Search Documents

By Muhammad Abid, Kh. .. S. Karimov

"In this study, design and investigation of biogas digester consisting of methane tank with built-in solar collector to utilize solar energy for the heating of the slurry prepared from the dung and heat exchanger is designed, developed and tested. The digester was laboratory type and consists of cylindrical metallic tank of size of 0.5 m in diameter; 1 m in height and 200 liters in volume. The surface of the digester from outside was covered by thermo insulated material a glass wool, except of south side (in northern hemisphere). This side played the role of built-in collector and was blackened to increase absorption of solar irradiation and covered under 45o by glass. In the blackened side of the digester on the different heights it was installed metallic pipes for the inlet and outlet of the air, connected with heat exchanger installed inside of the digester. The heat exchanger was fixed in the level above of the inlet pipe. The horizontal plane reflector concentrates solar beams to blackened side of the digester. In the winter period, it was found that the retention time of this digester is shorter on 15% and produced biogas volume is larger on 20% with respect of ordinary biogas digester. This digester is used for the demonstrative purposes and as a teaching aid presently and base on the results it may be used for the construction of large volume digesters for use in the farms, especially located in the remote and mountain areas where the climate in the winter period is cold. Introduction At present many experts around the world have focused their efforts to energy crises because energy is one of the most important factors for the development of the society. It is known that consuming energy is proportional to quality or standard of life. There is a close relationship between energy consumption and the Gross National Product (GNP). It is obvious that for further development of the country additional sources of energy is required, which are cheap, safe and environmentally compatible with respect to the action on possible wastes. Utilization of renewable energy is one route to help in solving the above mentioned problems. In particular, biogas as a source of renewable energy is produced by biotechnology and used wide on residential scale [1]. The biogas was produced for the very first time in 1814 by Deivy from organic wastes. In 1900 production of biogas was started in Bombay (India) [2, 3]. Biogas consists of 55-70% methane (CH4) and around of 27-44% carbon dioxide (CO2) and less than 1% H2 and H2S. At present biogas is used widely in some countries for lighting, machines, and vehicles, generators, cooking and heating. Biogas generation is suitable for small to large scale operation and at present is realized in a number of developed and developing countries as USA, Hungary, China, India etc. Since 1990s biogas projects construction in China has developed steadily by the end of 1998, there were altogether 6.88 million household biogas digesters [4]. In Russia biogas digesters are used for processing of hard dung into biogas [5]. Over the last few years the very first biogas digesters were constructed in Tajikistan as well [6,7] and it was found that the digesters can work with sufficiently high efficiency in mountain areas as well ."

Jan 1, 2008

By W. J. Schuster

*Original Pages Missing From Book HANNA COAL CO., Division of Pittsburgh Consolidation Coal Co., operates three large under- ground mines in eastern Ohio. The section of Pitts- burgh No. 8 coal seam in which these mines are located varies in thickness from 52 to 64 in. It is immediately overlain by a stratum of shaly material 12 to 15 in. thick locally known as draw slate, which is structurally very weak and which disintegrates rapidly upon exposure to atmosphere. Immediately above the draw slate as it is normally found is a band of extremely high ash material 6 to 12 in. thick known as roof coal or rooster coal, and above this is a stratum of conglomerate material varying from 4 to 10 ft in depth. Overlying the conglomerate is' a relatively thick stratum of limestone, the first stable material above the Pittsburgh coal seam in eastern Ohio. With the method of full-seam mining that has been adopted, draw slate is shot down, loaded with the coal, and removed in the preparation plants. The roof coal then becomes the permanent roof. The major problem in mining the No. 8 seam in eastern Ohio is control of the roof. Since the strata above the draw slate contains no material with a structure firm enough to provide self-support, the roof begins to sag in a relatively short time after the coal and draw slate have been removed. The problem thus becomes one of getting temporary safety posts under this roof as quickly as possible to prevent a break or separation from occurring either in the roof coal or in the conglomerate above it.

Jan 5, 1954

Exploration and mining title administration in the Northern Territory has changed dramatically over the last 20 years. These changes have occurred due to legislative amendments, technological developments, and the changing face of the mining industry. The first legislation to control mining in the Northern Territory was the Northern Territory Gold Mining Act (1873) of South Australia. In 1911, control of the Northern Territory was passed from South Australia to the Commonwealth. As a result of the mining boom which followed the discovery of gold in Tennant Creek in 1932, the Commonwealth passed the Mining Ordinance of 1939. This legislation was amended 39 times and stayed in force until July 1982, when the self-governing Northern Territory passed the Mining Act 1980. This Act is still in force and is continuously under review. The first computerised mining titles system, REGIS, was created in 1984/85 and was, to all intents and purposes, just a computerised index. Various modifications ensued, and in 1989 the Titles Database was unveiled. The database has developed to be one of the most sophisticated yet user-friendly mining titles databases in Australia. In excess of 50 companies have access to the database from their own offices. Work continues on its development and fine-tuning. The paper outlines the development of the database since inception.

Jan 1, 1994

By William C. Larson

The number of uranium in situ leach operations has increased significantly since 1975. As of May, 1980, there were a total of 27 active projects, including 16 commercial scale operations (or under construction) and 11 pilot scale operations. The south Texas uranium district and Wyoming have been the most prominent areas in early field experiments as well as in commercial application of this new recovery technique, although in situ leach tests are now being conducted in Colorado and New Mexico. The growing number of commercial-scale operations is accepted as prima facie evidence that in situ mining now offers a third option along with open pit and underground mining for winning uranium from sandstone host rocks. It is estimated that in 1979 about 9 percent of the nation's total uranium production was from in situ mining. However in situ mining of uranium is not without its environmental controls. The primary emphasis of environmental controls falls into two catagories; namely, control of the leach solutions during mining and demonstration of ground water restoration. Finally this paper briefly reviews the Bureau of Mines research program in uranium in situ mining.

Jan 1, 1980

By Chunlin Chen

Published data on thermodynamics of tin in liquid copper, matte and slag have been reviewed, assessed and used in development of thermodynamic solution models of melts. The developed model/database was applied in modelling the Sn deportment in primary copper smelting and e-waste melting processes. The results show that Sn can be removed from the matte through evaporation of various volatile Sn species (with SnS the most volatile) and slagging during copper smelting. The Sn removal increased with increasing matte grade due to the increased gas and slag volume. In the e-waste smelting process, fluxing strategy was developed for smelting e waste to produce a slag with reasonable liquidus and viscosity. Modelling results show that very low amounts of Sn reported to the gas phase due to low S, hence low SnS partial pressure in the system. The black copper produced could contain a few percent of Sn depending on the oxygen potential. The Sn in the black copper could be removed to the slag phase during anode refining. INTRODUCTION Tin is an impurity element commonly found in copper ores, which will be dispersed into various solid, liquid, and gaseous streams during the pyrometallurgical processing of copper. Tin alloy is widely used in electronic soldering due to its low melting point. The growth in treatment of recycled e-waste through primary and secondary copper smelting has led to an increased tin input to the smelting system. Therefore, the deportment of tin between phases is of great interest to the operators of modern smelters. Multi-Phase Equilibrium (MPE) is a thermodynamic package developed by CSIRO for simulating reactions between phases in multi-component and multi-phase systems (Zhang et al., 2002). Over the years the capability of the MPE model has been extended to cover the behavior of a large number of elements in high temperature system (Chen, Zhang, Wright, & Jahanshahi, 2006). In the present paper, the thermodynamic data on tin in liquid copper, matte and slag have been reviewed, assessed and used in the development of a database for Sn slag, alloy and matte phases. The model/database was applied in modelling the tin deportment in primary copper smelting and e-waste smelting processes. The aim of this study is to provide a better understanding of the chemical behaviours of tin in high-temperature copper processing and e-waste smelting.

Jan 1, 2019

By E. F. Divers

In response to a request from the Mine Safety and Health Administration, the Bureau of Mines has recently completed a respirable dust survey of 18 U.S. coal preparation plants. Of these, three were essentially free of dust problems. Respirable dust exposure of workers in the remaining plants depended on the time spent in the dusty areas. In five of the plants surveyed, Bureau tests showed that in some areas worker exposures could exceed Federal dust limits in less than 2 hours.

Jan 1, 1988

By A. Ignatieff

"THE WORLD'S coal resources represent the largest component of non-renewable energy resources. Coal is now regaining Its position following a temporary decline, particularly in North America during a period of about a quarter of a century. This period provided the opportunity to improve both surface and underground mechanization, thereby increasing the productivity and improving conditions for humans in the mines. Similarly, in preparation, improved cleaning of coal from various impurities including sulphur was achieved, to meet the more demanding requirements for coking coal. Progress was also made in combustion, particularly related to the reduction of pollution. Canada participated in most of these developments, despite the country's strong commitment of the use of hydrocarbons during this period. _Bearing in mind the vastness of this land (3.85 million sq. miles) by comparison with countries like U.S.A., U.S.S.R., and China, Canada's coal resources estimated to date are not large and they are scattered. The original evaluation of 1913 estimated the ""reserves"" from seams over one foot in thickness and a limiting depth of 4,000 ft at 1.2 trillion metric tons. D:. ~.R. MacKay, in his evaluation for the 1946 Royal Commission on the coal industry, known as the Carroll Commission, reduced the ""reserves"" to 99 billion short tons. The increased knowledge now available would indicate that the 1913 estimated was too liberal and the 1946 estimate too conservative but both were closer to a resource than to a reserve designation. Some adjustments of Dr. MacKay's estimates were made in 1970 by B.A. Latour of the Geological Survey of Canada and L.P. Chrismas of Energy, Mines and Resources Canada (EMR). In the last decade the Alberta Energy Resources Conservation Board has developed its own methods of evaluating coal resources and reserves. A methodical approach of exploration and evaluation was carried out by Saskatchewan jointly with the federal government of the lignite resources of Southern Saskatchewan. A similar joint program is in progress in Nova Scotia. Meanwhile, the industry itself carried on an extensive exploration program on the outcrops of promising projects in the Inner Foothills belt of Alberta and British Columbia in preparation for surface mining on a very large scale, with some development of hydraulic mines. All these activities have been reflected in the increase of the country's resources and reserves, which now fortunately are separately defined. In 1979 EMR issued Report E.R. 79/9(1>; the data were developed in 1978 and provided to the World Energy Conference Organization<2>. In 1980 the World Coal Study (Wocol), an international group that included Canada carried out a study which updated the W.E.C. data, indicating some reduction of the 1978 figures; quantities were reported in million metric tons of coal equivalent (C.E.)*(Jl."

Jan 1, 1985

By Franklin Bache

There seems to be in the public mind, and even in the minds of some coal-operators not experienced in mines subject to dust-explosions, a feeling that there has been somet-hing mysterious at the bottom of a number of recent American colliery-exploaions. It has been declared in cases of accidents in mines regarded as particularly well equipped, in which every preventive precaution was said to have been taken, that the explosions were incomprehensible, and resulted from causes beyond the present knowledge of the practical coal-operator. But it is safe to say that no explosion has taken place which could not be explained by reasons well understood by most operators. The U. S. Geological Survey Testing Laboratory, recently inaugurated at Pittsburg for the reported purpose of investigating scientifically the matter of explosions in mines, will discover no new explanation of explosions. It can, however, co-ordinate the previous investigations of similar boards in England and on the Continent; and it may do a vast amount of good by promulgating widely, and in a form comprehensible to the most unlettered miner, certain facts and obvious deductions that cannot but have an effect in reducing the number and extent of the mine-disasters which, in the last few years, have been so terrible in frequency and magnitude.

Jan 1, 1910

By F. M. Clement

British Columbia, unlike the Prairie Provinces, cannot lay claim to vast prairies. She can, however, claim many valleys, uplands and plateaus that are capable of marked agricultural development. It has been said that British Columbia is not an agricultural province. This may or may not be true, but at the present time agricultural production in this province stands second only to that of forestry. The industry has advanced from a total production of 8 millions in 1908 to a total production of 60 millions in 1924, a total increase of approximately 650 per cent in 16 years. In the last 10 years production has increased from 30 millions to 60 millions. No other industry can point to such a rapid development. In 1908 British Columbia imported 12 million dollars worth of foods compared to the 8 millions which were produced at home. In 1924 she imported 20 million dollars worth of foods compared to the 60 millions worth produced at home. In addition we exported foods to the value of approximately 10 million dollars. British Columbia is therefore self-sufficing in-so-far as values ar.e concerned except for approximately 10 millions of dollars. It is not to be expected that this province will ever grow all the coarse grains that she may require: these, along with certain meats, will always be a heavy item in the imports. We are concerned at the present time more with the value of the products than with the quantities produced: in other words, with quantities only in-so-far as ? quantities improve value.

Jan 1, 1925

By G. Sachs, G. Espey

IT is well known that high residual stresses are created in tubing by the sinking process, in which no internal tool or mandrel is used.1-4 In this process, the wall thickness is usually slightly increased.4,5 In tube drawing with a plug, the residual stresses are gradually reduced with increasing reduction of wall, and, by the conventional approximation methods of stress measurement, no stress is detected in tubing in which the wall reduction is over 50 per cent of the total reduction in cross-sectional area.1-6, It has also been observed that higher stresses are set up by the use of wide-angle dies than by the use of acute dies.2 The actual stress distribution in drawn .tubing has been investigated by a few workers,7-9 but has not been related to the conditions of the drawing process: Some attempts have been made to correlate accelerated cracking tests for stresses in brass products with the magnitude of the circumferential stresses and the condition of the metal.1-10 MATERIALS AND PREPARATION The material used in this experiment was commercial cartridge-brass (70 per cent Cu, 30 per cent Zn) tubing in the straightened and annealed condition.‡ This tubing was of various outside diameters and had a wall thickness of 0.032 in. It was sunk to 1/2-in. outside diameter by means of an experimental 10,000-lb. hydraulic draw-bench, with a maximum drawing speed of 8 ft. per minute. All dies were of 1/2 -in. diameter. Various die materials and contours were used in order to study the effect of die design on residual stresses in the tubing; the specifications for the dies are given in Fig. I. Castor oil was used throughout as lubricant. Chattering occurred in sinking some of the tubing, particularly when dies having the more acute angles were used, but the tubes showing chatter marks did not differ markedly from those with a smooth surface regarding the magnitude of residual stress. The source of the chattering has not yet been revealed. The wall of the tubing becomes thicker during sinking, as previously observed 4,5 The increases in wall thickness were 3, 7 and 9.5 per cent on the average for 6, 20 and 33 per cent reductions in diameter, no effect of the contour being noticeable. The reductions mentioned throughout this investigation do not consider this fact, but are reductions of the outside diameter. For the evaluation of the residual stress two fundamentally different methods were used. The approximation method1,11 of splitting a certain length of tubing was employed to obtain a bird&apos;s-eye view of the effect of various drawing conditions on the circumferential stress measured by the diameter change occurring on splitting. For the determination of the complete stress

Jan 1, 1941

By John T. Ryan

DEFINITE improvement in its accident fatality rate in the coal-mining industry was recorded during 1941, based on preliminary figures for the period from January through October. Total production during this ten-month period was approximately 91 percent of the total production in all of 1940. The ten-month accident rate for both bituminous and anthracite mining in 1941 was 2.15 killed per million tons of coal mined, compared with a rate of 2.66 for the full year of 1940. The bituminous rate decreased from 2.55 in 1940 to 1.99 in ten months of 1941, and the anthracite rate from 3.62 to 3.53 in similar periods. The decrease is more apparent for the bituminous branch of the industry, as the high figure in 1940 was due to seven major disasters which brought death to 276 men. The same number of major explosions during ten months of 1941 caused only 64 lives to be lost. The severity of the explosions has been lower this year but a definite need still exists for reduction in this type of accident.

Jan 1, 1942

By Edward Keller

THE present ruling principle in shop and factory, induced by conditions of. keen competition, is to do the greatest amount of work in the shortest time, or in other words, to secure the greatest output at least cost, a condition which generally necessitated the substitution of machinery for manual labor. The chemical laboratory in our industrial establishments has remained a factor of minor importance, and, for this, reason, not only has progress been permitted to lag, but the methods of analytical work have been carried on along individual traditional lines. Some works-laboratories are equipped with such conveniences as Gooch filters, suction-pumps, compressed air, shaking-machines, centrifugal machines, crushers, etc., yet there is much room for improvement, particularly in laboratories of metal smelting and refining plants, in which long series of filtrations and stirrings are performed singly by hand in a slow and laborious manner. There are also many other instances in which collective handling appears rational. As a rule the chemist wastes much time by such manual labor, which, in a modern establishment and under up-to-date management, could be more advantageously applied to useful chemical work; and such higher chemical work is gradually and surely becoming recognized as an essential extension of old-time methods of assaying. While it maybe said that in some laboratories, boys and not chemists do the manual labor, it should be borne in mind that all chemical work requires care and accuracy and in these respects boys are naturally a source of concern to the responsible chemist. Moreover, the cheapness of child-labor is largely offset by the increase in the expense-account of laboratory materials, caused chiefly by breakages resulting from care¬lessness. Having; been authorized by the Anaconda Copper Mining

Mar 1, 1905

By F. Lambert

"Amok Ltd./Cluff Mining operates a uranium mine at Cluff Lake in northern Saskatchewan. The project consists of one open pit and one underground mining operation along with a full-scale milling installation.The underground stoping operations are of the narrow vein type and are done between two levels 50 m apart. The mining method is undercut with concrete backfilling. Cuts are 3.5 m in height and can be as narrow as 1.4 m in width.Stoping operations are mechanized utilizing a CT-500E electric Microscoop marketed in Canada by Teledyne. The machine is only 85 cm in width and does all the mucking in stopes. Ore passes are provided in stope roughly every 40 m to 50 m.This paper describes the utilization of the CT-500E Microscoop in the company&apos;s underground operations and provides performance data related to the experience.IntroductionThe Amok Ltd ./Cluff Mining operation is located in the northwestern corner of Saskatchewan. The project started in 1980 with open pit mining and milling operations. In 1983, an underground mining operation began production . Today, the Amok Ltd./Cluff Mining installation produces 800 tonnes of uranium per year , which originates from both the open pit and the underground mine at about the same proportion."

Jan 1, 1990

In March 1956 a conference on geochemical methods of prospecting for ore deposits was held in Moscow. This conference was the culmination of a ten-year period of extremely rapid increase in both research and routine application of geochemical prospecting methods in the USSR. This activity was divided among groups centered in extremely widely separated bases of operation, ranging from Moscow and Leningrad in the West, Yerevan in the Caucasus, and Alma-Ata in Central Asia to Chita near the Manchurian frontier in the Far-East. The All-Union Conference on Geochemical Methods of Prospecting for Ore Deposits, as the meeting was called, was the first opportunity for these scientists from many parts of the country to meet and exchange experiences. It also served to introduce members of the different research laboratories located in the city of Moscow itself, where adequate channels of technical communication had not yet been established. As a result of the Conference, it was resolved that a concerted effort should be made for the participants to publish the results of their work. Two books have appeared as a direct response to this resolution. I. I. Ginzburg prepared a synthesis of the field of geochemical prospecting for minerals based on the material presented at the Conference. This volume has been translated into English and is now available. In addition, the individual papers presented at the Conference were assembled into a symposium volume and published in 1957 under the editorship of V. I. Krasnikov. Unless otherwise noted, these two books have supplied the source material for the present appraisal of the status of geochemical prospecting in the USSR. It is thus about four to five years old. In the years following the conference, the literature has carried a substantial volume of technical papers, together with a few monographs pertaining to specialized aspects of geochemical prospecting.

Jan 6, 1960

By Zhong Juya, Wang Yong, Guo Xueyi, Song Yu, Tian qinghua

"In this work, the flow of zinc in China, 2004, was traced within the STAF model, and the situation of production, consumption and recycling of zinc resources in China were introduced. The SFA is performed on zinc flows during its one year life cycle in detail. The result reveals that China produces and utilizes a large amount of zinc, while the efficiency of renewable zinc resources is still relatively lower. As one of the biggest producer and consumer of zinc in the world, China is facing a severe depletion of zinc resources. How to increase the resource efficiency is a significant issue for zinc industry of China. Based on the result, several advices were proposed in the paper, aiming to contribute important reference information for the industrial metabolism and resource management and recycling of zinc industry in China. IntroductionZinc is one of the important metals in national economic development in China; it has good conductivity and corrosion resistance, with high scalability when heated to 100 ~105_. Zinc is mainly used for galvanized zinc industry, as the coating of steel and various parts, and it has also been applied to the manufacture of brass, bronze and corrosion-resistant alloys, which are widely used in machinery manufacturing, printing, national defense and so on. In addition, zinc compounds are utilized in various fields, for example, ZnO is used for infiltration wood, paper, rubber, paints, etc.; ZnSO4 for leather, ceramics, textiles, medicine, etc.; ZnCl2 for infiltration wood; ZnS2O4 and Zn (HSO2 • CH2O) 2 for the paper and textile bleaching, etc. [1]. The extensive use and consumption of zinc in industrial production and social life promot the rapid development of zinc industry, which made zinc the third largest non-ferrous metals in the world."

Jan 1, 2008

By Charles Brush

THE general subject of accurate pyrometry, its great development in recent years, and the importance of its application in arts and manufactures is so ably treated in other papers that this paper will bee confined to a resume of some research work on certain temperature effects in carbon and other steels, some of which appear to, be new. The results of these researches are embodied in several papers presented to&apos; various scientific societies during the last few years, most of them under the general title of Spontaneous Generation of Heat in Recently Hardened Steel.1 Several years ago, when studying the behavior, tinder certain conditions, of specimens of hardened tool steel, I observed that they all spontaneously generated a small quantity of heat, the rate of generation diminishing from day to day for several weeks before generation became imperceptible in the sensitive calorimeter used. In each case the steel had been hardened only a few days prior to its use. It seemed highly probable that the generation of heat was associated with some sort of "seasoning" or incipient annealing process, perhaps accompanied by slight changes of volume, and that it would be most rapid immediately after hardening. I subsequently investigated this curious phenomenon more fully. Twelve ½ in. round bars of tool steel, 5 in. long and with machined surfaces, were hardened by heating to high cherry red in a reducing atmosphere of a gas furnace and quenched in cold water. The bars then had a thin strongly adhering coating of black oxide. They were next stirred in a large quantity of water at room temperature, to acquire that temperature, wiped dry, and oiled with heavy, neutral mineral oil to prevent generation of heat by further surface oxidation, wiped free of excess of oil and placed in the copper cylinder of a heat-insulated box.

Jan 9, 1919

By Jose M. Sobral

Approximate figures for petroleum production in Argentina for 1929 show an increase of only about 300,000 bbl. over production for 1928. This increase is due to greater yield in the Plaza Huincul and in the Salta regions. Table 1 shows the distribution of production in the various fields of the whole country, using estimates for the later months of the year. The outlook for production remains about the same as in 1928. It is believed that in northern Argentina there are regions that contain oil, but they are yet unexplored. Notable traces of oil at depths between 1280 and 1390 m. have appeared in a 1500-m. boring in Comodoro Rivadavia, but their importance is unknown.

Jan 1, 1930

By Ancel St. John

AT THE New York meeting of the Institute of Metals Division in February, 1927, Jeffries and Tarasov presented a paper on Tungsten and Thoria,1 in which the experimental facts were interpreted in accordance with the prevailing point of view that the thorium is present as the oxide, thoria. In discussing that paper the writer of this article stated that his own investigations, which had been unavailable to Messrs. Jeffries and Tarasov, showed that the so-called "thoriated" tungsten filament failed to disclose any sign of the oxide when subjected to X-ray diffraction analysis, but did give plenty of evidence of the presence of metallic thorium and, in certain cases, of a material believed to be an alloy of tungsten in thorium. Since these results were completely at variance with the results reported in the paper under discussion and with other papers which had preceded it from time to time in the past, it was felt that further discussion should be withheld until the new evidence could be presented adequately. Arrangements were therefore made to present that evidence at this meeting. MATERIAL EXAMINED The material examined was high-emission filament such as is used in radio tubes, supposed to contain about 0.75 per cent. thoria. The actual analysis was not stated. SCOPE OF THE INVESTIGATION The investigation was undertaken because of a feeling that the thorium present in filamentary material of this type exists as metallic thorium or as an alloy of thorium and tungsten and not as the oxide. Attention was therefore directed to determining: 1. The minimum amount of thoria detectible in a mechanical mixture of thoria powder and finely divided tungsten. 2. The amount of thoria detectible in the filament. 3. The condition of any thorium present in other form than as thoria. 4. The amount of thorium dissolved in the tungsten.

Jan 1, 1928

By Darwin Soler

This chapter will outline the operating procedures at Freeport Kaolin Co.5 kaolin mining operations in Georgia, with emphasis on explaining new techniques recently introduced to reclaim mined-out areas for reforestation. Kaolin is found in the central Georgia area (See Fig. 1) in lenticular, sedimentary deposits of high purity. The beds are Cretaceous in age and vary from 4 to 60 ft in thickness, under a cover of sedimentary overburden ranging from 5 to 150 ft. The kaolin beds contain the mineral kaolinite (a hydrous aluminum silicate) and have a particle-size distribution ranging from about 20µ to the submicron level and averaging about 60% below 2µ. The only contaminants in the deposits are coarse mica, quartz particles, and minor amounts of iron and titanium oxides. These kaolin deposits vary widely in quality from deposit to deposit and also vary within individual deposits. Some of the controlling quality specifications which are determined during exploration are viscosity in water suspension, optical brightness index as measured by reflectance, amenability to bleaching, and particle-size distribution. For this reason, only a small portion of the total kaolin reserves in the Georgia belt are suitable for wet processing for the present markets being served. Kaolin clays are selectively mined by different mechanical methods and are beneficiated by both wet and dry processing to produce a number of products used as fillers and coatings in the paper industry; fillers or additives in the paint, plastic, and rubber industries; and as basic raw materials for the ceramic industry. The State of Georgia is the largest kaolin producer in the United States, with 3,206,454 tons produced in 1966, according to U.S. Bureau of Mines statistics. Freeport Kaolin Co’s processing plant is located in Gordon, Ga., about 20 miles east of Macon, Ga.

Jan 1, 1969

By J. H. Viljoen, N. B. Strydom, J. S. Greyson, C. H. Van Graan

SYNOPSIS Bad eyesight and poor illumination can contribute to the occurrence of accidents in mines. As one part of a study of this problem, surveys of light intensities have been conducted in 19 gold mines. On 17 of the mines the surveys were on one underground level only, whilst in two of the mines more intensive surveys were conducted by measuring light intensities in all areas to determine any inter-mine variations between the levels of illumination. Readings of light intensity were taken underground at stations, tips, winches, stopes, conveyor belts, waiting places, pump stations, fitters&apos; and boilermakers&apos; workshops, ambulance rooms and in haulages. It is concluded that the average levels of illumination in South African gold mines are comparable with those reported in the literature for mines elsewhere. Standardisation of lighting conditions underground could eliminate inter- and intra-mine variation in illumination levels where they occur. A guide to mine illumination practice would assist such standardisation, and help increase the levels and effectiveness of illumination in mines. Some suggestions are made in this latter connection.