Search Documents

By C. R. McCann

The Bureau of Mines conducted an experimental study of conditions needed to produce flames of pulverized coal when the heat needed for ignition is sup-plied only from the flame and hot furnace refractory. An electrically heated furnace which burned about 1 pound of coal per hour was designed and fabricated. A sheath of air, surrounding the primary coal and air stream, was used to prevent entry of hot gases from recirculating combustion products. Furnace temperatures needed for ignition ranged from about 1,8300 F for an Illinois coal to 2,250° F for a Beckley seam coal. Apparent flame velocities were about 2 to 5 feet per second, increasing with volatile content of the coal and with distance from the burner mouth to the flame. The time required for ignition, approximately 0.02 to 0.07 sec, was a better measure of flame behavior than was velocity.

Jan 1, 1969

By M. Louarrat, G. Enaime, A. Yaacoubi, A. Baçaoui, J. Blin

"The purpose of this study is to prepare a new activated carbon from olive stones for use in gold recovery by carbon-in-leach (CIL) and carbon-inpulp (CIP). The preparation method chosen was physical activation using steam. The effect of four process parameters: the residence time for carbonization, the activation temperature, the residence time for activation, and steam flow, were studied by the mean of response surface method (RSM) in order to optimize the yield, iodine index, and attrition characteristics. These two last responses were used as primary indicators of gold recovery capacity and mechanical strength. The results obtained show that optimal activated carbon can be prepared under the following conditions: a carbonization time of 157 minutes, activation at 921°C for 53 minutes, and a water vapour flow of 0.18 mL/min. This optimum carbon has an iodine value greater than 1100 mg/g and an attrition index in the order of 0.74%. These values reflect the quality of the precursor (olive stones) as a raw material for the development of an effective new activated carbon for the gold mining industry. IntroductionActivated carbon is an effective adsorbent widely used in industry due to its high surface area, well-developed reproducible microporous structure, and high degree of surface reactivity and adsorption capacity. World consumption of activated carbon is steadily increasing. It is primarily used in industrial wastewater and gas treatment and also for silver and gold recovery from cyanide solutions (Syna and Valix, 2003; Soleimani and Kaghazchi, 2008; Buah and Williams, 2010; Eddy et al., 2011). However, activated carbon is expensive and it needs to be regenerated after each adsorption cycle. In order to decrease the cost of manufacturing activated carbon, low-cost forest and agricultural wastes are considered promising new materials. In recent years considerable research has been reported on activated carbon from agricultural wastes, such as olive stones (Yavu et al., 2010), acorn shells (Sahin and Saka, 2013), peanut shells (Wu, Guo, and Fu, 2013), grape seeds (Jimenez-Cordero, 2014), coconut shells (Yalcin and Arol, 2002; Gratuito, 2008), palm shells (Sumathi, 2009), cherry stones (Jaramilloa, Gomez-Serrano, and A´lvareza, 2009), macadamia nut shells (Eddy, 2011), apricot stones (Soleimani and Kaghazchi, 2008), and bagass (Syna and Valix, 2003)."

Mar 1, 2019

By Gary L. Stecklein

This final report delineates the findings of the test programs, simulations, and analyses performed to determine the requirements for the effective application of berms and guardrails as truck restraint systems for elevated mine roadways. Included arts criterion for effective vehicle restraint for guardrail applications and recommendations for berm applications based on scale model tests and computer simulations. Full scale haulage vehicle-berm interaction field tests were performed to correlate the results of these model tests and computer simulations. Recommendations for the construction of berms were made on the basis of tests of berm bearing strength, response of the vehicle to different berms, and predictions based on the obtained correlation

Jan 1, 1981

By R. A. Guereco

Accurate measurements of physical dimensions of a section of stainless steel capillary tubing are presented and used to develop two final working equations for an absolute gas viscosimeter. The effects of pressure and temperature on these dimensions are considered. The internal surface finish and nonuniformity of the capillary bore are discussed, as well as entrance, kinetic energy, gas slippage, and gas compressibility correction factors.

Jan 1, 1967

By J. -C. Parisien-La Salle, D. Blais, G. P. Demopoulos

"In this work the dissolution, precipitation and adsorption behaviour of gold in acidic iron sulphate media containing small amounts of chloride ions is investigated via batch laboratory tests and OLI thermodynamic calculations over the temperature range 25-250°C. Chloride ions may be present in industrial pressure oxidation/pressure leaching (POX/PL) operations due to elevated water salinity levels or due to intentional addition as is the case of the CESL Copper Pressure Leaching Process. Thermodynamic calculations show that AuCl4 - may form depending on the free Cl-/Au ratio and temperature, its stability increasing with increasing Cl- concentration and decreasing with increasing temperature. On the other hand during POX/PL, we know that massive precipitation of iron in various hydrolysis products and compounds occurs. Hence of interest is the question how AuCl4 - that may form during leaching interacts with the iron precipitation products. Gold(III) chloride was found to co-precipitate with iron(III) (oxy) hydroxides and arsenates forming in the autoclave but not with natrojarosite. Upon further investigation it was discovered that activated carbon added in the autoclave (as done in CIL) acts as preferential sink for the mobilized gold, hence opening the potential for the development of a direct cyanide-free gold recovery process in acidic sulphate leach reactors.INTRODUCTIONThe recovery of gold from ores and concentrates has evolved over the years with processing routes becoming increasingly complex. Given the high value of gold, any reduction in losses during recovery operations constitutes an important economic benefit. One such loss that needs to be addressed is the potential solubilisation of gold during pressure oxidation (POX) of refractory sulphidic gold feedstocks. For example, Agnico Eagle Mines reported a loss in gold recovery due to the formation of a gold chloride complex (Garofalo, 2009). Gold is known to form complexes in solution, such as gold(III) chloride, if an excess of chloride ions are present. The fate of such soluble gold chloride during pressure oxidation and the subsequent neutralization of the acidic discharge slurry will determine if gold is lost or recovered in the downstream cyanidation operation. Thus it is of interest to know under what conditions gold chloride may stay soluble or co-precipitate along primary (formed in the autoclave) or secondary (formed during neutralization) precipitates. Furthermore, the mode of co-precipitated gold, such as adsorption on iron compounds, like goethite and hematite (Machesky et al., 1990; Nachayev, 1984); substitution in one of the precipitated phases; or finally chemical reduction to metallic state would have consequences in terms of gold recovery."

Jan 1, 2012

By D. Duff, R. A. Cameron, R. E. S. Whitehead

"Although CO2 content indicates the quantity of carbonate in altered basaltic rocks, it does not measure the intensity of carbonate alteration. CO/CaO molar ratios, which correlate with the relative proportions of individual carbonate species, measure the intensity of carbonatization. The Timmins gold area is characterized by pervasive carbonatization, with large parts of the area having CO2/Ca0 ratios greater than 1, representing C02 supersaturation relative to CaO. The mean CO/CaO in the Timmins area is0.67, compared to 0.13 in two unmineralized control areas. Regional arsenic abundance in the gold-bearing area averages 4 ppm, compared to about 0.35 ppm for the non-mineralized areas. The average K20 and Rb abundances are similar in both mineralized and non-mineralized areas (about 0.30% K20 and 7 ppm Rb). Although there appears to have been no wholesale addition of K20 or Rb to the mineralized area from external sources, these alkalies have been redistributed internally, resulting in patterns of local enrichments and depletions which are characteristic of the mineralized region.Local target anomalies associated with known mineralization consist of CO2/Ca0 > 1.5, As > 10 ppm and K2O > 0. 75%. Not all three values are required to be above these thresholds in order to identify local targets. Combinations such as C02/ Ca0 > 1.5 and As < 10 ppm, CO/CaO 1-1.5 and K20 > 0. 75 or K20 > 0. 75 and As > 10 ppm are equally indicative of proximity to gold occurrences. Gold-bearing veins and associated anomalies occur throughout the entire volcanic succession and are not restricted to any particular stratigraphic horizons. The levels and patterns of alteration and occurrences of gold appear to be structurally controlled."

Jan 1, 1982

By H. P. Greenwald

About mid-December 1936, the safety director of a large coal corporation visited the authors at the Bureau&apos;s Experimental coal mine to discuss a rock-dust barrier he had invented primarily for use in trackless entries of coal mines. The rock dust in this device was carried in its original paper containers and means were provided for ripping these open so that the dust might be scattered in the path of an explosion. The inventor termed the device a "bag barrier", and this term has been adopted in the present paper for convenience. At that time the device was in an early stage of development, and the inventor felt that the barrier should be tested to determine whether it had enough promise of being successful to justify further development. The matter was taken under consideration and finally three tests were made during the week of February 15, 1937. It was concluded that while the device did stop an explosion in two of the three tests, it was much loss effective than ordinary rock dusting, and that too few data were obtained to permit direct comparison with tests of other barriers. Apparently, the conditions under which the device could, be successful were somewhat limited, out the limits could not be defined without additional tests.

Jan 1, 1938

By S. H. Ash

The paramount responsibility of Government is to protect the general welfare. One of the chief functions of the Bureau of Mines is to investigate and publicize methods of increasing safety and efficiency in mining operations. In an industrial civilization, energy resources constitute the foundation of a sound economic structure (14).4/ Coal is only one source of energy, but it provides more than half the energy consumed in the United States.

Jan 1, 1946

By A. C. Johnson

This circular is one of a series published by the Bureau of Mines describing mining and beneficiation methods and costs at various mining operations throughout the United States. Inclusion of the Abbott mine in this series is of particular interest, as the complex geology and the character of the deposits make their exploitation a unique operation. The mine operates on a high-cost, comparatively small-scale basis, and only the persistence of an aggressive management has enabled it to maintain its rank among the major mercury producers of California. Rising costs and decreasing metal prices, which continuously threaten the low profit margin, are reflected in increased efficiency of operation. This report summarizes past operations and describes, in detail, the geology and ore deposits; exploration and mining methods; and furnacing and condensing operations. It covers the entire operation from initial exploration to the actual production of mercury. Comparative production costs for 1944 and 1958 are of special interest.

Jan 1, 1962

By M. Sears, K. Mohamed, J. Addis, J. Wickline, G. Rashed

To better understand the load shedding and the stress transfer on coal pillars due to room-and- pillar retreat mining in deep cover panels, researchers from the National Institute for Occupational Safety and Health (NIOSH) conducted a monitoring field study. Two sites, at overburden depths of 1,000 ft (304.8 m) and 1,500 ft (457.3 m), were selected in a room-and-pillar mine operating in Southern West Virginia. The deformation and stress changes in the roof and two adjacent pillars at each site were monitored during the retreat mining process. The monitoring results and field observations were used to calibrate large-scale FLAC3D models for each site. The calibrated models were used to assess different sizes of roof bolts installed in deep cover areas. INTRODUCTION Deep cover room-and-pillar retreat mining is an important emerging issue that will intensify in the future as shallower reserves are depleted (Mark, 2009; Chase et al., 2002). During pillar retreat mining, the likelihood of local and/or global instabilities increases due to elevated stress levels near the pillar line because of the abutment loading. In the last decade, approximately 31% of the room-and-pillar mining groundfall fatalities in the United States occurred during pillar retreat mining. Between 2013 and 2017, this proportion increased to 55%, of which 50% of these fatalities were due to falls of roof and rib that occurred during pillar recovery (MSHA, 2018). One interesting piece of information about pillar recovery fatalities was that the victim was nearly always under bolted roof. Sheared and broken #5 (5/8-in), fully grouted rebar bolt failure contributed to three of four fatal roof fall incidents that have occurred in deep cover retreat mines (NIOSH, 2010). This claim raised the following question at the study mine: Is it safe to use a 4-ft long #5 (5/8-in) rebar bolt grade 60 at a depth of cover more than 1,000 ft (304.8 m)? There was some concern about shear failure of the #5 (5/8-in) rebar bolt at a depth of cover over 1,000 ft (304.8 m). To answer the question and to reduce accidents and fatalities caused by ground falls due to room-and-pillar retreat mining in deep cover panels, the National Institute for Occupational Safety and Health (NIOSH) monitored the roof and rib deformation and the change in vertical pressure within two adjacent pillars during pillar recovery. The study was conducted at two deep cover sites in a room-and-pillar mine located in Southern West Virginia that operates in the Lower War Eagle (LWE) seam. The monitored sites were selected at 1,000 ft (304.8 m) and 1,500 ft (457.3 m) depths of cover. In this paper, site-1 represents the monitored site at 1,000 ft (304.8 m) of cover, while site-2 represents the monitored site at 1,500 ft (457.3 m) of cover. For this study, large-scale FLAC3D numerical models were calibrated based on both field observations and instrumentation results. The calibrated models were then used to compare the ground response and the induced stresses of two pillars at instrumented sites 1 and 2. The maximum lateral displacement (roof shift) obtained from the calibrated large-scale FLAC3D models was applied to a small-scale FLAC3D bolted models, the safety factor for axial stresses of the simulated roof bolts was calculated at the deep cover sites.

Jan 1, 2019

By Nilufer Kursunoglu

Despite being crucial for meeting the world’s energy demands, coal mining operations present considerable health risks, especially when it comes to exposure to coal dust. Longwall coal mining, an advanced technique, has considerably enhanced production but made dust control more difficult. Due to its explosive nature, coal dust continues to be a serious and dangerous concern in the industry despite developments in safety technology. This study aims to comprehensively assess the risk of coal dust explosions by integrating fuzzy risk matrix and Pareto analysis methodologies, offering precise risk ratings for various root causes. A fuzzy risk matrix was developed to assign exact risk ratings to identified root causes. Additionally, a Pareto chart was used to identify the main reasons and suggest particular preventive measures. 17 significant causes were determined for underground coal mines based on the study’s methodology, and some preventive measures were suggested. In accordance with fuzzy risk rating values, root causes were divided into six categories. The root hazard with the highest risk rating was identified as ‘accumulation of inflammable gas/gases’. The proposed approach was used to examine incidents caused by coal dust explosions in Turkish coal mines in order to demonstrate the effectiveness of combining the fuzzy risk matrix and Pareto analysis for assessing coal dust explosions. This study gives not only a solid framework for risk assessment but also critical information for classifying the risks associated with coal mine dust explosions. The results highlight the critical necessity for proactive and preventive actions to reduce the hazards of coal dust explosions and protect the safety of mining workers.

Nov 16, 2023

By R. V. Higgins

As part of a study of application of the Buckley-Leverett method to an analysis of oil-reservoir performance covering a wide range of relative permeabilities and oil saturations, a method has been devised for quickly deter-mining average water saturation at breakthrough from relative permeability data. The base for the relative permeability used in the report is either the permeability to air or the effective permeability to oil at the irreducible water saturation. The permeability to air also was used because of the large backlog of air permeabilities available to reservoir engineers. The basic data were calculated by an electronic computer and are presented in a single graph from which the point of breakthrough may be obtained. In this study the water saturation at the beginning of the depletion is the connate or interstitial or irreducible water saturation. These water saturations are considered to be synonymous and to have a practical value.

Jan 1, 1960

By C. Samson, R. S. Smith, S. W. Hefford

"Abstract - Time-domain electromagnetic systems are most sensitive to highly conductive targets during the transmitter on-time. Data collected during the on-time is highly influenced by the geometric relationship between the transmitter and the receiver. Unless corrections can be applied for these geometric variations, the ability to correctly detect and identify highly conductive targets can not be fully realized. Variables affecting the relative position between the transmitter and receiver include changes in the position of the receiver with respect to the transmitter, variations in transmitter attitude, and transmitter loop deformation. The level of accuracy in the determination of the relative geometry required to permit complete removal of the effects due to geometric variations is different for each of the variables and is dependent on the depth of the target. The most influential geometric variation involves changes in the relative position of the receiver with respect to the transmitter along the direction of flight; this variable, therefore, requires the highest degree of accuracy. The accuracy required for receiver motions along the vertical direction is roughly one order of magnitude less, and in the lateral direction, several orders of magnitude less. The objective of this paper is to relate the sensitivity of the response to transmitter-receiver geometry to the ability of an airborne, time-domain electromagnetic system to resolve a highly conductive vertical target. This is achieved by a detailed analysis of the effect of the individual x, y, and z distances between the transmitter and the receiver, the transmitter attitude (roll, pitch, and yaw), and transmitter deformation.Sommaire - Les systèmes électromagnétiques en domaine temporel sont particulièrement sensibles aux cibles à forte conductivité durant le temps d’excitation. Les données collectées durant l’émission du transmetteur sont fortement affectées par les relations géométriques entre le transmetteur et le récepteur. Si un facteur de correction n’est pas introduit pour tenir compte de ces variations géométriques, la capacité de ces systèmes à détecter et identifier correctement les cibles fortement conductrices ne peut pas être pleinement réalisée. Les facteurs affectant les positions relatives du transmetteur et du récepteur comprennent les changements de position du récepteur relativement au transmetteur, les changements d’altitude du transmetteur et la déformation de la boucle du transmetteur. Le degré de précision requis pour déterminer la configuration nécesaire pour compenser complètement l‘effet des changements géométriques est différent pour chacune des variables et dépend de la profondeur de la cible. Les changements géométriques qui ont le plus d’influence sont ceux qui font varier la position du récepteur relativement au transmetteur dans l’axe de la ligne de vol; c’est donc cette variable qu’il faut contrôler avec le plus de précision. La précision requise pour le suivi des mouvements du récepteur le long de l’axe vertical est moindre d’environ un ordre de grandeur, tandis que selon l’axe latéral elle est diminuée de plusieurs ordres de grandeur. Le but du présent article est d’établir comment la susceptibilité de la réponse à la géométrie transmetteur-récepteur affecte la capacité d’un système électromagnétique en domaine temporel aéroporté à reconnaître une cible verticale fortement conductrice. Cet objectif est atteint par l’analyse détaillée de l’effet individuel des distances x, y, et z entre le transmetteur et le récepteur, l’attitude du transmetteur (lacet, roulis, tangage) et la déformation du transmetteur."

Jan 1, 2006

By W. A. Mathews

We report on the progress of an automated mineralogical deportment of fluorine (F) in two portions of the Grasberg District for the development of metallurgical amelioration protocols for Cu sulfide concentrates. Fluorine detection limits in automated SEM technologies range from 1% (TIMA) to about 9% (QEMSCAN), however substitution in hydrophobic minerals or those reporting to concentrate is typically much lower (

Mar 2, 2022

By J. I. Paige

The Bureau of Mines studied methods for recovering unreacted titanium minerals and petroleum coke from titanium chlorination plant wastes prior to neutralization treatment with lime. The objective was to recover valuable raw materials and to reduce the amount of waste materials that must be treated for disposal. Samples of solid wastes were physically beneficiated by gravity concentration (tabling) to recover titanium minerals containing 69.0 to 92.4 wt-pct Ti02 and by selective carbon flotation to recover petroleum coke containing 94.0 to 96.8 wt-pct C. Laboratory data indicate that the recovered titanium mineral would decrease the amount of solid waste to be disposed of from 32.8 to 53.9 wt-pct. The recovery of coke would further decrease the amount by additional 32.9 wt-pct. Preliminary tests conducted on recovering vanadium, chromium, and columbium from liquors obtained by leaching chlorination residues also have shown that (1) 97 pct of the vanadium was extracted from leach liquors in a two-stage solvent ex-traction procedure and (2) 58 pct of the columbium and 40 pct of the chromium were separated from the leach liquors by an ion exchange technique using a strong acid resin.

Jan 1, 1982

By Robert Stefanko

The following tables contain the average, maximum and minimum power parameter levels for several mining machines. Power factor is listed only for defined transducer output regions. The reasons for the undefined areas are provided in the Instrumentation Chapter. Several maximum voltage drops are included, and are computed from the no load line-to-line voltage: Again, the drops are from measurements at the low side of the load center. The machines are: Continuous Miners; F6A Alpine 76AM Jeffrey (d-c) 8CM Joy 8CM (10CM) Joy 9CM-2AH Joy loam Joy CU-43-2H Joy 2 each CM26H Lee-Norse CM28E Lee-Norse Shuttle Cars; 18SC Joy 48S Torkar (a-c) 2 - 10SC Joys input to rectifier 2 - 16SC Joys input to rectifier

Jan 1, 1973

By Christopher Haycocks

The growth of computer and ground control technology in recent years, combined with an urgent demand for low-cost fossil fuels and mineral resources, has set the stage for full-scale utilization of computers in mine planning. Steeply rising production costs and the need to preserve the environment are placing great demands on engineers to improve their mining efficiencies, which can best be accomplished by applying the full capabilities of the computer. Pressure to develop and perfect programs with an immediate potential for improving mine de- sign, reducing mining costs and extending the viable coal reserves of the country has already come to bear in the form of exploding energy requirements, environ- mental considerations and the visible limitations of other energy sources. The computer program discussed in this paper, RAMPLAN (Rock Mechanics Applied to Nine Planning), was constructed as part of a continuing effort at Virginia Polytechnic Institute & State University under the sponsorship of the Office of Coal Research to develop a suite of programs to benefit the mining engineer in improving mine design and evaluation techniques. This program averages out structural data values obtained from randomly placed or gridded point sources across a mining property and uses these values in structural design equations. The basic purpose of the program is to provide accurate estimates of mineable tonnages, based on a realistic assessment of structural conditions existing in the deposit, for use in subsequent evaluation programs. Program output, however, also provides sound engineering data for the mine planner to use in planning and laying out new properties. Mining dimensions produced by the program provide a good starting point for initial layouts; and as more refined procedures are developed for increasing and improving the quality and quantity of information from boreholes, this information may be used with increasing confidence. The rock mechanics principles utilized in the program are generally well-established with full details provided to the user. To produce meaningful results extensive input data, obtained from exploration borehole core data, outcrop sampling points, or mine samples, are required. To assist the engineer, details of the types of tests that should be conducted have been listed. By including all of the ground control equations in the program the otherwise long and tedious calculations can be performed easily and quickly, and the work can provide the basis for a more detailed ground control study. The program is written in Fortran IV Level G to run on an IBM 3701155 ASP and requires 156K storage.

Jan 1, 1973

By J. A. Kosek

Work has been carried out under Bureau of Mines Contract No. HO395132 to develop and fabricate gas sensors for mining applications. Promising new instruments have been designed, developed, tested and supplied to meet BuMines requirements. These instruments include prototype 1) remote-sensing, diffusion-type CO monitors for mine operation which can be operated in conjunction with a surface computer, 2) control modules for alternate in-mine readout of the remote diffusion type CO monitors, 3) personal CO diffusion-type dosimeters and 4) personal NO diffusion-type dosimeters. In addition, retrofit modifications were made to update and optimize operation of CO and NO2 direct-reading type detectors provided under a previous contract. Studies were conducted to evaluate and demonstrate the availability of stable, portable N02 calibration sources for NO2 instrumentation. The use of selected, commercially available cylinder sources for NO2 instrument calibration were recommended. Additional studies were also conducted to investigate the feasibility of instrumentation for rapidly monitoring CO, NO and NO2 in diesel exhaust.

Jan 1, 1981

By Patrick J. Hannigan, Alex Ryberg, Rozbeh B. Moghaddam

Driven piles are widely used for foundation support. In the vast majority of cases, an increase in pile capacity occurs with time which is referred to as “set-up.” However, in a very limited number of cases, a decrease in capacity with time can occur. This phenomenon is referred to as “relaxation.” This paper will provide a brief review of the relaxation phenomenon, as well as pile driving information and dynamic test data on cases where relaxation has occurred. The pile types in the presented relaxation cases include H-piles, open-end and closed-end pipe piles, prestressed concrete piles, and prestressed concrete piles with H-pile stingers. The soil conditions where relaxation occurred includes dense to very dense fine sands, heavily over consolidated clays, and weak laminated rocks. Relaxation information from 36 piles at 26 sites is assessed. The collected data will assist foundation designers by identifying the subsurface conditions where relaxation has occurred, as well as by documenting the corresponding relaxation magnitude. One method of addressing relaxation when it is encountered is to drive the foundation piles to a greater end of initial driving capacity than required long-term. Hence, the identification and quantification of the relaxation magnitude will be beneficial to foundation designers installing similar pile types in similar subsurface conditions. The paper will also present pertinent observations and recommendations on mitigating relaxation when encountered. INTRODUCTION One of the earliest observations of a decrease in redriving resistance following initial driving was reported by Miller (1937). He reported that piles driven into a saturated, coarse grained soil could lose 40 to 50% of their resistance when redriven 24 hours after initial driving. Yang (1956) similarly reported that after a break in driving, a decrease in driving resistance could be encountered for piles driven in dense fine sand, inorganic silt, or stiff fissured clay. Parsons (1966) in his paper that described piling difficulties in the New York City metropolitan area termed this phenomenon “relaxation”. In this time period, pile capacity was most often evaluated from a pile driving formula frequently checked by a static load test. Hence, the true magnitude of the capacity decrease on a given pile was often poorly quantified. Furthermore, dynamic measurements that could determine what influence driving system performance variation had on the observed redriving resistance were not yet readily available.

Jan 1, 2019

By P D. Munro

"This is a reprise of the paper ‘Back to the Future &ndash; Why Change Doesn’t Necessarily Mean Progress’ presented to the Tenth Mill Operators’ Conference in 2009. It was observed that the ‘boom and bust’ cycles of the industry, together with trends in tertiary education and the effects of fly-in fly-out (FIFO) operations raised serious questions about the sustainability of human capital in the mineral processing sector.In 2016 we find ourselves in a ‘bust’ after enjoying a decade of the longest commodity price ‘boom’ in a century. In the ‘boom’ did we:make any technological breakthroughs?put measures in place to improve our human capital, especially in the area of ‘professional formation’?The paper makes observations on the current performance of mineral processing engineers and the organisational milieu in which they operate. It questions whether mineral processing engineers are actually ‘adding value’ at some sites given their organisational and operational practices.Some technical trends are examined and what it might mean for mineral processing engineers.Given the above and demographic trends for mineral industry professionals, changes to the seemingly current laissez-faire model of professional development are proposed.Citation:Munro, P D, 2016. Back to the Future - Still on the Dark Side, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 341&ndash;348 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016