Search Documents

By R. H. Kudlich

In order to assist the various Federal and State agencies using large quantities of coal to select coal best suited technically and economically to their use, the United States Bureau of Mines has placed at their disposal a fuel inspection service. As part of this service, inspections are made at the mines which propose to furnish coal to these agencies on contracts. Such inspections cover both the mine itself to ascertain its capacity to fur- nish the desired tonnage and quality of the coal, the preparation of the coal in the tipple, and the obtaining of samples for analysis to determine the quality of coal as shipped. To insure that the sample sent to the laboratory for analysis is representative of the average quality of the coal, increments are taken at intervals until a gross sample of about 1,000 pounds of coal has been collected from each of the sizes of coal shipped by the mine, while coal has been coming from all parts of the mine. In reducing this gross sample to the small sample which is sent to the laboratory for analysis it is necessary to crush and quarter the coal by a certain standardized method until only 5 or 6 pounds of coal small enough to pass through a 3/16-inch square-mesh screen remains. The ordinary method which the bureau has followed was to crush the coal by hand with a tamper, such as is used for tamping concrete, on some hare smooth surface and to reduce the volume by quartering and riffling. During the past few years the demands from various Federal and State agencies for this service have been increasing rapidly in respect to bituminous coals. In addition to this, which might be called the normal increase, numerous requests have been received for similar service in respect to anthracite. It was obvious that if this increased demand was to be met it would be necessary either to increase the force allotted to this work or to provide the present force with some means by which their work could be made more effective. A care- ful survey of the situation showed that the greatest amount of time was consumed in trans- porting the men and their equipment from mine to mine in the same district, and in reducing the gross sample to the small finely crushed sample which is to be sent to the laboratory. Both of these phases of the work could be greatly accelerated by providing a motor truck of suitable speed and capacity, carrying a power-operated crusher, and the proper auxiliary equipment to store the gross sample as collected and to reduce it in volume efficiently after it has been crushed. Such a truck has been provided and placed in service. In the eight months it has been in operation the desired results have been fully attained. About twice as many samples as usual have been taken during that time by the same 2-pan crew assigned to this work. Many of the mines in the eastern part of the United States are in hilly or mountainous regions and can be reached only over rough, practically unimproved roads. Hence the speci- fications for the truck were drawn to cover high-quality, long-life trucks, in order that

Nov 1, 1931

By Edward C. Stephens, Robert R. Coats

High-grade copper ore was discovered in 1932 in the long-dormant Mountain City (Cope) mining district, Elko County, Nevada. From 1932 to 1947, the one producing mine in the district, the Mountain City Copper Mine, produced 1,109,878 short dry tons of ore averaging 9.745 per cent copper, 0.274 ounces of silver, and 0.0057 ounces of gold per ton. The Mountain City Copper Mine is developed in eugeosynclinal rocks of Ordovician age, the Valmy Formation, which is part of the upper plate of the Roberts Mountains thrust. On the Valmy were deposited unconformably first, a elastic formation of Devonian or Mississippian age, the Grossman Formation, succeeded unconformably by a ·sequence of three conformable formations, the Banner, the Nelson, and the Mountain City. The Banner Formation probably is early Late Mississippian in age; the ages of the Nelson and Mountain City are not known precisely but are believed to be of Late Mississippian and Carboniferous(?) age, respectively. A thick formation of elastic rocks, limestone, and volcanics, the Reservation Hill Formation, has been thrust over the Mountain City. The age of the Reservation Hill is unknown but is presumed to be Pennsylvanian(?) and Permian(?). Several plutons of Cretaceous quartz monzonite intrude the Paleozoic formations; they and the intruded formations have been laid bare by erosion, and several sequences of volcanic rocks of Miocene and Pliocene age, and perhaps in part older, have been successively deposited on irregular erosion surfaces. The primary mineralization of the Mountain City Copper Mine is believed to postdate the deposition of the Nelson Formation and to predate the intrusion of the quartz monzonite. The primary ore bodies are lenticular in shape and are composed largely of quartz, pyrite, and chalcopyrite. The ore lenses, in general, strike northwestward and dip northward. They occur in the Valmy Formation within a definite stratigraphic sequence composed largely of shales with associated minor quartzite lenses. The ore is epigenetic. The principal ore body, the "200," was completely leached to the 200 level. Abruptly beneath the barren gossan was supergene copper sulfide ore, much of which assayed 50 per cent copper. The secondary copper minerals are sooty and massive chalcocite, bornite, and covellite. The supergene enrichment of the ore may have required a large part of Tertiary time.

Jan 1, 1968

By W. O. Karvinen

"In the Timmins area, a close spatial and chronological association exists between gold deposits and two major stratabound carbonate-rich members and related quartz-feldspar porphyries. Synvo/canic and metamorphogenic are the two main types of mineralization recognized. Synvolcanic ores include the stratiform quartz-ankerite ""veins"", pyritic carbonates and chert-carbonate-tuff sedimentary rocks and epigenetic ventrelated breccias and stringer zones. Metamorphogenic ores consist of quartz-carbonate fracture fillings in dilatant zones developed during various phases of regional deformation and metamorphism. They are classically epigenetic in character.The evidence suggests a primary syngenetic enrichment of gold on the ocean floor and in vent areas during submarine felsic volcanism and related exhalative-hydrothermal activity followed by further enrichment into quartz-carbonate stockworks during regional deformation and greenschist metamorphism.Although normally thin (a few hundred metres), carbonate members in Archean volcanic terrain represent intense hydrothermal activity which could have transported and enriched gold. They should be used to locate fossil vents and structurally favourable zones where economic concentrations of gold may be found."

Jan 1, 1982

By C. R. Kato, G. Proulx

"Within the continuous scenario of reduced aluminium price and plants production costs increase, the energy consumption optimization in the aluminum electrolytic pots continues as the main focus for the producers. Energy consumption was chosen as a key performance indicator to drive the efforts and actions for improvements. Alcoa improved the energy consumption by approximately 3% from 2005 to 2015. This improvement was a result of best practices implementation, new technologies introduction, strategic actions with plant curtailments and management practices. The main objective of this paper is to highlight the importance of the management practices for planning and operational improvements beyond the technology changes. About 10 years ago, Alcoa reorganized its approach to retain knowledge in the Smelters by using a Best Practices format. For each specific subject, a skilled team defined the minimum requirements and the Best Practices for several aspects of operation and maintenance, which affect the environment, safety, cost, customers and performance. These Best Practices were deployed to all Smelters combined with training sessions to process and operation professionals. We will describe how the Best Practices were organized, the deployment strategy used, and the approach to measure the plants’ success. We will describe the management approach that includes Manufacturing Analyses focused on 3-year potential, annual planning, and weekly monitoring of plant stability. A manufacturing analysis is organized at select plants with cross-functional participation of specialists from technical, operational, procurement and finance. The output of a manufacturing analysis includes a roadmap of enablers to improve energy efficiency. A quarterly follow-up of enabler deployment is held with the plant and resources that participated in the analysis. Annually, there is a Planning Process where energy consumption enablers are selected to be implemented during the next 3 years for each plant. A monthly critical analysis is made by the plants with regional best practice support. On a weekly basis, key performance indicators are reviewed with determination of a stability index for each plant. Any deviation signal of unstable condition is alerted and supporting resources are diverted to the plant to reverse trend with countermeasures.INTRODUCTIONDue to factors like excess aluminum in the market and lower consumption in China, the LME price is declining along the last years, as showed in Figure 1. In 2011, the price peaked at US$ 2,400/ton and since then, continues to trend down and approaching the lowest level at US$ 1,500/ton in the last 5 years."

Jan 1, 2016

By William Gleason

"The Colorado School of Mines has used the Edgar Mine in Idaho Springs as an experimental mine to teach students since 1921. Since the school acquired the former gold, silver, lead and zinc mine, countless students have received hands-on engineering lessons on their way to earning mining engineering degrees. On Dec. 14, the House Subcommittee on Energy and Mineral Resources held a historic field hearing about the future of mining education in the United States in a classroom about 300 m (1,000 ft) inside the Edgar Mine. Representatives Doug Lamborn (R-CO), Rob Bishop (R-UT), Cresent Hardy (R-NV) and Ed Perlmutter (D-CO) were on hand for the first ever congressional hearing held in a mine where they heard testimony supporting the Mining School Enhancement Act, which was introduced to Congress by Hardy and Perlmutter on Oct. 9, 2015. The act, which is part of a larger mining development and reclamation reform package, seeks to address the absence of a viable pipeline necessary to replenish current faculty vacancies in United States Mining Schools. “What better place to hold a hearing to discuss the need for future mining engineering experts,” Subcommittee Chair Lamborn said in his opening statement. “It is a need felt by industry, states, the federal government as well as nonprofits.” The Mining School Enhancement Act would redirect millions of dollars in fees that are being collected from active mining operations to fund the research and educational programs at engineering schools with mining programs. Those fees now are being used in the form of grants awarded by the Surface Mining Control and Reclamation Act of 1977 (SMRCA)."

Jan 1, 2015

By Gordon G. Duncan

Historical Sketch Occurrences of native copper have been known along the Arctic coast of Canada, especially in the vicinity of the. Coppermine river, since the early part of the eighteenth century (See map, Figure 2, insert). In 1769, Samuel Hearne, a clerk of the Hudson's Bay Company at Fort Churchill, was sent to explore the 'copper mines' from which natives had been reported to secure copper for tools, fishing spears, etc. After two successful attempts, he reached the Coppermine river in 1771, accompanied by Indian guides. This hazardous trip was indeed a remarkable feat when one considers the vast distance covered, a great deal of which was barren lands. At Bloody falls, (See Figure 1) on the Coppermine river, Hearne's Indians swooped down on a party of sleeping Esquimaux, who gathered there each summer to fish, and murdered the entire band encamped on that side of the river. Hence the name of the falls. Hearne's knowledge of minerals was undoubtedly limited. He reported having seen the copper mines from which the natives were securing the copper, but he failed to prove the economic possibilities of the copper occurrences or to give an accurate description of any deposit. Sir John Franklin visited the area in 1821. He and other members of his expedition, namely, Richardson, Back, Kendall, and Hood, reported native-copper float to occur in the vicinity of the Coppermine river and Bathurst inlet.

Jan 1, 1931

For 11 years, under authorization of the Synthetic Liquid Fuels Act of April 5, 1944 (30 U.S.C. 321-325), and amendments, the Bureau of Mines has carried on an extensive research and development program to establish methods for producing oil from coal and from oil shale. This act was passed by the 78th Congress primarily because of the stress of wartime demands for liquid fuels to supply our armed forces during World War II. The act was progressively extended by the 80th and 81st Congresses, as later peace-time demand for oil and oil products continued to increase.

Jan 1, 1956

By H. B. Jensen

STUDY of the thermal-solution process was begun by treating crushed oil shale in a small autoclave at temperatures of 700° to 950° F. The effect of temperature, reaction time, type of solvent, and richness of shale upon the amount of organic matter that was removed from the oil shale was thus determined. Following this orientation work a semicontinuous, bench-scale apparatus was built so that heated solvent could be pumped through a bed of shale under elevated pressure, thus removing the converted organic matter from the spent shale. After some operating experience had been gained, a continuous unit was constructed. This permitted treating a slurry of shale oil and pulverized oil shale at about 300 p. s. i. and temperatures of 750° to 850° F. for various retention times. Considerable cracking and polymerization of the shale oil were found to take place during the process. In an attempt to prevent this, a study was made of extraction of the shale in batch-type autoclaves under high partial pressures of hydrogen at total gas pressures of as much as 4,300 p. s. i. at 850° F. The thermal-solution process was found to convert over 90 percent of the organic matter in oil shale to oil and gas. The highest yields of gas and oil obtained without hydrogen pressure were equivalent to 119 weight-percent of those obtained from the same shale by Fischer assay. With a high partial pressure of hydrogen, yields equivalent to 126 weight-percent of Fischer assay were obtained. However, the oil produced by thermal solution has a higher boiling range than that obtained by other retorting methods, particularly so if the thermal-solution process is used without a high partial pressure of hydrogen. Nondistillable oil (all benzene-soluble material that would not distill under 2 mm. Hg absolute pressure without cracking) equivalent to over 100 percent of the organic matter in the shale was obtained without hydrogen pressure in the system. When the process was carried out under hydrogen pressure, the yield of nondistillable oil amounted to 60 to 70 weight-percent of the organic matter. Part of this heavy material is formed partly by polymerization and condensation of the shale-oil solvent used. These reactions, as well as cracking of the solvent to form gas and a carbonaceous deposit on the shale, are unfavorable features of the process.

Jan 1, 1953

*J. H. Brennan, Union Carbide Metals Company, Niagara Falls, N. Y. S. B. Casey, Jr., Swindell-Dressier Corporation, Pittsburgh, Pa. C. M. Cosman, Vanadium Corporation of America, New York, N. Y. H. E. Dunn, Vanadium Corporation of America, New York, N. Y. C. S. Finney, Eastern Gas and Fuel Associates, Boston, Mass. M. O. Holowaty, Inland Steel Company, East Chicago, Ind. John Mitchell, Eastern Gas and Fuel Associates, Boston, Mass. Leo F. Reinarts, Armco Steel Corporation, Middletown, Ohio H. E. Rowan, Dwight-Lloyd Division, McDowell Company, Inc., Cleveland, Ohio R. W. Shearman, The Metallurgical Society of AIME, New York, N. Y. C. M. Squarcy, Inland Steel Company, East Chicago, Ind. F. Weston Starratt, The Metallurgical Society of AIME, New York, N. Y. A. B. Wilder, National Tube Division, United States Steel Corporation, Pittsburgh, Pa. *Deceased

Jan 1, 1961

By P. A. Neill, O&apos

The caisson foundation for Vent Building No. 6, at the southern landfall of Boston's Third Harbor Tunnel, was installed inside an unbraced concrete cofferdam 250 feet in diameter and about 70 feet deep. As a spectacular engineering feat, the cofferdam itself certainly ranks first. However, the foundation work within was no routine caisson job and made its own contribution to the state of the art. Comprised of 5 ft. diameter caissons socketed 10 to 16 feet in sound rock, it posed serious challenges in logistics, space limitations and time, requiring development of unique, purpose-made equipment. The unexpected discovery of significant depths of shattered rock overlying acceptable sound rock, along with other surprises of lesser import, compounded the problems. How these challenges were planned for, met and overcome is the subject of this paper.

Jan 1, 1994

By I. V. Filippova, Y. Foucaud, M. Badawi, O. Barrès, L. O. Filippov, S. Lebègue

Sodium silicate (Na2SiO3) is one of the most common reagents used in the froth flotation process, in which it is an efficient dispersant as well as a powerful gangue minerals depressant. Due to its high affinity with a lot of minerals, mostly silicates, it adsorbs on their surfaces and prevents the adsorption of the collectors, maintaining them hydrophilic. Hence, Na2SiO3 is widely used in the flotation separation of rare earth minerals, zinc minerals, iron minerals, scheelite, fluorite, apatite, and many other minerals. For decades, authors have demonstrated higher efficiency of Na2SiO3 when it is used in combination with sodium carbonate (Na2CO3), a common pH regulator. Among many well-known depressants, this system presented the best efficiency for many ores, including the Tabuaço scheelitebearing skarn studied herein. However, the mechanisms resulting in these strong positive synergistic effects are not well understood at the moment. Hence, the response surface methodology (RSM) was applied to this ore, considered as a case study, to optimize the depressing conditions and to study deeply the flotation behavior of this system. Strong synergistic effects between the two reagents were exhibited by the RSM, mostly affecting the scheelite, fluorite, and calcium-bearing silicates recoveries. This was attributed to surface carbonation of the minerals by Na2CO3, subsequently leading to a better depression by Na2SiO3. Overall, a 1:1 ratio between the two reagents displayed the best results in terms of WO3 grade and recovery. To gain understanding in the molecular mechanisms responsible for the aforementioned synergistic effects, FTIR studies were combined with state-of-the-art molecular modelling (Ab Initio Molecular Dynamics at 300 K) on fluorite, an archetype of calcium minerals. Keywords: Synergistic effects, scheelite, depressants, FTIR, DFT calculations

Jan 1, 2020

By Sidney Katell, JOHN H. FABER, BRYCE L. MADDOX

The information abstracted from the various publications appeared in the magazines under such headings as Business and Industry , Chemical Engineering Developments , Companies in the News , Headlines of the Month , Industrial News , Industry , Refining and Gas - Processing News , Refining News , What's Happening , and others . Although most items are related to chemical and petroleum plants , a few pertain to related fields , such as markets , drilling costs for petroleum , and field prices of crude oil . Certain articles discuss various aspects of cost -estimating procedures or description of processes . Cost bibliographies prepared by other groups are discussed in items 70 and 271. The two references can be considered as supplemental to this report , since the amount of overlap in the contents is insignificant .

Jun 15, 1957

By T. R. Rehak

Blasting operations are an essential element in the recovery of our Nation?s mineral resources. The mining industry uses billions of pounds of explosives annually. The majority of blasting occurs in surface mining operations. Blasting results in the fragmentation and often the projection of rocks. Frequently, the rocks are thrown beyond the expected limits. Flyrock and failure to secure the blasting area dominate blasting-related accidents in mining, especially in surface mining. Blasting accidents in the mining industry tend to result in critical injuries or fatalities. Accident reports and information collected from the Mine Safety and Health Administration (MSHA) and other government agencies provide supporting evidence. According to the data collected, blasting-related accidents (in mining) were 11 times more severe than all other types of mining accidents. Blasting accidents are not unique to mining operations - the same situation exists in the construction field. In this paper the authors have compiled a list of the primary causes of flyrock and the failure to secure the blast area. In the next phase of this project, typical blasting scenarios will be reviewed which will highlight the main reasons flyrock and/or lack of blast area security occur. This will alert miners and construction workers to the current problems/hazards associated with blasting and to identify other safety measures to protect personnel.

Jan 1, 2000

By A. J. Kraemer

This paper is the third and concluding report of the results of the United States Bureau of Mines twenty-third semiannual survey of motor fuel marketed in the United States. The first paper, reporting data relative to gravity, vapor pressure, and distillation range of the samples, was published as Report of Investigations 3129. The second report dealt with the data of the twenty-third survey in accordance with the revised specifications for United States Government Motor Gasoline. These data were published as Report of Investigations 3142.

Jan 1, 1931

By A. J. Kraemer

This paper is the third and concluding report of the results of the United States Bureau of Mines twenty-third semiannual survey of motor fuel marketed in the United States. The first paper, reporting data relative to gravity, vapor pressure, and distillation range of the samples, was published as Report of Investigations 3129.7 The second report dealt with the data of the twenty-third survey in accordance with the revised specifications for United States Government Motor Gasoline. These data were published as Report of Investigations 3142.8

Jan 1, 1931

By Irving Wender

This report describes Bureau of Mines experiments and reviews the work of others on the exposure of coal and coal-derived products to gamma rays and some other types of radiation. Results are presented on tests of three bituminous coals and a lignite that had been pulverized to minus 200-mesh particles and exposed to 1,000 megaroentgens of gamma irradiation from spent-fuel elements of a nuclear reactor. Of about 20 chemical and physical tests in Bureau work, only mass spectrometry of gases evolved during vacuum pyrolysis of the coals to 450° C gave results indicating differences in the irradiated and unirradiated samples. Mass-spectral distribution curves for CO and CO2 evolution showed fewer irregularities (reversals of curvature) for irradiated coals; thus, mass spectrometry appears to be the most sensitive method for determining radio-induced changes in coal. It is concluded that coal is not significantly altered by gamma irradiation owing to the resistivity of its highly condensed ring structure. High-level gamma irradiation, therefore, is unlikely to prove advantageous in coal processing and utilization. Specially treated coals, because of resistivity of coal to radiation damage, may be useful as an absorbent in processing radioactive wastes.

Jan 1, 1968

By C. H. Hopper

THE gold orebodies of the Matachewan Consolidated mine are of particular interest geologically because of their odd shapes, their apparent lack of connection one with another, and the fact that they occur in a number of different formations. All of the orebodies exhibit a similar fracture pattern and the areas of fracturing appear related to the local folding. However, the lack of either horizontal or vertical continuity suggests additional controls not yet discovered. The question of origin, so ably discussed by H. C. Cooke in 1919, will be reviewed in the light of the additional evidence uncovered since his examination of surface trenches twenty-four years ago. The Matachewan Consolidated mine, with its neighbour, the Young-Davidson mine, is in Powell township, 25 miles by road northwest from Elk Lake, 30 miles west of Kirkland Lake, and 45 miles southeast of Porcupine. It may be considered as being on the westerly extension of the Kirk-land Lake sedimentary belt, where the rock column is markedly similar. There is no similarity in structure, however, for great ore-bearing shears and faults simply do not occur at Matachewan. Rather may it be said that the region, under stress, failed in isolated brecciated patches, some of which make up today's orebodies. The mine currently treats 1,000 tons a day of porphyry ore averaging 0.10 oz. gold per ton. It started operations in 1934 on greenstone ore, and the mill then treated 150 tons a day of ore averaging 0.23 oz. gold per ton. Total production to the end of 1941 has been 929,484 .tons averaging 0.160 oz. gold per ton.

Jan 1, 1942

By C. T. Harper, B. J. Fryer, R. P. Taylor

"IntroductionThe Maurice Bay deposit is one of a number of uranium deposits that have been found in recent years in the Athabasca Basin of northern Saskatchewan (Tremblay, 1982). This deposit, along with the others, belongs to the unconformity type deposits (Beck, 1977). They are, for the most part, polymetallic, being characterized by a suite of metals which include U, Ni, Co, Cu, Pb, Zn, Mn, V, Ag, Au, Pt-group elements, S, As, Bi, Se, Te, and Mo, some of which, besides U, are present in economic concentrations (Amok, 1974; Ruzicka, 1975; Tapaninen, 1976; Hoeve and Sibbald, 1978; Dahlkamp, 1978). The Maurice Bay deposit was known to be a small low grade deposit in which the ore was essentially monomineralic, consisting mainly of pitchblende (Harper, 1978). However, the occurrence of trace amounts of some of the elements common in the larger polymetallic ore bodies (e.g. Key Lake, Cluff Lake D) was anticipated. Thus a lithogeochemical sampling project was undertaken in 1979 across part of the Maurice Bay deposit (Harper, 1979). Major oxides (SiO2, Al2O3, FeO, Fe2O, MgO, CaO, K2O, Na2O, MnO, P2O5, and TiO2) and a group of the most common trace metals (U, Ni, Co, Cu, Pb, As, Au, V, and Se) were analyzed to determine whether any elemental patterns (halos or depletions) could be detected which would reduce the number of pathfinder elements needed for exploration purposes. In addition to the above metals, Th was also checked because some conglomerate strata in the Maurice Bay area are known to be thorium-enriched (Harper, 1978). Only the trace metal distributions will be discussed in detail in this report.General GeologyThe Maurice Bay area is underlain by three major groups of rocks, the White Lake metamorphic complex, an unnamed granodiorite complex, and the Athabasca Group, described previously (Fig. 1; Harper, 1979). Table 1 summarizes the stratigraphic features as deduced by geological mapping and the examination of drill cores."

Jan 1, 1986

By R. R. Hornor

BIBLIOGRAPHY OF ARTICLES RELATING TO THE PRESERVATION

Apr 1, 1922

By D. C. Dahlin

To identify and characterize potential domestic chromium resources, the Bureau of Mines investigated podifom chromite deposits along the Border Ranges Fault in southern Alaska. Part 1 of this two-part report describes an extensive field investigation and preliminary resource evaluation studies by the Bureau's Alaska Field Operations Center. This paper, part 2, describes the mineralogy of 38 samples that were collected from low-grade deposits in the Chugach Mountains, on the Kenai Peninsula, and on Kodiak Island, and presents the results of laboratory batch beneficiation tests designed to concentrate the chromite. The samples are peridotites and chromites that consist primarily of variable amounts of chromite, olivine, and serpentine. They were beneficiated by a sequence of grinding, sizing, and gravity concentration operations. Twenty-four high-chromium or marginal high-chromium chromite concentrates, six high-iron or marginal high-iron chromite concentrates, and five submarginal concentrates were produced with chromium recoveries that ranged from 37 to 95 pct. Three very low-grade samples were not beneficiated. These results indicate that several of the de- posits may be significant chromium resources, Potential precious metals association with the chromite was also investigated. Analysis of these samples indicates that the chromite deposits are not good platinum sources.

Jan 1, 1985