Search Documents

By Kenneth Cottingham

The number of completions in 1944 in Ohio was only slightly greater than completions in the preceding year, but the initial daily volumes both of oil wells and gas wells declined considerably. The dry-hole ratio was a little lower than in 1943, even though in the year under review considerable effort was made to find new production. No new areas of consequence were discovered. Thirteen new gas pools, the largest of which was 1000 acres and the average 565 acres, were opened during the year. Eleven of these pools were in the Clinton sand, one was in the Oriskany, and one was in the Berea. Approximately 15 small pools might also be rated as discoveries, but because only one or two wells have thus far been completed in each, they cannot at present be properly evaluated. The latter pools average about 120 acres each. Some extensions were made to existing gas pools. The number of oil wells drilled was only one less than in 1943, yet compared with the year 1941, when twice as many oil wells were drilled, the difference is startling. Effective Aug. I, 1944, a blanket subsidy was granted of 35¢ per barrel on all Cleveland-Chatham, Coming, and Lima grades of oil, and 75¢ per barrel on Pennsylvania grade crude. The subsidy was authorized by the Office of Price Administration, with reimbursement to purchasers of the various grades made through the Defense Supplies Corporation, a branch of Reconstruction Finance Corporation. For several years the small operator, particularly the owner of stripper wells, was in a serious position. The subsidy has been a means of real help and, in addition to aiding the operator, it has prolonged the life of many small wells that otherwise would have been abandoned, with consequent loss of daily production and unre-covered reserves. It is questionable whether the price increase is sufficient to revive production of Corning grade, which has

Jan 1, 1945

By George S. Rice

"The successful use of the gas mask by the American Army it France in combatting the poisonous gases of German .shells caused many Army men to feel that the as masks were proof against any kind of gas which might be encountered. The result has been that from time to time there have been reported in the press, deaths of former army men through using their masks to enter various kinds of gases such as illuminating gas, gasoline vapor, and the gaseous atmospheres produced by mine fire. Such a case has just been reported from a mine, in Copperopolis, California, where a former Army man lost his life in descending a mine shaft filled with the fumes of a mine fire. Another man who, in attempting to rescue him, merely used a dust respirator, lost his life also.While the American type of the Army gas mask was developed by the Bureau of Mines for the War Department, and since the war a section of the Bureau's in¬vestigative force has been developing industrial gas masks for certain specificgases, the Bureau has repeatedly called to the attention of the public the fact that such masks have serious limitations and in no case should a gas mask be used in underground workings for the reason that there may be an insufficient amount of oxygen to breathe, (and the gas mask does not supply oxygen) or there may be present carbon monoxide, which the Army mask will not remove, and there always is some carbon monoxide produced by a mine fire or by a coal-mine explosion, or by a blast of dynamite or other explosive.It is true that the Bureau has been developing a mask which may take care of a small percentage of carbon monoxide, that is, one per cent and under, but in mine fires and after explosions, there may be, and frequently is, a much larger percentage of carbon monoxide in the mine atmosphere. Masks such as these, for small percentages of carbon monoxide and associated gases are for use in connection with industrial surface plants, as for example, on the top of a blast furnace or around gas producers in the open air."

Oct 1, 1920

By A. Wahab Khair, S. Jung

"This paper deals with the fracturing process of laterally confined blocks of coal subjected to impact indentation. During the test, blocks of coal with approximate dimensions of 10 in. x 10 in. x 6 in. were laterally confined to predetermined equivalent in-situ stresses and then subjected to an impact indentation by dropping coal cutting bits (various shapes) attached to a known weight from a known height. During the test a number of parameters, namely surface strains (using strain gages), penetration depth (using L.V.D.T.) and acoustic emission characteristics were measured. After the test, the fractured surfaces were photographed with the aid of a camera attached to a microscope. The fracture, its intensity and extended zone within the coal blocks were mapped using sonic techniques. By correlating measured parameters, fractured zones under a given set of test parameters were identified and characterized.INTRODUCTION To improve the understanding of basic failure mechanisms in coal cutting, a better knowledge of fracture and crack regions caused by the indentation in coal is needed. This study reports the detailed experimental procedure used in fracture analysis of indentation experiments on coal specimens using the Acoustic Emission (A.E. hereafter) and sonic techniques. The relationship between microcracking and the inelastic deformation of rock was confirmed by a series of experiments in which the A. E. generated by the cracking in the rock specimen were recorded and the number of events were compared to the strain measurement. (Scholz, 1967).According to fracture mechanism theory, crack initiation in brittle materials such as rocks begins from ""flaws"" either pre-existing or induced by the indentation process itself. Rocks are pervaded by natural cracks and pores, from which numerous possibilities for crack initiation arise (Lindquist, Lai and Alm, 1984)."

Jan 1, 1989

By E. A. Koester

Kansas produced approximately 35,434,000 bbl. of oil in 1932 compared to 37,018,000 bbl. in 1931, a decrease of 1,584,000 bbl. or 4.2 per cent. These figures do not indicate the amount of oil that could have been made available from the state for the year. Many of the fields discovered during the year and some discovered in previous years were entirely shut in. Practically all flush production discovered within the last two years has been prorated in some manner or other. Probation Kansas production is under regulation as specified in House Bill 387, passed by the legislature in 1931, which became effective when published May 28, 1931. The principal features of the law are the prohibition of waste, including gas energy, the regulation and prevention of discrimination of purchasers, the marketing of oil ratably from wells in each field when the daily production is above 15 bbl. per well. This act gives the enforcing powers to the Public Service Commission. The Commission, having many other regulatory duties, appointed an Oil Advisory Committee, which, with the aid of the State Umpire, keeps records and makes recommendation for orders as to specific regulation of fields and conditions in each field. At the time the Commission was given authority to regulate production and marketing in flush fields, several of these had already been under voluntary proration and marketing restrictions by agreement of the operators. These gradually came under the control of the Commission by mutual consent. It is the policy of the Public Service Commission to follow the will of the operators so long as they do not have ideas or plans in conflict with the law. The cost of administration of this law is assessed against the operators according to the amount of oil taken from the fields in which ratable taking is necessary. There is a feeling that the whole state should share this expense, which is small, since it is beneficial to the older fields by assuring them 100 per cent market for their output by restricting the flush fields.

Jan 1, 1933

By Robert M. Becker

The evaluation of in situ rock stresses from measurements of the change in diameter of a borehole that is stress-relieved by overcoring has become a common practice. Generally the stress evaluation has been based on isotropic relations whereas rock in varying degrees is anisotropic. A plane elasticity solution for a circular hole along one axis of an orthotropic medium has been adapted to evaluation of in situ stress. The necessary elastic parameters for this evaluation may conveniently be obtained from static tests on the overcore in conjunction with a consistent orthotropic thick-wall cylinder solution. The method and equations for the laboratory and field evaluations are summarized and illustrated.

Jan 1, 1968

By Pinakin C. Chaubal

An industry ? university consortium was set up to develop advanced tools necessary to understanding of the various phenomena occurring in the hearth of the modern iron making blast furnace. The major driver for this work was to provide the technological support required to extend campaign life of blast furnaces, which, by current agreement is tied to the life of the furnace hearth. The hearth wear is significantly affected by the hot metal velocity, temperature distribution and refractory temperatures. Due to the difficulty in making measurements inside the hearth, novel approaches to gain a fundamental understanding of the detailed physical and chemical processes in the hearth must be developed. The approach used in this project was to develop a 3-D CFD (Computational Fluid Dynamics) model coupled with extensive validation efforts. The CFD model is being utilized (1) to understand the phenomena in the hearth, (2) to understand the impact of changes in the internal conditions of the hearth on wear patterns; and (3) to design a monitoring/controlling system for prolonging campaign. In this paper, the results will be reviewed.

Jan 1, 2006

By C. E. Shoenfelt, E. W. Krampert

The major oil discovery in 1938 for Wyoming was the General Petroleum Corporation's So. 1 Government, C.NW.SE. of sec. 21-35N-77W, on the Cole Creek structure in central Wyoming, 14 miles northeast of Casper. This well found commercial oil production in basal Cloverly sand (Lakota) at 7978 ft. and was completed on May 28, 1938, at 8019 ft., 3 ft. in Morrison shale. It had an initial produrtion of 10 bbl. of oil an hour but at the end of a 7-day test made 336 bbl. of oil in 24 hr. During 1938, the well produced a total of 23,161 bbl. of oil. It has been agitated about 10 days out of each month to provide fuel for lease and drilling operations, the balance of the time it has been shut in pending the completion of the second well on the structure. The Cole Creek oil is of intermediate base and has an A.P.I. gravity of 32.7". The record of the well contains the "tops" listed in the accompanying tabulation. Tops in General Petroleum Corporation's No. 1 Government Well Feet 2210 Top of the Mesa Verde (Teapot sandstone) 2960 Top Steele shale 4500 Shannon sand; good show of oil and gas 6740 Top Frontier sand; some oil saturation 6840 Halliburton test of Froutier did not show much oil, but at 6878 ft. the oil showing amounted to 50 barrels 6878-7051 Shale 7051-7062 Sand with some oil saturation 7062-7920 Shale (sandy phase of Thermopolis shale 7779 to 7788 ft.) 7920-7926 Sand (Muddy); oil-saturated 7926-7974 Shale 7974-7979 Hard, coarse, limy sand (Dakota); some oil saturation 7979-7997 Soft sand; high oil saturation 7997-8002 Shale with pyrites 8002-8016 Sand (Lakota) 8016-8019 Variegated Morrison shale 5600 Elevation Lance Creek Field.—Important extensions to the Lance Creek field in eastern Wyoming were made in 1938 by the completion of a number of

Jan 1, 1939

By C. E. Shoenfelt, E. W. Krampert

The major oil discovery in 1938 for Wyoming was the General Petroleum Corporation's So. 1 Government, C.NW.SE. of sec. 21-35N-77W, on the Cole Creek structure in central Wyoming, 14 miles northeast of Casper. This well found commercial oil production in basal Cloverly sand (Lakota) at 7978 ft. and was completed on May 28, 1938, at 8019 ft., 3 ft. in Morrison shale. It had an initial produrtion of 10 bbl. of oil an hour but at the end of a 7-day test made 336 bbl. of oil in 24 hr. During 1938, the well produced a total of 23,161 bbl. of oil. It has been agitated about 10 days out of each month to provide fuel for lease and drilling operations, the balance of the time it has been shut in pending the completion of the second well on the structure. The Cole Creek oil is of intermediate base and has an A.P.I. gravity of 32.7". The record of the well contains the "tops" listed in the accompanying tabulation. Tops in General Petroleum Corporation's No. 1 Government Well Feet 2210 Top of the Mesa Verde (Teapot sandstone) 2960 Top Steele shale 4500 Shannon sand; good show of oil and gas 6740 Top Frontier sand; some oil saturation 6840 Halliburton test of Froutier did not show much oil, but at 6878 ft. the oil showing amounted to 50 barrels 6878-7051 Shale 7051-7062 Sand with some oil saturation 7062-7920 Shale (sandy phase of Thermopolis shale 7779 to 7788 ft.) 7920-7926 Sand (Muddy); oil-saturated 7926-7974 Shale 7974-7979 Hard, coarse, limy sand (Dakota); some oil saturation 7979-7997 Soft sand; high oil saturation 7997-8002 Shale with pyrites 8002-8016 Sand (Lakota) 8016-8019 Variegated Morrison shale 5600 Elevation Lance Creek Field.—Important extensions to the Lance Creek field in eastern Wyoming were made in 1938 by the completion of a number of

Jan 1, 1939

By Aldo Bellone, Francesca Rossano, Massimiliano Bringiotti

"In 2004 works started for the now completed seven-level automated car park accommodating 480 parking spaces inside the pre-existent “Morelli cave”, located in a strategic area in Naples. Since 470 BC Greeks initiated the growth of the fascinating world of the underground Naples, of which this cave belongs. It seems that once here the god Mithras was worshiped. It’s also became a quarry for tuff extraction and in 1600s it became an aqueduct serving the area. In 1853 the Bourbon Tunnel, a project commissioned by King Ferdinand II of Bourbon to allow easy escape from the Royal Palace in case of riots, was connected to this network of tunnels. The cavern became an air raid shelter during the Second World War, then a deposit of cars and motorcycles in the '50s and' 60s, a disposal area and it has been abandoned in the last 40 years before it’s new utilization. INTRODUCTION Over time, the overcrowding and congestion of major cities’ historic centres has led to seeking spaces underground that can accommodate activities and car parks, as in the case of the Morelli cavity, site of the future car park by that name. Before describing its characteristics, design solutions, and executive problems, it is necessary to introduce the site historically into the broader landscape of the cavities present below ground in the municipality of Naples. The province of Naples, which includes the area of the Municipality of Naples, has a large number of cavities. The existence of “Naples underground” is connected with the morphological and geological conformation of its territory, consisting of tuff stone which has entirely special features of lightness, brittleness, and stability. The first transformations in the territory’s morphology, taking place thanks to the Greeks starting from 470 BC, initiated the growth of the fascinating world of Naples underground. These transformations were dictated by water provision requirements, which led to the creation of underground cisterns to collect rainwater, and by the need to recover construction material to erect the buildings of Neapolis. In subsequent centuries, the city’s expansion led to the construction of a proper aqueduct, which allowed drinking water to be collected and distributed thanks to a series of cisterns linked to a dense network of tunnels. During Roman rule, the existing aqueduct was expanded and perfected, but with the rise of the Angevins in 1266, the city saw great urban expansion, which obviously corresponded with increased extraction of tuff from the subsoil to construct new buildings. This confirmed a particular feature of Naples: that of having been generated from its own innards, with buildings rising directly above the quarry that provided their building material."

Jan 1, 2016

By Yesil MM, Bozdag T

This paper describes the conver- gence and load measurements carried out in inclined seams at five longwall faces, two of which were supported by hydraulic props and the other three by conventional timber supports in Karadon-Gelik mine. The minimum support capacities determined in this study are compared with the results obtained from two empirical approaches suggested by Wilson (1975) and Jacobi (1981). The characteristics of hydraulic props to be used and support patterns in the longwalls are found, conclu- sions are drawn and suggestions are made. Design nomograms are prepared for field engineers, in order to be able to approach the problem more confidently and realistically.

Jan 1, 1992

By Raymond D. Sloan

Dropping from third position among the oil-producing states of the nation in 1942, Oklahoma ranked fourth in 1943 with a total output of 121,431,ooo bbl., a decline of 11.9 per cent from the previous year's total of 137,792,000 bbl. Production ranged from a maximum of 346,900 bbl. daily in February to a low of 322,800 bbl. daily in October, and at the close of the year was averaging 330,000 bbl. daily from 52,096 wells, or an average of 6.3 bbl. per well. The state's well, average at the close of 1942 amounted to 6.7 bbl. At the turn of the year, it appeared reasonable to assume that Oklahoma's producing rate would continue its downward trend during 1944 unless reversed by greater than normal discoveries. To Jan. I, 1944, Oklahoma has produced 5,188,466,-ooo bbl. of crude oil. Development and Exploration A total of 1287 wells was drilled in 1943, representing an increase of 77 wells, or 6.4 per cent over the preceding year's total of 1210. Of the wells completed, 587 (45.6 per cent) were oil wells with an average initial production of 319 bbl.; 127 (9.9 per cent) were gas wells with an average initial of 8,639,000 cu. ft.; and 573 (44.5 per cent) were dry. A total of 333 wildcats was drilled (25.9 per cent of all wells), an increase of 13 (4.1 per cent) over the 1942 total of 320. Of the*wildcats drilled, 46 (13.8 per cent) were oil wells with an average initial production of 235 bbl.; 27 (8.1 per cent) were gas wells with an average initial of 8,249,-ooo cu. ft.; and 260 (78.1 per cent) were recorded as failures. Reconditioning of wells throughout the state led to a total recompletion of 230 wells. Of these, 131 were oil wells with a combined initial production of 8360 bbl., 31 were gas wells with a total initial of 211,950,000 cu. ft., and 68 were abandoned. The 46 successful wildcats opened 33 new producing areas, one of which produced from three separate horizons, and led to the development of production in new horizons in 11 old pools. While none of the 1943 discoveries have as yet developed into what might be termed major pools, the West Moore pool, in Cleveland County, and the West Edmond pool, in Oklahoma County, are the two outstanding new areas opened to production. The West Moore pool, sec. 29, 10 N., 3 W., discovered in December 1943, was completed for an initial production of 248 bbl. of oil in 3 hr. through small tubing chokes in the second Wilcox sand from 8787 to 8800 ft. One well was drilling in this area at the close of the year. The West Edmond pool, an April discovery in sec. 32, 14 N 4 W., is producing from the Hunton lime at a depth of approximately 6950 ft., the world's deepest Hunton lime pool. To the end of the year, 15 oil wells had been completed, with no gas wells and no failures. Accumulated production to Jan. I, 1944, amounted to 474,300 bbl. of 41" gravity oil. There were 29 active operations in the field at the end of the year. The West Edmond and West Moore pool discoveries established the first commercial production west of the Granite Ridge,

Jan 1, 1944

By Raymond D. Sloan

Dropping from third position among the oil-producing states of the nation in 1942, Oklahoma ranked fourth in 1943 with a total output of 121,431,ooo bbl., a decline of 11.9 per cent from the previous year's total of 137,792,000 bbl. Production ranged from a maximum of 346,900 bbl. daily in February to a low of 322,800 bbl. daily in October, and at the close of the year was averaging 330,000 bbl. daily from 52,096 wells, or an average of 6.3 bbl. per well. The state's well, average at the close of 1942 amounted to 6.7 bbl. At the turn of the year, it appeared reasonable to assume that Oklahoma's producing rate would continue its downward trend during 1944 unless reversed by greater than normal discoveries. To Jan. I, 1944, Oklahoma has produced 5,188,466,-ooo bbl. of crude oil. Development and Exploration A total of 1287 wells was drilled in 1943, representing an increase of 77 wells, or 6.4 per cent over the preceding year's total of 1210. Of the wells completed, 587 (45.6 per cent) were oil wells with an average initial production of 319 bbl.; 127 (9.9 per cent) were gas wells with an average initial of 8,639,000 cu. ft.; and 573 (44.5 per cent) were dry. A total of 333 wildcats was drilled (25.9 per cent of all wells), an increase of 13 (4.1 per cent) over the 1942 total of 320. Of the*wildcats drilled, 46 (13.8 per cent) were oil wells with an average initial production of 235 bbl.; 27 (8.1 per cent) were gas wells with an average initial of 8,249,-ooo cu. ft.; and 260 (78.1 per cent) were recorded as failures. Reconditioning of wells throughout the state led to a total recompletion of 230 wells. Of these, 131 were oil wells with a combined initial production of 8360 bbl., 31 were gas wells with a total initial of 211,950,000 cu. ft., and 68 were abandoned. The 46 successful wildcats opened 33 new producing areas, one of which produced from three separate horizons, and led to the development of production in new horizons in 11 old pools. While none of the 1943 discoveries have as yet developed into what might be termed major pools, the West Moore pool, in Cleveland County, and the West Edmond pool, in Oklahoma County, are the two outstanding new areas opened to production. The West Moore pool, sec. 29, 10 N., 3 W., discovered in December 1943, was completed for an initial production of 248 bbl. of oil in 3 hr. through small tubing chokes in the second Wilcox sand from 8787 to 8800 ft. One well was drilling in this area at the close of the year. The West Edmond pool, an April discovery in sec. 32, 14 N 4 W., is producing from the Hunton lime at a depth of approximately 6950 ft., the world's deepest Hunton lime pool. To the end of the year, 15 oil wells had been completed, with no gas wells and no failures. Accumulated production to Jan. I, 1944, amounted to 474,300 bbl. of 41" gravity oil. There were 29 active operations in the field at the end of the year. The West Edmond and West Moore pool discoveries established the first commercial production west of the Granite Ridge,

Jan 1, 1944

By Gilbert P. Moore

Petroleum operations in Bolivia are still limited to those of the subsidiaries of the Standard Oil Co. of New Jersey. Development work is being carried on at Sanandita and at Bermejo and testing operations in the north. Five wells have been completed at Sanandita. Wells 1 and 2 are producers, 3 and 5, which are north of 1 and 2, are poor wells, and well 4, to the south, was dry. In the Bermejo field, well 5 has just been completed. No information as to the production is obtainable. In the north one string was operated at each of the following locations: Machareti, Camatindi and Camiri. The well completed at Machareti during the year was a failure. The result of the others is not known. It is reported on good authority that a pipe line will be completed in 1931 to connect the Sanandita field with the Lomitas field in the Argentine. This will place Bolivia among the ranks of the producing countries of South America for the first time. This development indicates that some arrangement has been arrived at with the Argentine Government for the importation of Bolivian oil. During 1930 the Bolivian Government declared in effect the new Petroleum Law which had been expected for such a long time. One of the first acts of the military junta, which rose to power through a coup d'état, was to cancel this law, so that Bolivian oil operations are still under the old law of 1921. One new local company was formed to exploit 1,500,000 hectares near the town of Cochabamba. The Bolivia Concessions, Ltd., which had a concession permitting the selection of 17,000,000 acres in eastern Bolivia, is reported to have failed in 1930 and is now being liquidated. Chile During 1930 the Chilean Government entered into a contract with an individual to explore in five distinct zones of the Republic. According to the contract, geologists must be at work there by May 1 of this year and a well must be started by the end of 1931. If the operations are

Jan 1, 1931

By Charles W. Carter, Alfred H. Bell

In 1942, Illinois produced 106,590,000 bbl. of crude oil, or 7.6 per cent of the entire amount produced in the United States. It ranked fifth among the oil- producing states. The production for 1942 declined 20.5 per cent from the previous year's total of 134,139,000 bbl. Tie daily average production for 1942 was approximately 292,000 bbl., or 74,000 bbl; less than the 366,000 daily average for 1941. At the beginning of 1942 the daily production was 367,000 bbl. This production declined steadily to 282,000 for June and to 246,000 for December. This steady decline was caused partly by the reduction in drilling resulting from Federal Conservation Order M-68 and partly by the fact that no major pool was found during the year. Discoveries Forty new fields (Fig. 2, Table 2), 48 extensions (Table 3), and 45 additional producing zones in existing fields (Table 4) Were discovered in 23 counties in Illinois during 1942. Of the 40 new fields, three

Jan 1, 1943

By Alfred H. Bell, Charles W. Carter

In 1942, Illinois produced 106,590,000 bbl. of crude oil, or 7.6 per cent of the entire amount produced in the United States. It ranked fifth among the oil- producing states. The production for 1942 declined 20.5 per cent from the previous year's total of 134,139,000 bbl. Tie daily average production for 1942 was approximately 292,000 bbl., or 74,000 bbl; less than the 366,000 daily average for 1941. At the beginning of 1942 the daily production was 367,000 bbl. This production declined steadily to 282,000 for June and to 246,000 for December. This steady decline was caused partly by the reduction in drilling resulting from Federal Conservation Order M-68 and partly by the fact that no major pool was found during the year. Discoveries Forty new fields (Fig. 2, Table 2), 48 extensions (Table 3), and 45 additional producing zones in existing fields (Table 4) Were discovered in 23 counties in Illinois during 1942. Of the 40 new fields, three

Jan 1, 1943

By Francisca San Martín, Martin Rudolph, Willy Kracht, Tomás Vargas

It has been shown that bacteria Acidithiobacillus ferrooxidans can be used to depress pyrite in seawater flotation at natural pH, which opens the possibility for its use as an alternative to lime to depress pyrite in copper sulfide flotation. In order to have a better understanding of the mechanisms involved in pyrite depression with A. ferrooxidans, an exploratory experimental campaign was carried out, including attachment density and contact angle measurements, and the effect of adding bacteria before or after collector. Biodepression of pyrite improves when increasing pH from 3 to 8, with a decrease in recovery from 92% to 36%. This increase in depressing capability is accompanied by an increase in attachment density, from 2.58×108 bacteria/g to 1.99×109 bacteria/g at pH 3 and 8, respectively, suggesting that the mechanism of depression is related to the attachment of bacteria to the pyrite surface. It was observed that the conditioning sequence with collector and bacteria influences the biodepression capacity of A. ferrooxidans. Having as a reference a value of pyrite recovery equal to 97%, when using only xanthate in seawater flotation at pH 8, the effect of both conditioning with bacteria-followed-by-xanthate and xanthate-followed-by-bacteria were assessed. When bacteria were added before the collector, the recovery of pyrite decreased to 36%. On the other hand, when bacteria were added after collector, the recovery was 64%, showing that biodepression of pyrite with Acidithiobacillus ferrooxidans is more efficient when the conditioning is carried out first with bacteria. The contact angle values show that there is little effect of the second component added to the system, i.e., if pyrite is first conditioned with bacteria, the contact angle does not change significantly once the xanthate is added (bacteria-followed-by-xanthate). The same was observed when the conditioning sequence was xanthate-followed-by-bacteria.

Jan 1, 2018

By X Z. Sun, N Jiang, J H. Zhao, C X. Wang, L Y. Bai

In backfill grouting for underground coalmines, the filling materials strengthen the caving rock and support the overlying strata to reduce surface subsidence. The broken roof strata fail and collapse during mining operations without appropriate supporting measures being taken. It is difficult to perform continuous backfill mining on the working face of such roofs using the existing mining technology. Therefore, in order to solve the above problems, fly ash and mine water are considered as filling materials, and flow characteristics of fly-ash slurry are investigated through laboratory experiments and theoretical analyses. Laws governing the diffusion of fly-ash slurry in the void of caving rock masses and in the void between a caving rock mass and a basic roof are obtained and verified. Based on the results obtained from the above analyses and field conditions at the Zhaoguan coalmine, Shandong Province, China, a cave backfill grouting system of the hauling pipeline is developed and successfully tested at the 1703 working face. The results demonstrate that a filling rate of 43.46 per cent is achieved, and the surface subsidence coefficient of the grouting process is found to be 0.475. Compared to the total caving method, the proposed system is found to achieve a reduction rate of 40.63 per cent. This effectively helps in lowering the value of the surface subsidence coefficient. Fly ash and mine water, considered as primary materials in this study, also play a significant role in improving the air quality and water environment.

Nov 29, 2022

By J. F. Bryson

A FULL description of past mining conditions in eastern Kentucky coal mines with reference to the cause of coal bumps and the preventive methods was given by the writer in a previous paper.1 At that time the method had been tried for a period of 13 months, successfully. The method has been enlarged add carried on for over two years, and is still successful. Recapitulating briefly from the previous paper: The No. 3 mine of the Mary Helen Coal Corporation, Coalgood, Ky., operates in the Harlan seam, and is worked by a room-and-pillar method. Cover varies from 1200 to 2000 ft. and the immediate roof over the coal is a hard, massive, sand rock, estimated to be from 70 to 90 ft. thick. The average height of coal throughout the mine is 46 inches. The reason for adopting the method were that in this mine five men had been killed by coal bumps between 1931 and 1934; many other men had been injured and coal-cutting machines had been thrown from under the cut. The morale of the workmen was at a very low ebb. Many remedies had been tried in other mines troubled by coal bumps, one method being to leave chain and room pillars in every 500 ft., to serve a bumping block; the idea being that if a bump took place it would act on the pillars left in the gob. Another method adopted was to board up a pillar, leaving a small opening at the bottom sufficient for shoveling coal. In this system the idea was that if a bump did occur on the pillar, the boards would stop flying coal so that no one would be injured. Many other methods were tried and it is safe to say that each mine troubled by coal bumps tried various remedies, none of which proved effective. On considering all that had been attempted in an effort to eliminate coal bumps, and the information gained by experience of coal bumps in various mines, it was thought that a long face with gob support would eliminate the trouble. Accordingly, on Jan. 15, 1935, a long face was started with wood cribs on 20-ft. centers. When the former paper was written on this method, the long face had been brought back a distance

Jan 1, 1937

By Ellsworth Y. Dougherty, Edwards F. Fitzhugh

"INTRODUCTION During the summer of 1945 the Bureau of Mines made approximately 200 miles of reconnaissance magnetic surveys in north-central Mirnesota. The survey started near the western end of the Mesabi Iron Range and extended into the area to the southwest, west, and northwest and also southward to the-northern limits of the Cuyuna Iron Range. The purpose of the survey was to data to assist exploration for iron ore in the region through:1. Supplying a relatively unit form network of traverses, by which and future surveys of localities in the urea ray be correlated. Suggesting localities in which more detailed magnetic surveys may be justified, and, Disclosing localities in which there is lass hope of obtaining significant results from further magnetic surveys.The instrument used was a Hotchkiss Superdip, and traverses for calibration and comparison were run with a Schmidt-type magnetometer. Field observations and work directly related thereto were carried out under contract by E. J. Lang-year Co., Minneapolis. Engineers of the Bureau of Mines planned, directed, and reviewed the survey."

Aug 1, 1946

By Verne E. Hooker

Stress relief measurements were made at three underground test sites associated with the Henderson project, American Metal Climax, located in the rugged, mountainous region between Loveland Pass and Berthoud Pass on the Continental Divide in Colorado. Sufficient data were obtained to determine the three-dimensional stress ellipsoid for each site. The measurements were made at hole depths greater than one diameter of the mined opening; thus, calculated stresses are representative of premining in situ conditions. The vertical components of stress are in good agreement with overburden depth including the influence of mountain topography. Horizontal components of stress substantially increase with depth. These components are believed to be influenced by stresses presumably of tectonic origin. The largest measured principal stress was 5,900 psi at a depth of 3.708 feet. The predominant orientation of maximum principal stress for the determinations at greatest depth is in the NW-SE quadrants.

Jan 1, 1972