Search Documents

By H. E. Hawkes

Reconnaissance mineral exploration based on the distribution of ore metals in stream sediments has become a generally accepted method of mineral reconnaissance. This approach seems to work almost equally well in all climates and in all kinds of terrain, provided of course that the ore deposits being sought are exposed at or near the surface and are actively undergoing erosion. Nobody with any experience in the field would question the validity of the concept on which stream sediment reconnaissance is based. Considerable dispute does arise, however, when the subject of density of sample sites per unit area, or sample spacing, comes up for discussion. What is the optimum balance between completeness of coverage and cost? The tacit assumption is frequently made that a greater sample density necessarily leads to more complete coverage and hence a lower probability of missing an important discovery, without regard for the size of the stream sample or the topology of the drainage pattern. The purpose of this paper is to attempt to bring the problem of site selection in stream sediment sampling into better focus, and to present a formula that may help in planning reconnaissance programs.

Jan 1, 1976

By L. C. Morales

During my College days in Mexico City, my Mineralogy Professor used to say "Mexico is the Horn of Plenty, rich in minerals, and it is easier to say which minerals are not found instead of stating all that exist. He said that the only ones missing are bauxite, diamonds and titanium ores." Today, twenty years later, a rutile mine in Oaxaca is in successful operation. Mexico has an area of approximately two million square kilometers, with volcanic activity, large shores and mountainous areas reaching as high as 6,000 meters above sea level. These conditions are favourable for most mineral deposits, some -of commercial value and others as a source of mineral samples only. (fig. No.1) In addition to vast mineral wealth, Mexico has -another valuable asset in .his people. Even before the discovery of America, natives were successfully mining metals, and during the Colonial --days, the mineral deposits were mined to increase the wealth of Spain, and it increased the --knowledge of mining. All this experience was passed along from generation to generation, and created a tradition of mining and minerals processing engineers, that currently account for approximately 182,000 persons supported by mining related activities.

Jan 1, 1994

By M. Cambridge

The extractive industries are currently, and will continue to be, major contributors to the world economy, particularly in the developing world where economic growth is dependent upon a sound supply of primary materials. However, tailings dam and other mine failures have been very much a feature of recent anti-mining publicity, particularly in Europe, and thus instrumental in inhibiting new mine developments. Although, superficially, the record of dangerous incidents might support the anti-mining position, closer inspection suggests otherwise. This paper reviews the failures which have occurred over the last 50 years and demonstrates that, though poor practice is an ongoing problem for the industry, the record is one of improvement in both design and practice. Examples are provided of significant events which have led to dramatic advances in design and operation. The paper assesses the improvements made in technology and practice, and concludes that historic events must continue to form the underlying basis for design and operation of future mining projects.

Jan 1, 2005

By J. F. Cuderman

In situ experiments at the Department of Energy's Nevada Test Site (NTS) have extended the technology of propellant-based fracturing to include liquid- filled, uncased boreholes. Previous work had developed the technology for liquid-free, uncased wellbores. Test results show that fracturing behavior is considerably more complex in liquid- filled boreholes than in the liquid-free case. Compared to liquid-free boreholes, liquid-filled boreholes have faster pressure risetimes and lower peak pressures, large hydraulic-type fractures propagating several meters beyond the end of the test zone, numerous oscillations in the pressure history, and variable types of fracturing within a single test region. Multiple fracturing is initiated in the wellbore of a fluid-filled borehole when the proper propellant mixture is used but, unlike fluid-free wellbores where up to eight fractures propagate, only one to three hydraulic- and/or shear-type fractures propagate. Hydrodynamic effects involving liquid compression during borehole pressurization appear to be responsible for the differing phenomena observed in fluid- filled boreholes.

Jan 1, 1986

By Andrew Bellamy

A thorough appreciation of the origin, formation, preservation and geometry of marine sand and gravel deposits is central in demonstrating that their extraction by dredging does not affect coastal processes or marine life. Geological evaluation underpins wave, tidal and sediment transport modeling and assists in predicting the nature and extent of seabed change during and after dredging. Marine sand and gravel deposits in the English Channel, southern North Sea and parts of the Irish Sea are of predominantly periglacial fluvial origin and record long histories of valley and floodplain cut and fill associated with Quaternary climatic and sea level oscillations. In the Bristol Channel, the influence of marine transgression and tidal dominance in sorting proglacial outwash deposits is evident in the distribution of sandbanks, scoured channels and gravel lags of this region. These deposits are relict and are unrelated to coastal sediment dynamics. Their extraction leaves seabed depressions which monitoring shows remain unfilled. The resultant offshore bathymetric changes and sediment removal in over 10 m water depth are not transmitted to the coastal zone as beach drawdown, wave height increases or sediment starvation. Applications for new aggregate dredging permissions in UK waters must be accompanied by an EIA and need to make a convincing case that the dredging will not affect rare or declining species and communities of marine life. Seabed recovery rates post dredging are now investigated and understood with reference to geological setting and the uniqueness of the sediment/biological character (biotope). Investigation of the continental shelf by the Industry and others reveals the large extent of gravel-dominated biotopes relative to commercially viable deposits.

Jan 1, 2004

By Greaves J. N

The U.S. Department of Interior, Bureau of Mines, is investigating the treatment of refractory gold ores. Chlorination in the treatment of refractory gold ores is applicable in many low-grade gold operations. When usable, this treatment provides an economic means of consuming sulfides and deactivating disseminated organic carbon. Chlorination, however, is a pretreatment technique that requires the neutralization of the chlorine prior to leaching the ore with cyanide. Research by the Bureau has extended the present chlorination technology to allow for the recovery of gold without the use of cyanide and allow treatment of some ores presently deemed untreatable by gold operators using cyanidation or chlorination/cyanidation techniques. Chlorination without carbon of two carbonaceous ores extracted between 1 and 20 pct of the gold; however, carbon-in-chlorine (CICL) treatments resulted in about 90-pct recovery with a reduction in carbon loading. A statistical design campaign for stripping metallic gold from the carbon loaded in a chlorine environment demonstrated elutions exceeding 90 pct.

Jan 1, 1991

By Chen-Ming Kuo, Esher Hsu

Energy recovery of livestock waste can not only reduce waste pollution but also generate renewable energy and further create economic bene fits. Currently, most of livestock waste in Taiwan is treated as waste without efficiently recycled. This paper aims to explore and evaluate the energy recovery of livestock waste in Taiwan and further provide policy suggestions. Study results show that small farming scale of livestock industry in Taiwan leads to a lower efficiency of biogas energy recovery. Besides, the environment with relative low price of electricity and high invest cost for power generation plant is hard to provide incentive for implementation of energy recovery which has further caused difficulty on policy promotion for renewable energy recovery of livestock waste in Taiwan. Policy reform with increasing FITs and differentiated purchasing rate for biogas power is suggested to stimulate energy recycling of livestock waste in Taiwan.

Mar 1, 2017

By I. Weir-Jones

I. Introduction The experimental work described in this paper was carried out during 1967 and 1968 in an inclined reinforced concrete adit which had been driven during 1965 and 1966 to provide primary access for a new gypsum mine. The new mine was situated near the village of Sherburn-in-Elmet in central Yorkshire in an area of extensive post-glacial plains of deltaic and lacustrine origin. These plains cover a large area of this part of Yorkshire extending inland from the coast for a distance of about 35 miles. The gypsum deposit at Sherburn dates from Permian times and it is considered" to have been associated with the western-most edges of the ancient Zechstein Sea which was also responsible for the formation of the extensive evaporite deposits in north-east Yorkshire. The gypsum deposit, which varies in thickness from 10 to 15 feet, is extremely pure and it occurs quite close to the surface; in the Sherburn area the overburden is only 120 feet thick. The proximity of the deposit to the surface, however, tends to give a somewhat false idea of the magnitude of the problems associated with its extraction. These problems were all related to the nature of the overlying strata. As has already been mentioned, the surface deposits are post-glacial and they consist of an extremely large number of thin layers of varved clays, fine silts and sands extending down to a depth of 75 feet. From the bottom of the post-glacial deposits to the seam, a distance of about 45 feet, the strata consists of a succession of marls, weak sandstones, and siltstones, which although they are inherently incompetent materials, are appreciably stronger

Jan 1, 1971

By R. F. Holub, E. Franco, T. B. Borak, K. J. Schiager

INTRODUCTION According to a recent analysis by Schiager et al.(1981), inhalation of radon daughters continues to contribute the largest risk from exposure to radioactive materials in underground uranium mines. The American National Standards Institute (1973) has published a concensus standard for radiation protection in uranium mines. According to this standard, a monitoring system for radon daughters must be capable of measuring the annual accumulated exposure in working level months within an uncertainty interval of 50% at the 95% confidence level. To satisfy this criterion, uranium mining companies in the USA have adopted a procedure consisting of single or periodic measurements of the air concentration of radon daughters. All of the measurement methods sample a known volume of air through a filter. After a specified delay interval, the filter is analyzed for radioactivity. The exposure rate from total airborne potential alpha energy in units of working level (WL) is estimated from the measured activity on the filter. For control purposes, this measurement establishes whether or not a work area is safe for occupancy by miners. For routine dosimetry, the concentration estimated from the grab sample is assigned to the appropriate work area. It is then assumed that the concentration of radon progeny is equal to the average of the two measurements at the beginning and end of the specified interval. Meanwhile, the work locations and exposure times of each miner are recorded on the daily time card and verified by the shift supervisor. Most cards provide space for 15-minute time intervals. The exposure in working-level hours (WL-hr) for each shift is obtained by summing the time spent in a given location multiplied by the exposure rate (WL) assigned to that location.The exposure of an individual miner to radon progeny is summarized on a weekly basis and commonly reviewed each month. These values are then accumulated in units of working level- months (WLM) during the calendar year. EVALUATION TECHNIQUE AND RESULTS The evaluation of grab sampling methods for monitoring exposure to radon progeny is presented in two sections. The first section examines each method individually according to accuracy, precision, and uncertainties attributed to human errors. The second section includes an analysis of procedures which are common to all measurement methods. The ultimate goal is to determine whether a specific measurement method, or grab sampling in general, can fulfill the criterion that the annual accumulated exposure of each miner be known to within ± 50% at the 95% confidence level. In addition it is essential that the above criterion be satisfied at an acceptable cost to the mining company. The results of each testing procedure are presented in terms of the contribution of the relative uncertainty in the estimates of cumulative WLM. Each of these are then combined to form a figure of merit for the complete monitoring system. The method of combining statistical uncertainties and interpretation of the results is subject to some debate. However, since all of the tested parameters enter into the final computation of WLM multiplicatively, we have used the commonly accepted procedure of combining the squares of the relative uncertainties. We have also assumed that each of the uncertainties is derived from independent random variables and the covariance of any two variables is zero. A description of each grab sampling measuring method is given in Table 1. Also included is the equation used to compute WL from the measured quantities. Accuracy (U A) Our definition of accuracy is based on the uncertainty inherent in any method which attempts to estimate potential alpha energy without unambiguously determining the concentration of the three unknown radioisotopes, RaA, RaB and RaC. (For simplicity, the RaC and RaC' nuclides are referred to in combination as RaC.) The inherent uncertainty strongly depends on the mixture of these three components at the time of measurement.

Jan 1, 1981

By Robert W. Hunt

THE memorable features of American history have been making fast during the last century, and notably so since 1860; and they are by no means confined to political or to any one branch of scientific development. Of all the industrial arts, none show a greater change or a mightier progress than the Bessemer manufacture. And this year, while we are celebrating the first centennial of our national life, we can also celebrate the first decennial of American Bessemer practice. While not forgetting or undervaluing what has been done in other countries, I have thought that a brief history of the introduction and development of the Pneumatic or Bessemer process in America would be of interest. In 1863 the Kelly Pneumatic Process Company was formed and an arrangement entered into with William Kelly, who had taken out letters-patent of the United States, Nos. 16,444 ; 17,628, re¬issued as 505; 18,910, dated January 10th, 1857 ; June 23d, 1857; November 3d, 1857; and December 22d, 1857, respectively. This association was composed of the Cambria Iron Company, E. B. Ward, Park Brothers & Co., Lyon, Shorb & Co., Z. S. Durfee, and, later, Chouteau, Harrison & Valle joined the combination. Not satisfied with possessing the control of the Kelly patent, they sent Mr. Z. S. Durfee to England, to secure for this country Mushet's patent on recarburization, No. 17,389, dated May 26th, 1857, the same having been taken out in England on September 22d, 1856. In this Mr. Durfee was successful. Previous to the application of William Kelly for a patent, Henry Bessemer, of England, had taken out patents dated February 12th, 1856, and August 25th, 1856, in this country. Kelly claimed priority in the discovery of the principles of the process, and the Patent-office allowed his claim by granting him his patents. In the autumn of 1862 Mr. Alexander L. Holley, while in England, was impressed with the importance of Mr. Bessemer's inven¬tion, and so fully foresaw its future, that, upon his return to the United States, he induced Messrs. John A. Griswold and John F. Winslow, of Troy, New York, to join him in endeavoring to possess Bessemer's American patents. Mr. Holley returned to England in

Jan 1, 1877

By Lester Uren

The fluid level maintained in wells pumped for oil is an important factor in deter-mining their productivity but one that has received little attention in the literature relating to petroleum-production technology. In the present paper the writer undertakes to show how and to what extent fluid level influences productivity and suggests the use of a fluid level indicator as an aid to the oil producer in maintaining the fluid surface within the well at the proper position. IT is realized that the depth of fluid maintained in a pumping well is sometimes influenced by other considerations than the quantity of fluid that will enter the well: the prevention of sand incursion, prevention of waste of natural gas, and the maintenance of a suitable submergence for the pump, for example. These latter factors have an important influence on the productivity of the well, so that otherwise unwarranted fluid levels must sometimes be maintained to offset them; but where the handling of unconsolidated sands is not a problem of consequence and where water has been properly excluded, the principles developed here and the practices recommended, should apply. The principal objective of the producer should be to produce the maximum quantity of oil in the shortest possible time. Any method or equipment that will increase the rate of production during the early years of the life of the well, when gas pressure is high, will greatly augment the .ultimate production. The maintenance of a proper fluid level in the well at all times will go far toward accomplishing this desired result. For a given set of conditions surrounding the flow of oil into a particular well, in which the viscosity of the oil, the porosity and grain size, of the sand, and the diameter of the well appear as constants, two variables determine the quantity of oil that will flow from the sand into the well. These are: the effective pressure behind or within the oil in the reservoir sand, and the fluid level maintained within the well.. The former is the expulsive force that causes movement of oil from the sand into the well, while the latter determines the magnitude of a resisting force opposing such movement. The first of these factors is largely beyond the control of the oil producer, but it is in his interest to reduce the opposing force to the lowest economic limit.

Jan 2, 1925

By H. M. Rutherford

The reflection method in seismic prospecting has aroused much interest in the past few years. The purpose of the present paper is to present the method of reflections in the mapping of geologic structure and also to give some indication of its limitations. The reflection method is well adapted to the mapping of geologic structure in the Mid-Continent fields, and has been found most useful there. The refraction method is ideally suited to the finding of structures, such as domes, where the amount of relief is very large. This explains the brilliant success of the refraction method in the Gulf Coastal region of Texas and Louisiana. The additional fact that salt has a much higher velocity than the surrounding sediments made their discovery much easier. By the use of the reflection method, differences of relief of 25 to 50 ft. to the mile may be detected at a depth of 5000 ft., and the depth points accurately plotted on a map. This is hardly possible by the use of the refraction method. The reflection method has been in almost continuous use in the Mid-Continent area since 1926, but very little, if anything, has been published until recently'(7) † regarding either the method or the results. The discovery of several oil fields is now attributed to the use of the reflection method. Reflection methods have been used by the Germans to find the thickness of the ice of several glaciers. (2,8) The depths there considered were of the order of only a few hundred feet. For the method to be of any practical value in this country, it must be able to work to depths of several thousand feet. As was indicated above, this is now possible, though there are many problems connected with the reflection method yet to be solved. The refraction method requires that the shooting be done over long ranges. It was necessary, for example, to take distances out to several miles in order to penetrate some five thousand feet. Naturally this uses a good deal of dynamite. In the reflection method the distances are much shorter and the amounts of dynamite are much smaller, within limits which will be noted below. The chief distinction between refraction and reflection methods is to be found in the analysis of the seismo-gram. Refraction shooting makes use of only the first arrival of energy

Jan 1, 1934

By F. G. Smith

Abstract Laboratory methods are now in use whereby the temperature and pressure during the crystallization of hydrothermal minerals can be determined. The techniques include the use of the decrepitation method of studying liquid inclusions, and electrical measurements of pyrite. The determinations are sufficiently accurate that the data can be used in solving a variety of ore deposition problems. Within the last year, several new laboratory techniques have been developed in the Geochemical Laboratory of the Department of Geological Sciences, University of Toronto. The results of several tests of ore by these methods have proved to be useful in treating some problems which previously were considered unsolvable. It is now possible to determine the temperature of deposition of most of the minerals in a hydrothermal ore deposit, also the depth below the surface during deposition. Measurements can also be made of the reopening history of a complex ore. The temperature-pressure determinations depend upon the fact that minerals deposited from a hydrothermal solution always trap a small amount of the solution at the time of crystallization. The solution, being predominantly composed of water, has a density which depends upon the temperature and the pressure prevailing during crystallization. After ore deposition is complete, erosion and isostatic uplift finally exhumes the vein. During this slow fall in temperature and pressure, the solution contracts and a gas bubble appears. If the trapped solution in the mineral is examined, the gas-liquid ratio records the density of the solution at the time the mineral was deposited (except for a slight change in the volume of the mineral). The thermal expansion and compressibility of water and water solutions are known to a sufficient degree that, if the gas /liquid ratio can be determined, the temperature-pressure relations during deposition can be calculated.

Jan 1, 1949

By J. J. Jakosky

The strategic importance of the metallic minerals in our industrial economy, and the declining rates of discovery have focused attention on means of exploration for new mineral deposits. A consideration of exploration techniques leads to an attempt to evaluate the effectiveness of geophysics as a tool for mining exploration. One means of evaluation will be to compare the use of geophysics in petroleum exploration with its possible uses in mining. Geophysics in Petroleum Exploration During the past twenty years, the petroleum industry has established an effective exploration technique. Geology is the basic tool in those areas where reliable predictions can be made from surface conditions. In the other areas, where the geological studies are inadequate, they must be supplemented with geophysics or direct exploration, such as drilling. Since geophysical work is far less costly than any form of direct explbration, it is used almost exclusively as the means for obtaining the desired subsurface information. The geological and geophysical techniques are credited with locating sites which yielded one producer for three dry holes during the year 1947.' For the wells located without geology or geophysics, there is a ratio of one producing well to sixteen dry holes. From these figures it is seen that the geological and geophysical techniques are more than four times as successful as the nontechnical exploration. It will be in order to consider further this ratio of one producer to three dry holes. The geophysical methods in use today† do not pretend to locate oil directly; their function is to locate anomalies or structures favorable for the accumulation of oil. For a producing oil well we must have not only structure, but also other favorable conditions, namely: petroliferous source beds, the required porosity and permeability in the reservoir rocks, an impermeable cap rock over the reser- voir, and the necessary water or gravity drive to force the oil into the bore hole. Since the geophysical work can only detect and sometimes delimit the anomaly, these other necessary conditions can be determined only by direct exploration. The success of modern geophysical work in locating and limiting the structure itself is remarkably high, probably over 95 pct accurate. Geophysical work renders an important service in the delineation of the structurally unfavorable areas and their elimination from the drilling phase of the exploration program. When attempting to locate any material of scarce occurrence in the earth, it is of paramount importance to know where not to dig. This elimination of barren areas is the least appreciated but is of great economic importance. For illustration, the difference between one producer to three dry holes, and one producer to sixteen dry holes, represents a saving of thirteen drilled wells, which would require an expenditure many times the cost of the geophysical work that might have revealed the nonfavorable structural conditions. The percentage of geophysically-located wells necessarily will continue to increase in the statistics of future years, as the search for oil is extended

Jan 1, 1950

By J. G. Paterson, J. A. Meech

Abstract-Activated carbon is a strong adsorbent for amyl xanthate, capable of removing from solution up to a quarter of its own weight in xanthate. In selective flotation systems where depression is unstable, separation efficiency increases with activated carbon additions. The improvements observed are brought about by two mechanisms. First, by removing stripped and residual collector ions from solution, competition between depressant and xanthate is reduced and depression is stabilized. In addition, the texture of the froth phase at high pine oil concentrations is modified by activated carbon such that better drainage between the air bubbles takes place, alleviating the mechanical entrapment of depressed mineral particles. In treating a bulk copper/lead concentrate produced from GECO ore, selectively between galena and chalcopyrite is increased when activated carbon is used. Although the rate of flotation of galena is marginally lowered by activated carbon, a small extension in the duration of flotation allows the lead recovery to increase by 19% at the same recovery of copper. An addition rate of 0.75 kg/ton (1.5 lb/st) of bulk concentrate is suggested as optimum from this testwork. However, the actual level wed in the mill is dependent upon the residual concentrations of collector and frother in the bulk concentrate Pulp.

Jan 11, 1978

By Joseph G. Wargo

An investigation of trends in exploration expenditures for a selected group of mining companies was undertaken for the interval 1968-1971. These trends were compared with financial factors that are associated with various groups of companies and the implications of these trends are indicated. The sample consists of 21 mining companies, of these, 19 are listed on the New York Stock Exchange and 2 are listed on the American Exchange. Twenty are American, one is Canadian. All are fundamentally "mining companies" in that they derive the bulk of their income from the ex- traction, sale, and at times, fabrication of metals from their own mines. This is in contrast to companies which have mineral exploration departments but derive the bulk of their revenues from sources other than mining, such as oil and gas sales. No companies which can be considered strictly as exploration companies are included in the sample. This definition held up in 1968, however, its strict application became more difficult through the years. In 1971, three or four of the companies were changing their character in that they were phasing out of the mining business and deriving a substantial part of their income from activities other than mining.

Jan 5, 1973

By Jeffrey F. Adams

Gypsum fouling is a common problem in the hydrometallurgical industry. It is a particular problem in free sulphuric acid neutralization, or iron removal operations where sulphates are removed from aqueous solutions by the addition of calcium-containing bases. Previous work revealed a strong correlation between the degree of gypsum supersaturation in the reactor and the rate of scale growth indicating that scale formation and growth are primarily controlled by chemical phenomena. However, the chemical behaviour of gypsum is variable and unpredictable with solution chemistry and temperature. Many of the "rules of thumb" that are used to predict its behaviour (and avoid fouling) are in fact based on gypsum solubility in water, rather than on real mixed metal sulphate systems. However, despite this unconventional solubility behaviour, we have been able to accurately model it in Ni, Mg, and Zn containing solutions over a wide range of temperature (25°C-90°C) and solution concentration (0-6 m) using the OLI simulation software. Furthermore, by studying fouling rates in a simulated continuous neutralization reactor, the relationship between process conditions and fouling rates were explained for the first time. This has led to an understanding of how techniques for minimizing gypsum fouling work.

Jan 1, 2003

By Allen D. Look, J. Howard Bird

"INTRODUCTION The Phelps-Dodge Corp. New Cornelia Branch open-pit copper mine operated without a fatality in the drilling and blasting department from December 13, 1937, to April 1, 1947, and continuing.Between the dates named the explosives crews had a total of 746,520 man-hours of exposure and handled 12,000 tons of explosives, over 770,000 detonators, 2,300,000 feet of fuse, and 7,700,000 feet of Primacord in loading holes to break 116,780,000 tons of material.It is the purpose of this paper to record the procautions taken to insure safe handling of explosives at this operation where safety is definitely a matter of forethought rather than chance.GENERAL INFORMATIONThe New Cornelia Branch open-pit mine operates on a large, low-grade, disseminated-copper deposit about one-half mile south of Ajo, Ariz. The pit is approximately oval; the ore body being some 4,800 feet long and 2,750 feet wide. Ore is mined with electric shovels loading into railroad cars. All benches in- the pit are 40 feet in height except two, which are 60 feet high.The New Cornelia ore body differs from most porphyry-copper deposits in being hard and siliceous. In common with the other low-grade porphyry-copper deposits, continued operation is possible only with economical handling of large tonnages. This has necessitated a great deal of study in the evolution of a safe and efficient method of handling the large quantities of explosives needed in breaking this hard-rock material."

Feb 1, 1948

By James E. York

The honor so fairly earned and so incompletely and tardily paid to Henry Cort, the inventor of the puddling-furnace and the rolling-mill, has been fully set forth by Mr. Charles H. Morgan,' and needs no further emphasis here. In view of the importance of the rolling-mill in the treat ment of iron and steel, the paucity of information concerning it is surprising. With the exception of a book, written about 35 years ago, by Peter Ritter von Tunner, an Honorary Member of this Institute, and of desultory articles on simple sections, which have appeared in technical journals, I know of no publication attempting to treat this subject, although volumes have been written on the scientific theory and technical manipulations involved in other branches of the iron- and steel-industry. This strange anomaly may be due to the fact that roll-turning cannot be called a scientific business. It does not ordinarily come within the range of an educated engineer; yet it cannot be performed by an ordinary mechanic. It demands some of the qualifications of an engineer, in designing, and those of a mechanic, in execution. The men who have followeci this trade have controlled the training of their successors. In many cases the technical knowledge required has

Jan 1, 1907

By Robert Pring

IN addition to the humanitarian aspects of a dust-control program, certain economic benefits are becoming more fully recognized and now furnish a greater incentive to the mill operator to eliminate the dust from his plant. It is well known that a favorable working environment promotes increased efficiency and improves the morale of em-ployees, with a consequent decrease in labor turnover rates. One progressive mining company estimates its direct and indirect labor turnover costs at from $40 to $50 per man; for skilled labor, such as machine operators, the cost may approach $100 per man. While these figures may not be typical of every plant, they do indicate a potential savings in operating costs. Dust signifies waste; its elimination de-creases maintenance costs of mechanical and electrical equipment; its recovery is often justified from the standpoint of values contained in the collected material, although in large-scale milling operations handling low-grade ore this may not be an important factor. Perhaps the most significant trend in industrial sanitation is that dust-control equipment and procedures are becoming recognized as integral parts of the mill flow-sheet. Exhaust ventilating systems are now afforded equal care in design and mainte-nance to that given other machinery more closely related to the process,

Jan 1, 1940