Search Documents

By L. Katgerman, H. J. Brinkman, J. Duszczyk

"The phase formation sequence in the in-situ synthesis ofTiB2 in A1 from elemental A1, Ti and B powders is identified with a combination of DSC and XRD. After the melting of A1, A1B2 and A13 Ti are formed at the contact areas between A1-B and A1-Ti. The influence of variations in starting composition on the reaction kinetics is explained in terms of there effect on the different processes in the formation sequence. Parameters in the starting composition that were investigated are; fraction ofTiB2 forming reactants, non stoichiometric Ti:2B ratio's, and addition of alloying element Cu.It was found that a liquid Al phase is necessary for the in-situ TiB2 forming reaction from the intermediate A1B2 and A13 Ti phases. If all Al is consumed by the formation of A1B2 and A13 Ti the TiB2 formation is halted until the decomposition of A1B2 and A13 Ti .Overstoichiometric amounts of B are needed for complete conversion of the Ti, present in A13Ti, into TiB2 This is explained by the fact that some of the stable A1B12 phase is formed after the decomposition of A1B2•The addition of Cu leads to an increasing reaction rate in the A1-Ti reaction. A possible explanation for this is that the A1-Cu liquid penetrates more easily between the Ti and its surface oxide than the unalloyed A1 liquid."

Jan 1, 1998

By Zhaohui Qiu, Yaguan Ji, Hong Zhong, Qingxia Liu, Yada Liu

"Water is a necessary process medium in mineral processing. For the operations where fresh water is not available, sea water could be used as an alternative processing medium to replace the fresh water if we would have built a solid understanding of the interfacial science and flotation chemistry of sulfide minerals in sea water. In this research, micro flotation of chalcopyrite and pyrite in deionized water and sea water were investigated. For chalcopyrite, the recovery starts to drop from pH 10 in deionized water and from pH 9 in sea water, and the flotation recovery close to 100% before it drops. We can found from the results that chalcopyrite flotation is depressed much at pH 11 in sea water when much white precipitate is found. For pyrite, the flotaion recovery changs a lot in deionized water with 1*10-5 M potasium amyl xanthate (PAX) as collector. It’s relatively high at pH 8~10 compared with that at pH<8 and pH>10. While in sea water, the trend is almost the same as that of chalcopyrite. Zeta potential measurements and chemical equilibrium calculation were used to find out that magnesium hydroxide species coats on the surfaces at high pH in sea water are the main reason for depressing the chalcopyrite and pyrite flotation. Through understanding the interfacial science and the solution chemistry of sea water and its impact on processing efficiency, this research will not only helps reduce the use of fresh water to minimize the disposal of spent water for environment protection, but also enhance the recovery of valuable minerals in froth flotation."

Jan 1, 2014

By D. Harrington

"There is continued activity in connection with probable reopening of old-time silver producers, but this is largely offset by other obstacles which make metal mining in Colorado a rather precarious proposition. Discussions at the joint meeting of the Colorado chapter of the American Mining Congress and the Colorado Metal Mining Association in Denver, January 20, 21, and 22, brought out many interesting facts, among them that Colorado, once a producer of high-grade ores, and with freight rates, smelting charges, etc. to accommodate high-grade ores, is now compelled to depend almost wholly upon low-grade complex ores or abandon mining, In the face of this, the railroads threaten to advance freight charges, and smelters , because of decreasing tonnage, high labor, etc., must either advance smelting charges or close (the Globe Smelter et Denver recently closed, and it is said that the Salida Smelter will close in February). A serious menace is the possibility of increase of rates by companies supplying electrical power, and the threat of the agricultural interests, now in the saddle in Colorado, to alter the laws so as to greatly increase the burden of taxation to be borne by the mines.In order to stimulate interest in Colorado metal mining, the Colorado Metal Mining Association and Colorado chapter of the American Mining Congress have planned to have an elaborately staged exhibit in the Denver Auditorium during the latter part of the coming summer, This exhibit will reproduce an old time mining camp,including mining structures such as mills, headframes, etc., as well as the camp saloons, dance and gambling halls, etc., together with mineral exhibits from many of the old time mines, no abandoned, but possibly to be reopened. due to increased price of silver, Inasmuch as the Bureau of Mines plans a National First-Aid meet at Denver in August or September, and the Rocky Mountain Mining Institute will also hold its summer meeting in Denver, it seems advisable to hold the three meetings simultaneously and it is proposed to have this done.Labor supply is fairly abundant and apparently not inclined to be dissatisfied; few, if any, strikes or other labor disturbances being found. In some mining regions advances in wages were posted January 1 and no wage reductions are noted.The Rocky Mountain Coal Mining Institute held its meeting at Denver, January 20, 21, and 22, and much attention was devoted to methods of bringing down coal without use of explosives chiefly by undercutting and subsequent use of hydraulic processes of forcing down the coal. Some attention was given the question of labor and it was suggested that the time is at hand when labor unions should be made responsible bodies by incorporation or otherwise. It was agreed to hold the summer meeting in Denver simul-taneously with the holding of the National First-Aid. and Mine Rescue Meet.In general, coal production in Colorado is proceeding satisfactorily with occasional interruption by local strikes, and tonnage is up to that being produced before the strike, but not nearly up to the record of 1918. In general, the labor supply is plentiful, but demand for coal is by no means great and unless some cold weather intervenes, it is probable that the lignite mines will have to go to a three or four day a week basis. There have been no recent disasters, but the Pictou mine of the Colorado Fuel and Iron Company encountered a heavy supply of water, and had to be abandoned until such time as arrangements can be made to pump or bale the water out."

Jan 1, 1920

By O. B. Hopkins

The reports for the years 1942 and 1943 were written in 1943 and 1944, respectively, and were summarized at the meetings of the Institute in February 1941 and February 1944, but were held in manuscript form until released for publication in 1945. 1942 During the year 1942, developments in the Peruvian oil industry continued to be subject to repercussions from the swelling war effort, which steadily diverted more of the normal supply of men and materials into war channels, and necessitated the rerouting of supply lines. The result in Peru was an increasing demand for crude oil and products. The production of petroleum in Peru in 1942 was 13,626,259 bbl., as compared with 11,935,584 bbl. in 1941—an increase of 1,690,675 bbl., or approximately 14 per cent. The largest increase, amounting to over 61 per cent, was from the Lobitos fields, but this increase was caused largely by the subnormal production in 1941. International Petroleum Company&apos;s production in the La Brea y Parinas field increased 727,111 bbl., or 7 per cent, whereas the Peruvian Government&apos;s production in the small Zorritos field declined 10,380 bbl., or approximately 20 per cent. The final production figures for the Ganso Azul field at Agua Caliente were not available for 1942 at the end of the year, but the production was believed to have increased approximately 80 per cent from 1941, or from 13,750 to approximately 25,000 barrels. Development and Exploration Exploration in Peru in 1942 was very limited and confined to areas adjacent to the older producing fields, and the efforts there were largely expended in the extension and development of the producing areas. This situation resulted partly from the shortage of transportation and drilling equipment, and also from the strong demand for increased production of oil. . International Petroleum Co. completed 69 wells during the year, including seven exploratory wells, three of which added moderate extensions to the proven areas. Sixty of the completions were oil wells and nine were dry holes. Lobitos Oilfields, at Lobitos and Restin, is understood to have concentrated its drilling effort on development rather than on exploration. The Peruvian Government operating at Zorritos confined its drilling to the development of the small producing areas previously found. During the year it announced plans to drill three exploratory wells in the Pirin area of southern Peru (see map on p. 638). It was reported that the Government had made a survey of the Sechura area (representing the southern part of the Northern National Reserve as shown on the map), but no work under this arrangement was announced. The Cia. Ganso Azul, at Agua Caliente, completed its No. 6 well as a producer on March 27, and during the year it completed the installation of a 400-bbl. topping plant.

Jan 1, 1945

By Bernd-Arno Behrens, Klaus-Georg Kosch

"In times of increasing energy costs automotive lightweight construction is gaining in importance. This paper deals with the production of hybrid steel-aluminum compounds by forging. The compound forging process is a promising method to successfully manufacture functional parts by applying resource-saving process steps. Nevertheless, challenges resulting from different material properties must be solved.The heating of hybrid material work pieces made of steel and aluminum is a great challenge. Steel is forged at a temperature of at least TSt =900 °C, while aluminum should not exceed a temperature of TA1= 500 °C. For achieving the required temperature gradient extensive experimental investigations have been carried out. Intermetallic phases form during the manufacturing process and can influence the bonding and the global part quality. In addition, methods for the characterization of the joining zone between the materials steel and aluminum are analyzed and the factors influencing the formation of intermetallic phases are determined experimentally.IntroductionIn times of increasing energy costs and stricter conditions relating to environmental protection, automotive lightweight construction is gaining in importance. The production of hybrid compounds by forging is a promising method to manufacture functional parts by applying resource-saving process steps. In compound forging a hybrid raw part consisting of a solid core, which is enclosed by a hollow casing, is joint in the forming process. This results in a graded material structure in the part in which the mechanical properties can be specifically adapted to the requirements. Compound forging is the form joining and/or firmly bonded joining of at least two different materials while plastic shape forming occurs (Figure 1)."

Jan 1, 2012

By John Jonkman

During the decade of the eighties, the mining industry was able to take advantage of numerous advancements in computing technology. The development of the desktop workstation and the tremendous increase in power of minicomputers have cause many of the technical computing applications to be taken out of the "glass house", or central computing facility, and distributed to where the work is actually performed. This trend, combined with the significant price/performance improvement being experienced, has resulted in computers becoming more readily available at a reasonable cost for research and development activities, thus increasing the amount of new development taking place. The papers in this session discuss research and development work which has resulted in advancements in mining technology applications in the following areas: - Technical Parameterization - Linear Programming - Dynamic Programming - Computer Aided Design

Jan 1, 1989

By Bruce R. Conard

Consideration of environmental and human health issues in metallurgy is growing rapidly. While not all metallurgists need to have detailed expertise in environmental and health questions, they should be aware of the challenges the metals industry faces, be able to interact with colleagues in other sciences and contribute to sound metal resource management. Hydrometallurgists occupy a unique position among metallurgists because of their knowledge of the behaviour of metals in aqueous systems, which are of fundamental importance in understanding environmental chemistry and human toxicology. As a result, hydrometallurgists should more frequently and passionately lend their expertise in assessing environmental and health risks of metals and in helping to develop effective global guidelines, regulations and process and product stewardship strategies, thereby enabling metals to continue their beneficial service to society.

Jan 1, 2003

By C. W. Hill, G. P. Luckey

In a previous article1 preliminary experiments were described, indicating the possibilities of a quantitative spectroscopic method for the determination of small amounts of lead in copper, which would be accurate and rapid, and could be carried out in the refining plant by one not skilled in chemical analysis. The present paper deals with the development of the method in the factory, giving the details of apparatus and its standardization, and presenting a comparison of the accuracy of the method with that of the standard electrolytic determination. (For variations and other applications of the method, the reader is referred to the first article.) A carefully weighed sample (0.4 gm.) of the copper to be tested is placed in a cavity in a graphite positive electrode. An arc capable of

Jan 1, 1919

By P. Braga, A. Chaves, S. França, A. Luz

"In Brazil, there are no official reserves of molybdenum, and the unofficial reserves are modest. Therefore, the molybdenum ore (molybdenite) produced as a co-product or by-product of emerald mining in the region of Campo Formoso, BA, has arisen as the only economic option. The flotation process is commonly used in Brazil for the recovery of molybdenite from emerald mining tailings, but it produces low-content molybdenite concentrates, thereby resulting in a product with low economic value. The molybdenite concentrate produced in Campo Formoso contains 83.5% MoS2 (50% Mo), which is less than the international standard product that contains > 90% MoS2 (54% Mo).This low value is due to the presence of talc, which is a naturally hydrophobic mineral that is also floated with the molybdenite during the flotation process. Separability studies were done in a Partridge-Smith cell using dextrin and quebracho as a molybdenite depressor in solution at different concentrations and pH values to produce a technical-grade concentrate (i.e., 90% MoS2). These basic studies were accompanied by measurements of the zeta potential and contact angle, which was determined by the capillary rise method. The results of these floatability studies were used in bench flotation tests, which were performed in a Denver laboratory flotation cell. A molybdenite concentrate of 93.4% MoS2 was obtained when dextrin was used at a concentration of 100 g/t."

Jan 1, 2014

By James Fisher

THE copper mines of the Keweenaw Peninsula in northern Michigan have long been of interest in connection with deep earth-temperature measurements. The extraordinary low geothermal gradient of 1° F. in 223.7 ft. announced by Agassiz1 as a result of measurements dating from 1886, although later" stated as in error, served to focus attention on this region as one offering, because of the great depth of the mines, unusual opportunity along this line. Lane,3 Van Orstrand4 and others have made valuable contributions to this study. Fresh opportunities afforded by the constant deepening of the mines, improvements in the accuracy and reliability of temperature-measuring instruments together with increasing knowledge of the heat conductivities and specific heats of the rocks, led the Michigan College of Mining and Technology in cooperation with some of the mining companies to renew work on this problem. It is planned eventually to complete a survey which will make use of the favorable opportunities for deep rock-tempera-ture measurements presented in these mines. This survey should include the determination of a depth-temperature gradient in both conglomerate and amygdaloid mines, and also the variations in temperature at the same depth in different geological formations. The first problem has a direct bearing on the question of providing equipment for necessary ventilation with increased depth. The second may show that a relation exists between the natural rock temperature and the mineral content of the formation.

Jan 1, 1932

By Christopher M. St. John, Michael P. Hardy

INTRODUCTION Geotechnical models, particularly those based on the finite element method, have been available to aid in en¬gineering design of underground mining excavations for over ten years. Despite this fact there are remarkably few cases of their use in mine design documented in the literature. It is therefore to be anticipated that many potential users of these models are relatively unaware of their capabilities and limitations and also of the form and detail of geotechnical data needed for their success¬ful application. This subsection attempts to address this problem by discussing the different types of numerical models now available and by noting how some of them have been used to study a variety of problems associated with underground mining. The subsection concludes by discussing the applica¬tion of the displacement discontinuity method to the de¬sign of possible mining systems for the copper-nickel deposits of northeastern Minnesota. The object of the analyses, which were nonsite specific, was to determine the significance of geotechnical parameters, such as ini¬tial stress and rock structure, on the stability of under¬ground excavations and hence to provide guidance for future geotechnical investigation. NUMERICAL MODELS In the geomechanical design of underground mining openings, use is made of numerical models that repre¬sent or simulate the large-scale mechanical behavior of rock. There has been less interest in analysis involving fluid flow and heat transfer, but with increasing interest in such areas as in-situ retorting and solution mining it is likely that there will be a growing need for numerical models embracing and coupling all three physical proc¬esses. However, the emphasis in this subsection will be on mechanical behavior. Models which simulate such behavior will be divided into two groups: continuum models and discontinuum models. These will be dis¬cussed in turn in order that some insight into alternative solution strategies and their merits may be gained. Continuum Models Almost all geomechanical numerical models must be classed as continuum models even though particular computer codes incorporate special provisions for rep¬resenting discontinuities such as faults, bedding planes, or joints. They are continuum models because they pro¬vide solutions for cases where material behavior is governed by the differential equations of continuum mechanics. Two basic solution strategies for such equa¬tions may be identified immediately: the differential ap¬proach and the integral approach. In the differential approach a means of approximating the differential equations over the entire region of interest is sought. In the integral approach use is made of fundamental solutions from continuum mechanics, and these are used to construct a solution to the whole problem, making approximations only on the boundaries of the region of interest. The several differential and integral methods are identified in Table 1. Differential Methods: Problems in continuum me¬chanics involve the solution of three types of partial differential equations. Two of these govern the behavior in so-called initial value problems, in which variables change both in time and in space. Examples of such problems include nonsteady heat transfer and fluid flow, and stress wave propagation. The last type of partial differential equation governs the behavior in boundary value problems. In these, variation is in space but not in time. Solution of initial value problems may be achieved in two significantly different methods: implicit and ex¬plicit. The differences between these two methods will be illustrated by considering a very simple initial value problem, that of one-dimensional heat diffusion. The equation governing this process may be written as: [ ] where T is temperature, K is thermal conductivity, p is density, c is specific heat, t is time, and x is the spacial coordinate. In finite difference form this equation might be written as: [ ] where the superscripts refer to the time and the sub¬scripts to the spacial location. Several solution strategies for this equation have been used. Two important ones may be illustrated very simply by discussing the signifi¬cance of the superscript * on the right-hand side of the equation. If i + 1 is substituted for * then the second derivative of the temperature with respect to distance is evaluated at the end of the next time step (using tem¬peratures not already known). Such an approach leads to a set of equations involving unknown temperatures and a solution procedure which is referred to as being implicit. The important characteristic of the implicit procedure is that it leads to a set of equations that must be solved for each time at which the temperature dis¬tribution is required. If instead of substituting (i + 1) for the superscript *, i is substituted, the following equation is obtained: [ ] {In this case the new temperature is defined in terms of an already known temperature distribution. The solution procedure is now known as explicit and has the impor¬tant characteristic that there are no equations that have to be stored or solved. A practical advantage of this

Jan 1, 1982

By Jinqian Zhao, Jiarong Li, Shizhong Liu

"Creep cavitation of in single crystal (SX) superalloy was investigated. The constant load creep tests, in single crystal superalloys DD6, were conducted at the conditions of 800°C/700MPa, 850°C/550MPa and 900°C/450MPa, respectively. It was found that there were square facets on the stress fracture surface, and microscopic cavities in the ruptured specimens in the vicinity of the fracture surface. Both the square facets on the fracture surface and microscopic cavities in the section of the ruptured specimens show the morphology of the same thing at the different views, namely creep cavities, which are take the form of flatten cuboid. In fact, creep cavities are the longitudinally tensiled creep cracks slowly growing during the stress tensiling. The factors of creep cracks nucleation and growth conditions include: (a) enough high temperature to activate diffusion (b) casting pores as nucleation origination (c) high strains and strain rates. Eventually, the instantaneous fracture mechanism of creep specimen is cleavage fracture.IntroductionFor the materials used in elevated temperature service, creep behavior has to be accounted for. It is well recognized that creep rupture in polycrystalline materials at high temperature occurs principally by the nucleation and growth of microscopic cavities at grain boundaries, followed by microscopic cavities linkage to form micro- and eventually macro-intergranular cracks[l,2]. Without the usual grain boundaries, SX superalloys have superior capabilities at high temperatures to polycrystalline superalloys, and have become an established feature of gas turbine technology where they are commonly employed in the manufacture of high performance blades[3]. A considerable amount of work has been done over the past tens of years, and many models for nucleation and growth of creep cavities have been proposed, however, those are mainly for polycrystalline materials.In order to improve creep resistance that single crystal superalloys, in which grain boundaries are removed, have been developed. Because there don't exist grain boundaries in SX superalloy, the mechanism of nucleation and growth of creep cavities must be different from that in polycrystalline materials.Understanding the formation and characteristics of creep cavitation is crucial to model the lives of single crystal superalloys.M. Marchionni and L.G. Zhao et al. found that there were square facets on the stress fracture surface [4,5]. Roger C. Reed pointed out creep cavities lie in the necked region[6]. In this paper, the effects on the formation of creep cavities are discussed, as well as the morphology of creep cavities and fracture mechanism of SX superalloys."

Jan 1, 2013

By John Kvinsland

"The Block 43 Project is the future home of the Paul Allen Institute for Brain Science located just off the southern shore of Lake Union in Seattle, Wash. The South Lake Union (SLU) district experienced considerable development over the last 10 years and Vulcan, Inc., which is headquartered in Seattle, is at the forefront of this transition. Once a light industrial/residential location, SLU has transformed into a hub of medical technology comprising new residential units and mixed-use buildings. Malcolm Drilling Company, Inc. constructed four shoring projects for Vulcan in this vicinity over the last year, beginning with Vulcan Block 44, which consisted of 42,000 sq ft (3,902 sq m) of soldier pile and tieback wall to support a below-grade parking facility. Block 44 construction began in February 2013 and ended in mid-April. The feature project, Vulcan Block 43, was in planning stages at the time and began construction in late fall 2013.Awarded by GLY Construction of Bellevue, Wash., in September 2013, Block 43 was the most complex of the block projects performed by Malcolm. Block 43 featured dewatering and ground improvement components along with a water-tight secant pile wall. Following the commencement of Block 43, Malcolm also began work on Vulcan Block 52 in December 2013. Block 52 consisted of 43,000 sq ft (3,995 sq m) of conventional shoring in conjunction with dewatering of 8 ft (2.4 m) of excavation located below the water table. The final Vulcan project was Block 45, which started in January 2014 for Turner Construction of Seattle and consisted of 41,000 sq ft (3,809 sq m) of conventional shoring and required dewatering to complete the final 15 ft (4.6 m) of excavation.Scope and Subsurface ConditionsBlock 43 involved a wide variety of drilling applications for the building to be constructed and properly founded. The primary scope of work involved shoring support for an underground parking structure requiring excavation of approximately 82,000 cu 3 yds (62,694 m ) of soil. The cuts for the excavation were up to 43 ft (13.1 m) in depth, and the excavation was bounded by city streets as well as the South Lake Union Light Rail on its perimeter. In order to excavate beneath the water table, an extensive, deep dewatering system was required to drain the upper fill and reduce the impact of the pressurized aquifer located beneath the excavation. In addition, drilled rigid inclusions, along with compaction grouting, were required for foundation support of the future structure."

Jan 1, 2014

department, first as a practical miner, next. as rodman on the survey corps, of which he soon became chief, then draftsman and mining engineer in the company&apos;s office. In January, 1916, he was promoted to the position of district engineer in charge of mining engineering work. He became a member of this Institute in September, 1917. Captain Ba.llamy&apos;s military experience began at the same time as his engineering practice. He was a charter member of Company A, Engineers, N. G. P., which was organized ten years ago. He saw service on the Mexican border as First Lieutenant of this Company, and remained in that position until November, 1916. In July, 1917, he was again called into service and was sent to Camp Hancock, Ga., with the 103d Regiment of Engineers. Before joining this regiment he attended a school for officers at Fort Sill, Okla., where he received special training in field fortifications. In December, 1917, he was commissioned Topographical Captain on the Regimental Staff, and in April, 1918, preceded his regiment by about six weeks to France, where he again attended an officers&apos; training school. He rejoined his regiment on July 15, near Chateau Thierry and was killed near Fismes on Aug. 9, 1918. Lieutenant Martin F. Bowles Martin F. BOWleS, born Apr. 25, 1893, at Bonne Terre, Mo., and graduated from the Neodesha, Kans., High School, had finished all but one month of a four-year course in metallurgical engineering at the Missouri School of Mines, Rolla, Mo., when on May 12, 1917, he entered the first Officers&apos; Training Camp at Fort Riley, Kans. At the close of the training period, he was commissioned a Sccond Lieutenant and assigned to Co. B, 355th Infantry, 89th Division, and stationed at Camp Funston. He left this camp with his company on May 21, 1918, and sailed from an eastern port on June 4, ayriving in England on June 15, 1918. After a short stay at a rest camp there, he proceeded to France. On August 14, he wrote that he was with Battalion Headquarters as Gout Officer, 1st Battalion, 355th Infantry, 89th Division. The last letter received from him, dated September 2, was written in his dugout and contained the following: "Here it is 2.45 a. M. Sitting in a dugout waiting for some patrols to report back in, I am writing this by the light of two candles." He was killed in action on the night of Sept. 3, 1918. The letter of notifi-

Jan 1, 1920

By W. T. Allan

Raw bituminous coal has been in general use as a blast-furnace fuel in Scotland for the last century, and although its use has now been largely abandoned and it has been replaced by coke in the majority of the few furnaces which are at present in blast in this country, coal-smelted pig iron is not yet a thing of the past; it is still being produced and marketed in competition with the more cheaply smelted product of the coke-fired furnace. Various factors have influenced this change in practice; the once plentiful deposits of coal of a suitable nature for the blast furnace are now not so easily obtainable; native blackband and clayband ironstones which are easily smelted in the coal-fired blast furnace, although still far from being exhausted, are not available except at a cost that is somewhat higher than that of imported ores, making them unattractive to the ironmaster that is compelled by circumstances to smelt his iron at the lowest possible cost. Within the last 15 years overproduction of synthetic nitrogen has led to progressive reductions in the price of sulphate of ammonia, the recovery of which together with the other by-products before that time materially assisted in reducing the working costs of the coal-fired furnace. Now the sale of the by-products recovered yields a diminished profit. When the cost of the product is the only consideration the small, s1ow-smelting, coal-fired blast furnace cannot compare with its large, modern, coke-fired competitor. Other considerations do not by any means all support the same side of the argument. In the smelting of pig iron to be used in the manufacture of steel where the quality of the final product depends so largely upon the control of the conversion process and so much less upon the physical quality of the pig iron used, the physical properties of the pig iron do not exert any appreciable influence upon the quality of the steel produced, therefore the methods employed in the smelting of the pig iron matter but little so long as the requisite chemical composition is reached. On the other hand, in ironfounding where the simple melting of the pig iron, which is the only treatment it receives before being cast into its final form, does little or nothing to modify its original charac-

Jan 1, 1937

By Christopher Mark

Knowledge of in situ stresses is fundamental to many studies in earth sciences, and coal mine ground control is no exception. During the past 20 years, it has become clear that horizontal stress is a critical factor affecting roof stability in underground coal mines. The theory of plate tectonics and the World Stress Map (WSM) project has been extremely helpful in explaining the sources and the orientations of the horizontal stresses observed underground. Recently, WSM geophysicists studying deep-seated stresses have developed a model of how stress magnitudes vary with depth in the crust. They have devoted relatively little attention to near-surface stresses, however. This paper explores the relationships between deep-seated and shallow in situ stresses in several of the world?s coalfields, using a data base of more than 350 stress measurements from underground coal mines. The analysis indicates that distinct regional trends exist, corresponding roughly to the regional stress fields identified by the WSM. The paper presents equations for estimating stress magnitudes that were developed by treating depth and elastic modulus as independent variables in regression analysis. The magnitude of the horizontal stress increases with depth, at rates that range from 0.8 to 2.0 times the vertical stress, just as the WSM ?critically stressed crust? model predicts. Overall, it seems that the stress regimes encountered in underground coal mines are closely linked to those that exist deep in the earth?s crust.

Jan 1, 2008

By Edward M. Jacobs

In some ore grinding circuits it is desirable to make separations purely on size. The normal choice for this is vibrating screen equipment. Developments in screening process technology have led to improvements in the capacity and efficiency of vibrating screens, through the adoption "Thin Layer Wet Screening". This process can reduce recirculating loads and equipment requirements in the ore grinding circuit.

Jan 1, 1985

This paper summarizes seven years of Italian ex­perience with the use of large calibration chambers for the calibration, under closely controlled stress and strain conditions, of some in situ testing devices which are used in sand deposits. At the present time two calibration chambers are operating in Italy, one at E.N.E.L.-C.R.I.S. (Milan) (*) and the other at I.S.M.E.S. (Berga­mo) (**). Both chambers can accomodate cylindrical samples 1.2 m in diameter and 1.5 m in height. A detailed description of these chambers can be found in Bellotti, et. al (1982).

Jan 1, 1987

By O. C. Wheeler

During 1938, Colombia witnessed greater activity in oil prospecting and development than in any previous year in its history; more wells were drilled, more potential production established, more geological and geophysical work was accomplished, and more leases and concessions were acquired. Many companies, including the Texas, Socony Vacuum, Richmond (subsidiary of the Standard Oil of California), the Shell, and Tropical, contributed to this activity. Probably the most noteworthy development was in connection with the Barco Concession, which forms part of the Maracaibo Basin in eastern Colombia, adjacent to the Venezuelan frontier. There a great deal of preparatory work was accomplished in addition to camp and other construction, 20 producing wells were drilled and work was begun on the construction of a 12-in. pipe line to transport the oil to the port of Covenas, a distance of 260 miles. It is reported {hat 58,000 bbl. daily initial production was established during the year and is awaiting an outlet through this pipe line. Leasing and exploratory operations in Colombia continued active throughout the year; applications were made for concessions covering more than 1,100,000 acres of national lands and, in addition, leases were taken up on large areas of privately owned lands. Under Colombian law

Jan 1, 1939

By M. Stelter

Since the first years in copper electrorefining natural products have been used as so called "additives" in the electrolyte. Glue as one of these additives offers a lot of different reactions with the metal ions and also with other additives like thiourea in the electrolyte. For a deep understanding of the effect of these additives it is important to know the routes of possible reactions in the electrolyte as well as the basics of electrocrystallization. Using this knowledge the interpretation of nodulation or inclusions of electrolyte in the cathodes in copper electrorefining is easier than before. Setting up on physical and chemical properties of the electrolyte and the additives practical investigations of the effects of additives in copper electrorefining and their impacts on copper crystallization and cathode quality are presented in this paper. Chemical deposition of glue against time and temperature are only few of the effects that are mainly caused by the use of natural products. In fact parameters like anodic and cathodic polarization are strongly affected by the additives as well as the effects of the additives are strongly affected by current density. This second part of the paper presents results concerning interactions of the above mentioned parameters.

Jan 1, 2007