Search Documents

By E. J. Jacques

A typical problem in ventilation networks with multiple fan systems is the possibility of them interacting. Multiple fan systems are no exceptions in complex tunnels, and may also be met in mines where underground fans are installed. When aiming at controlling a multiple fan system in a ventilation network, e.g. with a view to maintaining an acceptable air quality level, yet at minimum power consumption, transient flow conditions frequently occur. Although in most applications these transients are short compared to the time needed to achieve the planned actions on the ventilation, one should, however, keep in mind that it is important to avoid any bouncing effect between different (adjacent or distant) fan systems. Therefore a simulation of the unsteady-state flows could allow us to learn more about the propagation of transients within the network, and their possible secondary effects Among others, one question that often is raised, is to find out in which sequence and at what time schedule each of the fans in a network should e.g. be started up? Another typical problem, into which an unsteady-state simulation could provide some insight is the following: how should the facilities of variable pitch angle and/or changeable RPM of several fans operating in parallel be handled and combined in order to obtain a flow rate that changes gradually from zero to its maximum value i.e. the sum of the individual throughput flows of all the fans. The literature is not very abundant on the topic of simulating transient flows in networks. There is no doubt that numerical models have been developed (Pollak, Christensen, 1987), most of the time for particular applications (Wala, Kim, 1985), (Tanaskovic et al., 1984), (Schultz, Sockel, 1991), etc. The aim of this paper is to present a model that also simulates one-dimensional compressible flows in unsteady-state conditions with, however, the specific intent to handle networks with more than one fan. PROBLEM STATEMENT The mathematical model chosen to describe the unsteady flows in a ventilation network is based on the dynamic and continuity equations applied to each of its airways. The following basic assumptions are made : - the flow in the airway is considered to be one- dimensional, - - the flow is assumed to be fully turbulent, and hence the ATKINSON equation for calculating the friction losses will be applied. Whether this equation remains valid for transient state flows remains an open question. However, this may reasonably be assumed since the interesting flow frequencies are low. A discussion may be found in (Kämpf, 1987) ; - the airways are assumed to have a constant cross- sectional area along their length. If obviously this would not be the case, it is always possible to subdivide the concerned airway into sections for which the previous assumption holds. Applying the basic equations of mass and energy conservation, the flow in each branch may be described by the Euler equation for Newtonian flows.

Jan 1, 1995

By J Wheeler

The benefits of fine size separation in magnetite concentration are detailed focusing on published research from various iron ore producers. Basic principles of fine sizing and advancements in screening technology are addressed. A chronological review of research is used to show the evolution of fine sizing applications in the industry, starting with studies that demonstrated the benefit of using fine screens to produce consistent lower silica concentrates, followed by improvements in fine sizing equipment that have made effi cient screen classification in ball mill circuits practical. Case studies are used to demonstrate how positive sizing with screens can be used to significantly shift concentrate ‘grind/grade’ relationships.

Jul 11, 2011

By D. A. J. Swinkels

The problem of determining oxygen levels in liquid steel to aid in deoxidation control has received general attention for a number of years. Work in this direction started at the B.H.P. Central Research Laboratories early in 1967 with an evaluation of sampling techniques followed by vacuum fusion analysis to determine the oxygen content of the samples (1). It was found that these techniques had a number of drawbacks if they were to be used for deoxidation control. The method of analysis was rather too slow to allow effective control and measured total oxygen level rather than dissolved oxygen. Furthermore, the results were found to be very variable due to slag entrainment in the samples. Attention therefore turned to the galvanic cell method using a solid oxygen ion conductive electrolyte such as cubic stabilised zirconia. The ionic conductivity properties of electrolytes such as (ZrO2) 85 (CaO).15 had been studied by a number of investigators and had already been applied to the measurement of oxygen activity in gases, in lower melting metals such as copper, lead, tin, silver, alkali metals and indeed the first studies in steel had been made (2,3). Since then the results of a number of studies in the development of an expendable oxygen probe for steel have been reported (4-9).

Jan 1, 1972

By D. F. Kaufman, H. R. Spedden, A. M. Gaudin

MANY studies of comminution have been made to ascertain the size distribution of the product and to evaluate the work of comminution in the light of the size distributions of the feed and product. Up to now, these studies have been essentially statistical in character, that is, a certain lot of feed was subjected to comminution in some specified way, and the aggregate product was fractionated into sizes, thereby losing all knowledge of individual relationship of feed to product pieces. Radioactive tracers offer a means to do something in this respect which could not be done before, namely, to follow the rupturing of some particular piece in its normal environment of other pieces. That is, it permits going beyond the usual statistical limitations of size distribution studies to what may be termed a personalized or individualized study. The purpose of this paper is to present some preliminary experiments conducted with this tool. The method employed was to mark radioactively some constituent of a feed. It is possible, of course, to consider the preparation of two lots of material of which one is radioactive and the other is not, and to blend the two ahead of the comminuting step; but to do so is open to the objection that the two preparations may not be identical. Therefore a technique has been chosen that removes this objection by merely taking out a size fraction of a comminution feed, rendering that fraction radioactive by exposure to a neutron flux, and then by returning it to Table I. Size Distribution of Offspring Albite Particles Originally 28/35 Mesh and in Admixture with Other Sizes After Grinding 2 min in a Steel Ball Mill Specific Activity ' Cumu- Corrected Distrl- latlve Size for Back- butlon In Distri- Fractlon ground, Weight, Product, button, of Product, cpm/gm g Pctb Pct Mesh (A). (W) (P) (ZP) + 28 0 56.0 0 100.1 28/35 62.6 54.0 24.8 75.3 35/48 62.8 59.4 27.7 47.6 48/65 41.1 53.0 16.2 31.4 65/100 29.6 45.7 10.2 21.2 100/150 23.7 37.0 6.6 14.6 150/200 23.3 25.1 4.4 10.2 200/270 20.1 19.0 2.9 7.3 270/400 17.8 21.2 2.9 4.4 -400 22.9 25.2 4.4 — 100.1 a These activity determinations were made in rapid succession in the order given. The specific activity (Ao) of the active 28/35 mesh fraction of the feed was measured at the beginning, after the measurement on the 65/100 mesh size fraction of the product, and; The end. The decay-corrected activities at those times were 246.7, 241.0. and 236.9 cpm per gm. The weight (W0) of the active 28/35 mesh fraction in the feed was 55.0. b Example of calculation for P in the 65/100 mesh oroduct frac- A W tion; A = 29.6, W = 45.7, Ao = 242.7, Wo = 55.0: P = — x — Ao Wo = 0.102 = 10.2 pet. the remainder of the charge for the comminution experiment. A relatively simple procedure was developed by which albite, containing sodium, was activated in the M.I.T. cyclotron. The cyclotron makes highspeed deuterons which impinge on a beryllium target, thereby producing a concentrated neutron flux. The mineral was exposed to this flux for 2 hr. This treatment changed enough of the sodium to sodium 24 (14.8 hr half-life, 1.4 mev ß) as to make detection and measurement easy. The nuclear reactions taking place were: 11Na23 (n,?) 11Na24 (irradiation) 11Na24 ß,?,? 12Mg24 (decay) The detailed technique of the experimentation was as follows: 40 kg of hand-sorted, lump albite were crushed to pass 10 mesh. After careful mixing of the lot, a screen analysis was made. The whole lot of material was fractionated on standard Tyler screens from 14 down to 200 mesh. Samples for experiments were compounded from these fractions in accordance with the screen analysis. When it was desired to make an experiment in which, for example, the 28/35 mesh size fraction was to be studied, the blend of size fractions was made as indicated above, except that the 28/35 mesh size fraction was added only after irradiation in the cyclotron. The blended charge containing the activated albite was ground for 2 min in a laboratory ball mill with a steel ball charge of controlled size distribution. The ground product was carefully sized on a set of Tyler screens in a Ro-tap. Each size was analyzed for radioactivity by the use of an end-window Geiger-Mueller counter and standard scaling circuit. This analysis was carried out in detail as follows: a 20-g sample was placed in a Petri dish, packed carefully to obtain reproducible geometric distribution with reference to the Geiger-Mueller tube, and the activity was counted for a 2-min period. Several determinations of the activity of the active size fraction in the feed were made at various times to establish the decay in activity with time. Linear interpolation was used to evaluate the activity that the active size fraction in the feed would have had at any given instant. The ratio of the observed activity in a size fraction of the product to the activity that the active size fraction in the feed would have had at the same time gives the fraction in the product size that came from the irradiated size in the feed. The general formula for finding the distribution, P, of a specific individual size fraction in the feed

Jan 1, 1952

By John McCaslin

ONE of the most common technical terms in the U. S. today is automation-a word not listed in the 1946 dictionary. The influence of automation on the national economy has been tremendous. It has even been the subject of congressional investigations. Automation, writes Aronson, substitutes mechanical, hydraulic, pneumatic, electric, and electronic devices for human effort and decision? Automatic devices and instruments are used extensively in some industries, but many others have yet to take full advantage of these great discoveries. The petroleum industry has been a leader in using automatic controls-some refineries are almost completely controlled by automatic devices. The field of geophysics is entirely dependent on instruments and has progressed at almost exactly the same rate as improvements in instrumentation. In metallurgy and mineral dressing use of instrumentation is increasing very rapidly. Mining engineers throughout the country are beginning to think in terms of instruments and controls.

Jan 3, 1958

By H. W. III Straley

SOME ten years ago the writer1 made a survey of college catalogues to determine what sort of training geologists were receiving in basic sciences. In the light of this compilation and subsequent experience, he made the statement at the 1939 meeting of the Institute that apparently only in schools offering a curriculum in geological engineering or in the geological option of mining engineering curricula could geologists hope to receive the training advocated by Hubbert.2 In the former study, schools of engineering were excluded because the preparation was known beforehand. The present study aims to consider engineering schools in an effort to determine not only what basic studies are required but what use is made of them in geological courses of the third and fourth years. The present study combined the method of consulting catalogues with a questionnaire. Letters were mailed to officials responsible for supervision of mineral industries curricula requesting information on: (I) the extent to which the engineering preparation of the first two years is actually used in the work of the last two; (2) the extent to which the engineering of the last two years is used in courses in geological engineering or geology; and (3) whether geologists or geological engineers teach descriptively or analytically. Both methods of securing information are open to criticism; the former on the basis of the incomplete information supplied by university catalogues concerning prerequisites and curricula and the latter on the ground that the questions may be phrased poorly or given insufficient consideration by replying officials. Fifty-six questionnaires were mailed and 39 (70 per cent) replies were received. Of the replies, 6 (11.3 per cent) were from colleges of liberal arts unconnected with engineering schools, 11 (20 per cent) were from schools having curricula in geological engineering and 22 (39 per cent) were from departments of mining engineering. The number of replies and their distribution were satisfactory in spite of the receipt of only six from liberal arts colleges. It should be understood that the universities of which the catalogues were examined were not necessarily the same in both compilations. No departments that are admittedly or known to be acting solely as service departments were recorded in the second study. Table I shows that all professional schools require mathematics through calculus, whereas only 7 per cent of the liberal arts curricula expect the same level of preparation; only 73 per cent require trigonometry and 40 per cent college algebra. The proportion of geological engineering curricula requiring differential equations is higher than mining. All of the engineering schools require general and analytical chemistry, whereas only 77 per cent of liberal arts curricula require general and 18 per cent analytical. Twenty-two per cent of the mining and 40 per cent of the geological engineering

Jan 1, 1941

By L. Gutierrez, J. S. Castro S. Laskowski

Water is a medium in which flotation takes place, and flotation efficiency is highly dependent on water quality. Of the total water resources on Earth, less than 2.5 percent is fresh water. This water is used in agriculture, by households and by industry. Among the industrial users of fresh water, the mining industry occupies an important position. Furthermore, mining operations are often located in arid areas with very limited access to fresh water. The demand for and shortage of water in these parts of the world, such as the Atacama Desert in Chile, makes the use of seawater by the mining industry the only sustainable solution. 

By Harry Elkin

Control of coal dust has long been an important aspect in the conventional mining of coal; the main reasons being from a health and disaster standpoint. With the advent, of mechanized longwall mining, the control of dust has required more attention due to the high extraction rate common to most longwall systems. The purpose of this paper will be to describe the dust abatement activities of the longwall operation at Sunnyside. Kaiser-Steel Corporation has three mires located at Sunnyside, Utah, with a total production averaging 6,800 tons of clean coal per day. Of this 6,800 tons, 71 % is mined with continuous miners, the remaining 29% coming from one longwall unit located in No. 3 Mine. Our first longwall panel was started in November, 1961. In October, 1966, we started mining our seventh panel. The present panel is located in the Upper Sunnyside Seam which averages five feet in thickness, but does get as low as 51 inches. The seam pitches 5.5% in this vicinity. The roof is generally good and is comprised of 10 inches of shale cap rocs overlain with sandy shale and sandstone. The floor is sandy shale and is quite undulating in nature. The present panel is 3,800 feet in length with a face of 670 feet. The major equipment employed on our longwall unit is a 125 H.F. Anderton Shearer-Loader, British Jeffrey Diamond armored conveyors and a Dowty self-advancing-roof support system. The Anderton Shearer in use on our longwall unit has a 60" diameter x 27" cutting drum. During the shearing cycle, it traverses the face at 20 feet per minute with a cutting rate of 7.5 tons/minute.

Jan 1, 1967

By T. H. Janes

"IntroductionSULPHUR is a constituent of many industrial products. It is part •of almost anything we eat, wear, or use. In fact, sulphur is so important that there has been an increasing tendency in recent years to measure industrial growth in terms of sulphur consumption.The uncertainty of obtaining adequate supplies •of elemental sulphur from the Frasch-mined domes. of Texas and Louisiana in the United States led all countries in 1950 to seek alternative sources of supply of this necessary element.Canadian industry has been supplied, for many years, with most of its sulphur requirements by United States Frasch-mined sulphur. World demand for this sulphur has necessitated the imposition of controls on its distribution, as production has not kept pace with demand. Until the third quarter of 1950, Canadian manufacturers of pulp and paper, heavy chemicals, explosives, and textiles •experienced little difficulty in obtaining their needs of elemental sulphur from the United States. However, at that time, low producers' stocks and declining reserves threatened to reduce shipments from producers, with the prospect of a continuing shortage for some time. These conditions, together with higher prices, stimulated the search for alternative sources of supply in Canada."

Jan 1, 1952

By Smith I. T

Mine operators have long recognised that the results achieved in primary blasting are critical to subsequent mining activities. With the introduction of "in the hole" drills under- ground and the advantages offered by the use of water gels in conjunction with ammonium nitrate-fuel oil (ANFO) explosives, new mining methods have been developed and enabled improvements in older methods. Pumpable water gels have been used with varying success underground. These gels allow a high loading density even in ragged bore- holes. The problems encountered with slumping in upholes is recognised so the current trend is to use these gels in downholes where wet holes are prevalent. Cartridged water gel technology has advanced to the point where it has allowed the replacement of nitroglycerin (NG) based explosives and pumpable water gels. Today, gels can be made as a tampable product for use in development headings or as a slump- ing product for downholes to give an effective coupling. With the introduction of the Tovex« pneumatic loaders, the problems associated with a pumpable gel were eliminated and gave the user the ability to alter his loading density.

Jan 1, 1977

By F. Woller

The territory of Czechoslovakia is well endowed in deposits of a variety of industrial minerals. At present, 29 different types of industrial minerals are mined from some 600 individual deposits in Bohemia and Moravia only. About half of those production centres involves structural materials like aggregate and common brick clays and loams. A significant proportion of industrial minerals produced in Czechoslovakia are exported. Destinations of main products are shown in Figure 1. Production of industrial minerals in Czechoslovakia has a long history. Glass has been produced since the 14th century, sulphuric acid since 1578, graphite since 1750, and chinaware since 1790, to name just a few; but most of the present production comes from deposits developed during the past forty years. For a variety of reasons, only about 30 per cent of registered and explored industrial minerals deposits in the country are in production (Table 1). Two of the reasons may be the complexity of processing or conflicting interests of parties involved, but lack of market research, investment funds, or processing capacity have also had an impact on the level of utilization of the resource base.

Jan 1, 1992

By H. Colijn

The ever increasing price of bulk commodities forces buyers and sellers in world markets to take a more careful look at methods for obtain¬ing accurate accounting of commodity trans¬actions in commerce and material utilization in processes. Depending upon the application of a sampling and weighing system or the use intended, inaccuracies can result in an eco¬nomic loss of income or a loss in quality of the process. It inevitably results in a loss of control of ones costs. The accuracy of samp¬ling and weighing systems is today extremely important, as they are recognized to be the key components of the overall management system designed to provide both quantitative and qualitative control. This paper will be confined to the weighing systems only and will deal with various as¬pects of system design, calibration and opera¬tions. Special emphasis will be placed on new developments and requirements in this field.

Jan 1, 1988

By George Smith

THE discussion of production control at the Insti-tute's annual meeting was profitable in that it started some thinking. One pertinent question there raised was how the opening of new mines, whose now unneeded output would inevitably react on prices, could be postponed until the market was ready to ab-sorb their output. In transportation some restraint is being exercised on building new and unneeded fa-cilities, but in production no general solution of the problem has been offered. Yet in a special field of new development of increasing importance a quick and easy solution has been suggested. I refer to the leasing of mineral deposits on the public domain. The report of the United States Coal Commission says: "In its possession of approximately 60,000,000 acres of public coal lands the Federal Government has its own responsibility in restraining overdevelopment. The Department of the Interior, which has control of these lands under the leasing law, construes the law as giving the department no discretionary right to refuse applications for leases regularly made by qualified citizens or corporations for coal deposits on the pub-lic domain. It presumes, that the applicant believes there is a need for an additional coal mine in his local-ity and expects to find a market for the coal produced. Overdevelopment, however, is a fact in the West as well as in the East, and wherever present involves needless investment and excessive costs of operation. Plainly, the leasing law should be so amended as to give the executive department full discretion in its approval of the opening of a new coal mine on the, public domain, making that approval contingent on the showing that the new mine would serve the in-terest of the consuming public." A similar view of the Federal Government's re-sponsibility in restraining overdevelopment of its oil lands has been presented by the Federal Oil Conser-vation Board. The leasing law vests little or no dis-cretion in the Secretary of the Interior, who must grant a lease to a qualified applicant regardless of any obvious country-wide condition of surplus produc-tion. This wide-open invitation to exploit and dissi-pate the people's own oil resources could be restricted by simple legislation, although as remarked by the board, such a legislative remedy for a plain economic ailment "does not evoke popular support when its purpose is avowedly to put the brakes on development of natural resources."

Jan 5, 1928

By Ronald I. Fuller

Core Laboratories, a division of Western Atlas International, maintains laboratories in all energy-producing areas of the United States, as well as in many foreign countries. Central to laboratory operations has been the incorporation of computers and computer software. Core has developed a mu1tiuser Laboratory Information Management System (LIMS) , which is currently installed in numerous company sites in the U.S., and is now undergoing installation in Canada. In addition, Core has provided custom soft ware to contract laboratories which Core operates on behalf of mining firms. The software development was done under the direction of the author in Denver, Colorado, and Casper, Wyoming. The intent of this paper is to pass some of the practical experience gained by our efforts on to those who wish to utilize computers more fully in the laboratory setting. The product of analytical laboratories is numbers. Nothing else comes from our work. We deal in information about samples. It is then reasonable to assume that the computer would be central to a laboratory operation. The hard part is to initially define what kind of computer the lab operation needs. The choices today can be very complex, and almost every hardware salesman is full of bad advice. Even the people in your own information services department may hold divided opinions. Since the advent of the personal computer, we have lived with a polarized data processing community. The PC boys consider their machines equal to any challenge, while the "save the mainframe" crowd view the PCs as limited toys that are only good for the things that clutter up a real computer. Management tends to lean toward whatever costs the least.

Jan 1, 1989

By G. Sachs

X-RAY analysis and single-crystal study have been utilized in recent years as a new means of following constitutional changes in alloys. If such transformations can be suppressed by rapid cooling, they can be followed at room temperature in a particularly convenient manner. In the following we shall consider changes in solubility and polymorphic transformations with particular reference to phenomena of the age-hardening type. Finally a thermodynamic viewpoint is developed for examining such transformations.

Jan 1, 1931

By J. A. Benell

DIOXIDE of silicon, commonly called silica, is one of the greatest single constituents of modern in-dustry. It is brought most clearly to the mind when we consider the various kinds of sand and their rela-tion to industry. The major portion of.all sand is silica, and should be its principal component part in building materials. As an abrasive for cutting, polish-ing and sand-blasting, sand serves a vital purpose in many industries. Even lumber is now being sand-blasted, to cut away the softer grains of wood, leaving the harder grains in relief. The result not only in-creases the beauty of the wood, but adds to it an ap-pearance of antiquity. The common uses of silica in industry may be classified about as follows: Chemical industries-filtering medium; manufacture of carborundum; manufacture of water-glass. Paint-inert extender. Mineral fillers-wood filler; filler in rubber, hard rubber, pressed and molded goods, phonograph records.

Jan 5, 1928

By Carroll Wegemann

THAT Colorado was producing oil and gas before the fields of the Mid-Continent were discovered is a fact too frequently overlooked. As early as 1862, oil was obtained in the Florence district (see Fig. 1) from seepages and shallow holes. The first well that could be regarded Fig. 1. as being truly commercial was drilled in this field in 1876. The field is now producing 100,000 bbl. per year, and is credited with a total production of approximately 11,000,000 bbl. The small field near Boulder, Boulder County, was opened in 1901; production has now practically ceased but the field is credited" with a total production of 610,000 bbl. Oil was discovered at Rangeley in 1901, and the field supports a small local refinery at the present time. The first shallow well in the White River gas field was drilled in 1892, and the wells now producing have been

Jan 3, 1925

By E. P. Pfleider, W. D. Lacabanne

ROTARY-percussive drilling is a new method of drilling hard rock. Designed to give variations in thrust, revolutions per minute, and torque ranges, these drills combine the high efficiency of the rotary system in soft rocks with an increasing amount of percussive action in rocks more difficult to fragment. Fundamentals of the rotary, percussive, and combination systems have been described in detail in various papers-most recently by C. Fairhurst and W. D. Lacabanne1-but there is still much basic work to be done on the interplay of actions in the rotary-percussive system to enable the drill designer to achieve the highest efficiencies. Whereas the original units struck light blows of only 15 to 30 ft-lb, adequate for medium hard rocks, the present trend is to piston blows of 50 to 65 ft-lb in order to cope with the granites and other rocks having Shore hardnesses of 75 or more.

Jan 7, 1957

By Paul F. Richardson

Liquids containing suspended solids are encountered in most mineral processing applications. Solids levels cover a very wide range, from ppm levels in cooling water systems to slurries containing greater than 70% solids. When the aqueous phase is recycled or further processed, a solid/liquid separation process is used. Chemical additives used to carry out this process are called coagulants and flocculants. In other cases, one seeks to control or modify the properties of the suspension. Dispersants are chemicals used to aid in suspending solids in a liquid as well as to control the properties of the resulting suspension. Dispersants find a range of uses in mining and mineral processing such as scale control, filter aids, flotation aids, and slurry viscosity modification. Materials used as dispersants include inorganic salts, alkalies, organic surfactants, and polyelectrolytes. This paper discusses the use of dispersants in mineral processing, with an emphasis on control of slurry viscosity. The mechanism of dispersion and factors that affect the choice of dispersant will be discussed.

Jan 1, 1986

By C. J. Mwenifumbo

Preservation of groundwater quality is a major environmental concern. The disposal of hazardous material from urban waste dumps, milling wastes in tailings ponds, and industrial wastes in injection wells may contaminate potential sources of potable groundwater. The containment or migration of contaminants in the subsurface depends on bedrock characteristics and type of overlying sediments. Fractured bedrock and permeable sediments that may provide pathways for the transport of potentially harmful contaminants should be avoided when selecting a disposal site. The role of borehole geophysics in hazardous waste-site investigations is reviewed in three categories: (I) site selection; (2) determination of the extent of contamination at existing sites; and (3) long-term monitoring of migration of contaminants. In the first category, borehole geophysical techniques developed for lithology and fracture identification, and for porosity determination, provide some of the necessary information for understanding the subsurface hydrogeology. Lithological information can be obtained from gamma-ray, electrical resistivity, induction, magnetic susceptibility, and sometimes induced polarization logs; fracture detection and characterization can be accomplished with the use of caliper, density, resistivity, temperature, and acoustic televiewer logs. Estimates of porosity are derived primarily from neutron-neutron, resistivity, density, and soniclogs. Borehole geophysical techniques used in water quality determinations include self-potential, fluid resistivity, Eh (redox potentials) and pH measurements, and these can be used to map the extent of contamination at an existing waste site. Cross borehole and borehole-to-surface electrical methods can also be used in this application. Long-term monitoring of contaminant migration in boreholes can be accomplished with techniques that respond to changes in electrical conductivity, temperature and fluid chemistry caused by the presence of contaminants.

Jan 1, 1993