Search Documents

By Horace Knerr

IT has been shown1 that the resistance to corrosion of duralumin sheet is greatly influenced by the quenching medium used in heat treatment, or, more specifically, by the rate of cooling during quenching. The severity of corrosive attack after exposure to salt-water spray increases in the following order: DEGREE OF CORROSION, BY INSPECTION, QUENCHING MEDIUM AFTER 30 DAYS OF SALT-WATER SPRAY TEST; Water, cold (60° F.) Very slight. Water boiling Slight, but more than with cold water. Oil (70° F.) Slight, but more than with cold water. Air, fan blast, 65° F Severe, scaled. Air, still, 65° F Deeply scaled. The tensile strength, yield point and elongation are only slightly affected by the quenching medium, as shown in Table 1.

Jan 1, 1930

By Edward Sampson

Despite the many industrial uses, the world market for silver as a commodity is far from free, being dominated by the U.S. Government both through acts of Congress and by policy of the Treasury Department. This discussion will consider aspects of supply, demand, and price with a view to the future. Changes in Sources of Supply: The world's peak production of silver, 278 million oz, was in 1937. In the 1850's world production was about 30 million oz, having risen from a yearly average of 11 million oz for the first half of the century. From 1860 to 1940 there was a steady rise, broken only by World War I and the depression of the early 1930's.

Jan 7, 1960

By Fred N. Kissell

The new MSHA diesel rules have stone mine operators looking hard at pos¬sible upgrades to their ventilation systems. There are existing methods to reduce diesel engine emissions (MSHA, 2001)(Head, 2001b),but many operators will decide that a ventilation upgrade is necessary is well. NIOSH hay several stone mine ventilation projects underway, but in the meantime a good information resource is the work done by the U.S. Bureau of Mines in the 70's and 80's on ventilation for oil shale mines. The Bureau conducted this research because oil shale mines were projected to be gassy and would, therefore, require a lot of ventilation air. The focus of this oil shale work was on the use of jet tans for lace area ventilation, and on stoppings that would he low Lost and leak-tight. The work also considered changes in mine design to reduce the number and size of stoppings. The findings are still applica¬ble to stone mines.

Jan 1, 2002

By Robert T. Beckman

Education of inspection and operating personnel is essential to protection from radiation hazards in the mining industry. For over 10 years, MSHA has presented the only formal course on radiation measurements and control available to the mining community. Course objectives and content are described in this paper.

Jan 1, 1981

By M. A. Cocquerel

External process energy requirements and air pollution control regulations formulated to limit particulate and SO2 emissions are impacting on smelting and converting technologies and the corresponding process and secondary gas handling systems. This paper presents an overview of the different technical solutions used for cooling and dedusting the process gases in the different pyrometallurgical copper concentrate stages, including: drying, smelting, converting, slag cleaning and fire refining. The main principles of the process gas handling systems are presented &d a qualitative technical and economical comparison is discussed in relation to process changes, energy recovery and marketing or disposing of the various sulfur fixation by-products. Finally, a brief review of the methods for fixing sulfur contained in the process and secondary gases is presented.

Jan 1, 1999

By C. Stephan, E. Weiss, J. Trackemas, M. Sapko

The National Institute for Occupational Safety and Health (NIOSH), Pittsburgh Research Laboratory (PRL), in collaboration with the Mine Safety and Health Administration (MSHA), the mining industry and seal manufacturers, conducted a series of full-scale experiments within the underground experimental mine at PRL's Lake Lynn Laboratory. The purpose of the experiments was to evaluate the explosion-resistant characteristics of several new seal designs for rapid deployment during mine emergencies. These seals can be deployed in less than 12 hours and are capable of withstanding explosion overpressures in excess of 140 kPa (20psi). These novel seal designs use available mine materials, do not require conventional rib hitching and, most importantly, can substantially reduce exposure time for coal miners during sealing and mine recovery operations.

By Walther Mathesus

INTRODUCTION THE use of high blast heats on furnaces melting Mesaba ores is still the exception, the average blast temperatures carried on Mesaba stacks seldom reaching 1,100° F. Some 15 years ago, when the use of fine Mesaba ores in larger proportions to the total burden first came into practice, it was found difficult to employ even those blast heats which it had been possible to carry with the Old Range ores. The furnaces refused to "take" high heats, and would persistently labor with irregular stock movement, which impaired the practice and increased the coke consumption. By lowering the blast temperature, the working of the furnace became smoother, and experience taught that with the softer and more easily reduced Mesaba ores, satisfactory practice could be obtained with comparatively low blast heats. Therefore a large number of Mesaba furnaces have ever since been operated on very low blast temperatures, ranging between 800° and 1,000° F. In the face of these difficulties, furnace men were slow to recognize that furnaces could be so designed as to permit a free movement of the charges in combination with the use of higher heats. Since higher blast temperatures did not seem to offer great advantages in the smelting of Mesaba ores, investments in hot-blast stoves were not as attractive to the furnace man as labor-saving devices and means of obtaining greater tonnages. The effect of this preference is keenly felt at the present time. It has brought about the peculiar situation, that the majority of our furnace plants (among them some of the most progressive) lack modern and efficient stove equipment. The result is that, even where the proper furnace lines have been adopted and conditions are now favorable to the successful employment of higher blast temperatures, the heats required for the greatest fuel economy are not available.

Jan 3, 1915

By Davis A, Song J

A review of the literature indicated that several studies have been reported on the dissolution of gold using iodide/iodine, bromide/bromine leaching systems. Although the reagent costs are much cheaper for chloride/chlorine (or hypochlorite) this system has not been fully evaluated. This study was conducted to evaluate the fundamental chemistry of the chloride/hypochlorite leaching system. The CHEMIX program was used to model the stability of various gold species existing in the solution. The gold dissolution rate at different conditions was determined using gold strips immersed in various mixtures of chloride/hypochlorite. Leaching experiments were conducted to test the extraction of gold from various ores (oxidised and copper-gold ores), showing a promising prospect for this technique in various applications.

Jan 1, 1992

By P. Chris Pistorius

"Ilmenite smelting involves partial reduction of iron oxide from a slag consisting mainly of T1O2, T12O3 and FeO, yielding as products iron (with approximately 2% carbon) and titanium slag. Slag purity requirements preclude any fluxing additions, and the aggressive nature of the slag necessitates a furnace freeze lining. Large departures from thermal and chemical equilibrium hold in the smelter, with possible implications for process stability. The slag is approximately 150K. hotter than the metal, which means that the metal temperature is below the slag melting point; this difference in temperature has been shown to lead to formation of a solid TisOs-rich layer between the slag and metal. Recent equilibrium measurements have confirmed that the slag and metal are not in chemical equilibrium either, with significantly more reducing conditions in the metal than in the slag. After solidification, the pseudobrookite slag structure is metastable below approximately 1400K, and may transform upon slight oxidation.IntroductionThe natural mineral ilmenite is the main source of titanium, which is mainly used to produce Ti02-based pigments. Ilmenite has the ideal formula FeTiC>3, but natural minerals can be partially oxidized (to contain some Fe3+), and typically contain MnO and MgO as well, together with associated silicate minerals. Smelting is one of the methods to upgrade ilmenite for subsequent T1O2 pigment production; smelting involves partial reduction of FeO to form metallic iron as a byproduct and titanium slag as the main product. Reduction is typically controlled to yield a slag which contains around 10% FeO, 85% (Ti02+Tij03) and 5% impurity oxides (mainly MnO, AI2O3 and S1O2). An example of a typical average slag composition from reduction of South African ilmenite is shown in Table I. As this indicates, a significant side reaction is reduction of some T1O2 to T12O3. The relative extents of reduction of FeO to Fe and of Ti02 to T12O3 are such that the slag stoichiometry is close to that of the pseudobrookite phase [1]. Pseudobrookite has the structure AB2O5 (where ""A"" and ""B"" are different cation sites); the phase which makes up the bulk of solidified titanium slag has the AB2O5 structure and stoichiometry [2], and can be viewed as a solid solution of FeTi20s, T13O5, ÌçÔÀ2è5, MgTi20s, AI2T1O5 and C^TiOs [1]. This solid-solution phase is referred to as ""pseudobrookite"" or ""M3O5"" in this paper."

Jan 1, 2012

By L. A. Roe

Magnetic separation occupies an attractive position in the field of ore beneficiation. It is a simple yet effective method, used for some 150 years and steadily growing more important. This type of beneficiation orginated in 1792, when William Fullarton was issued a British patent covering the separation of iron ore by magnetic attraction. What is magnetism, and why are some materials capable of being magnetized and others not? The study involves many unknowns, and even a partial answer to these questions would be a dissertation in solid state physics and perhaps other fields of science. But the last two decades have revealed basic facts as to why certain materials are magnetic and what happens to them when they are magnetized.

Jan 12, 1958

By Mohab Sabry

Pile foundations are used extensively around the world to support both inland and offshore structures, including important structures such as nuclear plants and oil drilling platforms. The limit of the pile depth is currently predicted during the pile deriving process, given no chance for the designer to predict accurately the capacity of these piles prior installation. Furthermore, after pile installation, designer may not be able to modify the pile group design by increasing the number of piles and or changing the geometry of the pile group. This paper presents a numerical model for the case of single piles driven in homogenous sand using finite element technique and the theory of cavity expansion. The model is capable of simulating all the construction stages of concrete piles up to the maximum depth, which can be driven in sand and accordingly the capacity, which can be attained by these piles. The program "PLAXIS" is used to perform the proposed analysis. This model simulates the process of pile driving in terms of the changes in the earth pressure and the overconsolidation ratio acting along the pile's shaft. Based on the results of the present investigation, these depths can be predicted based on the pile geometry and the sand properties. Charts are given to provide these depths for given pile/soil conditions.

Jan 1, 2006

By Fraser RJ

A Robbins Raise Drill Model 61R was used to provide one 7' diameter shaft 1050' deep in Clutha Development's exploratory mine at Blackwater in Central Queensland and two 7' diameter shafts 1450' deep at their South Clifton mine on the Illawarra Coast of New South Wales.

Jan 1, 1972

Draglines are one of the largest land-based equipment moving across the earth. They typically ranging in size from2.5 to 6.5 kt (2,750 to 7,100 st). Their size, though, makes them difficult to maintain. Recently, G&S Engineering Services used an Enerpac synchronous hydraulic lifting system to lift a 3.2-t(3,500-st) dragline at the Curragh Mine in Queensland, Australia’s Bowen Basin.

Jan 1, 2004

By Bela Koman

Abstract - A shiploading terminal near Punta Arenas, the southernmost city of the world (lat. 53°-10'S, long. 70°-54' W) is described. Strong winds, choppy seas, frequent gales, rain, and snow make it difficult to load ships at an offshore berth in this area. Detailed site investigations, including a wind-recording program, supplied sufficient information for the analysis of operating conditions. The weather pattern of the entire region, including the predictability of gales, was utilized in the analysis. The results showed that a bulk loading terminal at this location is feasible, provided that the design takes into consideration the specific problems of the site. The final layout shows a terminal that can be approached from several different directions, depending on the direction of the wind. The mooring system is arranged to allow alter- native ways of attaching and casting off mooring lines and executing docking and departing maneuvers. The berth is supported on piles and contains the minimum of structures, relying on a slewing shiploader to reach the ship in any position, with only limited fore and aft shifting of the vessel for loading the extreme hatches. Results of wind recording, statistical analysis of wind and wave data, operating criteria, and the results of berth availability analysis are included in the paper.

Jan 1, 1987

By Andrew L. Mular, Richard R. Klimpel

Optimization strategies of possible interest to mineral processing are reviewed and typical strategies initiated in processing plants to date are discussed. Both On-Line and Off-Line optimization procedures have been employed by industry, assisted either by operators or by digital computers. In every case, dollar benefits have accrued.

Jan 1, 1991

By A. E. Harnsberger

IT is obvious that details such as the physical and chemical properties and methods of heat-treating of the materials mentioned must be omitted in a paper on the subject of materials used in oil-refinery pumps1. Only sufficient identification is given to enable the reader to find additional information from already published data. Also, the subject covers many operating conditions, but only the most important services can be discussed here. To the oil refiner, the pumping equipment is of vital interest. Practically every refinery operation, from the charging of crude oil to a distillation unit to the shipping of refined products, involves some form of pumping machinery. Intermediate refining stages involve a great variety of pumping machinery to carry out successfully the aims of the refinery technologist. Temperatures at which oils are handled vary from -50° F. to 900° F. Pressure may vary from subatmospheric to 2000 lb. per sq. inch. The selection of the proper materials involves a careful consideration of the conditions under which the particular pump must operate. The four, most important considerations are temperature, pressure, corrosion, and abrasion or wear. Consideration of temperature may be divided into three parts: (1) extremely low temperatures of the order of -50° F.; (2) temperatures at atmospheric or slightly above; .(3) temperatures from 200° to 900° F. Pressures fall into two groups: (1) pressures reached by ordinary trade pumps of the order of. 200 lb. per sq. in., (2) extreme pressure conditions involving pressures as high as 2000 lb. Noncorrosive and corrosive oils can be treated differently. Under the latter falls corrosion in the presence of water, which will occur up to 250° F. The second type of corrosion occurs in high-temperature pumping equipment, with temperatures from 450° to 900° F., largely caused by sulfur compounds. There are also other corrosive conditions met with

Jan 1, 1935

By R. G. McDonald

"High iron solution concentrations often result in the formation of basic ferric sulfate during the high temperature oxidation of sulfidic materials such as base metal and refractory gold concentrates. Consequently, the “Hot Cure Process” followed by limestone neutralization is required to facilitate subsequent processing and/or disposal of the leach residue. The present paper discusses strategies that can be employed to influence the composition and nature of the high-iron content leach residues produced during pressure leaching.INTRODUCTION Control of iron deportment in hydrometallurgical processing remains a key challenge for a range of reasons. Strategies generally relate to the control of conditions under which iron is optimally rejected (Demopoulos, 2009). Supersaturation provides the driving force for crystallization and this can be controlled by a number of factors that include (1) pH and/or Eh control, (2) the presence of matrix anions and impurities, (3) dilution, (4) complexation and dissociation and (5) manipulation of the rate at which the metal to be precipitated is released to solution. Each of these factors is impacted by temperature. Good control of crystallization is essential to the control of precipitate properties such as the degree of crystallinity, stability, particle size and quality which covers both the extent of impurity uptake and suitability of the precipitate for waste disposal. The quality and properties of iron precipitates in turn can impact downstream processing. It is the aim of this paper to discuss the generation of iron-containing residues produced during the pressure oxidation of sulfidic ores and concentrates and how the nature of these can be controlled to potentially facilitate further processing. A brief overview of several related topics will now be given and include, where relevant, discussion of work undertaken in our laboratories. In addition, brief discussions of selected process options that enable good control of iron rejection will be provided."

Jan 1, 2016

By Philippe Ribagnac, Bruno Courtaud, Jean-Marie Lambert, Valérie Weigel

Mabounié is a polymetallic deposit in Gabon containing niobium (1.2 wt.%), tantalum (0.03 wt.%), rare earth elements (REE) (1.4 wt.%) and uranium (0.03 wt.%) that are mostly carried by pyrochlore minerals. The classical route for niobium recovery is a pyrometallurgical process that consists of pyrochlore flotation, dephosphorization of the niobium concentrate and aluminothermy to obtain ferro-niobium. Pyrochlore concentrates can also be treated by a hydrometallurgical process with a mixture of sulfuric and hydrofluoric acid leaching followed by solvent extraction to separate niobium and tantalum. However, the first process does not allow recovering REE and the second one is not environmentally friendly because of the use of HF. ERAMET is looking for new opportunities on strategic metals market and has recently developed a hydrometallurgical process for the recovery of all these metals based on a sulfuric acid treatment of the ore (Donati, Courtaud, & Weigel, 2014). As for most of the oxidized ore processes, the major impurity is iron (~30 wt.%). Thus, in this hydrometallurgical process, the question arises of the elimination and stabilization of the iron as residue. The iron in solution is ferrous; goethite precipitation seems the most adapted crystalline form. Lab and pilot tests have shown kinetics of precipitation of 6 g.L-1.h-1 at pH 4.5. To reduce the salt discharge, sodium-jarosite form is more adapted, but at pH 2, 95°C only 30% of iron is precipitated in 5 hours, compared to 100% in goethite form at the same time and pH 2, 80°C. Different ways of oxidation were tested, air, pure O2, activated carbon, without drastic effect. The more efficient was ozone use, at room temperature; the kinetics of oxidation is five time faster than the other ways with 30% of sodium removed from the solution.

Jan 1, 2016

By S. W. Miller

DURING the examination of welds made in steel by the oxy-acetylene and electric-arc processes, the writer has met with some unusual structures, which he has not encountered elsewhere. They seem to be quite closely associated with the welding methods used, and characteristic of them, and would seem to be worth noting, especially as the references to them in the literature are few, and their explanation not clear or complete. An introductory word or two about fusion welding may not he out of place. The oxy-acetylene process is based on the great and very local heat generated by the burning of acetylene in the presence of commercially pure oxygen, the two gases being thoroughly mixed before combustion. The theoretical temperature is somewhat under 4000° C., but on account of various losses, the actual maximum temperature is probably about 3000° C. 1 The electric-arc process, using a metal electrode, which is also the filling rod, generates a still higher and more local temperature. The actual temperature of the positive crater of the carbon arc is given as 3500° C.2 No figures have been found for the temperature of the arc using a metal electrode, but it would probably not be very different from that of the carbon arc, and probably higher than that of the oxy-acetylene flame. The greater localization of the electric arc is due to the fact that it is not surrounded by a large envelope flame as well as to its higher temperature; while the oxy-acetylene white cone, or welding flame, in which the carbon of the acetylene is burned to CO, is surrounded and preceded by -a long envelope flame, itself of quite high temperature, in which the CO is burned to C02, and the hydrogen of the acetylene to

Jan 2, 1918

By X Liu

The crystal chemistry of carbonate in Ca apatites, including Na-free and Na-bearing hydroxylapatite (CHAP) and Na-bearing fluorapatite (CFAP) and chlorapatite (CCLAP), has been investigated by Fourier transform infrared (FTIR) spectroscopy and single-crystal X-ray structure, using crystals synthesised from carbonate-rich melts at 1 GPa, 1400 - 1000¦C. The carbonate ion substitutes for both the X (OH, F, Cl) anion species in the apatite channel (type A carbonate) and the phosphate group (type B carbonate). The type A carbonate ion is oriented in the channel with two oxygen atoms close to the c-axis, and the type B carbonate ion is located close to the sloping faces of the substituted phosphate tetrahedron, with details varying with composition series. Sodium promotes the uptake of type B carbonate and also has a profound effect on FTIR spectra. Crystal compositions correspond approximately to the substitution formula Ca10-(y+z)Nay z[(PO4)6-(y+2z)(CO3)y+2z][X2-2x(CO3)x], with x + y up to 1.0 and z + 0.0 for CHAP, x + y + 4z + 0.4 for CCLAP, and x + y + 2z + 0.1 for CFAP, for equivalent conditions of synthesis. The sodium cation and A and B carbonate ion defects are locally coupled in all three composition series to facilitate charge compensation and minimise the effects of spatial accommodation. Synthetic Na-bearing type A-B CHAP with x + y + 0.5 has a similar chemical composition and FTIR spectrum to biological apatite.

Jan 1, 2008