Search Documents

By Donna Guillen, Matthew Lehar, Sebastian Freund, Jennifer Jackson, Helge Klockow

"Research and development is currently underway to design an Organic Rankine Cycle (ORC) system with the evaporator placed directly in the hot exhaust stream produced by a gas turbine (GT). ORCs can be used to generate electricity from heat that would otherwise be wasted, thus producing carbon-free energy. In conventional ORC configurations, an intermediate oil loop is used to separate the hot gas from the flammable working fluid. The goal of this research effort is to improve cycle efficiency and cost by eliminating the pumps, heat exchangers and all other added cost and complexity of the additional heat transfer loop by developing an evaporator that resides in the waste heat stream. Direct evaporation – although simpler and less expensive to implement than indirect evaporation of the working fluid – has historically been avoided due to a number of technical challenges imposed by the limitations of the working fluid. The high temperature of the hot exhaust gas may cause decomposition of the organic working fluid and safety is a major concern due to the high flammability of some of these working fluids. The research team has addressed these challenges and developed a new direct evaporator design that can reduce the ORC system cost by up to 15%, enabling the rapid adoption of ORCs for waste heat recovery. The ORC system is intended to integrate with the GT either as a retrofit or to be marketed as a single package, thus maintaining the manufacturer’s warranty.IntroductionWaste heat from turbines and engines used in industrial applications along with waste heat from industrial processes are exceptionally abundant sources of energy. If even a fraction of this waste heat could be economically converted to useful electricity, it would have a tangible and very positive impact on the economic health, energy consumption, and carbon emissions in the U.S. manufacturing sector. Land-based gas turbines are used in a broad range of applications to produce both shaft and electrical power. Most commonly known for generating electricity either as peaking units or as base load units, they are also used to directly drive pumps, compressors or other machinery requiring shaft power. Simple cycle gas turbines have the advantage of a short startup time relative to coal-fired and nuclear units, however, they incur a significant penalty on their efficiency. Large frame gas turbines usually are combined with bottoming steam-based Rankine cycles to increase the overall efficiency of the system and thereby improve their cost performance. Small-frame gas turbines with exhaust temperatures around 500°C could in principle benefit from steam bottoming cycles, but rarely use them in practice because of the high capital cost of the steam system. Particularly for base load small frame gas turbines, akin to those used in pipeline applications, an increase in efficiency is highly desirable."

Jan 1, 2011

By E. Harrison

The Greens Creek Ore Bodies are located approximately 18 miles southwest of Juneau, Alaska in an area on Admiralty Island classified as a non-wilderness national monument. An area-wide stream sediment geochemistry program targeted the deposit in October of 1973. Today, after 37,000 meters of combined surface and underground diamond drilling, three ore zones are known to exist with total reserves approaching 4.1 million tonnes. Lying within moderately folded metasediments of an undetermined age, these orebodies are thought to be of seafloor exhalite orgin and contain unusual and impressive amounts of gold, silver, lead, zinc and copper.

Jan 1, 1986

CONTENTSThe significance of values givenINTRODUCTIONTHE ORE1. DATA SECURED FROM THE MILLING PLANT AS OPERATING BETWEEN 1938 AND 1942(a) Mill Recoveries(b) Mill Flow Sheet(c) Scheelite-Garnet Association(d) Detailed Examination of Mill Performance during 1942Crushing UnitsCoarse Rolls DischargeFine Rolls DischargeFeed to Huntington MillsFinal Ground ProductProduction of -200-mesh Scheelite SlimeSummary of Information on Crushing and Grinding Circuit(e) Detailed Examination of Mill Performance During 1942Concentrating UnitsLocation and Nature of Scheelite LossesSize Distribution of Scheelite LossesDistributor Spigot ProductsSummary of Information on Concentration Circuit(f) Detailed Examination of Mill Performance During 1942 Gravity Plant Feed2. EXAMINATION OF MINE SAMPLES TAKEN DURING 1942(a) Introduction(b) Nature of the Ore(c) Sampling of Mill Feed(d) Testing Technique(e) Minus 1/8-inch Ores-Naturally Broken Fractions(f) Recoveries from Plus 1/8-inch Fractions-Crushed to Minus 1/8-lnch(g) Probable Recoveries Obtainable from Weathered Ores140 Contour120 Contour90 Contour(h) Examination of an Ore Sample from the 90-foot Adit(i) Run-of-Mine Ore(j) Evidence of Maximum Sizes of Scheelfte Present in Run-of- Mine Ore(k) Summary of Information on Liberation and Recovery from the Ores as Mined in 1942 and from the Mill Samples

Jan 1, 1944

This report, the second in an annual series, summarizes information on latest technological developments and advances, and identifies trends in mining and metallurgy based on a review of activities in the minerals industry in 1971. Exploration and mining data obtained from an annual canvass are presented for 1971 and are compared with similar data obtained over the past decade.

Jan 1, 1973

By D. J. A. Chambers, J. M. Wempen, K. D. Koper, M. K. McCarter, K. L. Pankow

"The EarthScope Transportable Array (TA) of broadband seismometers (www.usarray.org) was deployed across southwest Wyoming from November 2007 through May 2009. During this time period the Array Network Facility (ANF, anf.ucsd.edu) detected and located a total of six seismic events near the trona-mining district. This lack of seismicity is atypical compared to coal mines employing similar mining methods. In this study, eighteen months of continuous seismic data from several nearby TA stations are reexamined using conventional and correlation-based methods to detect seismic events. Waveform cluster analysis and epicentral locations are used to discriminate between mining induced seismicity (MIS) and seismic energy generated from surface blasts at nearby coal mines. The locations and magnitudes of the 143 newly detected MIS events are compared to regional subsidence as measured by Differential Interferometric Synthetic Aperture Radar (DInSAR). INTRODUCTION An abundance of natural resources and a favorable political climate have made southwest Wyoming home to multiple large mining operations. Among these operations are five underground trona mines located approximately 50 km west of Rock Springs, Wyoming. The trona mines employ room and pillar, longwall, and solution mining methods over an area roughly 900 km2, and produce a sizable portion of the world’s soda ash (Brown 1995). Historically, in the Rock Springs mining district, several relatively large magnitude seismic events have occurred. These events are thought to have been related to mining activity and have caused notable subsidence (Case 1997). The largest event in the region recorded by seismometers, ML 5.1, has been confirmed as the 1995 Solvay Trona Mine collapse (Pechmann et al. 1995). In addition, blasting at surface coal mines near Rock Springs produces significant amounts of seismicity; approximately 50% of all daytime seismic events in the Mountain time zone from 2007 to 2009 locate near an active surface mine in this region (Astiz et al. 2014). Much of the current research related to surface subsidence and induced seismicity focuses on wastewater impoundment (Ellsworth 2013) and hydraulic fracturing. The observable seismicity in geological injection environments is widely variable and McGarr (2014) has argued that, in such environments, the maximum amount of seismic energy that can be released is proportional to the injected volumes. Like injection environments, in extraction (mining) environments seismicity is highly variable depending on many geological and operational variables (Boltz et al. 2012; Carnec and Delacourt 2000; Fritschen 2010; Iannacchione et al. 2005; Sen 2013) and does not always correlate well spatially with subsidence, a surface expression of extraction at depth."

Jan 1, 2015

By R Tooher, S J. Oliver

The operation of copper flotation circuit is a challenging task for the site metallurgists and plant operators. To optimise the performance requires meeting both grade and recovery objectives. These plants have numerous pieces of equipment that are monitored by hundreds of sensors. The challenge is to review these sensors and adjust the numerous control inputs to maintain peak operational efficiency for extended periods. There is also a need to respond to equipment failure. These challenges lead to in operational inefficiencies and can result in a reduction in revenue.This paper details an overview of an operational assistance tool implemented at Newcrest's Telfer plant’s copper flotation circuit. This tool is based on a digital twin of the plant. A digital twin is a model of the plant that is simulated in parallel to the normal plant operation. It is fed with the plant data in real time to provide a prediction of plant operation. The model outputs directly generate the metrics that are used to assess the plant performance, and these are compared with the metrics calculated from the actual plant’s operation. Deviations between the model estimate and the plant’s actual performance are used to gather insight into plant health and alert the operator to poor performance. The operators gather more information regarding the root cause by reviewing the model’s inputs that have deviated outside their normal operating range. An evaluation of the plant performance, following the commissioning of the digital twin, showed an overall reduction of acid soluble copper in the tails.This paper discusses the implementation of a digital twin of the plant to monitor plant performance during live operation. It will include details on data collection and cleansing, data reduction techniques, model development, and real-time implementation. The results of the case study of an implementation of a digital twin at Newcrest's Telfer copper flotation plant will be used throughout the paper.CITATION:Oliver, S J and Tooher, R, 2018. Optimising flotation plant operation by using a digital twin in the control room, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 93–100 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By A. Iannacchione

Major Hazard Risk Assessment (MHRA)1 is used to help prevent major hazards, e.g., fire, explosion, wind-blast, outbursts, spontaneous combustion, roof instability and chemical and hazardous substances, etc., from injuring miners. The structured process associated with MHRA helps to characterize the major hazards and evaluate engineering, management and work process factors that impact how a mine mitigates its highest risk. The National Institute for Occupational Safety and Health (NIOSH) studied the application of this technique to US mining conditions through a field-oriented pilot project. Risk assessment teams used in the pilot project were primarily composed of mining company personnel. Ten case studies were performed over a wide cross-section of mines. These mines were representative of the important mining commodities in the US minerals industry, i.e. coal, metal, non-metal, and aggregate. Also, the sizes of the mines ranged from small to large and were located across the country. The ten case studies demonstrate that most US mines have the capability to successfully implement an MHRA and that the MHRA methodology produced additional prevention controls and recovery measures to lessen the risk associated with a select population of major mining hazards. The basic ingredient for a successful MHRA is the desire to become more proactive in dealing with the risks associated with events that can cause multiple fatalities. A successful outcome is marked by a thorough examination of existing prevention controls and recovery measures. When pressed to consider more controls to further mitigate the risk, a well-staffed risk assessment team was able to identify additional controls. For these mining operations, it was important to add additional controls, even if they were not required by existing mining regulations, to lower the risks associated with the major hazards under consideration. If a mining operation is not willing to commit its best people to an MHRA or will not provide them with sufficient time to see the process through to its conclusion, the MHRA output may prove to be useless. Additionally, if a mining operation is not prepared to discuss its major hazards in an open and honest fashion and to present the findings of the risk assessment in a written report, the MHRA output will be unclear, and attempts to monitor or audit important controls may not be possible. A MHRA is most effective when the mining operation possesses 1) a proper understanding of its hazards, 2) experience with informal and basic-formal risk assessment techniques, 3) proper facilities, machinery and equipment, 4) suitable systems and procedures that represent industry Best Practice, 5) appropriate organizational support with adequate staff, communications and training, 6) a formal and thorough plan for emergency response, and 7) a safety risk management approach that is promoted and supported at all levels of the organization.

Jan 1, 2008

COUNCIL OF SECTION DELEGATES Nicholas A D'Arcy, Jr, Chairman (Southern California Section) Charles Chapman, Vice-Chairman (Florida Section) Ben H Parker, Secretary (Colorado Section) Frontier Refining Co Boston Bldg Denver 2, Colorado

Jan 1, 1956

By C. E. More

Some observations on 'ancient' mining at Phalaborwa C. E. MORE. B.A. (Pretoria) (Visitor) A brief account is given of historical references to the Phalaborwa area, the first being to the mountain of copper and iron sought by Francois de Cuiper in 1725. These are followed by a description of several finds in the area, which are related to finds described in the literature and to Bantu tradition on the subject. Phalaborwa is one of the earliest known mining sites in the Republic of South Africa, Loolekop having been a mining centre, as shown by carbon-14 dating, since 770 A.D.

Jan 1, 1974

By N. Careddu

In recent years, slabs with a rough surface have captured a large share of the ornamental stone market. However, the main technologies used for this type of treatment are based on mechanical shock (bush-hammering) or thermal treatment (flaming or flame-finishing). These traditional technologies are widely used, but have many limitations that decrease their usefulness. The purpose of this study was to develop a technology that enhances the natural colors of the rock and produces a rough surface without compromising its mechanical characteristics, in contrast to traditional technologies. This report shows the technical, economic and aesthetic results obtained with a new water-jet treatment and compares it with competing technologies.

Jul 1, 2010

By Staff

"INTRODUCTION Sheet mica is one of the most important minerals in modern industry. It is used in many kinds of electrical devices, and up to the present time no satisfactory substitute for it has been developed. It is necessary for the successful operation of airplanes, ships, motor vehicles radios, and radar equipment. Early in World y r II, the Array and Navy, foreseeing the need for conserving the stock of sheet mica on hand and realizing that imports from India and Brazil were falling off, had strategic mica placed on the critical war-materials list.Examination and exploration by the Bureau of nines indicated that there probably are large undeveloped deposits of mica in Alabama, some of which are near the surface and others at greater depth. The quality of most of this mica is high.During World War I, Alabama mica producers added materially to domestic production, but after 1920 virtually all of the mines closed end miners scattered. During World War II, when imports from India, Madagascar,Brazil,,other foreign sources were reduced, sometime was required for Alabama to act into production. Operators began to produce small quantities in 1942.The Colonial Mica Corporation was created by the Government during 1942 to buy Mica for the Metals Reserve Company, end later Colonial was made sole buying accent for strategic mica. About this time the Bureau of Mines estab¬lished the graphite field laboratory at Ashland, Ala. Samples of mica wore submitted for examination, and advice was requested by property owners and mine operators. This continued during 1943, when as many as 400 visitors a month called at the Bureau's Ashland field laboratory."

Aug 1, 1946

By D. O. Hamiltion

The ISMS program provided for the development and demonstration of equipment modifications in both conventional and continuous coal mining systems. This report describes activities during the demonstration of the conventional equipment and includes machine performance, results of data gathering, system evaluation, and recommendations for implementing improvements.

Jan 1, 1976

By S Sandover, D Glenister

Alcoa World Alumina Australia is committed to sustainability principles as a basis of business success into the future. In March 2001, Alcoa Inc chairman Alain Belda announced a set of far-reaching environmental goals for the corporation, with the challenge that they should be achieved in ways that enhance economic and social performance, while substantially reducing environmental impact. Application of Cleaner Production methods is seen as the key to achieving these joint objectives. In Australia Alcoa has launched a co-ordinated effort to accelerate our application of Cleaner Production principles to delivering cost-effective in-process solutions to environmental issues. Our Western Australian Operations are a signatory to the WA Cleaner Production Statement, through which we provide a Cleaner Production Plan to the State Government on a voluntary basis. This paper describes in general terms AlcoaÆs goals, achievements and directions in applying Cleaner Production to enhance business performance in the economic, environmental and social dimensions. Quantification of the benefits and tracking of progress in quantitative terms is a key challenge for the future

Jan 1, 2002

By L. V. Bell

THE object in prospecting is to find ore. With the exception of certain discoveries of more or less accidental nature, intelligent prospecting as conducted today is, whether consciously or not, based upon a process of elimination. In the following discuss on it is proposed to evaluate those factors that enter into the eliminating of certain tracts of ground and, conyersely, the concentrating of attention upon others. The danger of generalizations as to the barrenness of cer.ain areas, without having due regard for all such factors, is emphasized. The fact that our conception as to what areas or rock formations are to be regarded as favourable or unfavourable is, in some measure at least, changing with new discoveries under diverse and unexpected circumstances, adds more point to the discussion. The criticism might be raised that the subject is treated largely from the standpoint of geology, but that may be met by stating that it is, and must continue to remain, precisely from this standpoint that the prospecror directs his activities. Briefly, the geologist may render the greatest service to the prospector in the early steps of selecting (a) the general territory in which to prospect; (b) the area to be intensively prospected; and, finally, (c) those parts of the claim or claims to be prospected in detail. Although certain phases of the discussion will be, in some measure, of general application, we shall here concern ourselves essentially with prospecting in the pre-Cambrian shield. Furthermore, the subject is so large that it has been decided to limit it to a consideration of that portion of the pre-Cambrian rocks in which is situated the mining district of western Quebec, of which the writer can speak with more personal knowledge. This limitation need not, however, seriously detract from whatever merit the discussion may possess, since the deposits concerned cover a fairly wide range of metallic ores, including gold, copper with associated zinc, and, lastly, molybdenum.

Jan 1, 1936

By W. N. Hoskins

This report covers the final results of a two-phase contract study conducted between July 1974 and October 1976. A comprehensive summary of the initial phase of the study is included. Phase I of the study involved the investigation and evaluation of all potential candidate underground systems for mining the deeper deposits of oil shale and associated minerals in the Piceance Creek basin of northwestern Colorado. Phase II called for the refinement and the detailed technical and economic analysis of the most promising system, or systems, thus disclosed. Of the several systems initially investigated and evaluated, four showed considerable merit for exploiting the deeper deposits: (1) chamber and pillar mining with spent shale backfill, (2) sublevel stoping with spent shale backfill, (3) sublevel stoping with full subsidence, and (4) block caving mining using LHD's. Final refinement and analysis of these four systems indicated their technical feasibility over at least part of the range of conditions expected in the deeper deposits. Their economic feasibility also was indicated under certain operating and market conditions. A variety of engineering, production, and cost information is provided on each of these systems.

Jan 1, 1976

By T. F. Anstett

The Bureau of Mines evaluated the potential availability of chrysotile, amosite, and crocidolite asbestos from 42 properties in market economy countries. This resulted in the development of tonnage-cost relationships indicating the quantity of grades 3 through 7 asbestos at various average total costs of production at 0% and 15% rates of return on invested capital. The availability of grades 2 and 8 was also evaluated, but since each is produced at only one property, no analytical results were given. Total demonstrated recoverable chrysotile fiber potentially available of grades 3 through 7 from the 42 properties evaluated follow: 1.59 million t, 21.00 million t, 16.74 million t, 15.54 million t, and 19.27 million t, respectively. The total amount of crocidolite is 1.69 million t. Owing to the good potential for discovery and development of new deposits, long- term availability of fiber of all three types is not in jeopardy. However, many of the crocidolite properties evaluated in the northern Cape crocidolite field of South Africa have relatively small demonstrated resources, and new deposits will have to be exploited by the late 1990's to sustain projected levels of production.

Jan 1, 1985

By Thomas Leonard Watson

I. HISTORICAL. BARITE has been mined for many years in various parts of Virginia, probably the earliest mining-operations being in Prince William county, within 600 ft. of the Fauquier county line, about 4 miles south of east from Catlett, a station on the Southern Railway. It is claimed that the mineral was mined here as early as 1845. Mining-operations in Campbell and Pittsylvania counties in the Piedmont region, and near Marion in Smyth county, in the southwest Virginia Valley region, were begun about 30 years ago. The mining and milling of barite on a commercial scale in Tazewell and Russell counties are more recent, and commenced about 15 years ago. II. GEOGRAPHICAL AND GEOLOGICAL DISTRIBUTION. Barite occurs in many counties in the State, as shown in Fig. 1, but the industry has been confined to only a few of them. Its occurrence is noted in two of the three major divisions of the State-namely, the Piedmont region east of the Blue Ridge, and the Paleozoic area west of the Blue Ridge. In the Piedmont region the mineral has been mined in the following counties:, Bedford, Campbell, Louisa, Prince William, and Pittsylvania. In the region west of the Blue Ridge, composed of Paleozoic sediments, barite has been mined in Montgomery, Russell, Smyth, and Tazewell counties. Of the counties mentioned, Bedford, Campbell, and Pittsylvania of the Piedmont region, and Russell, Smyth, and Tazewell of the Valley region, have been the principal producers. In 1906, operations were confined to five counties-Bedford, Louisa, Pittsylvania, Russell, and Tazewell-but in the first two counties named there was no production, the work being solely development.

Jan 9, 1907

By Frank B. Fulkerson

Three of the five primary aluminum producers in the Pacific Northwest have facilities in the region to make aluminum mill products. Only one of the three, however, produces a variety of shapes and forms. The principal reason for the lag in development of an aluminum mill products industry was found to be transportation cost. The long range outlook is for expansion, based mainly on growth of the western market for aluminum used in construction, containers and packaging, electrical applications, diesel trucks, mobile homes, and irregation pipe. Consumption of western aluminum mill products in 1985 is projected at 1.1 million tons, compared with estimated consumption of 250,000 tons in 1961.

Jan 1, 1965

By L. D. Snyder, J. K. Russell

"The Lower Jurassic Iron Mask batholith intrudes Upper Triassic Nicola Group volcanic rocks in the Quesnellia terrane of southcentral British Columbia and hosts Cu-Au mineralization. The batholith comprises three mappable intrusive phases, including: Pothook gabbro to diorite, Cherry Creek monzodiorite to monzonite and Sugarloaf diorite. The Iron Mask hybrid forms a fourth mappable unit that makes up to 45% of the areal exposure in the batholith. It is highly variable in texture and composition and subdivided into three types; Type I and II have abundant (partially digested) xenoliths, many of which are derived from the Nicola Group, whereas Type III is xenolith-poor and shows extreme outcrop-scale textural diversity.Pothook and Cherry Creek rocks are similar in texture, mineralogy, whole rock and mineral composition and style of alteration. Contacts between the two can be intrusive or gradational. Rocks collected from these two suites have compositions that are permissive of a single magma batch, although simple crystal fractionation does not explain all chemical variations within and between the two suites. The Sugarloaf unit comprises a diverse group of amphibole-phyric rock types and is texturally and mineralogically distinct from Pothook and Cherry Creek suites.The Iron Mask hybrid represents progressive stages of physical and chemical interaction between Nicola Group country rocks and Pothook magma. Magmatic assimilation (selective or partial) is supparted on the basis of field relationships, petrographic observations, and REB compositional data. Thermal dehydration and partial assimilation of Nicola Group rocks by Pothook magma is shown to be a valid means of promoting early and extensive volatile saturation in the Iron Mask batholith."

Jan 1, 1995

By Keith Harris

The U.S. economy grew moderately in the second quarter of 1985 with real gross national product (GNP) recording a seasonally adjusted annual growth rate of 2.0%, up from the 0.3% growth of the previous quarter but significantly below the 7.1% growth of the second quarter of 1984 (table I). Personal consumption expenditures grew 5.3%, with purchases of durable and nondurable goods rising 7.4% and 5.1 %, respectively; nonresidential and residential fixed investment--the two components of fixed investment--grew 11.8% and 5.6%, respectively; and Government spending rose 3.6%. However, these gains were tempered by a major decline in the growth of business inventories (from $19.1 billion to $8.3 billion) and the continuing growth of the net export deficit (from -$28.4 billion to -$33.3 billion). While the high value of the dollar compared with other currencies has been a major cause of the expanding trade deficit, its value, as measured by the monthly Federal Reserve Board (FRB) multilateral trade-weighted dollar index, has declined over 17 index points from its February peak to 140.94 in July. The July dollar value was still high historically. The rate of inflation, as measured by the fixed-weighted price index for GNP, remained low at 4.1%, down from 4.3% in the first quarter, and employment continued to grow at a rate sufficient to keep up with new additions to the labor force. Civilian unemployment has remained steady at 7.3% over the past 6 months. Industry Statistics The FRB recently revised its index of industrial production and changed the base year from 1967 to 1977,1/ The revised total index shows a 0.1 % higher annual growth rate between 1967 and 1984 than the previous index. In the slower growing or declining industries, such as metal mining, primary metals, and fabricated metals, however, downward revisions in the indices and rates of growth have occurred. The previous and revised annual rates of growth between 1977 and 1984 for several of the sectors of interest to the mining industry are shown in table 2.

Jan 1, 1985