogeneity are presented. Fractures formed are diffusive and two groups of fracture are identified – connected fractures and isolated fracture without clear spatial correlation. The former forms a ‘fracture cloud’ and contributes to fluid flow and modeled by pipe network. The flow of fluid is highly tortuous and pipe network is sparely connected. The degree of reservoir heterogeneity controls the growth of ‘fracture cloud’ and pipe network. Microseismic monitoring often shows diffusive fracturing during HF on site and hence the outcome of the proposed model can be compared to such monitoring results.

Jan 1, 2015

By R. J. Heemstra

A continuous flowing paper electrophoresis cell was used to separate petroleum and petroleum extracts into characteristic patterns. The electrophoresis of Bachaquero, Lagunillas, Boscan, and Gibson petroleums in nitro-benzene and acetic acid-based electrolytes was investigated. The extent of separation in the patterns was studied by measuring the metal and porphyrin contents of the effluents. Qualitative separations were achieved in some systems, whereas either system demonstrated only a high degree of electrophoretic migration.

Jan 1, 1967