Search Documents

The term geochemistry - chcmbtry' of the earth - is almost limitless in its implied subject, but of recent years a major trend of research in this field has been towards economic application in the search for mineral deposits, and in particular for those of some ofthe less common elements for which a demand now exists.Geochemistry is in a state of slow transition from a purely descriptive subject to a fundamental science concerned with the relationships that exist between the distribution of the elements in the earth's crust and the physical characteristics of the atoms of those elements. The progress achieved promises a set of basic principles which will relate the atomic characteristics of an element to the physico-chemical conditions that make for its dispersion or concentration. This means that, given a geological map of an areasufficiently detailed for the physico-chemical conditions existing in past geological eras to be deduced, there is the possibility that the relative distribution throughout that area of any element present, and its likely mode of occurrence, could be predicted from a consideration of its atomic characteristics.Since the atomic characteristics of the elements are becoming increasingly well defined by physical research, the attainment of this ideal of prediction depends upon:(a) the strengthening of geochemical theory; and(b) the development of petrological and mineralogical methods of assessing the conditions of temperature and pressure prevailing in geological formations at various stages in their history.The other prime requirement is a d.etailed geological map - a requirement that is all too often lacking.The fact that there has been very little "geochemical approach" to problems of economic geology in Australia should not be taken to mean that there is little point in trying to develop such an approach here in as active and as rigidly scientific a manner as possible. The degree of success that has attended the attempts so far made, to which reference is made below, suggests the reverse, particularly in view of the relatively slight cost involved if the investigations were properly organised on a centralised basis. There are three aspects of geochemistry that are directly applicable to the search for economic minerals.(a) The classic technique of the prospector can be made more sensitive and reliable by the use of modern equipment coupled with the application of geochemical theory to geological and structural data. The case of the rare alkali elements (see below) is givenhere as an illustration of the way in which the distribution of elements can be predicted from the first principles of geochemistry, thereby replacing the prospector's dependence on his "sixth sense" that enabled him to suggest that a certain area of formation was"favourable" for the occurrence of a certain type of mineral deposit.At its best, this sixth sense amounted to an almost subconscious correlation of all relevant associations and typical occurrences of the particular mineral experienced by the prospector during his...

Jan 1, 1950

By N. V. Gorelikova

A new type of zirconium mineralization has been recognized in the Devonian volcanic rocks from an orogenic depression in the Central Kazakhstan. The most characteristic features of this deposit are the fine-grained nature of the zirconium mineralization, an unusual texture of the zirconium ores, and a close association of zirconium with phosphorus in the ores. Zircon grains form fine globular aggregates with the features of hexagonal crystal habit. In addition to crystalline zircon, the ores contain metacolloidal zircon, similar to hydrozircon. The morphological and textural features of the zirconium ores suggest that the deposition of ore deposits took place at a low temperature from colloidal solutions. It is believed that this deposit should be considered to be a new type of zirconium mineralization that is related to low-temperature hydrothermal processes.

Jan 1, 1995

By James Hyslop

THE Pittsburgh seam in eastern Ohio has an average thickness of 5 ft and lies almost level Immediately above it is a layer of draw slate about 12 in thick, which normally has little structural strength, and is pulled down or allowed to fall as mining progresses Above the slate is a, variable thickness of roof coal, which in places will stand for the life of the working section and sometimes for the life of a secondary haulage entry The thickness of this roof coal varies from zero to 24 in In general, however, it does not provide a satisfactory roof, and usually is supported or pulled down About it is a mass of shale, soapstone and clay, of quite variable thickness, usually running from 5 to 8 ft and above this is a stratum of hard blue limestone, which provides a permanent roof Where entries are to be used for less than five years, the roof usually can be supported by wood or steel crossbars, but if they are to be used for a longer time, roof support is a serious problem All the roof material below the limestone disintegrates when exposed to air or moisture, and in a few years falls out between and over the crossbars Where this material is removed for a considerable height above the coal, the ribs scale and thus contribute to a further collapse of the roof As the height of the entry increases, cost of timbering is greatly increased, a problem that always is encountered where old entries are recovered or repaired METHODS During the last six years the Hanna Coal Co has used gunite for roof protection in mine entries Two general methods of guniting are practiced The first consists of the application of a I-in coating of unreinforced material This application does not provide any appreciable structural strength, and serves principally to protect the strata from exposure to air and moisture With the other method a coat at least 2 in thick is applied and provided with suitable reinforcing, which provides a structural strength proportional to the thickness of the coat and the reinforcing used The first method is adopted as a general practice, modified only where additional support is required "Gunite" is a mixture of cement, sand and water * The cement and sand are thoroughly mixed and screened before being fed into the hopper of a cement gun After the hopper lid is closed, compressed air is applied to force this dry mixture through the hose line to the nozzle, where the quantity of water needed to effect the proper hydration of the cement is added The coating is dense, and stronger than poured concrete

Jan 1, 1941

Coal, America's most abundant fossil fuel, is expected to play a key role in our pursuit of energy independence. A substantial increase in coal exploitation will be required if we are to fulfill our future energy needs. It is essential that new developments continue if stable coal prices are to be achieved and maintained. The challenge of the mining industry is to continue these developments in the face of problems related to increasing labor costs, inflation and environmental restoration. With expectations of increased activity in surface coal mining, the U.S. Bureau of Mines has authorized this study to determine the preliminary economic and technologic feasibility of underspoil haulage in area strip coal mines and to identify geologic and geographic areas where such a system could be used. These objectives were met by literature search, data-gathering visits to several active area strip mines and by analyzing various haulage systems that were superimposed on three model mines. Potential advantages of such a system include: 1) improved mine design; 2) lower mine operating costs; 3) improved land reclamation; 4) lower manpower requirements; 5) lower mobile equipment requirements; and 6) smaller, less sophisticated maintenance facilities.

Jan 1, 1975

By W. J. Kennedy, John D. Gardner

Introduction During the past 10 years, energy costs in mining have risen from about 4% to as much as 25% of total production cost. When combined with declining ore grades, these costs exert inordinate stress on mine productivity. Industrial engineering techniques have traditionally been aimed at improving manufacturing facilities productivity, but they have been applied to mining as pressure for productivity improvement has increased. These techniques can perform four useful functions for mining operations by improving methods, equipment selection procedures, energy use through scheduling, and managing energy costs rather than being managed by them. This article discusses some of the standard techniques for productivity improvement, and how they can be adapted to perform these four functions. Pre-Production The best time to seek high productivity is when a mine is being planned. During pre-production, when most options are still open, an optimum mine design is achievable. At this time, major equipment selections are made, the layout, material handling systems, and processes are designed, and critical energy source decisions are made. By including explicit energy cost projections, decisions can be made that will save significant amounts of money per ton of ore over the life of the mine. Attention can also be given to often overlooked details such as lighting. Some of the same tools used in new mine planning are applicable to productivity improvements at an existing plant. These tools are the charting and modeling methods that have been developed by industrial engineers over the past 75 years. Energy Consumption Before any analysis of energy consumption can be performed, preliminary work is necessary to find the kind of energy used, how much it costs the plant, and when electrical peaks occur. Past bills should be examined to determine the monthly consumption rate and the cost of each energy type. These data should be adjusted to remove effects caused by production fluctuations or weather. Knowing when electrical peak demands occur is necessary because these determine either the electrical capacity needed or the amount that must be bought. At $500-$800 per kW for construction or $5-$15 per kW per month for purchase, they represent a significant cost. By the time these data are collected, planners should be aware of the importance of energy in the total cost of mine operation, and should have the most crucial time data for electrical peak demand. Flow Process Chart Reducing costs can be accomplished by a thorough look at mine systems and how altering one system causes changes in others. By developing and exercising models of production processes outward to the transportation of the final product, otherwise obscured weaknesses may become apparent. There are tools available for analyzing the mine and its associated systems; one of the most useful is the flow process chart. The flow process chart gives a system analysis of a production procedure by classifying all actions into one of five types: operations, inspections, transportation, delays without paperwork, and delays with paperwork. Operation: In an operation, the nature of something is changed. Examples are blasting, washing coal, and processing matter. Denoted by 0. Inspection: Examining an object for identification or to measure some attribute. Examples are determining whether a drill hole is deep enough, deciding how far to cut under an unsupported roof when operating a continuous miner, or checking the lubricant level on a truck. Denoted bye. Transportation: Moving an object from one place to another. Examples are transporting overburden, moving coal on a conveyor belt, and pumping water. Denoted by =>. Delay without paperwork: A delay that is an inherent part of the system. Examples include idle time of a continuous miner while waiting for shuttle cars or for roof bolting, crushed ore in a storage area waiting for grinding and flotation, and people from one craft waiting for another craft to finish. Denoted by D. Delay with paperwork: A delay that can be terminated only by some written authorization. Examples are coal that cannot be removed until authorized by a bill of sale and transportation orders, personnel records, maintenance, or spare parts. Denoted by V. In practice, the flow process chart is completed after data collection and a detailed examination of the process. Data collection is needed to answer questions on distance, quantity, and time for each of the operations. As the analysis is being performed, each step of the process is subjected to these questions: • Why is the step necessary? • What is being moved? • When does the step take place, and why?

Jan 11, 1983

By W. H. Oppelt

The continuous gasification of lignite in an externally heated alloy-steel re-tort was investigated by the Bureau of Mines, Grand Forks, N. Dak., from 1945 to 1951. The main objective of the long-term experimental program was to obtain data on the mechanical performance of this type of gasification retort, particularly the alloy-steel heat-transfer surface of the retort, when operated on large pilot-plant scale. At the same time, extensive experimental data were obtained concerning the effect of process variables and the effect of a limited number of design modifications on gasifier performance. In the period covered by this progress report 4 pilot-plant runs totaling 2,879 hours of operation were completed with the rolled-plate, 310-alloy reaction tube. Over 30 million cubic feet of gas, having H2-CO ratios from 2.1 to 4.4, was made by the partial gasification of 636 tons of 1-1/2-by 3/8-inch natural lignite. Rates of gas generation were from 8,200 to 14,300 cubic feet per hour. Three of the four runs were carried out with the lowered gas offtake or continuous-annulus design modification of the gasification retort. In the final run of the series, gasification of lignite from seven different mines in North Dakota and Saskatchewan, Canada, was investigated at similar combustion-space temperatures and lignite and steam feed rates.

Jan 1, 1955

By George I. Smith

Jan 1, 1985

Electrical trailing cable used to power coal mining machinery is frequently damaged in usage because of tensile strain or crushing effect of mining machines running over the cable. One of the repair problems is finding the exact location of a short or open in this cable so it may be spliced or otherwise repaired. The U.S. Bureau of Mines and FMC corporation signed Contract No. H0 122011 in August, 1971, to develop instrumentation for finding faults in coal mine trailing cable. This report describes performance of several existing instruments as trailing cable fault locators and also construction details and performance records of several cable fault location instruments that FMC designed, built and tested as part of this project.

Jan 1, 1973

By Lawrence J. Froisland

To aid in minimizing adverse environmental impacts of mining and mineral processing, the Bureau of Mines studied changes in soil characteristics in topsoil stockpiled during mining operations. Topsoil stockpiles in arid areas of New Mexico, Utah, and Wyoming were sampled over a 1- to 8-yr period to determine any changes in physical, chemical, or biological parameters in the top 15 ft of soil. Parameters examined in this study included soil moisture, pH, electrical conductivity, and cation exchange capacity; total nitrogen, organic carbon, carbon to nitrogen ratio, extractable potassium, and soluble phosphorus levels in the soil; general levels of bacteria activity in the soil; and productivity of the soil as measured by shoot yield in growth tests. Data were analyzed by multiple linear regression to determine possible effects of stockpile age and depth. Bacteria population counts, used as an indicator of goner l bacterial activity, was the only parameter found to be significantly correlated with stockpile age and depth at more than one site. Bacterial activity increased with depth at the two sites where it was measured. Activity increased with age at one site and decreased with age at the second. Significant changes in soil pH, electrical conductivity, and moisture were significantly correlated with stockpile age and depth at single sites. This study did not show significant, consistent deterioration in soil characteristics or growth yield of topsoil stored in stockpiles.

Jan 1, 1987

By Michael Horn

[An economic trading region made up of 22 eastern Washington, northern Idaho, and western Montana counties, with Spokane, Washington as the central place, was defined for this study. modeling system with the, 1985 county database was to create an Input/Output based model of the regional economy. The leading ice, with respect to income, employment, value of exports, and total industry output are shown for each county and the region. The value of total industry output from natural resource based industries is also shown for each county and the region. Interindustry transactions, final demand, and value added components for the region are shown in the Regional Gross Flows Table. The total gross output for the region is valued at $36.7 billion. Total industry output for the region is $18.1 billion. The region provides $5.4 billion in income to a work force of 286,000. Spokane County, Washington accounts for about 50 percent of the regional total industry output, income, and employment. Both Spokane County and then as a whole produce about 80 percent of the total industry output for final demand with remaining 20 percent going to intermediate inputs for further production. Spokane County exports about 43 percent of its total output while 35 of the regional output is exported. Exports account for more 50 percent of the total in 18 of the 22 counties within the region. About 9 percent of the total industry output from Spokane County and 19 of the total output from resource f: .t *III For counties Spokane a industry ? N from nafural resource based represents 18 percent ?.{1 to 71 s. ?-{ and averages 39 r. ?-11 of total county +' ' 7:. FS.-f.?) If t. Natural resource it us -t for more than 50 coutny 1 s ? sass in seven counties within region.]

Jan 1, 1992

By James C. Fowler

This report contains a description of the contract activities performed by ENSCO, Inc. under contract H0292025. The purpose of this project was to prove the feasibility of detecting hazards in a coal seam using a synthetic pulse radar. This work was conducted in three phases. The first was an analysis of the types of errors which might cause problems. The second was to build a breadboard radar and the third phase was to conduct a field test with the system. The work from each phase is discussed and the results of the field tests are presented. These results show propagation of the radar signal through 200 feet of coal along with reflections from 50 feet away. The final section contains recommendations for future development.

Jan 1, 1981

By M. Kanefsky

Two channel polarity coincidence and polarity difference statistics are analyzed. The signal, common to both channels, consists of sinusoidal bursts where the exact frequency of the signal is nearly known, but other parameters such as amplitude, phase, and pulse starting time are unknown. The noise inputs are dependent, narrow band, Markov processes. It is shown that the performance depends not only on the signal uncertainties, but on the precise shape of the cross-correlation functions between the noise in-puts. By using two polairty difference statistics in addition to the polarity coincidence statistic, it is shown that the decrease in performance, as well as the cost of hard limiting due to correlated inputs, can be made small.

Jan 1, 1981

By Gerald Greene

Tan various lead producers have given the subject of lead drosses much attention in recent years but the problem of their economical treatment is yet to be solved. Formerly the copper in the furnace feed was removed from the furnace in the form of matte. The speiss at that time consisted principally of the iron arsenide. The practice today is to roast off most of the sulfur and the copper in the feed forms a dross in the furnace, which is removed from the furnace with the lead. This material is poured into the drossing kettles and allowed to cool down to but slightly above the freezing point of lead. The copper dross, containing almost all of the arsenic and part of the antimony, is skimmed off and treated in a small reverberatory furnace at most plants. This is essentially a liquation process. The skimmed dross contains from 70 to 80 per cent lead, and much of this lead is liquated out. The products from this treatment are: (1) impure lead, (2) speiss and (3) matte. The speiss from the reverberatory furnace was studied in this research. The literature on the subject is of very little assistance, as almost no work has been done on the problem of establishing the exact identity of the various phases present. One author(1) states that speiss consists of a series of isomorphous compounds of the general formula FexAsy in which the Fe may be replaced by Ni, Co, Cu, Pb, Ag, Au, Pt, Zn, Cd and the As replaced by Sb, S and Bi. Hofman(2) states that the iron arsenide present is Fe5As.

Jan 1, 1935

By Frank W. Luerssen

Introduction "Austerity" is perhaps an overly generous description of the past three years in the American steel industry. Steel plants operated at an average of only 57% of their capability in 1982-84. The dismal losses for last year are still being totaled. But during the two years before this period, American steelmakers recorded an aggregate net loss of a staggering $6.8 billion. Steelmakers responded by closing numerous marginal facilities. And production capability was cut by 13.6 Mt (15 million st). Capital expenditures still averaged $2 billion annually. But this was inadequate to maintain the existing base of steelmaking facilities. The general economy experienced a satisfactory recovery during this period. American steel, however, continued to suffer from a lagging recovery in the capital goods sector. This was due to record penetration of its domestic market by imports and from very weak realizing prices on the volume that was available. In addition to the direct influx of offshore steel products - which itself depressed prices - the industry also became painfully aware of the growing importance of "indirect" imports. These came in the form of steel-containing producer and consumer durables. Industrial equipment and autos fabricated from foreign steel accounted for the equivalent of 6 Mt (6.5 million st) of lost market opportunity for domestic steel-makers last year. That is over and above the 23.5 Mt (26 million st) of direct steel imports. Given these factors, Inland Steel was not spared from the threeyear downpour of red ink. Despite its record of continuing modernization in steel, our single-plant location in the world's best steel-consuming market, and the high proportion of consumer durables related products, such as cold rolled and coated sheet in our mix, Inland suffered aggregate losses of $277 million during the 1982-84 period. Strategic Planning The foregoing establishes a perspective - a base from which we have restructured our view of the steel industry, and of our own role within that picture. Until possibly two years ago, this present weakness in steel demand was viewed around the world as an aberration, eventually to pass. By contrast, it is now recognized that austere times are the normal steel environment. The topic here is management of resources. This implies an emphasis on strategic planning. It is worthwhile to examine some of the more critical assumptions that were driving strategies among a number of steel companies just before the 1980s. Those projected characteristics of the future steel environment were arrived at through painstaking analysis. They were carefully and heavily quantified and were generally shared by outside observers and our peers within the steel industry. • First, the assumption was made that domestic steel demand would continue to grow at an average rate of 2% per year. • Second, it was assumed that this growth in the American market would continue to be filled predominantly by US mills. It was believed that increases in steel and steel-related demand overseas would absorb much of the ominously growing capacity of third

Jan 6, 1985

By Morgan L. Race, Matthew R. Glisson

"Most driven pile projects have plumbness limits from 0.25 in/ft (21 mm/m) to 0.5 in/ft (42 mm/m) to control bending stresses. For two projects, the project teams performed static load testing to evaluate performance of piles with sweep. One project, located in Grand Forks, North Dakota, used 9.625-inch (244-mm) diameter piles with a wall thickness of 0.395 inch (10 mm) and lengths ranging from about 130 to 160 feet (40 to 49 m). Measured pile sweep (lateral offset distance of the pile toe from the pile top) was between 12 and 17 inches (305 to 432 mm). Static load testing indicated that the piles could support the design load with axial deflection of less than 1 inch (25 mm) but only provided about 80 to 90 percent of the ultimate resistance at axial deflections of about 1.9 to 1.7 inches (49 to 43 mm), respectively. The other project, located in Shakopee, Minnesota, used 9.625-inch (244-mm) diameter pile but with a wall thickness of 0.352 inch (9 mm) and lengths around 50 to 90 feet (15 to 27 m). The measured sweep varied between about 20 and 63 inches (508 and 1,600 mm) for 9 of 214 piles driven at the site. Load testing indicated that these piles could provide the required design resistance with less than 0.3 inch (8 mm) of axial deflection and support the required ultimate resistance with about 0.5 to 0.6 inch (13 to 15 mm) to of axial deflection.INTRODUCTIONAnyone who has observed a significant number of piles has seen that, inevitably, the pile is not perfectly straight after driving. In spite of the best efforts of contractors, there are a whole host of reasons for piles to end up out-of-plumb or to have a curve, sometimes referred to as pile sweep. Most project specifications set limits for plumbness typically between 0.25 in/ft (21mm/m) and 0.5 in/ft (42mm/m) (USACE, 1991; PDCA, 2007; MnDOT, 2016; MoDOT, 2016). Closed-end pipe piles, including monotube or tapertube, are the only pile type that allow actual measurement of the final alignment of the pile.As Nadeem, et al. (2015) note, buckling failure of long, slender piles is the predominant mode of pile failure in soft soils. Pile sweep is just one source of buckling failure in long, slender piles. The nonlinear buckling analysis showed that increasing slenderness ratio and/or increasing degree of curvature decreases the loadcarrying capacity of a driven pile. Nadeem, et al. (2015) considered solid, steel pile with lengths from 24 to 66 feet (7.5 to 20 m), diameters from 9.75 to 26 inches (244 to 660 mm), initial bends from 2 to 6 inches (50 to 150 mm), and half- and quarter-sine shapes."

Jan 1, 2017

This report summarizes the work performed under USBM Contract No. H0395041. The primary objective of this work was to extend the noise control technology developed under earlier USBM projects to a wider range of load-haul-dump models to evaluate the general applicability of these techniques. Noise control treatments were designed, fabricated, and installed on three Wagner LHDs (an 5T-2B, ST-2D, and an 5T-8A) selected as demonstration machines for this project. The machines were evaluated either in production mines or at the Bureau's Lake Lynn Mine. The results indicate that it is possible to achieve overall noise reductions of between 4 and 8 dB using these techniques. Engine cooling and seal design were determined to be important design issues in such treatments.

Jan 1, 1984

By D. D. Runnells

This study focused on the chemical reactions between uranium tailings fluids and cores of subjacent bedrock from the site of the Cotter Corporation uranium mill at Canon City, Colorado. Actual and synthetic tailings fluids were forced through cores of bedrock. The pH of the effluent solutions was the dominant control on the behavior of dissolved species in solution. The pH depended on the presence or absence of calcite cement in the rocks. Calcite neutralized acidic raffinates and caused the precipitation of iron, manganese, aluminum, and possibly uranium. Chloride, sulfate, and sodium were not retarded upon passage through the cores, and sulfate and chloride should be useful as tracers of escaping tailings fluids. Zinc, copper, cobalt, nickel, uranium, and vanadium exhibited high mobility under acidic conditions and were strongly retarded at elevated pH. Calcium was released due to dissolution of calcite and ion-exchange. Magnesium was not retarded in concentrated solutions, but showed moderate retardation in dilute fluids. Potassium and ammonium both showed early retardation followed by breakthrough and mobility. The behavior of molybdenum was strongly dependent on pH, with retardation at low pH and mobility at elevated pH. Selenium was highly mobile under all conditions. Selenium should be a better tracer than molybdenum for many situations. Precipitation of carnotite appears to control the solubility of uranium and, possibly, vanadium. With the exception of the precipitation of aluminum and silica, all reactions were rapid.

Jan 1, 1983

By Patrick O. Shires, Harry W. Schnabel

With stable building sites becoming scarce in the greater San Francisco Bay Area, the new Summit Senior Care Facility is being built into the side of an unstable hillside adjacent to the San Ramon Regional Medical Center in San Ramon, California. This hillside has had a long history of instability and the site of the new Senior Care Facility required excavation into both a historic old landslide and a more recent active landslide. After a thorough geotechnical study, it was concluded that the best way to build the new facility would be to construct a tied-back retaining wall in the area of the old landslide, since it extended off-site onto two adjacent properties, and remove the active landslide and replace it with compacted fill before cutting into its toe area with an additional tied-back retaining wall. The design was further complicated by the proximity of the site to several active faults. In the area of the old landslide, the combination of an ascending slope behind the wall, landslide forces and seismic forces resulted in total design pressures between 365 to 4,575 PSF for a wall with a maximum height of 30 feet. The wall for the old landslide was constructed by first drilling and placing steel soldier piles in concrete. The tip of the soldier piles extended a minimum of 12 feet below the landslide plane that was up to 36 feet below the bottom of the wall. Permanent double corrosion protected tiebacks were then installed through the soldier beams and anchored below the slide plane. A shotcrete facing was then installed on the face of the wall. BACKGROUND The site of the Summit Senior Care Facility is located on the southwest flank of Mount Diablo adjacent to San Ramon Valley which is characterized by gently rolling hills. The San Ramon Valley Regional Medical Center, which opened in 1990, is located to the north and an existing church is located to the southwest. There are also private residences located to the southeast. The site is shown in Figure 1. Numerous faults run close to the site, the most significant of which are the Calaveras and Pleasanton faults. The site has also had a long history of slope instability and has been the subject of numerous investigations. Studies conducted in 1979 and 1984 concluded that there was a landslide in the area and recommended that a buttress shear key be constructed between the subject site and the existing church for a sewer main as well as removal and replacement of the head area of the old landslide to stabilize the hospital site. While two previous geotechnical studies in 2008 and 2016 identified slope instability, they did not recognize the genesis and limits of the old landslide on the western portion of the site or the limits of the active landslide on the eastern portion of the site.

Jan 1, 2018

The following list contains the names of members whose death notices have been printed in MINING AND MDTALLURY from April 5. 1944 through March 15. 1945, Biographical sketches published in MINING AND METALLURGY are indicated in the last two columns. [ ]

Jan 1, 1946

By T. L. Muldoon

The bagging of dry pulverized products using fluidized air packers creates severe respirable dust problems in many surface mining operations. During bag filling, excess air and product blows by the bag valve/nozzle interface. After bag ejection, dust blows out of the bag valve. During conveying and handling dust is released from the bag valve and dirty bag surface. Overexposure of the bagging machine operator and bag handlers is common. This report describes the development and testing of a new dust control system for bagging machines. The system features a new bag clamp design to reduce product blowby during filling. A controlled vacuum system removes excess air from the bag before ejection, eliminating the problems after bag ejection and during conveying and handling. The system has shown significant reductions in dust exposure for both bag machine operators and bag handlers. These reductions are achieved with no significant effect on total mill productivity.

Jan 1, 1985