Search Documents

By J Brown, C Roberts

The scope of this paper is to recount the development of segmental linings used in tunnel construction, starting with its inception as an improvement to the brick-lined tunnel approach of Brunel in England and moving through the history and development to the present day, before finishing with a few insights into what the future might hold. The paper also discusses the motivation for the relatively recent move towards replacing conventional steel reinforcing cages with steel fibres and the reasons why steel fibre reinforced concrete (SFRC) is rapidly becoming the material of choice for manufacturing precast concrete segmental linings.

Jan 1, 2008

By N. Morrison, E. J. Rogans, A. J. Macintosh, N. Schoeman

"The design of carbon-in-pulp (CIP), and carbon-in-leach (CIL) adsorption circuits has essentially remained unchanged since the early days of the carbon process for gold recovery. For CIP circuit the pulp residence time is traditionally fixed at one hour per contactor with a carbon concentration of between 15 and 20 grams per litre, and the counter current carbon transfer rates are in the region of 15% pulp recycle. For CIL, the pulp residence time is usually three hours per contact or, with lower carbon concentrations ( 5 to 10 grams per litre).The drawbacks of using the counter current CIP/CIL adsorption circuits are discussed using modeling developed for CIP/CIL plant design. Counter current CIP/CIL, circuits are then compared with the carousel method of adsorption circuit design.The use of equipment suitable for the carousel approach is discussed which is, the AAC cylindrical and pumping (MPS) screens, the AAC pump-cell plant and launder designs.Finally, two plants at the Vaal Reefs Gold Mining and Exploration Company that use carousel adsorption circuits, namely the Vaal Reefs No. 1 Gold Plant, a CIL plant with stepped contactors, and the Vaal Reefs No. 2 Gold Plant, a CIP using a very short residence time (AAC pump-cell) are discussed."

Jan 1, 1998

By S. O. Choi, C. Park, C. Sunwoo

Two methods of stress measurements have been executed on the surface and underground to con-struct an oil storage cavern using hydro-fracturing and overcoring method. The first measurement has been performed to make a design of the caverns before excavating and the second to confirm the stress state during excavation. Six measurements have been carried out in the hydro-fracturing test at the depths between –17.8 and 54.5m from the sea level and a single measurement in the overcoring test in a single borehole at the depth of –21m from the sea level. The ratios of the maximum horizontal to vertical stress measured using hydro-fracturing and overcoring method are 2.95 and 3.1, respectively. Also, the orientations of the maximum horizontal stress are N53E and N58E. These measurements show that both methods give almost same results and significant horizontal stresses are acting on this cavern. Deux méthodes de mesure de contrainte ont étè exécutées sur la surface de terrain et sous la terre pour construire une cavité de stockage de pétrole en utilisant l’hydro-fracturing et l’overcoring. La première mesure a étè faite pour le plan des cavités avant l’excavation et le seconde pour con-firmer l’état de contrainte durant l’excavation. Six measures ont étè faites dans le teste de l’hydro-fracturing à la profondeur entre –17.8 et 54.5m depuis l’élèvation maritime. Une seule mesure a étè faite dans le teste de l’overcoring dans une seule trou de songdage à la profondeur de –21m. Le ratios de la maximale contrainte horizontale à la contrainte verticale mesure par les deux méthodes sont 2.95 et 3.1, respectivement. Les orientations de la maximale contrainte horizontale sont N53E et N58E. Ce montre que les deux méthodes donnent presque m me résultats et la contrainte im-portante est activée sur ces cavités. Zwei Druckmessungen wurden durchgeführt auf der Erdoberfläche und im Innern von Ölspeicher-kavernen unter vergleichender Anwendung des Hydrofraktionierungs- und des Kernbohrungsver-fahrens. Die erste Messung wurde durchgeführt um einen Plan der Kavernen vor der Herstellung zu erstellen und die zweite um die Druckverhältnisse während der Bohrung zu überprüfen. Sechs Messugnen wurden mit der Hydrofraktionierungsmethode bei einer Tiefe von 17,8m und 54,5m unter dem Meeresspiegel und eine einzige Messung mit der Kernbohrungsmethode in einem Bohr-loch bei einer Tiefe von 21m unter dem Meeresspiegel vorgenommen. Das Verhältnis von maxi-malem horizontalem zu vertikalem Druck bei der Hydrofraktions- und der Kernbohrungsmedthode ist 2,95 bzw. 3,1. Die Bezugspunkte des maximalen horizontalen Drucks in beiden Verfahren sind N53E und N58E.

Jan 1, 2003

By A Mcquillan, N Bar

Geotechnical models developed during the open pit mine planning stage are generally three-dimensional (3D) in component to capture the spatial variation in geological, structural, hydrogeological and geomechanical conditions. Yet when geotechnical analysis is completed, often the 3D geological, hydrogeological and structural models are simplified to two-dimensions (2D). This paper demonstrates this simplification, through referenced case studies, can lead to the wrong failure mechanism being analysed and/or a conservative Factor of Safety (FOS), or Strength Reduction Factor (SRF), being calculated, leading to a false sense of stability. There exists a paradigm that the FOS calculated using 2D limit equilibrium (LE), or the Strength Reduction Factor (SRF) calculated using 2D finite element (FE), modelling methods is generally conservative, ie lower, than the true FOS. However, this assumption that 3D FOS, or 3D SRF, is always higher than 2D FOS, or 2D SRF, is not always correct (Chen and Chameau, 1983; Bromhead and Martin, 2004; Herza et al, 2017; Pyke, 2017; Dana et al, 2018).

Nov 29, 2022

By Enrique Albarrán, Julian Hernández

"In 1942 The “Presa Mixcoac” dam was built, along with 15 other dams, to control the rain fall waterin the mountains west of Mexico City. Mexico City’s population at that time was around 1.5 millionpeople, and the dam was way out of the city."

Jan 1, 2016

By Stephen E. Stewart

This document presents the explosion-proof enclosures used severity of certification tests solutions to linear transient thermal and stress analyses of in underground mines. The results were used to assess the for enclosure windows relative to possible loads occurring in the actual mine environment. Cast iron electric light enclosures with polycarbonate and glass windows were analyzed under steady state thermal conditions (light burning) and for thermal shocks corresponding to an internal explosion (ignition of volatile mine gas) or external quenching (mine water spray system). Thermal shocks to the enclosure, caused by ignited gases or water spray, were applied via a series of load steps in the transient analysis. The temperature dependence of material I properties and of the film heat transfer coefficients were included in the model. The work demonstrates that thermally induced stresses are strongly influenced by the way the window is mounted in the enclosure. It also shows that the MSHA Thermal Shock Test, if performed on an unsupported lens (or window), produces lower stresses than the lens (or window) may experience in the mine environment.

Jan 1, 1984

The typical reactions which the reductants undergo during ferroalloy production are reviewed, and identified as reaction with CO2 and with SiO, and dissolution in metal. Available reactivity tests for these three reactions are reviewed. It is proposed that it is worthwhile considering dissolution kinetics as a reactivity parameter. Greater crystallinity of the reductant decreases CO2 and SiO reactivity, but increases dissolution rates.

Jan 1, 2002

By Cem Altuntas

This paper is the second in a series of two describing the design and construction of a foundation for a major high-rise real estate development on the west side of Manhattan, N.Y. The foundation members consist of large-diameter rock-socketed caissons, driven closed-end steel pipe piles bearing on rock, and a secant-pile retaining wall surrounding the entire site. This paper focuses on the Osterberg cell (O-Cell) load test completed for determining the allowable side-shear resistance between the concrete and the sides of the rock socket. Different qualities of mica schist bedrock, demonstrated by the penetration of rock with the soil auger or drill casing, were encountered. Accordingly, an additional subsurface investigation consisting of test borings at each caisson location was completed. Unconfined compressive strength tests were performed on representative rock samples. The ?soft? mica schist was observed to have vertical foliations and high mica content. For the first time in Manhattan, an O-Cell load test was performed to determine the allowable side shear resistance for both the soft and hard mica schist bedrock. The side shear resistance obtained from the O-Cell load test is compared with the side shear resistance allowed by the New York City Building Code and empirical correlations using unconfined compressive strength values for rock. The rock socket design for the caissons was refined based on the O-Cell load test results.

Jan 1, 2008

By Shuoshi Lu

The Cu-Co ore studied here belongs to the oxide type. The oxidation rates of copper and cobalt are69.30% and 78.78%, respectively. The content of Cu in ROM is 1.34% and that of Co is 0.096%. The ore contains 4.64% carbon.Based on the process mineralogy and previous metallurgy tests, the principalprocess flow-sheet of ?grinding fines 80% -0.074mm, sulphide flotation followed by oxide flotation, and flash flotation for oxides? has been determined.The handling of carbon is determined through tests. The depressant PNL-1 depressed carbon effectively, improved the recovery of sulphide minerals and reduced the reagents consumption.The operation of the flow-sheet was also changed to better at the same time. Keywords: Cu-Co oxide ore, process mineralogy, carbon depression, efficient depressant of carbon

Sep 1, 2012

By Chantale Doucet, Yves Lizotte, Alan Cameron

A joint Federal Government-Industry research project on the effect of geology on the fragmentation of rock excavated by blasting in underground developments was conducted at the CANMET Experimental Mine, near Val d’Or, Quebec. A total of thirteen (13) blasts were studied from November 1994 to February 1995. The analysis of each blast was divided into three stages: pre-blast characterization, including structural mapping, assessment of Rock Mass Ratings (RMR), Tunneling Quality Indices (Q), blast design documentation; blast characterization comprising blast vibration monitoring and analysis; and post-blast assessment comprising fragmentation assessment by digital photoanalysis, calculation of half cast factors and measurements of bootlegs.

Jan 1, 1996

The rapid growth of world civilisation will have a significant impact on the way humans live in the future. As the global population increases and more countries demand a higher standard of living, the world must provide more food and greater energy and mineral resources to sustain this growth. The difficulty of doing this is compounded by three broad trends: the conversion of agricultural land to development uses; the increasing urbanisation of the world's population; and growing concern for the maintenance and improvement of the environment, especially regarding global warming and the impact of population growth. Underground space utilisation offers opportunities for helping address these trends.

Jan 1, 1993

By Y. M. Jiang

Longwall faces can move at high advancing rates, but many geological variations can cause unexpected instabilities and production losses. The rapid movement makes it necessary to evaluate different geologic conditions in the rock mass as fast as possible to assess their effects on the longwall face and shields. It is believed that prompt awareness of geologic conditions is the key to preventing instability at a longwall face. This paper introduces the application of fuzzy set theory for characterizing and evaluating roof conditions. Real-time monitored data coupled with fuzzy set analysis provides valuable information, such as shield leg pressure, developing load on shields, intervals of periodic weighting and the ratio of developing loads during periodic to normal times.

Jan 1, 1997

By Dean Workman

Located in downtown New York City, this project necessitated an innovative conveyor design for successful muck removal. This paper will discuss the technical challenges and engineering solutions of the muck transport system which consists of every commonly recognized version of a belt conveyor. The elaborate system includes a TBM conveyor integral to the back-up system, a wall-mounted extensible conveyor, a crown-mounted transfer conveyor, a floor-mounted fixed-length conveyor, a pocket-belt vertical conveyor, three cascading overland conveyors, and one radial stacker. The most challenging design element was an over-land conveyor featuring a box truss for muck transportation over Northern Boulevard while simultaneously going under the Queens Plaza railroad viaduct. An overview of the project is provided along with the following topics: developing final plans from the proposal concept, interfacing with existing works, communication with the joint venture, and complying with local regulations.

Jan 1, 2008

By Feria Bengoa

El creciente interés del público sobre los problemas ambientales, la satisfacción de los clientes y la seguridad minera, ha generado un alza de leyes en el sector minero e industrial, nuevas ONG y la búsqueda de productos, materiales y procesos compatibles con la preservación de los recursos naturales y cada vez más seguros. En ese sentido, el presente trabajo muestra la estructura del SIG basada en el ciclo conocido de Shewhart (PDCA), y que constituye la espiral de mejora continua de las normas internacionales ISO 9001, ISO 14001 y OHSAS 18001. La base comprende 17 procesos que conforman el SIG según la filosofía del PDCA, los que han sido agrupados como: Política, Planificación, Implementación, Evaluación, Mejora y Revisión de la Alta Dirección. La implementación del SIG que se está realizando en la Fundición de Cobre, asegura la calidad del proceso productivo, estandarizar las mejores prácticas operativas a través de instrucciones de trabajo y procedimientos, motiva y forma a todo el personal de la empresa, cumple con la legislación y mejora la seguridad y salud ocupacional de todo el personal.

Sep 12, 2005

By Arsenio Enriquez, Adrian Deneys

"Rio Tinto through its subsidiary Kennecott Utah Copper Corporation (KUC) and Praxair have implemented the CoJet® gas injection system for copper anode refining. The system provides the capability to melt on average 60 to 70 tons of scrap copper per heat (with acceptable NOx emissions). The system has demonstrated the potential for tuyere-less sulfur and oxygen removal using coherent jet technology.This paper describes the process concept, system development, laboratory testing, implementation, current operation and ongoing developments."

Jan 1, 2009

By S. A. Kenzap

Risk & Uncertainty ? Uncertainty about a situation can often indicate risk, which is the possibility of loss, damage, or any other undesirable event. Most people desire low risk, which would translate to a high probability of success, profit, or some form of gain. Risk = Likelihood x Consequence Risk is the possibility of loss, damage, or any other undesirable event.

Oct 1, 2010

By Luther W. Bahney

Jan 1, 1912

By M. N. Nabighian, J. R. Odekirk, D. M. Hausen

Preliminary investigations based on the concept of cross-power indicate that quantitative volume percentages of minerals, including quartz, orthoclase, plagioclase, fluorite, and chalcopyrite can be obtained by X-ray diffraction analysis. Pulverized samples are scanned from 4° to 65°, 2e, using a Norelco diffractometer, with the output recorded on a punched tape at 40 intervals per degree, 29. Errors from crystal orientation are minimized by (1) gridded surface packing, (2) sample spinning, and (3) quantitative measurement of all major diffraction peaks. Computer programming enables rapid quantitative evaluation of X-ray diffraction data. Results to date indicate that most minerals analyses can be performed within an accuracy of ±2%. Metallurgical applications include analysis of various flotation concentrates and tailings.

Jan 1, 1973

By Paul D. Merica

Jan 1, 1937

By E. Dervaric

The main purpose of this paper is to introduce the main strategic restructuring aspects of companies that are directly (coalmines) or indirectly (companies that depend on coalmines) linked to coalmining. An attempt is also made to determine the principal factors required for the successful execution of a restructuring process in companies focused on the basic activities of coalmining, such as companies that provide supporting activities. The restructuring process exerts an influence on the whole area that relies on coalmining. So coordination of activities among the government, the local community, and the coalmine is very important. This is the major premise of this paper. The first section of the paper focuses on identifying and analysing the key factors in restructuring and a selection of key methods, drawing on past and present practice. The key factors to be considered in a model of enterprise restructuring in the coalmining sector are considered. The second section is dedicated to the actual design of the model of enterprise restructuring in the coal industry. The proposed model is based on positive experiences in the restructuring of coalmining companies in Europe, with an emphasis on Slovenia, successful approaches to crisis management in corporations, and identifying key areas in bringing about a strategic turnarounds in company operation. To support the argument for the key business areas, a brief summary of empiric findings has been included to demonstrate the applicability of the proposed model and the restructuring process. The summary is based on the survey done in both Slovenian coalmining companies (especially in Velenje Coal Mine) and their subsidiaries. The conclusion integrates key findings and outlines issues for further consideration and discussion. Keywords: restructuring, coalmining, Velenje Coal Mine, strategic factors, restructuring model.

Jan 1, 2008