Search Documents

By H. C. Hamontre

[The Bureau of Mines well-bore caliper was designed to provide an instrument that could be operated through 2-inch tubing, which 'a used particularly in many input wells on water-flooding projects of eastern, Kansas and northeastern Oklahoma. It should find wide application elsewhere under many other conditions where it has not been possible previously to make caliper logs with the larger probes used on other instruments. The caliper has three additional advantages over other instruments of this type: (1) It measures 4 radii (up to 18 inches) 90° apart with an accuracy of ± 1/4 inch; (2) the measuring arms can be opened and closed at will by remote control; and (3) it is run and operated on a single-conductor, armored electric cable (Amergraph, type 1-H-0). The caliper probe is 1-3/4 inches in diameter and approximately 6 feet in length. The electrical control and measuring circuits are encased in a stainless-steel tubular case. Measuring arms, made of 5/16-inch aluminum tubing, are attached near the lower end of the instrument. Distances the arms are extended are indicated t the surface by a meter calibrated to read directly in inches. Depths at which the radii measurements are taken are indicated by a wireline depth indicator on the cable-reeling. The instrument is not affected by pressure or temperature, it can be run open hole or under pressure through a lubricator. This paper describes and illustrates the instrument and outlines the operating procedures. A bibliography at the end of the report gives references to articles and patents on the development and use of other well-bore calipers.]

Jan 1, 1954

By Lloyd Williams

A vertical air shaft in the Birmingham, Ala., iron district was sunk with a circular cross section and lined with concrete at a relatively low cost to provide needed ventilation for an iron-ore mine. The method of sinking the shaft is described, and the costs are stated in mar-hours with a descriptive list of equipment and a statement on the size and use of temporary buildings. Preparation began May 2, 1955, and the shaft was completed at a depth of [680] feet by September 22, 1956. By October 1956, all temporary building and [aft]-sinking equipment had been removed. The total direct-labor cost for the operation, including preparation and dismantling, was 50,700 man-hours, or 30.2 man-hours per foot. Total rock and dirt removed amounted to 17,523 cubic yards (in place), and the shaft lining required 4,635 cubic yards of concrete to form a circular air shaft with an inside diameter of 16 feet.

Jan 1, 1960

By J M. Nel

Richards Bay Minerals (RBM) has recently undertaken an exercise to improve orebody basal definition. Older mineralisation bases (pre-2005) were highly erratic using old protocol reverse circulation (RC) (also known as Air Core) drilling and interpretation. The erratic nature of this estimation tool, resulted in impractical modelling towards the end of mineralisation (EOM), difficult mine design and unrealistic reconciliation. New protocol drilling, which includes high definition SONIC drilling data, has provided more data to be available for more accurate interpretation. Recent advances in drilling methodology has allowed for better penetration depths for SONIC drilling, which was previously restricted to approximately 80 m (pre-2005). This improved data set allows more emphasis on geological interpretation with factors such as lithology, slime content, and mineral species distribution. These factors when in unique combination enable more accurate and realistic EOM data points. These points are modelled into surfaces using conditional simulation techniques and result in a vastly smoother surface and consequently, a more representative resource.

Oct 5, 2011

By Raymond W. Hiteshue, Sam Friedman, Robert Madden

Experiments were made in a semicontinuous unit to provide engineering data for designing experimental continuous systems . These systems would be used to study the hydrogasification of hvab coal and char (from lowtemperature carbonization ) to high - Btu gas . In experiments at 800 ° C and with a coal residence time of several seconds , yields of hydrocarbon gases increased from about 2,000 scf / ton of maf coal at 250 psig to 7,000 scf at 1,000 psig . With 15 minutes residence time , yields increased from 8,000 scf/ton of maf coal at 250 psig to 17,500 cubic feet at 1,000 psig . In all cases , small quantities of heavy oils were produced along with the gaseous hydrocarbons . Production of oils could be minimized with a corresponding increase in gaseous hydrocarbons by increasing the retention time of the volatiles within the hot zone . Yields of gaseous hydrocarbons from char were slightly greater than from coal under similar conditions . Although the hydrogasification reaction is very pressure dependent , substantial quantities of coal (40 to 60 percent ) could be reacted to gaseous hydrocarbons at pressures as low as 50 psig provided reaction temperatures were increased to 1,200 ° C. It was also demonstrated that a hvab coal could be hydrogasified continuously without incurring agglomeration . This was achieved by dispersing coal in a relatively large reactor with concurrent flow of hydrogen . At 1,000 psig and 800 ° C , it was possible to react about 35 percent of the coal and to produce a gas containing up to 52 percent methane .

Jan 1, 1964

By P. R. Warner

This paper reviews the development of certain aspects of the electrical specifications of Anglo American?s suite of specifications for gearless mill drives (?GMDs?). These specifications are based on experiences in both Anglo American?s and others? operations, benchmarking against large hydro generators, the advice of industry and university experts, and continuous close co-operation with OEMs. To achieve a step change in availability additional final testing and electrical protection have been implemented, insulation requirements have been specified for machines to be operated at high altitude and clean area and access control systems have been developed.

Jan 1, 2012

By Robert Alfred

This paper is one of a aeries being published by the Federal Bureau of Mines on methods and practices used in mining and preparing crushed stone for market. Performance, in terms of units of work or tons produced per machine and per operator man-hour, is given whenever that information can be obtained. Direct operating costs are useful for comparing different methods and are included if available. In addition to descriptions of equipment and methods used the Bureau considered it desirable to discuss the engineering reasons for the choices that have been made, This paper is particularly concerned with the operation of the Liberty quarry and plant of the Campbell Limestone Co, The plant is in Pickens County, adjacent to the main line of the Southern Railway, and is about 18 miles west of Greenville, S, C. Access also is available by United States Highway No, 123, The company's main offices are at Knoxville, Tenn.

Jan 1, 1958

By S R. Williams

There is a sense of geometallurgy being new; a new methodology for mining project development and improved operational strategy. One of the main challenges that any ænewÆ technology faces is a validation of the value and the need to produce case studies. However, producing case studies can often be problematic particularly given the long cycle from mineral deposit project, through feasibility and construction to stabilised operation of a mine.However, the roots of geometallurgy go back quite some time. Successful practices with geometallurgy can be seen from as early as the 1980s. Many times those practices were not called geometallurgy but something else and, in other cases, what can be seen are various components of the geometallurgical ævalue chainÆ.This paper will analyse a selection of published past practices from a geometallurgical perspective to demonstrate the value realised from the application of this methodology. The paper will then make some general comments on where this history of work in geometallurgy has lead us to and what are the challenges today for the geometallurgical effort.CITATION:S R Williams, 2013. A historical perspective of the application and success of geometallurgical methodologies, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 37-48 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

By W. W. Fowkes

The Federal Bureau of Mines examined a low-temperature tar obtained from a small-scale commercial unit for carbonizing North Dakota lignite for products that might be important to the economic processing of the tar. Tie tar may be divided into three distinct parts: (1) Tar acids, 45 volume-percent; (2) tar bases, 1 volume percent; and (3) neutral compounds, 54 volume-percent. It has a boiling range of approximately 150° to 380° C. (the decomposition temperature) and yields 18 weight-percent as hard pitch. The tar distillate up to 365° C. may be separated as: (1) Tar acids, 48 volume-percent; (2) tar bases, 1 volume-percent; and (3) hydrocarbons, 51 volume-percent. The tar-acid distillate, boiling to approximately 265° C., was characterized in some detail; the neutral fractions and the tar bases were less thoroughly examined. In general, as might be expected of a primary low-temperature tar, the lower boiling fractions are less in quantity compared with the usual high-temperature tar. The homologous series of each major class appears to be rather complete, although some components are present in very small amounts. The tar is quite unstable thermally, and might be more conveniently processed by extraction methods rather than by distillation procedures. The neutral fraction of the tar is highly aromatic, and might be considered as base stock for the production of liquid fuels.

Jan 1, 1961

By P. Halsall

Smelters of medium or low grade tin concentrates must recover a high proportion of tin from iron-bearing slags or concentrates; the volatility of tin sulphide makes possible the production of iron-free tin fume. Laboratory work defined conditions which would promote the sulphidisation of tin slags and concentrates melted with them, to result in tin recovery as fume, and a residue of less than 0.5% Sn content, which could be controlled to vary with the value of tin. Subsequently pilot-plant work on 6-tonne and 15-tonne scale led to a commercial plant of 45 tonne. capacity (1962), for melting and fuming primary and secondary low-grade tin materials by submerged combustion. Some factors contributing to the rate of Working expressed in terms of the 'half-life and the amount of work done, the 'half-life-tonne' are studied, leading to the design and operation (1972) of the 100-tonne water-jacketed unit, presently in use, treating a wide range of slags and low tin-content ores and residues.

Jan 1, 1983

By Bruce McDonald

This report contains the Phase I findings of a study to select and test devices for preventing lack of alertness in haulage truck drivers. The extent of the problem was determined by visiting surface metal and nonmetal mines, interviewing drivers and safety personnel and reviewing accident reports. A number of devices for detecting a lack of alertness were considered and three were recommended for testing in actual operation.

Jan 1, 1977

By C. M. Clapperton, K. E. Darke, A. J. Boyce, C. M. Rice, S. D. Redwood

"Abstract - The Kori Kollo gold deposit is hosted by a c.15 Ma sericitized dacite stock in the La Joya district on the Bolivian Altiplano. The mineralization is of the Bolivian polymetallic vein (BPV) type, with a significant amount of the gold reserves contained in the oxide cap. Field and microscopic studies, K-Ar dating, ??34S values of pyrite, alunite and jarosite, and ??18O values of alunite and jarosite demonstrate that some of this gold is supergene. Two types of supergene gold are present: minute gold grains, 1 to 10 microns across, of high fineness and associated with jarosite and iron oxy-hydroxides; and ‘invisible’ gold, which is probably sorbed onto minerals such as jarosite and iron oxy-hydroxides.Pyrite ??34S values fall in the limited range -3.5 ± 0.6‰, consistent with a magmatic origin. Sulfate ??34S values are homogeneous and overlap closely with those of pyrite (-1.2 ± 2.1‰), which supports petrographic evidence that sulfates replaced pyrite. By contrast, sulfate ??18O values are inhomogeneous with a large range (alunite +2 to 26‰, jarosite -5 to +18‰). These data are interpreted as reflecting kinetically controlled reactions involving various proportions of atmospheric oxygen and local meteoric water. This is typical of supergene alteration and is due to the seasonally dry climate of the Altiplano.The oxide-zone mineralogy is dominated by sulfates and iron oxy-hydroxide minerals with some phosphates and halides, which indicates that the groundwaters were acidic, oxidizing and relatively saline. Under these conditions the most likely complexes responsible for gold mobilization are halides.Geological data and K-Ar ages indicate that oxidation of the BPV deposits began at least around 11 Ma and possibly up to 15 Ma ago, and that supergene alteration lasted until around 4 Ma. During this period, erosion was minimal. Although supergene processes have been active on the Bolivian Altiplano since the Middle Miocene, in contrast to Northern Chile, enrichment of gold has not occurred."

Jan 1, 1997

By C. M. Clapperton, K. E. Darke, A. J. Boyce, C. M. Rice, S. D. Redwood

"The Kori Kollo gold deposit is hosted by a c.15 Ma sericitized dacite stock in the LaJoya district on the Bolivian Altiplano. The mineralization is of the Bolivian polymetallic vein(BPV) type, with a signi?cant amount of the gold reserves contained in the oxide cap.Field and microscopic studies, K-Ar dating, ??34S values of pyrite, alunite and jarosite, and ??18O values of alunite and jarosite demonstrate that some of this gold is supergene. Two types of supergene gold are present: minute gold grains, 1 to 10 microns across, of high fineness and associated with jarosite and iron oxy-hydroxides; and ‘invisible’ gold, which is probably sorbed onto minerals such as jarosite and iron oxy-hydroxides.Pyrite ??34S values fall in the limited range -3.5 ± 0.6‰, consistent with a magmatic origin. Sulfate ??34S values are homogeneous and overlap closely with those of pyrite (-1.2 ± 2.1‰), which supports petrographic evidence that sulfates replaced pyrite. By contrast, sulfate ??18O values are inhomogeneous with a large range (alunite +2 to 26‰, jarosite -5 to +18‰). These data are interpreted as reflecting kinetically controlled reactions involving various proportions of atmospheric oxygen and local meteoric water. This is typical of supergene alteration and is due to the seasonally dry climate of the Altiplano.The oxide-zone mineralogy is dominated by sulfates and iron oxy-hydroxide minerals with some phosphates and halides, which indicates that the groundwaters were acidic, oxidizing and relatively saline. Under these conditions the most likely complexes responsible for gold mobilization are halides.Geological data and K-Ar ages indicate that oxidation of the BPV deposits began at least around 11 Ma and possibly up to 15 Ma ago, and that supergene alteration lasted until around 4 Ma. During this period, erosion was minimal. Although supergene processes have been active on the Bolivian Altiplano since the Middle Miocene, in contrast to Northern Chile, enrichment of gold has not occurred."

Jan 1, 1997

By R. A. Beall, W. E. Anable

The purification of hafnium by electron- beam melting at moderate energy inputs and at low pressures was examined in detail . Most metallic impurities and hydrogen were removed in the first few minutes of operation ; oxygen , carbon , and nitrogen were removed at a slower rate . Samples treated by electron bombardment suffered a small loss of weight and a gradual lowering of hardness . The magnitude of each change varied with the energy input and the duration of the melt . Analysis of the data confirms the loss of oxygen as a hafnium monoxide . Approximate activity coefficients for other contaminants are given .

Jan 1, 1964

By William F. Boericke

KIRKLAND LAKE and Porcupine in 1931 accounted for more than $41,625,000 of Ontario's total gold production of $43,117,688. For the first time, the younger camp surpassed the older in gold output, producing $21,734,000 against $19,891,000 for Porcupine. Present output of both camps is increasing, and should pass the record figures of 1931 before the year is out. In May of this year, Porcupine mines milled 285,759 tons, with a bullion value of $1,810,009; the corresponding figures for Kirkland mines are 149,188 tons and $2,104,757. A much higher average value per ton for Kirkland ore, $14.10 against $6.33 average for Porcupine accounts for the difference. The two fields are about 100 miles apart by rail, and there are important differences in the character of the ores, which accounts largely for the difference in milling costs and in final tailing values, despite excellent metallurgical work in both the fields.

Jan 1, 1932

By H. G. Skavlem

This paper is prepared the United States Bureau of Mines and is descriptive of methods, practice, and costs at the McIntyre Porcupine Mines, Ltd., Schumacher, Ontario. The property is located in the Pearl Lake section of the Porcupine mining district. It is reached by a branch line of the Temiskaming & Northern Ontario Railway from Porquois Junction. There is also a good motor road into the district. The Hollinger Consolidated Gold Mines and the Coniaurum Mines, Ltd., are adjacent properties. Power for both the mining and the pulp and paper industries in the district is supplied by an extensive development of the water-power resources. Weather conditions are favorable for mining operations.

Jan 1, 1933

By Y. Yhang, D. C. Sego

ABSTRACT This paper evaluates the potential of freeze-thaw dewatering using Albian mature fine tailings (MFT). Freezing tests were first performed to study the effect of freezing rate on dewatering efficiency. Lower freezing rate resulted in higher thawed solids content and shear strength. Subsequently, large strain consolidation tests were conducted to investigate consolidation behaviour and how it is affected by freeze-thaw. The consolidation behaviour was presented in terms of effective stress versus void ratio and permeability versus void ratio. The results can be used to predict the field behaviour of Albian MFT and optimize the application of freeze-thaw for MFT dewatering.

Jan 1, 2014

By P Holtham, K Duffy, L Pyle, W Valery

The mining industry is becoming increasingly focused on pre-concentration due to its potential economic and environmental benefits, particularly for the more complex, low-grade, high throughput operations now being developed. Advances in technology have seen bulk ore sorting (BOS) trialled at several operations. However, BOS should not be seen as a ‘silver bullet’, it can offer significant benefits, but only under the right conditions. Deposits with interspersed mineralogy or disseminated, fine-grained minerals can be difficult for BOS. Large batches of barren or low-grade material are required for BOS to be effective. Hatch has recently completed several studies for clients who believed that bulk sorting was the most suitable pre-concentration technique for their operation, based only on an assumed sorter recovery or on laboratory trials of the chosen sensor. However, minimal consideration had been given to the heterogeneity of the deposit, the achievable separation batch size or sensor repeatability. Evaluation of BOS needs to consider both heterogeneity and sensor suitability. The valuable or gangue mineral must be present in such a way that it can be separated effectively in the large bulk sorting batch sizes, without competing minerals or changing ore characteristics affecting the metal upgrade or recovery. Also, the sensor chosen must be able to detect either the valuable mineral, a proxy for the valuable mineral, or a gangue mineral for rejection with sufficient accuracy and precision (repeatability). This paper presents three recent case studies, emphasizing markers which indicated that bulk sorting was unsuitable for the project whilst highlighting the pre-concentration technologies which were applicable (including particle sorting, and coarse particle gravity separation). The modelling methodology, equipment sizing and forward work plans developed to verify these alternative solutions are also presented, demonstrating the key factors contributing to a thorough scoping assessment.

Aug 24, 2022

By G R. Howard, G Back

Management of information systems for data collection is essential to maintain data integrity and continuity, and manage loss control on a large world-class mine such as Telfer Gold Mine. This paper aims to describe the individual systems and protocols of geological data capture at Telfer, then focus on Quality Assurance Quality Control data as an example of loss control in practice. Loss control systems are required to provide capacity, flexibility, structure and management tools to enhance data interrogation. The data that have been collected can then provide geological, financial, environmental, and contractual information to optimise management of business best practice. Telfer Gold Mine is a wholly owned and operated subsidiary of Newcrest Mining Limited. The mine is located in a remote area of NW Western Australia, and has been operating for 20 years. Geological data have been collected at Telfer since 1973. The data include drilling, assay, geological, survey, structural and geophysical data. Data management has evolved through many systems with data stored on many different hardware and software platforms. Commencing in 1995, collation, standardisation and validation of the historic data was completed. This has resulted in the first Access based drill hole database incorporating all available drilling data. This drill hole database, now hosted in SQL Server, is the hub for all geology related data management systems. The Telfer Gold Mine Geology Department has developed a series of inter-related database systems in order to manage the core geology business issues. Databases relating to drill hole planning, drill contract management, geological logging, accounting (standard costing, forecasting, invoice reconciliation), quality control (QAQC), and environment rehabilitation have all been developed to manage loss control. Management effort to provide adequate data systems and protocols has driven the system from concept to utilisation. The improved productivity, data integrity and data analysis capabilities provided by the new database systems at Telfer have allowed for greater confidence in decision making. Systems such as the drill hole and QAQC databases, when utilised in the proper manner provide up-to-date data analysis for resource audits and contract negotiations. The loss control systems are essential to maintain confidence in data integrity and hence directly effect the future of mining at Telfer.

Jan 1, 2000

By H. W. Kilau

The Bureau of Mines used a high-temperature rotational viscometer to test basic oxygen furnace slags to determine fluorspar requirements and to evaluate colemanite and fused boric acid as substitute fluidizers. A continuous technique of viscosity measurement was adapted to better determine the viscosity-temperature profiles of volatile fluorspar slags. Criteria used for estimating slag fluidizer effectiveness were (1) the apparent solidification temperature, and (2) the temperature range of slag crystallization. Colemanite and fused boric acid in high-basicity slag were superior fluidizers to fluorspar when compared on the basis of boron versus fluorine concentration. Fused boric acid was nearly equivalent to ceramic-grade fluorspar when compared on a simple weight basis, while colemanite was inferior to fluorspar. Fluorspar slags volatilized fluorine during viscosity testing. Colemanite and fused boric acid slags were stable, no boron losses being detected. A fluidizing limit was found for fluorspar at 2.9 percent fluorine concentration; higher concentrations impaired viscosity and caused foaming and crusting of slag. Concentrations of boron up to 4.4 percent resulted in very fluid slags with no fluidizing limit.

Jan 1, 1978

By Guy Ervin, Delwin D. Blue, John E. Conley

"INTRODUCTION Extraction of alumina from various materials, such as low-grade bauxite and clay, by means of a lime-soda sinter has been the subject of a number ofinvestigations (1, 2, 3, 4, 5, 7, 9, 10, 11, 12, 13, 16, 17). 5/ in recent years, Although many of the details of these investigations are lacking, it is believed that there is one difficultly that frequently develops under certain conditions, namely, that of thickening or gelation of the slurry formed during extraction of the sinter. If gelation occurs even to a slight extent* Serious mechanical difficulties result, very low liquor recoveries are obtained, and the extraction step becomes virlually inoperable. Under 'favorable conditions, a solid gel is formed which can only be removed from the equipment with great difficulty. At the Eastern Experiment. Station of the Bureau of Mines in College Park, Md., a study of lime-soda processes was begun in November 1941. This work has included studies on low-grade bauxites, kaolin clay, and nodular diasporic clay. Gelation was most serous with kaolin clay and least with diasporic clay. As a part of the Bureau's investigation, a study was made of the effect of the pertinent variables on gelation. The results permit the selection of various sets of conditions at which gelation will not occur. These data are essential to the final selection of optimum conditions for the over-all process."

Aug 1, 1946