Search Documents

By J Rubio

This work presents design features of an innovative in-line mixing helical (coiled) reactor for flocculation and flotation as a solid-liquid separation process for suspended particles (including liquid droplets). The device has been named flocs generator reactor (FGR), a compact system whereby the flocculation of particles is assisted by the kinetic energy transfer from the hydraulic flow through the reactor and/or by the injection of microbubbles (30 - 70 ¦m). The flow mixing presented a plug flow regime with a low dispersion degree, promoting the required hydrodynamic conditions to disperse the polymer flocculant (cationic polyacrylamide) and to generate æstrongÆ flocs of Fe(OH)3 or clays (as colloidal model systems) with aggregation using an anionic polymer, Al2(SO4)3 and poly aluminium chloride (PAC), and oil emulsions destabilisation with a high molecular weight cationic polymer. The solid-liquid separation of the flocs was then achieved either by settling or by flotation with microbubbles. This paper discusses advances in this new in-line flocculation-rapid flotation device to remove æaerated aggregatesÆ, aggregates with entrained and entrapped bubbles. Studies were carried out with different models of FGRs (varying the length:volume ratio) and process efficiency (mainly kinetics) evaluated as a function of polymer concentration and some operating parameters, namely, feed flow-rate, air:solids ratio and residence time. Results showed that the aerated flocs are readily floated with rising rates in the order of 120 mh-1, values higher than those obtained for the settling of the non-aerated flocs (18 - 24 mh-1). The FGR requires short residence times and generates dense, well structured flocs (with a mass fractal dimension, dF of about three) which withstand high shear forces. Mechanisms involved appear to include small bubble formation and their rapid occlusion (entrapment) within flocs, nucleation of bubbles at floc/water interfaces, polymer coiling as a result of æsalting outÆ effects at the aqueous/air interface and plug flow type of mixing (flocculation). Successful examples of emulsified oil and solids removal from water are shown and because in all cases high efficiencies were obtained (>90 per cent removal). Due to the high process efficiency and high loading capacity shown, the FGR appears to have good potential as an in-line flotation-separator device in applications requiring high rate solid-liquid or liquid-liquid separations.

Jan 1, 2005

By S. L. Gula

"Effective and timely communication during routine operations, and especially during emergency situations, is no easy task in any underground mine. At Cominco Fertilizers, Potash Operations, where 150people are employed underground to produce 3.1 million tonnes of potash per annum at a depth of 1100 m (3600ft), this is no exception. The over-all mine workings underlie an area of approximately 20 km 2 with average travel time to the active mining areas being approximately 30 to 40 minutes by light vehicle, and significantly longer than this for heavy equipment.In a mine of this size, the deployment and management of personnel and materials on a day-to-day basis, and during mine emergencies, is an important exercise. The Personal Emergency Device (PED) system has provided the Potash Division a means to achieve improvements in this area and reduce the communications bottleneck.The MineAt Cominco Fertilizers Potash Operations, approximately 30 km southwest of Saskatoon, the orebody is the same horizon being mined by other potash producers in the Saskatoon area and extends over 300 km in an east-west direction, and approximately 150 km in a north-south direction. Mining operations are carried out with approximately 150 employees operating on a continuous-shift basis, seven days a week.Mining is presently being done from Block 6 which takes the mine to its northernmost boundary and contains reserves of approximately 50 million tonnes. Production is from one level by five twin rotor continuous mining machines, each capable of cutting a face up to 5.5 m wide and 3.3 m high . All ore is transported to the shaft via approximately 20 km of conveyor where it is removed to surface by two 24 tonne skips.After the ore is conveyed to the mill for processing, the finished product is shipped by rail car or trucks to other parts of Canada, the United States or through Vancouver to other parts of the world."

Jan 1, 1993

By Robert M. Owen

Recent advances in coring technology and in the development of shipboard and/or in situ geochemical geochemical analysis systems have greatly improved our ability to collect and analyze exploration samples, particularly for marine placer exploration programs. The potential benefit of these improvements cannot be fully realized, however, until we also develop more efficient methods of data reduction and interpretation. Specifically, there is a need to provide prospectors with rapid and useful interpretations of the raw geochemical data so that they can exploit promising results and otherwise optimize the exploration program while the exploration vessel is still at sea. The goal of this project has been to identify and/or develop computer software which is capable of making the necessary data reduction calculations and which can be run on conventional desk-top computers. All work on this project has been supported through a research grant from MMTC-CSD to The University of Michigan. The first stage of this effort involved an evaluation of commercially available (i.e., "off the shelf") software to determine its suitability for use in marine placer exploration applications. Various commercial software packages, each purportedly capable of making different types of statistical and/or mathematical calculations, were tested by evaluating their performance in handling geochemical data sets representative of actual marine placer locations. These data sets include the positions and results of chemical analyses of suites of sediment samples collected from areas of known or suspected marine placers along the Bering Sea coast of Alaska. The evaluation of each commercial program involved a comparison between the results obtained from using the test program

Jan 1, 1991

By Sigmund J. Sulinski

All Sanitary District contract documents for new tunnel construction permit the Contractor a choice of four (4) separate alternate tunnel sections. This is the result of a continuing District policy to encourage at all times the use of the most suitable construction techniques and to attract to District construction the broadest spectrum of proven capabilities. Figure 1 indicates the alternate tunnel sections allowed on District contracts as follows: 1. A horse shoe section, ribbed and lagged, and a poured reinforced concrete tunnel liner; 2. Circular section, ribbed and lagged, and a poured in place reinforced concrete tunnel liner; 3. Circular section, ribbed and lagged, and a precast reinforced concrete pipe liner grouted in place; and 4. Circular section, no temporary lining, and a precast reinforced concrete pipe liner to be jacked in place. The Sanitary District now has in operation 10,500' of 5'6" I.D. and 6,500' of 5'0" I.D. jacked tunnel. An additional 5,600' of 7'6" I.D. jacked tunnel is currently under construction.

Jan 1, 1997

By Freeman Bishop

Copper production has been under Government scrutiny for many years because it's known as a concentrated industry which in turn creates what many economists label administrative prices. Neither of these conditions is illegitimate, per se, the Federal Trade Commission and the Justice Department have said time and again. But Justice spoke up once more. This time over a Puerto Rican copper development planned by American Metal Climax, Inc., and the Kennecott Copper Corp. Bureaucratic Dichotomy Creates Confusion and Conflict In the Copper Industry Ian MacGregor, chairman and chief executive officer of Amax, said Justice in a recent communique questioned the propriety of the proposal of a joint copper venture in Puerto Rico. At the same approximate time, Dr. Hendrik S. Houthakker, chairman of the President's Commission on Copper, was urging copper producers to expand production to help hold down prices by making more copper available to all consumers. This, Mr. MacGregor said, is creating confusion and conflict, since the Administration from one source is chastising the industry for doing what another branch requests.

Jan 1, 1970

Pulverised coal firing was pioneered in the cement industry prior to the turn of the century. Ash from the coal is absorbed into the mix in the kiln and replaces secondary materials. With high purity limestone coal with high ash content can be used. Fuel cost is a major part of the total manufacturing cost. Cement plants are thus quick to respond to fuel price changes and will use low grade fuels if there is a price advantage. Combustion conditions in a cement kiln differ markedly from a boiler. Flame length is determined by air/fuel mixing but because of fixed secondary air conditions this depends on primary air momentum. Volatile content has some effect on flame length but this can be offset by coal fineness. Much of the heat for cement production is for limestone calcination which is a low grade energy requirement. By allowing long residence time in separate direct fired vessels which then feed the high temperature kiln the energy of materials such as oil shale, tyres and lump lignite can be utilised.

Jan 1, 1987

By T. L. Baum

External oxidation during in-line heat treatment of TRIP steels can cause problems for the subsequent coating process. This research aims to elucidate the kinetic rates of internal oxidation, external oxidation and decarburization and their interdependence under different gas atmospheres and temperatures. A rolled steel sample chemistry of 0.14 wt.% C, 1.8 wt% Mn, 0.6 wt.% Si and 1 wt.% Al is used as a case study. Thermogravimetric techniques are used to examine the net mass change in a sample during heat treatment and the results show an initial mass decrease and later an increase for particular partial pressures of H2O. SEM-EDS, optical microscopy and glancing-angle x-ray are used to quantify the microstructure. The cross-section of the samples have 4 distinct zones: (i) an external scale, rich in fayalite, (ii) an internally oxidized region with Al, Si and Mn oxides in an Fe matrix, (iii) a decarburized steel region, characterized by large ferrite grains and low carbon content, and (iv) a relatively unaffected steel core with a structure similar to the starting material.

Jan 1, 2006

By W. S. Weldon

The use of spiral separators for the beneficiation of fine coal typically in the size range -2+0.1mm is now well established process technology. Developments during the mid 1980's resulted in the production of cost effective, efficient large diameter coal spiral separators. Recent developments and research have been geared to optimize metallurgical performance, materials handling and equipment geometry of large diameter coal spiral separators.

Jan 1, 1997

By J. D. Lowell

The gold content of prophyry copper deposits ranges from less than .05 gmt (ppm) to more than 1.0 got, and most deposits contain on the order of 0.05 gmt Au. Perhaps the highest grade mineralization which has been found in close proximity to a porphyry copper is the Ok Tedi Gold Cap orebody whose grade falls in the 2-3 gmt Au range.

Jan 1, 1988

By Henry G. Granger

DURING upwards of three thonsand miles of canoc-travel in South America, including several mishaps, the writer has unfortunately lost his book of notes taken during the year 1894 in Dutch Guyana, or Surinam. But a year spent in a foreign country, visiting its principal mining properties, is necessarily productive of indelible memories and impressions, and some of these may be of interest to the Institute. The Guyanas include British, or Demerara, Dutch, or Surinam, French, or Cayenne, and the Disputed Territory, or that portion of Brazil on the northeast coast of South America. After passing the picturesque mountainous coasts of Colombia and Venezuela, one reaches a low, flat mud-bank which extends far out into the sea, so that from the steamer, over a couple of leagues of turbid, shallow water, one call just see the dismal outline of the pestilential "bush" that fronts the Caribbean sea, clear around to the mouth of the Amazon. Here, iii the order mentioned above, are the Guyanas. So much has been said about this out-of-the-way section during the late excitement over the Venezuela boundary question, that the historical part of the subject may be advantageously condensed. Gold-mining in the Guyanas is altogether placer-mining, and is of the same general nature throughout; hence by describing the methods in use in Surinam and the results there achieved, ail idea will be given of the work throughout the field. The product of this section is about three to four millions of dollars annually, mostly from Demerara, not because of superior richness of its placers, but as a result of its very much larger population, which exceeds twice the aggregate census returns of both Surinam and Cayenne. Mining ill all this section is of comparatively recent date, and is indirectly due to the decline of the sugar-industry. After the introduction of beet-sugar scores

Jan 1, 1897

By C. R. Machado

Sossego Mine was the first Vale SAG mill operation to process copper-gold ore. It is located in the state of Para, in the south-eastern Amazon region of Brazil. In the first six years of continuous operation, Vale investigated different alternatives for improving circuit performance by investigating operating conditions, mainly focusing on the SAG mill. Today, after a steady increase over five years the annual production rate seems to have stabilized. It is hoped this work will show how the SAG operating practice have been perfected with time and as new data are collected. Historical data of mill grind-outs and crash stops helped create operation curves depending on the ball charge volume and total charge volume. Also noted were impacts on throughput due to the effect of reducing liner weight and the ore type characteristics.

Jan 1, 2012

By Yoshihiro Kawarabata

INTRODUCTION With only about 30% of Japan's entire population served by sewer systems at the end of 1980, extensive sewerage construction programs have been implemented. As major sewer networks in large cities are near completion, construction of smaller sewer networks in less populated areas and branch sewers in urban areas is on the rise, where a demand for sewer tunnels of 600mm to 1500mm diameter is very heavy. The pipe jacking technique, usually employed to excavate such small diameter tunnels, therefore has become the subject of further technological development and sophistication to cope with the increasing volume of construction. At the 1979 RETC, the state of the art on the slurry shield tunneling method at that time was reported. This paper is a follow up to the last paper and discusses a newly developed boulder crushing equipment and automatic pipe jacking system for the slurry shield method and their application. Such technological advancement as high-degree mechanization and automation will significantly improve tunneling operations in response to the aging society to come. Through application of the technique on so called factory automation, this is a step towards field automation for the construction industry.

Jan 1, 1983

By Jan J. Cilliers, Nicolas Barbian, Esther Ventura-Medina

"Mineral froth flotation is one of the most widely used processes to separate particles of valuable mineral from its associated gangue. It involves the selective separation of the hydrophobic particles from the slurry into the froth. The hydrophobic particles attach to the air bubbles and rise up to the froth phase on top of the slurry. The valuable mineral is collected when the froth overflows the cell wall. The separation performance of the process can be linked to the amount of solids and valuable material loaded on the bubble shells. In addition, it is well known that in most mineral systems, the presence of solids can enhance the stability of the froths. How the solids get to be distributed and what proportion is actually attached and stabilising the bubbles is not well known.This study aims to establish the relationship between operational variables, solids loading on bubbles and flotation performance. For this purpose, a series of industrial experiments to sample the solids in the bubble films under different operational conditions were carried out in two copper concentrators under steady state conditions. Samples of the lamellae were taken by touching the top surface of the bubbles with a glass slide. The amount of solids and liquid per unit area in the bubble lamellae can subsequently be estimated gravimetrically and by image analysis. The grade of the attached particles was also measured by adequate sampling. This gives an indication of the maximum grade that could be achieved from the process under the operating conditions."

Jan 1, 2003

The Western Cape Branch of the SAIMM recently held a one-day colloquium on the use of artificial intelligence (AI) in process engineering in the I.S. Gericke conference room at the University of Stellenbosch

Jan 1, 1992

By William Allen

For the past six years gravity surveys have been used for underground prospecting in the copper mines at Bisbee, Ariz. The primary purpose of the surveys has been to reduce the diamond drilling and crosscutting necessary for exploration. Since many of the orebodies are small, and geologic control is not always apparent, any information that will direct the drilling and crosscutting is highly desirable. Because of extensive development and exploration work in the copper mines at Bisbee, it has been possible to cover more than 630,000 ft of crosscuts on 30 levels with the gravity surveys. In the process the gravity procedures have been refined to a high degree.

Mar 1, 1956

By T. Malterer, R. Adams

Peat has unique physical, chemical and biological properties. These include high porosity and water retention, high absorption and adsorption properties, and high buffering capacity. In addition, peat is a rich medium for microorganism activity. Peat has traditionally been used for horticultural purposes. However, in recent years, peat is increasingly being used for waste- treatment purposes. This paper reviews North American literature on the use of peat for waste-treatment applications. The literature indicated that peat has potential for use in the treatment of municipal and on-site effluents, for the removal of low concentrations of heavy metals and for the adsorption of liquid and gaseous hydrocarbon pollutants.

Jan 1, 1997

By Edwin B. Johnson

The success of self-fluxed sinter in enhancing the operation of the blast furnace during the past few years has reasonably led to the assumption that the use of self-fluxed pellets might result in even greater furnace efficiencies. A great share of development work in agglomeration has been directed towards techniques related to the production of self-fluxed pellets, but no appreciable tonnage of self-fluxed pellets had been produced on a commercial scale until this past year when The Cleveland-Cliffs Iron Co. produced 35,000 tons of such pellets by the grate kiln system at the Republic mine during the period May 21-June 5, 1962.

Jan 3, 1963

Cominco Ltd's Polaris Mine in Canada's High Arctic has been successfully mining zinc ore in permafrost since 1981. Mining methods using frozen backfill have been the key to success. The mine is now producing about 60 per cent of the ore from pillars while maintaining high productivities. Annual ore production is just over one million tonnes providing more than 200 000 tonnes of zinc concentrate each year. Cominco Ltd has adapted management and operating practices to suit the harsh environment and the isolated site, and has shown that a profitable development can be carried out in the tough Arctic conditions, with minimum impact on the environment.

Jan 1, 1993

By T. B. Armstrong

"The developing world energy crisis and spiraling fuel costs have created a new public awareness and general acceptance of the need for energy conservation.Plants will have different objectives for an energy conservation program but there appears to be a common approach on how to save electrical energy.Data for a 180tph Rod Mill powered by a 750 hp motor will be used to demonstrate the relationship of energy input and production levels and to seek an optimum operating condition.Energy Conservation:Plants that have examined ways of dealing with the energy situations have concluded that energy conservation has important benefits for industry, including reduced costs, fewer production slowdowns inthe event of fuel shortages and a continued competitive position.There have been some ""startling"" conservation achievements attained through such simple plant maintenance and operating practices as reducing unnecessary lighting in buildings and yards, turning off' equipment not needed at night or over week-ends, through planning maintenance and production schedules to minimize energy use and through improving quality control to eliminate waste.Significant reducti.ons in energy use have been achieved by some rather simple but vigorous maintenance and plant engineering efforts directed at finding and fixing energy ""leaks"" rather than technological advances or major rework or redesign of facilities and equipment.An Energy Conservation Program often must overcome such obstacles as historic operating practices and emp1-oyee indifference, i.e. the ris.ing costs of fuel should result in re-examination of so1ne basic attitudes to energy conservation. Some measures, rejected in the past largely on the grounds of capj.tal. expenditure, now make economic sense in the light of future escalating energy costs."

Jan 1, 1978

By Michael L. Sorokin

The various methods of converter slag cleaning operation are analysed from the thermodynamk point of view: cleaning using coal, cleaning using combustion products of natural gas and cleaning in presence of matte. All calculations were done, applying the developing computer procedure based on the free energy minimisation algorithm. Three-suffix Margules equations were used to calculate thermodynamic properties of melts; The calculations resulted in recommendations for the practical appliance.

Jan 1, 1995