Search Documents

By N. E. Grosvenor

The study of rock mechanics is becoming more important each year and several groups are currently engaged in the study of rock mechanics instrumentation and techniques that can be used to determine rock properties in place. As it becomes necessary to mine lower grade ores, larger equipment and tonnages are required, which in turn call for larger openings underground. In addition, rock mechanics studies are necessary for designing large underground openings for defense and powerhouses, and highway and water tunnels. Meramec Mining Co. has a rock mechanics program in which they are trying to develop a means of detecting ground instability prior to failure. In one case advance warning resulted in valuable lead time for back filling stopes before pillar failure had progressed to a dangerous extent.1

Jan 2, 1968

By W. C. Phalen

"Tho the term “magnesite” is generally applied to the iron-bearing carbonate of magnesium, such as is found in Austria and Hungary, by some Austrian magnesite is referred to as bruennerite. The mineral bruennerite has become of commercial importance only in Austria. The important deposits are found in Styria, lower Austria and northern Hungary. It is of interest to know that the world's largest deposit of spathic iron ores or iron carbonate (FeCO3), occurs at Eisenerz, Styria, while the world's largest deposit of spathic bruennerite is found at Veitsch in the same province.The Styrian and lower Austrian deposits are located much nearer the Adriatic sea than are the deposits of northern Hungary; and it is from the former that most of the exported magnesite has come. They are located south-west of Vienna, and extend west from Semmering thru the Murz Valley to Tyrol. The chief deposits reckoning from east to west are those of Semmering, Veitsch, Breitenau, Trieben, Radenthein, and Dienten.The largest and most important deposit is that at Veitsch located near Mitterdorf, on the South Austrian railroad in the Murz Valley, Styria. Here the magnesite, which occurs in the form of a lens is quarried on the slope of a hill in a series of terraces about 50 feet apart. The entire work extends thru a vertical distance of 500 feet. The huge magnesite lens is nearly 4 of a mile long and over 1,000 feet in width, and probably extends to a considerable depth.The formation containing the magnesite extends eastward beyond Vienna into Northern Hungary where magnesite is quarried beyond Jolsva and Nyustya in the Gomor district. In spite of the remote location of these deposits as compared with those in Styria, magnesite was shipped from them before the war a distance of 360 miles to the port of Fiume for overseas shipments to other parts of Europe and to America.The average analysis showing the composition of the Austria-Hungary mineral is as follows:The magnesite occurs as lenticular masses in a belt of Carboniferous rocks consisting mainly of metamorphosed Shales, sandstones, conglomerates,,and limestone, It is grayish in color when fresh, and contains sufficient ferrous carbonate to blacken it when calcined. It turns brown owing to the oxide ion of the ferrous carbonate when exposed to the air. The quantity of carbonate of iron is ariable and different analyses show that it ranges up to 13 or 14%For the most part, only the sintered article has been imported into The United States. This material has achieved an enviable reputation for its uniformity both as to chemical and physical characteristics. The homogeneity of the sintered Austrian magnesite is doubtless due in part to the averaging effect of the different operations, such as crushing, dressing, sintering, And mixing, n effect which is not obtainable in mere hand samples.There is comparatively little variability in the sintered magnesite as marketed, and five analyses of this sintered magnesite as quoted by Cornu* are gas follows:"

Aug 1, 1919

By R. S. Moehlman

IN recent years, exploration and development by diamond drilling has become a popular attack on the problem of finding new ore shoots and developing extensions of known shoots. Diamond drilling has been used in recent years in extensive sampling of disseminated copper deposits, in preference to churn drilling. At the Harvard gold mine, near Jamestown, California, Philip R. Bradley, Jr., general superintendent, reports that: "The Harvard work was a singular example of the reliance that can be placed on diamond drilling in evaluating an ore body." Drilling at the Harvard mine will be discussed in a subsequent section of the paper. So popular has diamond drilling become, indeed, that many who have had slight experience with drilling are inclined to regard it as a cheap cure-all. This paper proposes to show some of the limitations on the application of drilling and some of the steps that should be followed in drilling programs to obtain reliable results. COST OF DRILLING Drilling has the advantage, over shaft sinking and drifting, of lower cost and greater speed. As compared with churn drilling, the advantage of bringing up a coherent sample instead of fine cuttings for a sample is obvious. Diamond drilling is generally more expensive, however, and more engineering effort is required in combining the average of core and sludge samples. Exploration of drift walls by hammer drills to a depth of less than 50 ft. is generally cheaper than diamond drilling, but beyond this depth the diamond drill is cheaper and more efficient. The principal factor in determining cost of drilling is the character of the ground drilled. Broken ground with many fissures is most expensive to drill. Hard ground is less of a problem with diamond drills than with ordinary machine drills. Hardness or softness affects only the speed of drilling. Caving, easily washed, sandy or clayey ground requires continual cementing and casing, which is the greatest cost problem. Thus, soft, incompetent ground is more costly to drill than hard, massive ground. Cost of drilling per foot in good to fair ground varies from less than $1 per foot, achieved in some districts in Ontario, the Mother Lode, and Missouri, to $5 per foot in many western states. In bad drilling ground, costs may range from $5 to $15 or more per foot, thus approaching the cost of drifting. Other factors that increase the cost per foot are: I. Short total length of hole drilled, so that the cost of moving in crews and equipment must be spread over a relatively few feet. 2. Cost of drilling per foot increases with depth beyond about 500 ft., as more time is consumed in pulling rods. 3. Cost of preparing drilling stations, getting air underground to stations, etc. 4. Inaccessibility and lack of water on the job make for higher costs.

Jan 1, 1946

By E. P. Klier, Taylor Lyman

THE structures formed when austenite is quenched to subcritical temperatures and allowed to transform isothermally have been the subject of intensive study since the work of Davenport and Bain.1 Isothermal transformation diagrams summarizing the results of many of these studies have become widely familiar to metallurgists. Of particular interest to metallographers are the dark-etching, acicular products of transformation formed by isothermal reaction below the temperature of maximum velocity of the austenite to pearlite reaction. These products, the bainite structures, can be formed in a wide variety of steels. However, the constitution of bainite is not well understood and divergent views have been expressed as to its mode of formation. In this investigation a combination of dilatometric, microscopic and X-ray methods has been brought to bear upon the problem in the hope of some elucidation of the bainite reaction as it occurs in hypoeutectoid steels. MECHANISM OF BAINITE FORMATION Davenport and Bain1 considered the mechanism of bainite formation to consist of two steps-an allotropic transformation followed by precipitation of carbide. The separation in time of the two processes was considered to be very slight in the upper temperature range and very marked at temperatures just above the martensite range. This concept has been restated by Vilella, Guellich and Bain2 in the form of a definition of the acicular mode of transformation as: The successive, abrupt formation of flat plates of supersaturated ferrite along certain crystallographic planes of the austenite grains; this supersaturated ferrite begins at once to reject carbide particles, (not lamellae), at a rate depending upon temperature. In effect, this is the acicular mode of transformation, even though the temperature be such as to limit the actual life of the quasi-martensite to millionths of a second. The investigation of isothermal decomposition of austenite in certain alloy steels (notably those containing chromium or molybdenum) has revealed that there may be a range of temperatures between the pearlite and bainite reactions in which the austenite decomposes at a relatively low rate.3-6 Further, it is characteristic that in the second region of fast reaction the decomposition of the austenite is incomplete by one reaction but goes to completion by a second reaction. These observations led Wever7 to a description of the bainite reaction as follows: I. The reaction takes place by initial precipitation of a martensitic intermediate structure. 2. In the upper temperature range this structure readily decomposes into ferrite and cementite. In the lower range carbon separates in an unknown form. 3. In the upper temperature range the precipitated carbide nucleates the precipitation

Jan 1, 1944

By A. S. Choudhary

India is endowed with a reasonably large reserve of chrome ore, amounting to about 100 million tons in different grades and is one of the leading producers of ore/concentrate along with South Africa, Kazakhstan and others. Chromite production in India has registered a 10 times increase during the last 30 years. Till late 1940s, the practice was to mine the high-grade ore for making ferrochrome and charge chrome and export the same leaving the low and medium grade ores stacked around the mine as waste material. This practice was continued for quite some time till the increase in world wide de-mand of chromite initiated an increase in production of chromite ore in India and the aspects of ?economy of operation? and ?conservation of mineral? dawned on the producers and associated authorities. Recovery of chrome values from low and medium grade ore was initiated to produce high-grade saleable concentrate. Suitable legislation was made by Government of India to induce and provide incentives to the operators to do so. First large scale chromite beneficiation plant in India was commissioned about three decades back at Byrapore in the Southern state of Karnataka. The ore, rather simple in nature and relatively free from clay, was obtained from underground. The processing consequently was simple washing and wet tabling. Further more, some test work, on the samples from eastern coast particularly from Orissa, was carried out at an internationally reputed laboratory by a large private operator and the plant was set up. This consisted of a combination of crushing-grinding-de-sliming-classification followed by concentration in multi stage spiral concentrators and shaking table. The plant was commissioned and operated successfully. Soon a state owned company followed suit on the basis of test work carried out in a well equipped Indian laboratory. The plant worked satisfactorily after some initial teething trouble and the company plans to double the existing plant capacity by installing balancing facilities. This development prompted a number of operators, including industry leaders to join the fray and the chrome ore processing industry flourished in India. More and more operators are now in the process of adding capacities to their existing plants. This paper attempts to chart the evolution of chrome ore beneficiation industry in India through a case study with reference to an existing plant. The process technology adopted and modified to suit the altered requirements as well as the future trends are outlined.

Jan 1, 2014

By P. V. Avotins, D. R. Nagaraj, S. S. Wang

Xanthates and dithiophosphates are the most commonly used collectors in the flotation of sulfide minerals. Other reagents such as thionocarbamates, mercaptobenzothiazoles (MBT), mercaptans and xanthogen formates occupy niche positions in industrial collector use. Over the last ten years there has been much activity by chemical companies to develop new collector compositions. The new collectors are aimed at meeting specific process needs such as recovering an increment of valuable metals, improved sulfide separations, increased flotation kinetics, and reducing reagents costs. A review of the patent literature shows that American Cyanamid (Cytec), Dow Chemical, Phillips Petroleum, Sentrachem Ltd., Henkel, Montan Chemicals and Elf Aquitaine, among others, have been active in sulfide collector research. Several companies have achieved considerable success in laboratory and plant tests of the new collectors; however, commercial acceptance for plant usage has been slow. Those most advanced have been plant tested extensively and some are in day-to-day use. The new collector types in this category are: Modified thionocarbamates, dithiophosphinates, organic sulfides, trithiocarbonates, monothiophosphates, and modified thioureas. Others such as substituted mercaptobenzothiazoles and monothiophosphinates have been tested in the laboratory. The chemistry of collectors developed in the last 10 years, their preparation, physical properties and their potential for commercial use are reviewed in this paper.

Jan 1, 1994

By C. M. Marquardt

The minerals industry in general should bow in homage to the uranium milling industry. Those in the uranium milling industry have "spark- plugged" more progress in the application of instrumentation and control in the last 5 years than has been made in 50 years by the industry in general. Part of this real progress in the application of instrumentation and control has been born of necessity because milling processes are more complex. A lot of the impetus for instrumentation and control has come from the fact that the industry is new, the processes are new, and there are no hide-bound conventions to overcome. Part of it comes from the fact that much of processing is more chemical than metallurgical and the thinking of the process chemist has carried over into the plants. One need not elaborate on what instrumentation has done for the process chemical industries. Each new mill that is constructed, if of appreciable size, seems to employ more instrumentation than the previously completed plant. Plant A makes a break-through in the application of instrumentation to a particular part of the process and Plant B accepts this and goes one step farther, while Plant C, anticipating Plant B, makes two or three more steps before Plant B is entirely leveled out.

Jan 9, 1958

By M. Helinski

In the authors? experience inappropriate water management in hydraulic fill masses has been the root cause of most barricade failures. Inappropriate water management can lead to high water pressures, reduced effective stresses and increased barricade stresses (Kuganathan 2002). In addition the high hydraulic conductivity and non-plastic nature of most hydraulic fills makes susceptibility to piping failure (Cowling et al. 1987) a high possibility in many hydraulic backfills where a static water head is available. In order to avert both of these failure mechanisms it is essential to control the elevation of the phreatic surface within the fill mass. This is usually achieved through campaigned filling and resting periods. The duration of filling and resting periods are often estimated using some form of stope drainage simulator. Due to the random nature of many characteristics that influence the fill mass hydraulic conductivity, simulation of hydraulic fill drainage can be difficult. The high consequences of inaccurate phreatic surface estimates combined with the high variability in drainage properties often results in operators taking a conservative approach to this modelling. This conservative approach can lead to significant delays in the filling cycle which can have a major impact on the productivity of many hydraulic fill operations and can often results in an unnecessary movement towards capital intensive paste fill systems. This paper presents a water management technique which combines a simplified drainage model with in-situ monitoring to provide a rational approach to water management. With an accurate drainage model filling operations can be carried out at optimum efficiency without compromising safety. The implementation of this strategy has lead to a significant increase in filling rates at a number of Australian filling operations. A brief case study from one of these sites has been presented.

May 1, 2007

By H. H. Alexander

IN the early part of the last century textile fabric was used for the filtration of products of combustion and lampblack was obtained by passing smoke through a series of canvas bags. Natural draft was, used to draw and force the smoke through the bags. About 1850 bag filtration was used for collecting zinc oxide. Around 1876 it was introduced for collecting the fume from lead-ore hearth smelting in. Missouri. Shortly afterward it was used, first at Portland, Me., and later at Canon City, Colo., for the collection and production of zinc-lead pigment in treating mixed zinc-lead sulphides. In 1890 the Globe Smelting & Refining Co., at Denver, Colo., installed a bag house containing 1,458 bags for the recovery of fume from silver-lead blast furnaces. This installation was too small to handle all of the gases and was increased to approximately 2,300 bags. . In 1900 the number of bags was again increased, making a total of approximately 2,800: The usual difficulties incident to new installations were encountered, but they were gradually overcome and the bag house became accepted as standard practice for this class of smelting. As all of the bag houses built since have followed the general lines of the Globe installation, a short description may be of interest. The general construction of the Globe bag house is shown in Figs. 1, 2, and 3. The building is 149 ft. 8 in. long by 67 ft. 4 in. wide and 40 ft. 2 in. high from the basement floor to the eaves of the roof, having brick walls 26 in. thick from the foundation up to the thimble floor, from there an 18-in. wall for 16 ft. and a 13-in. wall from this point to the top, a distance of 14 ft. 2 in. Additional stiffening is given to the walls above the basement by pilasters located every 16 ft. The end-wall construction is similar to that of the side walls with the exception of the spacing of the pilasters, which is somewhat greater. The roof is made of corrugated iron laid on 1-in. boards and supported by a timber frame work spaced 16 ft. apart resting on the basement partition walls. On top is a louver running the

Jan 8, 1914

By E. G. Gaylord

A BRIEF review of the oil conditions in California for a few years prior to 1923 is desirable for a clear comprehension of the development during that year and the results of the development. California's oil production during the five years preceding 1922 had been running from 100,000,000 to 115,000,000 bbl. annually. Crude oil stocks in storage had been declining steadily from 1915 to 1919, when there was a slight increase. They continued to decline through practically all of 1920, when they were drawn on to the extent of 11,350,000 bbl., leaving 20,930,000 bbl. on hand. In 1921, with production approximately 10,000,000 bbl. greater than the previous year, crude-oil stocks increased until, at the end of the year, there were 33,289,000 bbl. on hand. It would seem, therefore, that at the end of 1921 the so-called Pacific Coast province could absorb between 100,000,000 and 105,000,000 bbl. of oil per year, any in excess of this amount going into storage, not being, able to compete in other markets with oil outside the state. During 1922, daily production increased from 316,000 bbl. at the beginning of the year, to 500,000, at the end. This increase was the result entirely of production from the new fields, in the Los Angeles basin. In fact, considerable oil from the older fields of the state was shut-in beginning with March, 1922. As of 1922, the past development of the oil industry of California had been, in a general way, quite regular. As the need grew for more oil, pioneer drilling was increased, resulting in the discovery of new fields here and there. The good prices for crude oil that prevailed during the later part of the War and into 1921 had stimulated an extensive wildcatting campaign by California's larger oil corporations, as well as by smaller independent oil companies and by individuals. Many wildcat wells in California have required, two or three years for their completion, consequently the intensive wildcatting, which might be said to have started in California in 1917 and continued into 1922, found its greatest results with, the discovery of three very productive fields which, for all practical purposes, might as well have come in simultaneously.

Jan 3, 1924

By Edwards A. B

Occasional, sporadic and small occurrences of lollingite in the Broken Hill lode have been described,(l) mostly in the garnet sandstone in the foot-wall and under-wall of the Broken Hill lode. The lollingite contains appreciable percentages of cobalt and nickel and is regarded as an early mineral in the development of the lode; and, with the incoming of the sulphides, it has suffered considerable replacement by arsenopyrite. During the conversion of iron arsenide into the iron sulpho-arsenide, ilie nickel and most of the cobalt are removed in solution and are inferred to reappear in niccolite and other minerals that have been recorded among the later minerals of the Broken Hill lode. As a result of observations of the officers of ilie Broken Hill South Ltd., an occurrence of cobaltite can now be recorded which has developed by an analogous type of replacement.Cobaltite has previously been recorded from the Australian Broken Hill Consols lode in the vicinity of the rich deposits of silver, though not in contact with them. Cobaltite has been found in the northern extremity of the No. 2 lens of the Broken Hill lode at the 1,480 feet level of the Broken Hill South...

Jan 1, 1944

By Brook W. H

The history of the reduction of iron from its ores is lost in antiquity. Archreologists state that man has practised it for over four thousand years. Until comparatively recent times charcoal was the principal reducing agent for making metallic iron from its various oxidised ores. Coke was first used by iron founders in England in 1619, and its use spread gradually throughout the civilised world from then onwards. Indeed, the destruction of forests to obtain the requisite charcoal made the iron founders, both in England and America, extremely unpopular, and this hampered the iron industry to a considerable extent, until coal provided the metallurgist with a new and better fuel--coke which is used by most pyro-metallurgists today. The transition from wood to coal products for iron smelting had a profound effect on the location of iron works. Particularly was this the case in America where, in the infancy of the industry, practically each of the early States had its own iron producers, but as coal and coke replaced charcoal, there came about a concentration of the iron and steel industry around the coking coal deposits, and so today there are huge steel plants clustered around the soft coal basins in Pennsylvania and Illinois.The development of the iron and steel industry in Australia, which is comparatively recent by world standards, has been cradled in the coal basins of New South Wales. The first steel works of any consequence in this country were built near Lithgow, close by the mines which produced the coal for coking.Incidentally, these works were rather unique in that the three essential materials for iron and steel manufacture-ore, coal, and limestone-were found virtually at the works' back door.When, in 1912, the location of the proposed steel works for The Broken Hill Pty. Co. Ltd. for smelting ore from Iron Knob in South Australia was considered, the site ultimately chosen was at Newcastle, almost on top of seams of satisfactory coking coal. One of the major factors which had determined the site of the steel works was the fact that, about 1912, three tons of coal were required to produce one ton of finished steel product, and the relative economics of ore and coal haulage were much in favour of bringing ore to the coal.

Jan 1, 1947

By H. J. Struth

The benefits of proration of oil production were perhaps more concretely realized in 1932 than at any time since the oil industry adopted nation-wide production control. Reduced output of crude petroleum, which brought the daily average of the United States down to approximately 2,000,000 bbl. from a peak in 1931 of more than 2,600,000, had a telling effect on the trend of oil prices. Mid-Continent crude was advanced in price from 776, for 36-gravity oil, to $1.04 a barrel. California crude, of 26-gravity at Signal Hill, moved forward from 736 to 976 a barrel. Pennsylvania crude, the only exception to the upward trend, rose in price from $1.82 per barrel to $2.02, only to react to $1.72. This was due to local conditions which necessitated an adjustment to overcome competition from other areas of the United States. East Texas continued to exert a far-reaching influence on the crude and gasoline market during 1932. Despite the fact that oil prices were advanced in most fields, large quantities of oil were produced in East Texas in violation of state proration orders, and sold in the market at prices considerably below official postings. This created competitive conditions in the gasoline market that were felt by all refining centers of the United States. The quantity of gasoline produced from cheap East Texas crude was not large, but the volume was sufficient to influence prices in practically all sections of the country. Thus, while the industry's' economic situation showed visible improvement statistically, the unreported and unseen statistics originating in East Texas proved to be an insurmountable obstacle to the economic betterment that was otherwise apparently justified. Somewhat surprising to many was the fact that gasoline consumption was maintained within 10 per cent of the preceding year. Domestic consumption showed only a net decline under 1931 of about 8.5 per cent; exports dropped in volume to the extent of about 23 per cent. As a matter of fact, domestic gasoline consumption was only about 1.4 per cent less than it was in the predepression year of 1929. Exports, however,

Jan 1, 1933

Dynamic shocks, which occur in mine hoisting systems have been measured by various investigators over the past 30 years. In 1966 the most intensive analytical investigations were being planned in Bochum, Germany, where equipment then was being constructed to measure the power generated in any particular dynamic shock. Between 1953 and 1956, in Broken Hill, N.S.W., accelerations of the shaft conveyances were measured and analysed. The "effective mass" of the conveyances at the time of the shock was then and still is considered as indeterminate and not easily measured. It is believed that probable peak forces can be determined by the product of the static mass and the accelerations. The subsequent problem of the elimination of the dynamic shocks becomes one of possibly increasing the frequency and thus reducing the amplitude, after identifying and evaluating the shock generators. In addition, judicious use of the clearance between the shaft conveyance and the guide, as a zone in which to absorb vibrations, is a factor which has been overlooked in earlier investigations on This topic.

Jan 1, 1971

By M. S. King

A series of cross-hole acoustic measurements have been performed in a columnar-jointed basaltic rock mass around an underground opening mined by the drill-and-blast method. The purposes of the test program were: to evaluate the rock mass characteristics around the opening; to determine the zone of blast damage; and to evaluate seismic methods for anomaly detection ahead of mining in this type of rock. The cross-hole measurements were made between four 76-mm diameter horizon- tal boreholes diamond-drilled 12 m into a wall of the underground opening. Repetitive pulses of compressional (P) and shear (S) waves of frequencies in the range 3 kHz-100 kHz were propagated from a transmitter sonde through the rock mass to a receiver sonde, both of which were clamped hydraulically to the borehole wall. After amplification the received P- and S-wave signals were digitized at the surface by a digital oscilloscope and stored on floppy discs. The results indicate considerable reductions in P- and S-wave velocities at distances less than 2 m from the face. Clearly these low values are associated with blast damage. Beyond 2 m, the velocities in a vertical direction indicate almost constant values. The velocities in the horizontal direction beyond 2 m appeared erratic, but showed a general tendency to increase as a function of distance from the face. Their maximum values remained, however, still lower in value than the corresponding velocities in the vertical direction. Near the face, the differences in velocities were considerably greater: with horizontal velocities considerably lower in value than those vertical. Results of the spectral analyses of the received signals indicated that Q-values were strongly influenced by the vertically- oriented sets of joints. Only for waves travelling in the vertical direction was the effect observed of the blast-damaged zone immediately around the opening. The acoustic data obtained are clearly indicative of an anisotropic jointed rock mass, with a greater intensity of jointing for travel paths in the horizontal than the vertical direction. The vertical, columnar joints are probably less tightly closed than those oriented in the horizontal plane.

Jan 1, 1984

By Norman Weiss

The purpose of this paper is to relate progress in the engineering field called Minerals Beneficiation to undergraduate and graduate education in our colleges and universities. So mach has been written recently about the education of scientists and engineers that I've had to struggle against the temptation to repeat what has been often said before, particularly because man like Robert Mehl of Carnegie Tech, Antoine Gaudin of MIT, H. M. Davis of Penn State, and John Vanderwilt of Colorado School of Mines have recently written many quotable paragraphs on the subject. In the matter of progress, the rapidity of proliferation in the area of physical and chemical beneficiation is convincing proof that this is indeed a lively art, and having been a millman for 35 uninterrupted years I prefer to lean on personal observations to some extent, rather than on statistics and charts v culled from the journals. I propose in this paper to talk first about the progress we've made in our branch of the mining industry in the last 3 decades--particularly in the last few years--and try to show that future progress will depend upon the quality of education and capacity for research possessed by our colleges. The second part will deal with some of the problems the colleges encounter in trying to fulfill these responsibilities.

Jan 1, 1959

By David Newman

Multiple seam underground coal mining is ubiquitous in Appalachia. Many coal properties have from two to ten or more economically mineable coal seams. Because of the ability to penetrate 600-feet to 1,000-feet or deeper into the mountainside leaving panels of web pillars separated by barrier pillars, highwall mining is a hybrid between surface and underground mining. As a result, many of the ground control problems commonly associated with multiple seam underground mining exist with multiple seam highwall mining. These include: i) multiple seam interaction between web and barrier pillars in superjacent mines, ii) subsidence and caving propagating to overlying seams and mines, iii) pooled water and the potential for inundation resulting from a breakthrough between an active highwall mine and abandoned underground mines in the same or superjacent seams, iv) the presence of overlying or underlying mine workings where pillar columnization in the active mine is not possible, and v) the question of whether to mine ?top-down? or ?bottom-up.? Case histories are presented from southeast Ohio where the Middle Kittanning No. 6 and Lower Kittanning No. 5 seams are successfully highwall mined with 20-feet to 40-feet of largely shale interburden. A highwall miner was caught in a highwall collapse in the Middle Kittanning No. 6 seam when it was overmining auger workings in the Lower Kittanning No. 5 seam. Multiple seam interaction caused by the overmining transferred overburden stress onto the Lower Kittanning No. 5 seam. The overburden concentrated through web pillars initiated auger web pillar failure, resulting in roof collapse and subsidence in the Lower Kittanning No. 5 seam that propagated up to the Middle Kittanning No. 6 seam. A second case history involves multiple seam highwall mining in southeast Kentucky. The A3 Rider, A3, B2, and C1 seams are being highwall mined around abandoned underground mines in the A3 and B2 seams and augering in the A3 Rider. Because of spoil storage constraints for the surface contour mines, the highwall miner follows the active pits in each seam so a standard sequence of ?top-down? or ?bottom-up mining does not exist.

Jan 1, 2009

By Sidney A. Swensrud

This paper reviews the subject of gasoline margins, discusses some of the more current marketing problems, and gives some consideration to the main urges to marketing expansion, or overexpansion, in the oil industry. Margins In an earlier paper1, some comparisons were shown for the years 1929, 1930 and 1931, of the margin between the refinery cost of gasoline in Oklahoma, the market price in Oklahoma, and the average retail price in 50 representative cities of the United States. These figures indicated a small margin for the refiner in 1929 between his gasoline cost and the wholesale price, which, however, had turned into a loss by 1931. The margin between either refinery costs or wholesale prices and the retail price in the 50 cities showed a continuous decline during the three years. We have now worked out these figures on a similar basis for a longer period—from 1928 through 1936. The figures for refinery gasoline cost are slightly different from those in the earlier study, owing to the use of

Jan 1, 1937

By L. A. Walker

DURING the past twelve years the underground shaft of the United States mine at Bingham has been sunk an additional 2000 ft. with stations and pockets cut every 200 ft. without interrupting the mining of 600 tons of ore per day and the advancing of 1500 ft. of development per month. Following is a brief description of the way the joint work is conducted. The vertical underground shaft is a three-compartment shaft with outside dimensions of 6 ft. 4 in. by 15 ft. 6 in., and inside dimensions for each compartment of 4 ft. 2 in. by 4 ft. 8 in. The manway compartment of the main shaft is used as the hoisting compartment in sinking operations; it is partially lined with 2 by 12-in, lagging and a bucket is used without guides or crosshead. Preparatory work includes the placing of a bulkhead in the manway compartment, 60 ft. above the lowest station or level, the installation of a hoist, a head sheave, a fleet sheave, a-signal system, air and water lines, and a trap door for handling waste.

Jan 1, 1937

By R. A. Kinzie

In a conventional cement plant, the drying and heating of the raw material takes place in the upper section of a cylindrical kiln where the heat exchange is poor. In a Lepol kiln this part of the process is carried out on a traveling grate where the heat exchange is efficient. The increase in fuel economy justifies the greater complexity of the installation.

Jan 1, 1950