Search Documents

By Joseph F. Davies

To gain knowledge of the actual accident hazards present in Kentucky coal mines, reports of fatalities during 1931, 1932, and 1933 have been analyzed and the pertinent factors included in tables, accompanied by some discussion and recommendations for the reduction of accidents from particular causes. ACKNOWLEDGMENT This study was made possible through the cooperation of John F. Daniel, chief of the Kentucky Department of Mines, who made available department records, in addition to the monthly bulletine issued by his office reporting these fatalities.

Jan 1, 1934

By Guan Jichang

An abandened breakwater, located at the rear of No. 2 berth in Dongdu Port area of Xiamen City, was not cleaned thoroughly when the backfilling of sand started. The uncleaned stone layer was about 2 to 3 meters deep, with the average piece of stone weighing about 1 to 3 kN. A large grain storing house, 220X 60m2 in area, was designed and built at the above mentioned complicated site. The foundation of the grain house are made up of the cast-in-situ piles. It is well known that it is difficult for the submarine engineering drill to go down through such large-sized stones. Having com-pared the various plans, a final decision has been made which involves explosions with small amounts of charge plus cone bit in the enlarging of the size of the pores. Such a method has successfully prevented the pores from slumping and made it possible to fulfill the project without any difficulties. This paper also introduces the ways in effectively dealing with each individual stone.

Jan 1, 1991

By James A. Pendleton

The Legislature of the State of Colorado adopted House Bill 1223, "The Colorado Surface Coal Mining Reclamation Act" (The State Act), in 1979. This Act provided for the creation of a state regulatory program as accommodated within Public Law 95-87, "The Surface Mining Control and Reclamation Act of 1977" (SMCRA). Section 34-33-121(2)(a) of the Colorado Revised Statutes (CRS) and Section 516(b) of Public Law 95-87, identically require the underground coal mine operator to "Adopt measures consistent with known technology in order to prevent subsidence causing material damage to the extent technologically and economically feasible, maximize mined stability, and maintain the value and reasonably foreseeable use of such surface lands, except in those instances where the mining technology used requires planned subsidence in a predictable and controlled manner..." On July 23, 1980, the Colorado Mined Land Reclamation Board adopted regulations to administer and enforce the State Act. Amendments to the Rules, including the subsidence regulations were adopted by the Board in August of 1981. These regulations require the prediction, monitoring and mitigation of "material damage" caused by subsidence.

Jan 1, 1985

By R. L. Blackwood

The solid inclusion cell for absolute in situ stress measurement has been found to give reliable results in coal. The cell is described briefly, along with the methods of installing, overcoring and taking readings in underground coal mines. The validity of the cell performance is demonstrated by reference to the stress-relief curves obtained during overcoring and a three-dimensional B.I.E.M. analysis of the installation to test for stress anomalies deriving from the geometry of the overcoring groove-borehole-cell arrangement. Case studies of two stress measurement projects using the cell are presented for coal mines in New South Wales, Australia.

Jan 1, 1982

By S. N. Zhow

China has at least 200 collieries suffering from the problem of instantaneous outbursts of coal and gas. The strong outbursts often occurred in active tectonic lanes and areas of high stress concentration. In this paper, the author describes some characteristics of the strong outbursts and analyses the effects of ground stress, gas pressure and the properties of coal in outbursts.

Jan 1, 1987

By N. V. Mel'nikov

This paper discusses the reserves of oil, natural gas and coal in the USSR, with particular attention to the future role to be played by coal in supplying the energy fuel resources of the country.

Jan 1, 1972

In an earlier day, a moderate-sized 600 tpd mine could easily require 60 working faces and might use five supervisors. The miner had a tonnage rate as an incentive and was largely his own boss. With the advent of conventional mining machine crews, the typical pattern of resource used changed radically. The number of work places could be cut by a factor of ten, but supervision only by a factor of somewhere around three, or at most, five. Obviously, supervision was increased. Capital use rose at the same time by a factor of approximately eight. Materials used, such as powder and bits, probably in- creased in both quality and unit cost, too. It certainly required a better-trained man to run the machines, but fewer miners were needed. It is clear that each input factor such as land, labor, capital and management, has changed significantly and it would be foolish to attribute all the gain to improved machines. However, concentration of work was a vital consideration in the change, sketched above, and such focusing of work in fewer areas could not have occurred without high capacity mining machines.

Jan 11, 1968

By W. A. Steingraber

This paper discusses the application of deep well disposal techniques to the problem of disposing of large volumes of low level radioactive wastewaters generated by the in situ uranium mining industry in Seth Texas. Data is presented on wastewater composition and volumes, geologic and hydrologic parameters of the disposal reservoirs, tell construction techniques, well operation, well monitoring requirements, and critical factors in evaluating the Safety and environmental impact of a deep injection well system.

Jan 1, 1980

By Matt Manson

Diamonds in Canada: Recent Advances in Exploration Methodology and Advanced Stage Assessment 1. Exploration Methodologies ? Prospectivity Mapping ? Surficial Geochemistry ? Geophysics 2. Advanced Stage Assessment ? Petrology and Diamond Paragenesis ? Micro/Macro ratios and Macro grades ? Value Sampling and Modeling

Apr 1, 2005

By C. W. Langenberg, D. E. Macdonald, R. S. Strobl

"The successful marketing of Alberta coals will increasingly depend, to a large degree, on an extensive coal quality information base. This information, at present, is generally based on a deliverable, cleaned coaland is confined to existing mine sites. Coal quality information is not as well understood for raw in situ coal outside of mine sites and even less is known about the geological factors that control it.If new uses and markets for Alberta coal are to be developed, such as gasification, coprocessing, and exploiting high rank coals for combustion, it will be imperative that the coal quality parameters important for these utilizations be known. These parameters need to be known for existing deliverable coals and, just as important, for as yet unexploited in situ coal. Factors such as the Cl, No, K, Co, P and trace element contents should be addressed to meet the requirements of these new utilizations.The geological characterization and explanation of what factors control these coal quality parameters is part of research being done at the Alberta Geological Survey. In-seam vertical profiling has been undertaken within the plains and foothills/mountains coals to determine exactly where coal quality variations occur and why. In the Ardley coal zone at the Highvale Mine it has been found, for example, that the ash content of the mined coal is made up of discrete partings and of microsized particles associated with inertinite macerals. The in-seam characterization of coal seams will lead to a better understanding of in situ coal quality variations, leading to new uses and markets for Alberta coal."

Jan 1, 1993

By B. J. Vorster

AngloGold South Africa region currently consists of twelve gold plants. These plants use a combined total of $20 million of cyanide per annum. Of this, the major portion (60%) is consumed at two Ergo dump retreatment plants. Historically the primary motivation for cyanide control at Ergo has been one of leach/cost optimization. However, more recently, with the increased public awareness of cyanide in the environment, a secondary but increasingly important motivation for control has been to ensure that only the minimum amount of cyanide is added to the process whilst not compromising leach performance. Following a brief overview of the Ergo process, the methodology in determining the amount of cyanide to be added is described. The paper then traces the developments in cyanide control from very basic manual systems to the current automated control system. In line with the increasingly sophisticated control systems, developments also took place in regards to the method of cyanide analysis. The development of these analysers is also discussed. Whilst cyanide is one of the major drivers, if not the major driver of gold dissolution, it cannot be viewed in isolation particularly with respect to the relationship between cyanide and oxygen as ascertained from the Elsner?s well-known equation. Consequently, in order to control cyanide addition, knowledge of the relative cyanide/oxygen profiles is necessary. Various means investigated at Ergo for pulp oxygenation have therefore been included for the sake of completeness. Finally a comparison is made of the control achieved from the current system compared to the original manual system. The knowledge and experience gained at Ergo is now being used to draw up guidelines for the installation and optimization work at the other AngloGold plants. The net effect of this will be reduced cyanide consumption for the region, which also, apart from the obvious economic benefit, translates into a reduced environ-mental risk.

Jan 1, 2001

By Ismet Canbulat

The cut out distance in the continuous miner sections in South African collieries is limited to 12 m. However, this distance can be extended to 24 m by the permission of the Department of Mineral and Energy (DME). This paper investigates the risk of roof Calls associated with the extended cut out distances permitted by the DME. Extensive underground experiments have been conducted using sonic probe extensometer under various geological conditions to identify the effect of cutting distance and tinge on the stability of the workings and the performance of the support. The results showed that that the most critical parameter with respect to ground control aspects of extended cut out distance is the bord width, which determines the amount of deformation that will take place in the roof. This was confirmed by the numerical modelling. The results also showed that a significant portion of the maximum deformation in the roof takes place before the ratio of cut out distance to bord width exceeds two. This indicates that once the face is extended more than twice the bord width, the roof will stabilise, assuming that no geological discontinuity is present and that there will be no further geometrical changes in the area as a result of for example the development of an intersection.

Jan 1, 2000

By D. G. C. Robertson

Counter-current staged reactors offer several advantages over batch reactors for mass transfer between two phases. Several metallurgical reactor designs have utilized the counter-current principle, e.g. the WORCA and QSL processes. But before the principle can be widely adopted, it will be necessary to overcome several significant problems. These include the need to minimize longitudinal mixing in a single reactor or to use several separate staged reactors and to carry out different reactions in sequence, e.g. phosphorus oxidation and sulfur reduction. Theoretical and experimental approaches to these problems will be discussed in the paper.

Jan 1, 1988

By C. C. RAE

The Texas Panhandle produced 18,677,000 bbl. of oil in 1932 as against 25,064,000 in 1931. The decline was caused by smaller market demand, since the Railroad Commission potential increased from 105,528 to 149,260 bbl. during the year. Well Completions, 1932 The development during 1932 compares with 1931' as follows: Year Wells Drilled Dry Holes Gas Wells Oil Wells Initial Pro- duction, Bbl. 1931 200 6 77 117 347 1932 136 18 28 90 603 Crude oil prices, small market demand, and lower allowable rate of production caused less drilling. Expiration of leases was one reason for a greater number of dry holes through forced drilling of questionable areas. The small number of gas wells reflected the influence of the business depression upon industrial and domestic gas demand, together with difficulties of franchise negotiations or pipe line extensions under present conditions. Probably much of the gas-well drilling was done on expiration leases, or to protect against drainage, and equalize withdrawals as between the various units held by each gas pipe line company. The increase in average initial daily production was due chiefly to excellent granite wash wells in the LeFors district developed by the Texas Co. and Skelly Oil Company. In the Panhandle district, comprising a major anticline with almost a million productive gas acres, the pools tend to merge in time, the development being confined to more productive areas. Hence separation into pools becomes a matter of time of development with some effort to keep dolomite, archosic and granite wash production separate. Many pools, like the Finley and Bowers, have mainly one type, but many leases and even individual wells produce from two zones. The oil production is usually closely associated with sea level, where proper porous formations

Jan 1, 1933

By Danilo Zim, Matheus Paschoalino, Denis Guimarães, Jasbir Gill

The shortage of water supply in some regions of the globe is particularly problematic and forces mining companies to adopt alternatives like pumping sea water from the ocean up to the mining sites. Although deaeration of sea water or the use of lined pipelines are known options to prevent corrosion during pumping, a recent development of a new corrosion inhibitor allowed the use of simple mild steel pipelines for this purpose. The objective of this study is to demonstrate the recent advances of this technology in protecting against not only general corrosion but localized corrosion, main cause of corrosion-related pipeline failures. Corrosion studies were carried out using electrochemical techniques, weight loss balance as well microscopy surface analysis in order to measure and therefore evaluate the treatment efficiency. The right dosage of corrosion inhibitors may vary depending on water composition and characteristics of each system. Differences were observed depending on the sea water source. Pretreatment of metallic surface impacts the observed corrosion rate which can be as low as 3.6 mpy. The absence of pitting or localized corrosion was achieved in aerated seawater.

Jan 1, 2014

By S. L. Hoyt

IN technological studies on steel considerable emphasis has been placed on the identification of the foreign inclusions, testimony of which is adequately given in the metallographic literature covering methods for their identification. The outstanding accomplishment in this field is the scheme devised by Campbell, Comstock and Wohrman for identi-fying various oxides, sulfides, silicates and other constituents by syste-matic etching tests and microscopic examination.1 The time involved in carrying out this procedure has led to attempts to secure quicker methods, or at least to shorten the time required to secure essential information. An example of this is the use of dark field illumination, but when this was tried out by the authors it was found that cavities and pits on the polished surface appeared bright on a dark field and could not be distinguished from small glassy inclusions. Still another means is the Leitz Ultropak, an instrument equipped with optical units for the illumination of the specimen by reflected light to secure an effect similar to dark field illumination. The structures are made visible in exceedingly sharp details by utilizing the inherent properties of the samples, such as refractive index, absorption coefficients and reflection powers. We have had no experience, with the Ultropak, but a recent paper by Benedicks and Löfquist3 describes methods for

Jan 1, 1934

The quality of the external water source for a mineral processing plant may influence the extent to which the environmentally desirable practice of recycling of water from plant products is possible. This is particularly likely for froth flotation plants where the chemical quality of the water may affect the plantÆs performance. The quality of the external water source or the recycled water can be improved by a water treatment step, and in turn the extent of recycling which can be tolerated is able to be influenced. The quality of the external water can range from very high quality, soft water derived from melting snow, to poor quality, hard water (high levels of dissolved calcium and magnesium) from underground aquifers, and to even lower quality sea water (very high levels of dissolved species including sodium chloride). It can be noted that some underground water is more saline than ocean water as well as containing high levels of dissolved calcium and magnesium. Occasionally, a different source of water is utilised in the wet and the dry seasons. Increasingly, sewage water from cities is becoming a potential external water source with sustainability implications. If the initial quality of the external water is high, the scope for recycling of water from all the products is maximised. Such reuse or recycling of water from the products allows chemical species from oxidation of the ore and from other inputs to the process such as reagents to increase in concentration in the water returned to the plant. Such accumulation of species can have negative effects on the performance of a process such as froth flotation but instances of positive effects exist. Some reagents which are used in flotation plants such as lime or sodium carbonate also happen to be commonly used for independent water treatment plants. Hence, the flotation process may inadvertently provide some aspects of water processing. Where the quality of the water in the feed to a mineral processing plant (external water plus recycled water) is not an issue, more powerful solid-liquid separation processes can be considered to maximise the removal of water from the products and its reuse. Such processes may also have complementary benefits in a sustainable mineral industry by, for example, producing a tailing stream with a higher per cent solid value which is more suitable for safe storage on the surface or underground. This paper documents findings on the effect of water quality on the flotation process. It also considers current directions of change in the need for increased removal of water from plant products. It then considers the implications of these trends for maximisation of water recycling by such operations.

Jan 1, 2003

By Gang C, Changyi S, Liangde G

Geophysical and geochemical methods and techniques for gold exploration and their applications in China are summarised in the paper. Some case histories are also presented. The effect of prospecting for gold deposits using these methods is well illustrated through these examples.

Jan 1, 1997

By Merete Tangstad, Ragnar Tronstad

Ferromanganese production in electrical furnaces is quite an old process. However, as the furnaces are getting bigger, the requirements of cost, yield, product quality, emissions and security are raised. With the increased expectations, the fundamental knowledge must follow. Within the last 25 years there has been a great effort both in the industry as well as the academic environment to push the limits of this process. This article will show some examples of improvements within fundamental data, reaction mechanisms and emissions over this time period.

Jan 1, 2014

By Kathleen M. Kowalski, Audrey Podlesny

The Maslach Burnout Inventory (MBI) was administered and scored for 154 Mine Safety and Health Administration (MSHA) employees kom the US Department of Labor. These employees serve as accident investigators for serious accidents and fatalities as part of their job duties. During a workshop on stress designed for them, subjects volunteered anonymous written anecdotes, confirming and illustrating the findings. The subjects represented locations across the USA and all mining commodities: coal, metal, non-metal, stone, and sand and gravel. The Maslach Burnout Inventory assesses three aspects of experienced burnout: emotional exhaustion, depersonalisation, and reduced personal accomplishments. The average results of the scores for each of the three subscales for the study group of MSHA accident investigators fell in the moderate range. These scores show that the subject population was at some risk for emotional exhaustion and depersonalisation, tending toward burnout. The group evidenced a lower sense of personal accomplishment in their jobs, indicating a higher risk for burnout. From this outcome accident investigators may be at moderate (note: this does not mean average) risk for burnout. The authors recommend follow-up with this population - specifically in training to work with grieving families; and greater organisational support for the accident investigators in this area would be appropriate. Keywords: Burnout; accident investigators; occupational safety and health; job stress.